Search Documents

By Alan T. Gorton, T. L. Joseph, Gust Bitsianes

High-temperature X-ray diffraction techniques were used to determine thermal expansion coefficients of iron and its oxides. Lattice parameters of a and iron, wiistite, magnetite, hematite, and goethite were determined and plotted as a function of temperature. From these results, the true and mean linear thermal expansion coefficients were calculated. In the case of noncubic crystals, the expansion coefficients were determined along each of the crystallographic axes. The effect of the magnetic transformation on lattice parameter was measured for a iron and magnetite at their respective curie temperatures. COEFFICIENTS of expansion for iron and its oxides were determined from the temperature dependence of their lattice parameters. From these data, the true linear coefficients were derived by means of the formula: at =[(l/ao )(dao/dt)] [1] where at is the true linear coefficient of expansion, a, is the lattice parameter in angstrom units, and all variables are referred to the temperature, t, in OC. Thus the true expansion coefficient represents the instantaneous change in lattice parameter on a unit basis and at a particular temperature. A second expansion coefficient is also often used. It is termed the mean linear coefficient and is defined in the following way: am = [ao(t) - ao(O)]/ao(0) l [21 This coefficient represents the average change in lattice parameter on a unit basis but at a specified parameter length, ao at O°C, and over a specified temperature range,1 to 0°C. Generally the true co-

Jan 1, 1965

By Charles H. Behre

SLATE (Thonschiefer, German; ardoise, French) is a rock, an aggregation of mineral grains, occurring in nature, which is used for roofing and other special purposes. It is finely granular and crystalline and generally derived from an originally clayey bed or series of beds. As a result of its having been put under essentially horizontal compression by geologic forces, this material now has its particles elongated and flattened so as to yield a very good rock cleavage along the flat surfaces of the minerals, a feature entirely independent of the original bedding in the rock. This is the gist of the definition adopted by the Committee on Slate of the American Society for Testing Materials. Slate differs in varying degrees from most other common rocks (such as limestone, sandstone, granite, and "trap") in chemical and mineral composition. Its most characteristic feature, however, is its tendency to fracture along a series of very nearly parallel and very closely spaced smooth planes, called cleavage planes. This property of cleaving, above all else, gives slate its industrial value. ORIGIN AND MODE OF OCCURRENCE Most of the features of slate might be anticipated from its origin. Being a rock rather than a mineral, its composition may vary consider- ably without impairment of value. In most slates, the material of which the rock is now composed was once deposited as clay on the bottom of a lake or sea. Subsequently these clayey strata were compressed by the kind of lateral pressure that folds rock strata, the minerals of the clay being changed or metamorphosed. In the chemical reaction involved, new and essentially plane-shaped minerals belonging to the mica groups were developed. Other minerals were formed but micas generally pre- dominated. These were oriented so that their two longer dimensions are approximately at right angles to the last effective direction of pressure. Since the crystals are thus subparallel, fractures can be developed easily along their surfaces, much as cards can be separated by inserting a knife blade between them. For the foregoing reasons, slate is found in noteworthy amounts

Jan 1, 1949

By C. A. Stetefeldt

Jan 1, 1895

By A. Gemperle

Electron diffraction and transmission electron microscopy on foils at room temperature were used to investigate the ordering of Fe-Si alloys containing 10 to 23 at. pct Si. A certain degree of DO3 order was found in all alloys. With the exception of the lowest silicon concentration for which the antiphase domains could not be clearly resolved, the alloys have a domain structure of two-domain type with boundaries having 1/4a01<111> displacement vectors for less than 12.3 at. pct Si and with boundaries having 1/2 a0<100> displacement vectors for more than 12.3 at. pct Si. The alloys with 12.3 at. pct Si have a domain structure consisting of fine domains with 1/2a&apos;o<100> boundaries within much larger domains with 1/4a&apos;o<111> boundaries. The development of these structures can be explained by transition of the alloy from the disordered state into the B2-type order and then into the D03-type order by the mechanism proposed previously for the FeSAl alloys. The existence of the B2 structure in the lower part of the investigated concentration range reported in some articles can be explained by fine domains with 1/2a&apos;o<100> boundaries formed by several disordered planes within large domains with 1/4a&apos;o<111> boundaries. The ordered structure predicted by the theory —with practically no domain boundaries —is found in the alloys having 12.3 at. pct Si where it develops in the B2 structure region. ORDERING in Fe-Si alloys was first studied by phragmenl who found that beginning with 13 at. pct Si the DO3 (Fe3Si) superlattice reflections appear in the diffraction patterns. The equilibrium diagrams constructed later by corson2 and Haughton3 from various measurements proposed the existence of a homogeneous solid solution (a phase) in the range from 0 to 25 at. pct Si. Jette and Greiner4 and Farquhar et al.5 measured the relation between lattice parameter and composition and they considered the break in the curve at 9 to 10 at. pct Si to be caused by the ordered solution a"(Fe3Si). Glaser and Ivanick6 Determined critical ordering temperatures of the alloys containing from 10.9 to 27.9 at. pct Si from the measurement of the electric resistivity of quenched samples. In all cases the critical temperature was lower than the melting point and it was highest for 25 at. pct Si. Lihl and Ebel7 measured the lattice parameter curves at various temperatures up to 1000°C. The region between two breaks on these curves, corresponding to 10 to 12.5 at. pct Si at room temperature, was considered by them to be two-phase (a + a"). They concluded by extrapolation of the measured values that a" in the alloy having 25 at. pct Si is stable up to the melting point. Davies8 studied superlattice reflections in the X-ray diffraction patterns of an alloy containing 8.7 at. pct Si. He found the B2 structure and short-range order in the slowly cooled samples and the DO3 A. GEMPERLE is Research Scientist, Institute of PhysicS, Czechoslovak Academy of Sciences, Prague, Czechoslovakia. __Manuscript submitted January 2, 1968. IMD structure in the quenched and annealed samples. This investigation first reports the presence of the B2 structure, phase a&apos;: in Fe-Si alloys. Meinhardt and krisement9,10 also found its existence in Fe-Si alloys by neutron diffraction. No order was detected by them in the alloy containing 8 at. pct Si. The onset of B2 order was observed at a composition of 9.2 at. pct Si. They found almost perfect B2-type order with partial DO3-type order at room temperature in the 10 to 12.5 at. pct Si range and almost perfect DO3-type order in the 12.5 to 25 at. pct Si range. They established the critical temperatures Tc of both the structures through measurement at higher temperatures. The critical temperature for the B2 structure was found to be always higher than the critical temperature for the DO3 structure of the same alloy. They extrapolated the curves of the critical temperatures and concluded that the alloys with more than 17 at. pct Si have the B2 structure up to the melting point and the alloys with more than 23 at. pct Si have the DO3 structure up to the melting point. The results of Meinhardt and krisement9,10 were confirmed by Dokken&apos;s measurement" of the temperature dependence of the electrical resistivity in the 10.8 to 15 at. pct Si range. On the other hand chessin12 detected by X-ray diffraction a considerably lower degree of order in the 12.7 at. pct Si alloy. ANTIPHASE DOMAIN STRUCTURE IN ALLOYS WITH B2- AND DO$-TYPE ORDER The ordered structures B2 and DO3 can be described in terms of a subdivision of the bcc lattice into four fcc sublattices with a parameter double that of the bcc lattice. Following Marcinkowski13 we will label them I. 11, 111, IV. The B2 structure in the AB alloy is formed by placing A atoms on sublattices I and II and B atoms on sublattices III and IV. In a non-stoichiometric perfectly ordered alloy having concentration (A) > (B), A atoms occupy sublattices I and 11. and A and B atoms distributed at random occupy sublattices III and IV. The DO3 structure in an A3B alloy is formed by placing A atoms on sublattices I, 11, and 111, and B atoms on sublattice IV. In a nonstoichiometric, perfectly ordered alloy having concentration (A)/3 > (B), A atoms occupy sublattices I, 11, and 111, and A and B atoms distributed at random occupy sublattice IV. As further shown in Ref. 13, two types of domains are possible in the B2 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4 a&apos;o<ll1> only. Four types of domains are possible in the DO3 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4a&apos;o<111> and 1/2a&apos;o<l00>. Bethe14 suggested on the basis of theoretical considerations that in a structure with two sublattices at low temperatures only one domain should be present in the whole crystal at equilibrium. Similarly Bragg15 concluded that at low temperatures the domain struc-

Jan 1, 1969

The following officers and committee chairmen were elected: Honorary Chairman, Herbert Hoover; Chairman, Elmer A. Sperry, New York; Vice-Chairman and Chair-man of the Executive Committee, John W. Lieb, New York; Vice-Chairman, C. E. Grunsky (Pacific Coast), San Francisco; C. F. Kettering (Middle West), Detroit; Execu-tive Secretary, Maurice Holland; Executive Committee: Gano Dunn, George W. Fuller, Maurice Holland, Frank B. Jewett, John W. Lieb, H. J. McGraw, Calvin W. Rice, W. E. Wickenden, all of New York; Dugald C. Jackson, Cambridge, Mass.; 0. C. Merrill, Washington, D. C.; Charles F. Scott, New Haven, Conn.; Elmer A. Sperry, Brooklyn, N. Y.; Finance Committee. John W. Lieb; Technical Program Committee: D. C. Jackson; Transporta-tion Committee: F. B. Jewett; Entertainment Committee: 0. C. Merrill; Publicity: J. H. McGraw; Promotion and Attendance: George W. Fuller.

Jan 5, 1928

By K. Huessener

In presenting the following data on combustion in the open hearth furnace and the advisability of automatic combusion control, the author finds himself much more severely handicapped by the lack of reliable test results than he had anticipated when he first undertook to write this paper. In order thoroughly to investigate how the results of an open-hearth furnace are influenced by combustion, one would have to draw up a large number of heat-balance sheets, as Kinney and McDermottl have given for one heat in their extremely able paper on "Open Hearth Efficiency,&apos; presented before the American Iron and Steel Institute on October 27th,1 1922. Instead of covering only one heat, however, such heat-balance sheets would have to embrace a large number of heats, and not only for one kind of fuel, but for all the various fuels in customary use. Use of Radiation-protected Pyrometer Such tests necessitate extremely careful temperature readings, and here the first serious difficulty presents itself. Nearly all the temperature readings so far published have been taken with thermocouples for the lower ranges and with optical or radiation pyrometers for the higher ranges. This method of measuring reveals the temperature of the surrounding walls, or in the case of optical or radiation measurements, the temperature of that part of the opposing walls which has been focused by the instrument. The error in ascertaining the temperature of the gases entering or the waste gases leaving the checker chambers is probably not very large, as the flowing gases impart their temperature to the walls of the flues. On the other hand, the uptakes, where the preheat temperature of gas and air are usually measured, are under the influence of radiated heat from the port ends, and correct temperature readings can here be taken only by using a radiation-protected pyrometer of the aspirating type.

Jan 1, 1926

By Paul Berggreen

LIST OF PUBLICATIONS In the Bibliography titles of publications are replaced by corresponding symbols in this list. American A-1. Transactions of the American Institute of Mining Engineers, New York. A-2. Journal of the New York Microscopical Society, New York. A-3. Journal of the Franklin Institute, Philadelphia, Pa. A-4. The Metallographist, Boston, Mass. A-5. The Electrochemical and Metallurgical Industry, New York. A-6. Bulletin of the American Institute of Mining Engineers, New York. A-7. The Iron Trade Review, Cleveland, Ohio. A-8. The Journal of Physical Chemistry, Ithaca, N. Y. A-9. The Physical Review, New York. A-10. Van Nostrand&apos;s Electric Engineering Magazine, New York. English E-1. Proceedings of the Institution of Mechanical Engineers, London. E-2. Journal of the Iron and Steel Institute, London. E3. Proceedings of the Institution of Civil Engineers, London. E-4. Journal of the Chemical Society of London, London. E-5. Philosophical Magazine, London. E-6. Proceedings of the Royal Society of Edinburgh, Edinburgh., E7. Carnegie Scholarship Memoirs, London. E-8. Proceedings of the Royal Society of London, London. E-9. Chemical News, London. E-10. Philosophical Transactions of the Royal Society of London,, London. E-11. Transactions of the North-East Coast Institution of Engineers and Shipbuilders, Newcastle-on-Tyne E-12. Iron, London. E-13. Nature, London. E14. English Mechanic and World of Science, London.

Jan 6, 1914

By R. B. Full

DURING the summer of 1949, the United Nations Scientific Conference on the Conservation and Utilization of Resources met at Lake Success. As summed up by one writer, the purpose was: "That everyone will try to learn how to feed more people from an acre of land." That objective is a stimulus to the phosphate rock industry as well as other industries. Phosphate rock was mined first in the Canadian province of Quebec where it was found as an apatite in pockets. In 1863, mining began near the Rideau Canal, first in open trenches and quarries until shafts were sunk. These operations were difficult since hard rock had to be drilled and blasted. Steam was the source of power. The phosphate rock was hand-selected and recovery ranged from 6 to 10 pct, averaging 70 pct to 85 pct bpl (bone phosphate of lime). Costs, f.O.b. Montreal, were $14 a ton, and selling prices averaged $17 a ton. In 1885, about 29,-000 tons were sold on this basis, but by 1892 the output fell to 8000 tons at an average price of $15 a ton at Montreal. South Carolina Deposits Phosphate rock was first discovered in South Carolina in 1837, but a mining company was not formed until 1867. It was immediately successful, and the industry continued to develop and ship an increased tonnage of land and river rock, shipments increasing from approximately 20,000 tons in 1868 to 537,000 tons in 1890, when the shipments began to decrease. In 1892 only 350,000 tons were shipped. In this field there were two types of deposits: land rock and river rock. More land rock tonnage was mined until about 1887 when river rock production began to equal it. The land rock was mined adjacent to and in the river marshes by pick, shovel, and wheelbarrow. Each worker dug daily a space 6 ft wide, 15 ft long and 6 ft deep, which was overburden, and then loaded about 3 cu yd of phosphate rock into wheelbarrows. His helper would wheel the barrows to small steam railroads up to 250 ft distant. Water was kept from the pits by steam pumps connected to railway cars. The phosphate rock was loaded into railroad cars, hauled and dumped into a log washer to which water was added, and run over trommel screens to eliminate the clay and loose sand. Steam shovels for loading were introduced about 1891. River rock was mined by floating dipper dredges and at low tide was loaded into barges by laborers using oyster tongs, the large lumps being hand-loaded. Barges and bateaus were unloaded by wheelbarrows which were wheeled to the same type of land rock washers. The washer product was piled with stacked pine cordwood in alternate layers and fired for drying. Usually this was done under sheds along the river bank. The dried rock then was transferred to ships, usually three or four-masted schooners. Cost of production of both land and river rock, including $1 a ton royalty paid to the state for state-owned property, was approximately $4.25 a ton averaging 60 pct bpl. The selling price was approximately $7 a ton f.O.b. In 1886 the courts handed down a decision permitting anyone to mine, and many additional companies were organized immediately. As a result, the selling price was lowered to a profit margin of 50Ø or less per ton. The South Carolina mines were eventually shut down when a more profitable source of phosphate rock was discovered in Florida. Florida Deposits Phosphate rock was discovered in Florida in 1882, and in 1883 a small quarry was opened near Hawthorne. In 1886 phosphate rock of good grade was discovered on Peace River, and the Arcadia Phosphate Co. was formed. In 1888 the company began shipments amounting to 3000 tons that year. During the latter part of 1888, hard-rock phosphate was discovered near Dunnellon. Exploration extended rapidly, and deposits of hard-rock phosphate were mined over a wide area so that shortly after 1900

Jan 1, 1952

The Carlin gold deposit is located in northeastern Nevada about thirty-five miles by road from the town of Elko. Following the staking of six square miles &apos;of ground, a drilling program outlined a fine ore body mineable by open pitting. The resulting mine turned out to be the largest open-pit gold operation in the world, until the Rosario Pueblo Viejo operation was started in 1975. Because of the high profitability forecast at the then $35 gold price, construction of a 2000 stpd mill was commenced on a crash program and was completed for Newmont Mining Corporation by Bechtel Corporation in ten months. Production was started in early 1965. The gold mineralization occurs in marine-type sediments, chiefly silt- stones and limey shales, and the ore characteristics make for a difficult materials-handling problem. At 5% to 6% moisture the ore is dusty during crushing, but even a light rain or snowfall virtually turns the material into a slurry. Crushing this sticky ore below 314 in. (19 mm) in the dry season and 1 in. (25.4 m) during the winter is extremely difficult and leads to problems with conveyors, chutes, and fine ore storage. The initial flowsheet for Carlin&apos;s crushing plant used a 5 ft by 22 ft (1.52 m by 6. 7 m) vibrating feeder -grizzly under the 60 -ton dump pocket for feeding the 42 in. by 48 in. (1067 mm by 1220 mm) single toggle jaw crusher and a 5 ½ ft (1.52 m) standard cone crusher in closed circuit with a 6 ft by 12 ft (1.83 m by 3.66 m) vibrating double - deck screen. Because continual packing of fines in the vibrating feeder pan would cause frequent plant shut-downs to remove the fines with jack hammers, the decision was made to replace the vibrating unit with an apron feeder and stationary grizzly ahead of the jaw crusher. A dribble belt was also installed under the apron feeder. This installation has greatly improved the feeding of the pit run ore to the .primary jaw crusher. Mining at Carlin is done by a 5 yd shovel and 7 ½ and 10 yd front-end loaders, and ore transport is by several sizes of trucks from 30 to 75 tons capacity. These pit haulage trucks dump onto stockpiles adjacent to the primary crusher. Ore is then fed to the dump hopper by front- end loaders only when the crushing plant is operating. This extra handling procedure is necessary because plant delays caused by problems with wet ore in the secondary crusher resulted in the ore setting up or packing in the dump pocket. Solidified material in the dump pocket would in turn delay truck haulage. The substitution of an

Jan 1, 1978

By Thomas E. Howard

Scientific research in mining has a comparatively short history. So long as it was possible to maintain adequate mineral supplies by long-established methods, there was little need for the scientific approach. That the end of this comfortable situation is at hand is evinced by the variety and rapidly growing amount of mining research in progress all over the world. The pattern of development of mining research in other countries shows that it started only after a problem became critical. Therefore, the work generally has been short range and usually concentrated on a specific problem. An example is the preoccupation in western Europe with the problem of strata control.

Jan 1, 1962

By C. J. Barber

This paper Donald describes how New Jersey Zinc Co. made surveys for a connection between the Ivanhoe and Van Mater shafts at Austinville, Va. Except to say that the two faces had to meet "accurately" on line and grade, Donald does not indicate the required precision. Assuming that there were 24 angles in the 1 ½ -mile traverse and 15 in the one-mile traverse, it can be shown that if the average error in plumbing each shaft was ±30" and the average error in measuring each traverse angle was ±10", then the average error at the point of connection would have been about ±1.9 ft normal to the line between the shafts. This calculation assumes that any errors in the triangulation would be negligible compared with the errors in the plumbings and traverses, and it also neglects taping errors. With no constant errors or blunders, the latter would be important only in lines normal to the line between the shafts.

Jan 7, 1959

It is always the case with heavy and cheap materials that the area within which they can be economically used depends upon the cost of transportation, and in those days of poor roads and no mechanical means of haulage on them, coal could only be moved a few miles from the mine by any other means than water. The need of better means of transport to the areas west of the mountains had been urged by Washington and many other leaders, but the first turnpike over the Alleghenies only reached the Ohio River at Wheeling, W. Va. in 1818. The James River and Kanawha road reached the Ohio in 1831, that from Winchester, Va. to Parkersburg in 1838, and the road through the Cumberland Gap was completed in 1797. None of these affected the coal industry excepting indirectly by building up some of the river towns which coal could reach. The inadequacy of roads alone to carry the traffic of the rapidly growing interior communities was demonstrated only a few years after the National Pike was completed, and in the early 1820&apos;s several of the states embarked upon the construction of a canal system, which had been under discussion for some years. The Erie Canal was opened in 1825 from Lake Erie to the Hudson River through New York; Pennsylvania, Virginia and Maryland had already started similar projects designed to bring traffic to their principal cities from the interior. The Pennsylvania Canal was started from Columbia, as a railroad extended from Philadelphia to that point, and it followed the Susquehanna and Juniata Rivers to Hollidaysburg; thence to Johnstown, a distance of 36 miles, where it consisted of partly railroad and partly inclined planes, the boats being hauled up, and lowered down the planes; from Johnstown the canal followed the Conemaugh, Kiskiminitas and Allegheny Rivers to Pittsburgh, 104 miles. Boats first reached Pittsburgh by this route in 1834. The Chesapeake and Potomac Canal followed the Potomac River from a point above Alexandria above the falls, to Cumberland. This canal was chartered in the eighteenth century and a portion of it was used by traffic in 1800. It was too small to be of much use and was abandoned, and later after many legal and financial vicissitudes was completed to Cumberland, traffic from there starting late in 1850. This date, however, was long after the Baltimore and Ohio Railroad had been completed to

Jan 1, 1942

AMERICAN INSTITUTE OF MINING ENGINEERS 29 West 39th Street, New York, N. Y. PROPOSAL FOR MEMBERSHIP Mr.. Address Member is hereby proposed by the undersigned, as a Associate Junior Member .of the American Institute of Mining Engineers. Signatures of three Members or Associates. Place of birth, Year of birth_ Education, when, where and how acquired, with degrees, if any. A technical education is not requisite for membership. Data Please give record of experience on following page with dates; for example, in the form used by "Who&apos;s Who In America" and similar publications.

Jan 10, 1917

By Ralph Hultgren, David W. Mitchell

Magnesium alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600" to r 7o0°F.; the casting temperature, which depends upon the mold shape, is usually 200° to 300°F. lower. The process of superhcating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported1 that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results? As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted&apos; project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. Materials and Methods The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesiun used in these alloys was of both carbothermic3 and electrolytic&apos; origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200° to 1250°F., portions of approximately one pound each, were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21 † covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F. for 15 min., then . cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By W. H., Bassett

IN January, 1926, the writer began a study of the commercial value of beryllium in its relation to copper. The purpose of the investigation was not to make a mere laboratory study of the characteristics of beryllium-copper alloys, but to determine under mill conditions the behavior of copper when alloyed with beryllium and when other metals were added to such alloys; in other words, it was considered important to know whether the alloy bars could be hot-rolled or cold-worked, and what limits in composition would have to be established for these two methods of working. Consequently, more stress has been placed on the practical application of the alloys in engineering and commercial use than on a discussion of the metallography of the specimens examined, although this part of the matter has not been entirely neglected. Credit should be first given to G. Oesterheld,1 who, in 1916, published the copper-beryllium equilibrium diagram. Fig. 1 has been copied from the original article with the simple substitution of English words. It will be noted from Fig. 1 that alpha solid solutions are formed, up to about 1.5 per cent. Be (10.5 atom.). The freezing-point curve, after falling from 4.2 per cent. Be (23.5 atom.), enters into a very complicated form over the entire beta region. There is a possible compound, Cu2Be, at about 6.5 per cent. Be (32.3 atom.). The pure gamma range extends from 11.2 to 12.2 per cent. Be. (46.5 to 49 atom.), after which the liquidus rises rapidly to 30 per cent. Be. (75 atom.). The delta solution extends from 25 per cent. to an unknown percentage of beryllium. There is a eutectoid point at 575" C., extending from 1.5 to 11.2 per cent. Be., the maximum time interval of which occurs at 6 per cent. Be. Below this line the beta solution is described as breaking up into alpha and gamma. Microscopically, the eutectiferous alloy thus formed closely resembles pearlite, and requires a high magnification for its resolution.

Jan 1, 1927

By K. G. Wikle, W. W. Beaver

The factors which control the rate of dissolution of pure gold in cyanide solution were studied both directly and through measurement of solution the current-potential curves for the anodic and cathodic portions of the reaction. The mechanism of dissolution is probably electrochemical the reaction in nature, and the rate is determined by the rate of diffusion of dissolved oxygen or cyanide to the gold surface, depending on their relative concentrations. The significance of the results and the effects of impurities are considered. ALTHOUGH the dissolution of gold in aerated cyanide solutions has been used as an industrial process for treatment of gold ores since the late nineteenth century, the factors which determine the rate of the reaction have never been identified unambiguously. Studies of the rate of dissolution by Maclaurin,1 White,2 Christy,3 Beyers,4 Thompson,6 and others are contradictory in their conclusions; some claiming that diffusion of the reactants to the gold. surface controls the rate, and others that the chemical reaction is inherently slow and related to high activation energy for the reaction. Christy3 and &apos;Thompson" both suggest that the reaction is electrochemical in nature and that the dissolution of gold proceeds at local anodic regions while the oxygen is reduced at cathodic regions on the gold surface. Although their studies are ingenious and do indicate an electrochemical reaction under the conditions of study, their experiments were of limited nature and failed to identify the rate-controlling process in the system. The importance from an industrial viewpoint of a knowledge of the mechanism and rate-controlling factors in gold dissolution can be illustrated as follows: If the rate is controlled by a slow chemical reaction rather than by diffusion of the reactants, then an increased temperature should have a marked accelerating effect; agitation of the slurry should have no effect on rate: and increased concentration of reactants should cause acceleration of the rate. If the rate is controlled by the diffusion of one or the other of the reactants to the gold surface, then increased agitation should increase the rate; increased temperature will increase the rate, but not as much as for the case of a slow chemical reaction; increased concentration of the reactant which is diffusion limited will increase the rate; and the concentration of other reactants should be without effect on the rate. It may be concluded that for design of a commercial process for gold leaching, the rate-controlling factors of the reaction should be understood so that an intelligent choice of the conditions of agitation, temperature, and reactant concentration may be made. The experiments described here lead to the unambiguous conclusion that in a system of pure gold and a pure aerated cyanide solution the rate of dissolution is controlled either by the rate of diffusion of dissolved oxygen or cyanide to the gold surface, depending on the relative concentrations of each. There is also ample, but not conclusive, evidence that the mechanism of the reaction is identical to that of electrochemical corrosion. The practical significance of these conclusions will be discussed later in the paper. Experimental The experimental method used in this work was to employ an electrolytic cell which performed the overall gold-dissolution reaction, and to study the anodic and cathodic reactions of this cell as to their nature and the rate-controlling factors. Simple experiments on the rate of dissolution and the potential of the dissolving specimen also were performed under conditions of agitation, temperature, and concentration identical to those used in the electrode studies. Analysis of the electrode studies by well established theories of electrochemical corrosion were made, and the results were found to bear a one-to-one relation with actual rate and potential measurements. Electrode Studies: The Anodic Reaction: The gold specimen used for all of the electrode studies and the rate determination consisted of a sheet of 99.99 + pct Au wrapped around a lucite rod and sealed at the edges with plastic cement, thus forming a cylinder of gold of known and constant area (8.0 sq cm). The lucite rod was threaded into a brass spindle which could be rotated at speeds of 100, 300, and 500 rpm. For the electrode studies electrical contact between the gold cylinder and the brass spindle was made by means of a gold strip covered with plastic. The anodic dissolution of gold was studied by immersing the electrode in a solution containing known concentrations of KCN and KAu(CN)2 but free of oxygen, and by passing an anodic current through the gold electrode. The pH of the solution was maintained between 10.5 to 11.0 in these and all other tests by addition of KOH. The pH was measured before and after each test by means of a glass-elec-

Jan 1, 1955

By Henry Faul

MEASUREMENT of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (I) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quantitative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carnotite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement.

Jan 1, 1947

By A. V. Pegler

As with most rheologically defined materials, rocks react differently in different environments to similar forces. Physical changes and deformations depend as much on the rate of change of stress as the magnitude of stress. In many instances the rate of change is more important. Under load, all real materials will flow if given time. If there is no time for flow, materials tend to react in a brittle manner. Particular characteristics are developed in rocks during their periods of formation and postformative geologic history. Whatever their mode of occurrence, rocks are a record of their formation and changes. Where analyses are possible, advantage should be taken of the natural inherent characteristics to help design economical functional structures. A number of techniques of measurement and analysis have been developed. The fracturing of rock by hydraulic pressure has been examined by many authorities but few within the scope of available published literature have used the actual rocks concerned in tests to examine directional characteristics or preferred strain propagation rates and directions. In a number of investigations of the properties of rocks for mine design purposes and stress analysis problems in which the writer has been associated, it has been demonstrated that there are definable preferred shear planes in most rocks. Preferred shear planes can be identified by a photoelastic method of analysis, and the information can be used to improve design of optimum drilling and breaking directions for mining purposes. Definable principal strain directions can be determined to facilitate design directions of optimum stability for permanent mine openings. In field fracturing operations the same directional characteristics as outlined above should be used to define preferred fracturing directions as in the laboratory from oriented samples. It is mainly with this aim that

Jan 1, 1968

By Stanley Gill

The apparatus is composed of sections of small diameter, seamless steel tubing welded into a continuous flexible tube. At the bottom end a 1/4-in. pipe nipple with a 10 to 15-lb. weight is attached, together with a registering thermometer and a pair of ball check valves. The entire length of tubing is coiled in a single layer upon a drum 4 ft. in diameter which can be attached to the platform of a truck and provided with devices for winding and unwinding the tubing. Connections are made with the upper end of the tubing through a stuffing box, thence to a gas manifold to which a pressure gage is connected. Hydrogen gas is carried in standard 2-ft. cylinders and readings are taken by admitting gas into the tubing from one (or both) of the hydrogen cylinders until the pressure has been built up above that to be measured. At this time the gas supply is cut off. Excess gas escapes through the open end of the tubing and when equilibrium is reached, the pressure is read at the surface gage. Corrections are made for the weight of the column of gas. The advantages claimed for the apparatus include accuracy and the ability to measure the pressures at any number of points without removing the gage. Among the disadvantages of the apparatus are the somewhat bulky size of the equipment and its relatively high initial cost.

Jan 1, 1933

By Michael Chender

The current outlook for financing new copper production is not very encouraging. At a time when companies are slogging through a protracted period of low prices as well as having to accept lower profits due to more stringent tax and royalty schedules, banks are beginning to require companies to take a greater equity interest in new projects. Mineral resource financing, including copper, seems to have lost much of its appeal to the lending institutions, and loans of any kind to many of the developing countries -from which over half of new copper capacity could be expected to come-are being examined much more critically than they were in the late 1960&apos;s and early 1970&apos;s.

Jan 12, 1976