Search Documents

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O'Neill1 observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in intergranular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by 10 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle' in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. [ ] In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1941

By Henry J. Kaiser

A few months ago I had the honor of addressing the Society of Mining Engineers annual banquet in Sun Francisco. I have since been asked to amplify some of the remarks I made at that time concerning the management policies of the Kaiser organization and various aspects of our corporate thinking. This is a difficult task for an insider like myself. I look at the different companies, and the men who run them, and it is hard to think of these men in terms of policy or procedure. Actually I prefer the term management philosophy to either policy or procedure. My father, Henry J. Kaiser, is not only the founder but the guiding spirit of our organization. His philosophy, and in turn that of the organization, centers around two concepts, service and accomplishment.

Jan 1, 1960

By Edward W. Parker

At the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899,I presented a paper on this subject entitled, Coal-Cutting Machinery,' which has become somewhat out of date, in view of the decade's development in this feature of the coal-mining industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is "shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the U. S. Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent. in 1907 to 37 per cent. in 1908. In 1898 only 19.5 per cent. of the total product was unclercut.by the use of machines. The number of in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 mas almost exactly double that of 1898, while the machine-

Jan 1, 1911

By John C. Shyne, Eric R. Morgan

WHEN temper rolled low carbon sheet is stored at room temperature before use, changes take place in its mechanical properties. This phenomenon is known as strain aging. Normally these changes are observed by means of Olsen ductility and Rockwell B hardness tests but' unfortunately such tests are relatively insensitive. Strain aging can be readily observed in the laboratory by means of tensile tests. The tensile test method is even more sensitive if the aging is allowed to take place in specimens which have been prestrained in tension rather than by cold rolling. In fact one of the great benefits of commercial temper rolling is that it introduces a residual stress pattern which tends to mask the effects of strain aging when the sheet is finally used in a pressing operation. Curves B, C, and D of Fig. 1 illustrate the changes that take place during the aging of commercial rimmed steel at room temperature following straining in tension, curve A, Fig. 1. The first important change that can be observed is an increase in the stress required to produce plastic flow. This increase is, in this paper, called the aging index. As aging proceeds and the aging index increases, there is also an observable return of the yield point, an increase in the ultimate tensile strength, and a decrease in elongation to fracture. The results of strain aging in deep drawing steel manifest themselves as stretcher strains (L?ders bands) buckling, 2nd tearing. In deep drawn parts such effects are undesirable and strain aging is a serious problem. The rate of strain aging of a steel depends upon its composition and prior mechanical and thermal history? but for most temper rolled ope

Jan 1, 1958

By M. King Hubert

The growth of human knowledge is an evolutionary process. Historically our separate sciences came into existence as people became interested in various apparently unrelated domains of phenomena, and in this manner we acquired the sciences of physics, chemistry, astronomy, biology and geology. As various of these sciences became established, cognizance of them came to be taken by the universities and in this manner there arose the traditional departments of physics, astronomy, chemistry, biology and geology of our American universities. As there was no particular rationality in the boundaries separating the various sciences, in the university departments the jurisdiction of each has assumed quite arbitrary limits. In the domain of earth phenomena the first science to grow up was that of geology, which arose originally from the activities of the collectors of rocks, minerals and fossils. Thus geology evolved as a descriptive science dealing with directly observable terrestrial phenomena for which elementary rational explanations were offered. The traditional treatment of phenomena by the science of geology has rarely been with more than an elementary regard for the fact that these phenomena were also phenomena of physics and chemistry. Since the latter part of the nineteenth century, a new approach to terrestrial phenomena has been emerging and becoming of so great a significance that it can no longer be ignored. This approach has been made by people trained primarily in the sciences of physics and chemistry, who have investigated terrestrial phenomena as constituting phenomena of their respective sciences. In this manner we have acquired the so-called "borderland sciences" of geophysics, the physics of the earth, and of geochemistry, the chemistry of the earth. Neither of these fields is new, having arisen chiefly at the hands of European investigators during the latter part of the nineteenth century. The European universities have long since given official recognition at least to geophysics, by the establishment of departments or institutes of geophysics, which are on a par with the university departments of the other sciences.

Jan 1, 1940

By O. S. True, C. H. Herty

It is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open-hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCancel states that such is not the case. The experimental work was carried out to confirm the results of Roh12 as to the reversibility of the reaction. Six trials are herein considered. In each 200 gm. of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent, of sulfur in each. In runs 5, 6 and 7, metallic manganese and iron sulfide to give the same proportions of. manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots. The results of these melts are as follows: Ingredients of Charge Analysis or InRot ManOaneBe, SulfUR, ManOaneBe. SULFUR, Run Material Charged PeR Cent. PeR Cent. Per Cent. PeR Cent. 2 MnS + Mn............... 1.0 0.452 0.636 0.367 3 MnS + Mn............... 2.0 0.50 1.57 0.310 4 MnS + Mn............... 4.0 0.50 2.81 0.230 5 FeS + Mn................ 1.0 0.50 0.647 0.397 6 FeS + Mn................ 2.0 0.50 1.45 0.374 7 FeS + Mn................ 4.0 0.50 2.73 0.195

Jan 1, 1925

By J. S. McNeil, J. U. Messenger

In the drilling of oil wells the control and prevention of lost circulation of the drilling- fluid is a oroblem which is frequently encountered; in many cases existing materials and methods for alleviating this condition have not been adequate. For severe cases of lost circulation in which the simpler methods, such as application of various bridging materials to the mud system, have proven unsatisfactory. a new material and method for applying to the loss zones have been developed which appear to he superior to existing techniques in many respects. The material, called a clay cement, is capable of being handled as a drilling fluid after initial mixing of the solitl ingredients with water and may be pumped down the drill pipe and squeezed into loss zones. After a short period, the material develops a very high gel strength which seals off the zone against further losses of the drilling fluid. In field tests, the process has been demonstrated to be a very effective method for combatting lost circulation. INTRODUCTION Methods of treating lost circulation in rotary-drilled wells by the addition of special materials to drilling fluids have long been in the process of development and are continuing to improve.' However, the annual drilling costs which can be traced directly to lost circulation difficulties still run into the millions of dollars. The loss of mud materials into highly permeable zones may range up to $50,000 per well in some areas. In addition to mud costs, excessive requirements of casing, cement; rig time, and the attendant blowout hazards further emphasize the importance of the need for improved methods of combatting lost circulation. The shortcomings of presently-used materials and methods have led to the development of a new lost returns material in the form of a time-setting clay cement. In field tests this material has proven very successful in plugging off loss zones. which other more conventional materials had failed to do. REVIEW OF PRESENT CORRECTIVE MEASURES The proper control of such operating factors as pump pressure, clearance between pipe and hole, and speed of running pipe in a holez is of primary importance in preventing and minimizing lost circulation problems. These factors, however, concern matters of drilling technique and do not directly involve lost circulation materials. Aside from setting casing past loss zones, three principal methods are generally employed for the purpose of avoiding or combatting lost circulation: (1) adjustment in properties (principally density) of the drilling fluid, (2) addition of fibrous, flaky, granular or other types of bridging materials to the mud system, and (3) the application of cements to the loss zones. The latter method is usually employed only after the first two have proven unsuccessful. In Table I are listed some advantages and disadvantages of the common corrective measures. Frequently, a combination of bridging material and cementing material is used." This combination is based on the premise that a bridge will

Jan 1, 1952

By Heihachi Kamura

The reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe2O3 + 3CO = 2Fe 4- 3CO2 2Fe2O3 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of earbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing equation, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also on the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium. Chemical Equilibrium of Iron, Oxygen, and Carbon Investigations concerning the equilibrium between iron, oxygen, and carbon have been carried out by E. Baur and A. Glaessner,1 who deter-

Jan 1, 1925

By C. O. Brawner

Introduction The procedures used to design slopes in rock have only been developed over the past 10 years. Therefore, continued review and assessment of field experience by the publication of case studies is necessary to determine the accuracy of the theory and the application of the design techniques being used. Where failures have occurred, mine management should insist that the slides be 'back analyzed' to determine the shear strength parameters at failure. These values should be used for any pit design as they reflect site conditions more accurately than any other procedure. The previous papers have dealt with the basic concepts and factors that influence stability. To illustrate the application of these concepts in the study of practical stability problems, six ease studies have been selected for review. The examples include failure of tailings dams due to an earthquake, failure and redesign of a slope in overburden, review of failures of rock slopes, calculation of the amount of seepage into a pit and influence of the groundwater on stability, and the design of slopes for a proposed 2,500 ft. deep open pit mine. All but the first example are drawn from the authors personal experience. EXAMPLE 1 Failure of Tailings Dams Due to an Earthquake On March 28. 1965 a serious earthquake occurred in Chile with the epicenter located near the town of La Liqua, about 80 miles north of Santiago. The earthquake had a rating of 7 to 7.25 on the Richter scale. A record of the acceleration was taken at Santiago where a maximum horizontal acceleration of 0.18 g. was recorded. Many small mines are located in this region. Each of the mines provided impoundment storage for tailings with one to three dykes. As a result of the earthquake, most of the dams failed. The most serious failure involved two dams at El Cobre where more than 2,700,000 cu. yd. of tailings flowed into the valley, travelled over 7 miles in a few minutes, destroyed part of the town of El Cobre and killed more than 200 people. The Chilean government commissioned an investigation into the failures. A summary of the findings was published by Dobry and Alvare7 in 1967 (1). The location of the earthquake and the tailings dams which were investigated is shown

Jan 1, 1971

By Stuart H. Ingram

The term lightweight aggregate implies material which may be substituted for the usual rock, sand and gravel commonly used as the major part of concrete, but distinguished by being much lighter in weight. Background The art of making and using concrete is old and well developed. Research and experience have pretty well determined the qualities necessary in its constituents, and time has tested theories and applications. Elaborate specifications and tests have been devised and generally adopted governing all phases of concrete work, from selection of material, through engineering design and down to mixing and placing. Standard practices have become routine to executives and laborers, and operations have been simplified and costs lowered. Though many lightweight aggregates meet the basic specifications necessary for usefulness, their physical qualities are so different that they fiequently will not pass standard tests, and some of them cannot be mixed and placed with the usual formulas for water and slump. As a rule their use produces a concrete with a lower modulus of elasticity which requires design change, and being produced in much smaller quantities than ordinary aggregate, production costs are higher. This latter works in a vicious circle to restrict their use and maintain prices that are not competitive, except as against each other. Increased Demand In spite of such handicaps consumption has grown steadily for the past two decades and is apparently growing even faster today. It is evident that lightweight concrete must have better qualities, and be sufficiently better to Overcome the higher cost and the other difficulties and disadvantages pertinent to the use of a new and different material in an old industry. Hence the study of its main ingredient should be of interest to all engineers. Our group has a double interest in the subject since most of the materials which have been used as sources of lightweight aggregate are either mined, Or are by-products of mining operations. We are directly interested in their production as well as their use, and since available supplies of materials suitable are limited, the increasing use, and rising demand, make the discovery of new Or or the development of processes to adapt other natural materials to this use, a promising field; and one in which our profession should take an active part. Recent Development Descriptions of ancient work contain references to the use of spalls of tuffs Or pumice in concrete masonry, but it is only since the nineteen twenties that serious attempts have been made to produce and market lightweight aggregates. A period of rapid advance in theory and practice in cements, mortars and con-

Jan 1, 1948

[United Engineering Society WALTER H. ALDRIDGE J. VIPOND DAVIES J. V. N. DORR Engineering Societies Library Board SYDNEY H. BALL ALEXANDER C. HUMPHREYS GEORGE C. STONE JOHN H. JANEWAY Engineering Foundation Board H. M. BOYLSTOX J. VIPOND DAVIES GALEN H. CLEVENGER]

Jan 1, 1928

By B. C. Craft

The principal events in the oil and gas operations for Louisiana during 1933 have been the rapid development of the Converse field in Sabine Parish, the discovery of three new salt domes, one in North Louisiana and two in South Louisiana, increased development in the Iowa field on the Calcasieu-Jefferson Davis Parish line, and extensive geophysical operations over a wide territory. Other miscellaneous events worthy of mention are the continued leasing of prospective oil lands over a wide area, extension of production at the East Hackberry field, Cameron Parish, discovery of deep sands at Caillou Island, Terrebonne Parish, and the completion of several important wildcats. Despite proration, oil production showed a substantial increase during 1933. The total output for this area was 25,599,802 bbl. as compared with 22,507,387 bbl. during 1932. North Louisiana There were 111 oil wells and 47 gas wells completed in North Louisiana during 1933 as compared with 109 oil wells and 33 gas wells during 1932. North Louisiana oil production decreased approximately 692,625 bbl. in 1933 from its 1932 figure. The normal decline in the old fields was partly offset by increased production at the Zwolle and Converse fields in Sabine Parish. Acid treatment of wells in the Zwolle, Converse and Monroe fields was highly successful. The method of application has been described by H. K. Shearer, Geologist, Pelican Natural Gas Co., as fo1lows:l With tubing in the hole and standing valve removed, the casing is filled with oil to the surface. The limestone solvent is pumped in through the tubing, at the same time bleeding off enough oil from the casinghead to equal the volume contained in the tubing plus the volume of open hole to be treated. The amount of solvent used in most of the wells treated was 1000 gal., which is enough to dissolve about 11 cu. ft. of chalk or limestone. After the computed amount of oil is bled off, the casinghead is closed and the remainder of the solvent is pumped in at whatever pressure is necessary to force it into the oil-producing horizon. The solvent is followed up with enough oil to

Jan 1, 1934

By Keith C. Hendrick

The mining industry of Canada, stretching from coast to coast and reaching into the most remote regions of the country, is of fundamental importance to the national economy and the well being of many communities outside the main urban areas. The production, processing and transportation of a host of mineral products provide employment for about 9% of the country's labour force; and their shipment to export markets provides an important contribution to the balance of payments. In 1976 Canada's metal and mineral production had a value of $5.24 billion, of which zinc and lead accounted for $862 and $129 million respectively, or 19% of the total. By all standards the Canadian zinc and lead industry is large and, therefore, important to the country as a producer and the world as a supplier. This report will review the development, describe the present status and discus current problems and future potential of the industry. The discovery and successful development of the major lead-zinc deposits at Kimberley, British Columbia, provided Canada with a solid base from which to grow. The breakthrough in metallurgical technology using differential flotation to separate the lead and zinc sulphides and the refining of high purity metal by electrolytic methods not only helped Canada to compete with other world producers but also provided a new source of these metals at prices and qualities that encouraged the development of new end uses.

Jan 1, 1977

By Frank L. Antisell

Certain physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. The physical standard includes electrical properties, defects in the "set or casting," variation in dimensions, weight, etc. Paragraph 4 of the specifications states, " Wire bars, cakes, slabs and billets shall be substantially free from shrink holes, cold sets, pits, sloppy edges, concave tops, and similar defects in set or casting." Shrink holes and concave tops indicate both physical and metallurgical defects; cold sets, sloppy edges, etc., indicate physical defects only; small pit holes may be indicative of either or both physical and metallurgical defects, depending on conditions under which they originated. To the refiner, a copper casting, no matter how made, is known as a "shape," irrespective of whether it is wire bar, ingot, cake, slab, billet, etc. As practically all shapes are cast in an open mold, that is a mold without cope, the surface of the shape cools in contact with the atmosphere and has a coating of oxide. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. When copper is to be rolled into thin sheets or drawn into very fine wire, the slightest physical defect becomes evident. It is, therefore, of the utmost importance to consider every characteristic of the shape and ascertain the physical and chemical relationship. Pitch and Set.—The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface of the shape (which may vary from a concave to a convex); and the '" set,"' or the detail appearance of the surface of the shape (the wave-like structure). When the shape presents a concave surface, it is known as "low pitch;" a convex surface is known as "high pitch" or "tough pitch;" and a level surface is called "flat pitch." The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are

Jan 1, 1921

By William P. Blake

At the August meeting of the Geological Society of America, I presented a paper on the occurrence of alunogen and bauxite upon the Upper Gila river, about 40 miles north from Silver City, New Mexico, together with observations upon the geology of that region." Inasmuch as the subject is specially interesting to metallurgists and mining engineers, and as our Transactions contain recent important papers, by Dr. Hayes, M. Laur, of France and others, upon bauxite, I venture to offer to the Institute, in more condensed form, an account of the deposits described in the paper above referred to. The only other published account of the alunogen locality which I have been able to find is a prospectus-pamphlet, issued in a small

Jan 1, 1895

By M. H. Loveman

THE orebody described below has been rediscovered and developed within the last 3 years. It has, however, been known and worked by the Chinese for hundreds of years. When assay values and size are considered, it contains what is probably one of the largest single bodies of zinc and lead sulphides yet found. The tonnages developed at other places, as at Broken Hill, are much greater but the average zinc and lead sulphide contents are considerably lower than at Bawdwin. Bawdwin is situated in the semi-independent State of Tawng Peng, one of the numerous units which make up the Northern Shan States. These States are under British rule and are generally considered as a portion of Burma. They are governed as a separate administrative unit, however, under the Lieutenant Governor of Burma. Each State is under its own chief, or Sawbwa, who has considerable power over his own subjects. Bawdwin is approximately in latitude N 23°6', longitude E 97°20', about 50 miles south of the nearest point on the Chinese border and 450 miles north of Rangoon (Fig. 1). The period at which mining was first begun at Bawdwin is unknown. The most reliable records have been obtained by deciphering local Chinese inscriptions and from these it is concluded that the work dates back to at least the beginning of the 15th century. The first undoubted reference to the mines by a European is by Symes in 1795. Crawford in 1827 estimated the output of silver from the mines at $600,000 annually. At about the middle of the 19th century the rebellion of the Chinese Mohammedans in the neighboring Chinese province of Yunnan so weakened the power of the Chinese that the incursions of hostile tribes (Kachins) made work extremely dangerous. The mines were finally abandoned by the Chinese about 1868. The closing down of the mines was probably not entirely due to outside causes but may have been influenced somewhat by the increasing difficulty of handling the water, as the workings gradually descended below the water level of the district. Several attempts were made by the Burmese kings, Mindon Min and Thebaw, to resume operations, but because of a

Jan 12, 1916

By N. B. Davis

I . INTRODUCTION WHILE working with a number of very sticky cracking clays from western Canada the writer became interested in a study of the cause of the excessive plasticity, This led to a review of the rather bulky literature on the subject and the finding that plasticity still remains to be satisfactorily explained. Most of these investigations seem to have been carried on solely from the chemical viewpoint, the geologic aspects having been ignored. In nearly every case, the investigators have worked with the higher-grade clays of low to medium plasticity, such as the kaolins, the excessively plastic ones having generally been neglected, partly because of their limited application, yet the author believes that these are

Jan 2, 1915

The Alligator Ridge Project is owned jointly by Amselco Minerals Inc. and Occidental Minerals, with Amselco being the operator. It is the latest of Nevada' s gold heap leaching operations , having gone into operation in October of 1980 after a design and construction period of only seven and one-half months. Alligator Ridge is located about 77 km (48 miles) northwest of Ely, Nevada. Three separate but adjacent ore bodies will be mined: Vantage I, II and III. The first lies virtually at the surface and is totally oxidized; the second is somewhat deeper and contains some carbonaceous material; and the third is at the lowest horizon and contains substantial carbonaceous ore. The ore is a Carlin- type siltstone which has been silicified, especially at depth, and contains finely disseminated free gold. Exploration drilling on Alligator Ridge resulted in the defining of an ore reserve of about 4.54 million mt (5 million st) averaging 4. 12 g Au per mt (0. 12 oz Au per st). A pilot heap leaching program was run during 1979. Because of the high content of fine material in portions of the ore body, one test heap of 5,000 tons was leached, after being crushed to 19 mm (314 in.), in the conventional manner using cyanide and caustic while a second heap of 2,500 tons of ore was agglomerated with cement before leaching. Results of this work were reported at the 1980 American Mining Congress meeting by Paul Chamberlin (see Bibliography). The test work clearly indicated the superior leaching qualities of the agglomerated ore, and the plant was designed on this basis. Run-of-mine ore is crushed in an open-air crushing plant using a jaw crusher followed by two cone crushers, one standard and one shorthead. Provision was made to bypass the shorthead when the ore is wet from rain or snow. Crushed ore at 19 mm (314 in.) size is mixed with cyanide solution and cement, with the ratio of the latter to the ore being 2 to 5 kg per mt (4 to 10 lb per st). The resulting moisture content is about 870, and the fines are effectively bound to the coarse particles so that migration of the fines in the heap does not take place during leaching. For agglomeration, Amselco uses a rotating drum 2. 75 m 0 by 6 m long (9 ft 6 by 20 ft). For the same agglomeration, Candelaria uses three "grasshopper" conveyors, with introduction of caustic- cyanide solution at the conveyor transfer points. Provision was made for future addition of cement slurry at these same points.

Jan 1, 1981

The following is an incomplete list of members and guests who called at Institute headquarters during. the period Mar. 10, 1919,. to Apr. 10, 1919. F. T. Agthe, Hannibal, Mo. Jay Lonergan,. Denver, Colo. W. F. Almy, Canada. R. R. London, Cebu, P. I. P. G. Bandy, Mexico. W. D. Mainwaring, Philadelphia, Pa. H. R. Bank, Humboldt, Ariz. _ W. G. Mitchell, Montreal, Can. Alan M. Bateman, New Haven, Conn. Francis Nicholson, Joplin, Mo. C. A. Brooks, Lead, S. Dak: C. H. Palmer, Los Angeles, Calif. Louis J. Brunel, Oakland, Calif. D. A. Powell, Columbus, Ohio. W. Burns, Sante Fe, N. M. W. H. Reber, Dallas, Tex. J. B. Carlock, Major, 1st Gas Regt. Capt. J. B. Richards, Spokane, Wash. Louis S. Cates, Hayden, Ariz. T. C. Roberts, E. Orange, N. J. W. M. Corse, Mansfield, Ohio Max Roesler, Washington, D. C. E. 0. Daue, Philadelphia, Pa. C. 0. Sanford, Los-Angeles, Calif. John Davenport, W. Norfolk, Va. Gustave Sessinghaus, Denver, Colo. James T. Dixon, London, England, . E. H. Shriver, Milford Center, Ohio. S. K. Dahl, Messina, Transvaal, S. Af. H. M. Spoor. W. G. Eberhardt, Tucson, Ariz. W. H. Staver, New York. H. S. Emlaw, Grant Haven, Mich. D. B. Sterrett, Washington, D. C. I. W. Farrand, Camp Merritt. W. G. Swart, Duluth, Minn. Oscar Gotsch, Jr., St. Louis, Mo. A. W. Stickney, London, England. James 0. Greenan, Oakland, Calif. E. C. Templeton, Downey, Calif. Gilbert Hart, Philadelphia, Pa. . . R. T. Walker, Pioche, Nev. K. L. Hsueh, China. A. T. Ward, Bellefonte, Pa. Zay Jeffries, Cleveland, Ohio. Joel H. Watkins, Washington, D. C. R. W. Kern, Verde, Ariz. J. Wertheimer, Cleveland, Ohio. H. D..Kinney, Easton, Pa. C. R. Wilfley, Ouray, Colo. E. L. Lasier, Washington, D. C. J. P. Wood, Engrs., U. S. A. Carl Zapffe, Brainerd, Minn. Leland D. Adams has left the employ of the Weedon Mining Co., Ltd., at Montreal, Quebec, and is going to Oakland, Calif., where his address will be 1180 Mandana Boulevard.

Jan 5, 1919

By A. E. J. Engel

The New York talc deposits of commercial importance are in St. Lawrence and Lewis counties, in the northwest Adirondack Mountains (Fig 1). All of the deposits are of pre-Cambrian age and occur within highly deformed and recrystallized marble of the Gren-ville series. The deposits in St. Lawrence County, near Gouverneur, are the largest and most productive of their type known in the Western Hemisphere. In 1948 the seven mines which are in operation will produce about 130,000 tons of ground talc. All talc production in Lewis County is from one mine. There the annual production ranges from 15,000 to 30,000 tons. These so called talcs of New Yorb State include earth materials of different chemical and mineral compositions. In general the mineral talc is subordinate in amount to other minerals in both the Gouverneur and Natural Bridge deposits. In the Gouverneur district the mineral talc comprises less than 25 pct of the mined and ground rock. Most of the rock mined is a tremolite- or tremolite-anthophyllite schist somewhat altered to serpentine and talc. This characteristic in no way tlevaluates the "talc" for certain markets, and in some instances makes the material more desirable. The Natural Bridge talcs include types high in serpentine, as well as complex aggregates of serpentine, talc, carbonates, and diopside. Usage of the term talc, however, for

Jan 1, 1950