Search Documents

By H. Sadek

The accompanying table shows the available data pcrtaining to the Hurghada field, the major oil and gas field in Egypt. Operations in Abu Durba, a small field, amounted to almost nothing in 1935.

Jan 1, 1936

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,' it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967

Jan 1, 1921

The Climax design is for the human being and his needs. Climax President Arthur Bunker has likened the high mountain operation to a giant, 250 million tons in weight, and 12 thousand feet high. No matter how huge or complicated the plant, the design must assure efficient operation by its human operators. By the same token, living and playing facilities must be designed for fullest satisfaction in use-else the capital investment is not justified. Even the product, molybdenum, finds its application through the ever growing demands of a highly industrialized society of humans. Research in Climax Laboratories, in tune with our technical age, helps guide molybdenum to its maximum use for society.

Aug 1, 1955

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

IN spite of considerable study,1-5 the nature of slime coatings in flotation is still not completely understood. However, phenomena that control flocculation and dispersion of colloidal systems are now interpreted in terms of electrical double layers."' Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed, flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which electrokinetic data are available.8-12 Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple.

Jan 7, 1958

By D. R. George, J. R. Ross, J. D. Prater

In the United States nearly 200,000 tons of copper per year are being produced, by leaching waste rock and oxidized copper ore with dilute sulfuric acid-ferric sulfate solutions and precipitating the copper on scrap iron. The flow of solutions is in excess of 80 million gpd. A survey conducted by the U.S. Bureau of Mines in late 1965 at 14 mines in Arizona, Utah and Nevada, showed that with a few exceptions, the solutions contain from two to a maximum of 15 ppm U3O8, and there is strong evidence that these represent equilibrium concentration and not merely an accumulated in-process inventory resulting from recycling the solutions for many years. Consequently, it is believed that uranium could be recovered at a constant rate as long as mining and leaching operations continue. Preliminary surveys and estimates by the USBM indicate a production potential of possibly 1000 tons of U3O8 per year at a cost of less than $8 per lb if the major process streams from most of the large copper mines in the western United States were to be treated. Laboratory research by the USBM showed that the uranium could be efficiently recovered as a specification-grade uranium concentrate by a combination of ion exchange resin and solvent extraction of liquid ion exchange techniques. A joint pilot plant investigation by Kennecott Copper Corp. and the USBM was conducted on solutions from the Bingham Canyon mine to evaluate a new system of countercurrent ion exchange developed during the laboratory studies. In subsequent small-scale continuous tests, recovery of uranium from the pregnant eluate by solvent extraction and chemical precipitation techniques was investigated.

Jan 1, 1968

By J. W. Goss, M. J. Coolbaugh

A survey of literature published in the U.S. on grouting indicates that most such work has been done to stop water flow in mines and for stabilizing foundations of various man-made structures. Apparently San Manuel is one of the first mines in this country to use grout extensively underground for the strengthening and stabilizing of ground about drifts, shafts, and stations.

Jan 3, 1961

NEW MEMBERS The following list comprises the names of those persons who became members during the period Feb. 10, 1919, to Mar. 10, 1919. ALLEN, ROLLAND CRATEN State Geol., Appraiser of Mines, Lansing, Mich. ALTMAYER, MAURICE ERNEST, Ingenieur des Arts et Manufactures, 145 Rue de la Pompe, Paris, France. AUSTIN, CHARLES L., Assayer, Highland Boy Mine, Utah Cons. Min. Co., Bingham Canyon, Utah. BARTLETT, ARTHUR J., Chief Engr., Louisville Coal & Coke Co. Goodwill, W. Va. BOIES, ORLOW W., Research Chem., Roessler & Hasslacher Chemical Co., 1632 Tenth St., Niagara Falls, N. Y. BRAGG, G. A., Mgr., Experimental Copper Leaching Plant, Mellon Inst. of Industrial Research, Thompson, Nev. BRUSCANTINI, GIOVANNI, Min. Engr., Gen'l Mgr., Sindicato Minero de Cuba, Box 370, Santiago, Cuba. COLONY, R. J Instructor in Geol., Columbia University, New York, N. Y. DAVENPORT, FRANK B., Cons. Engr., 806 Coal Exchange Bldg., WiIkes-Barre, Pa. EATON, S. FORD 120 E. 85th St., New York, N. Y. EBY, J. H., Min. Engr Box 433, Spokane, Wash. ENGELHARDT, EDWARD A., Mgr., Surinaamsche Bauxite Mij, Paramaribo, Dutch Guiana, S. A.

Jan 4, 1919

By J. Chipman, T. P. Floridis

The equilibrium of gaseous H2O-H2, mixtures with liquid iron is used to establish the activity coefficient of dissolved oxygen as log f o = — 0.20 [%O]. Discrepancies in earlier work are explained or eliminated. Additions of cobalt, molybdenum, tungsten, and platinum increase the activity coefficient of oxygen whereas copper and gold decrease it. THE importance of dissolved oxygen as a refining agent in liquid steel has led to a number of studies of its thermodynamic properties. It is the purpose of this paper to examine the effects of a number of alloying elements on the activity of oxygen in the steel bath. As a preliminary to the study of the effects of alloying elements, it seemed desirable to examine certain minor discrepancies in the published data on the properties of oxygen in simple iron-oxygen solutions. The activity and free energy of oxygen in liquid iron were studied by chipman1 in 1933 by means of the reaction h2(g)+-o = H2O (g);K; = PH2O/PH2[% O] [1] The data were in fairly good agreement with calculations from results on the similar reaction CO (g) + O- = CO2 (g); K2 =P CO2/P CO [% O] [2] which had been obtained by Vacher and Hamilton2 as an incidental part of their study of the reaction of carbon with oxygen dissolved in the melt. It was found that the equilibrium ratio k1 was not a true constant but varied with the oxygen concentration in the manner shown in Fig. 1, which is copied from the original paper. This early observation has been refuted in subsequent work but is confirmed in the present paper, and an explanation of the discrepancy can now be presented. In Fig. 1, the two points on the extreme right were disregarded in drawing the

Jan 1, 1959

By W. P. Z. German

Some attention should be given to definitions. The term "unit operation " may have at least two meanings. One meaning is the merging of titles and the development and operation of the unitized area, as if it were one tract of land held under a single oil and gas lease, according to a definite program intended to accomplish a maximum recovery from the pool as a whole at a minimum of cost. It is incomplete when the royalty owners do not also merge their titles to their oil and gas rights in the area, and is complete when they do. The other meaning is not accompanied by any merger of titles, but the development and operation of the area is in accordance, as nearly as reasonably practicable, with such a program. This second conception may be nothing more than a cooperative development and operation plan, but in this paper it is regarded as more than that. If there cannot be unit operation without a merger of titles, it would seem that the state cannot require unit operation, for it cannot require a merging of titles; but if it may consist in requiring each and all of the leaseholders to develop and operate or to submit to a development and operation according to some such common plan as is referred to above without at the same time requiring a merger of titles, it would seem that unit operation may be required by the state. Whether the states have this power is the subject to be herein considered. If the state can so bind the several lessees, it also can so bind the several lessors. The writer does not know what would be an ideal plan for the development and operation of a pool; but it takes into account the fact that the accumulation of gas and oil is not uniform throughout the formation; that often free gas, highly compressed, occupies the upper portions of the reservoir, the oil with compressed gas in solution coming next in order; that at places oil is not overlain by free gas, and sometimes there are peaks where free gas is not immediately underlain by any oil; and the fact that these substances are held under a uniformly distributed pressure, generally referred to as "rock pressure." It also recognizes that the most efficient utilization of this naturally existing reservoir pressure in the recovery of the oil requires that there be no operation of wells completed into areas where gas only has accumulated, for this diminishes the

Jan 1, 1931

By R. B. Fuller

DURING the summer of 1949, the United Nations Scientific Conference on the Conservation and Utilization of Resources met at Lake Success. As summed up by one writer, the purpose was: "That everyone will try to learn how to feed more people from an acre of land." That objective is a stimulus to the phosphate rock industry as well as other industries.

Jan 8, 1951

By E. F. Thomas

THE late George S. Rice was active in the inves--I- tigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and—to a lesser extent—Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,' if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable. Rice's system was put into operation in a mine in Harlan County, Kentucky,3 but subsequent experience has shown that it did not take into account two important factors—avoidance of pillar-line points and maintenance of adequate development in advance of the pillar-line abutment area. For ten years after Rice's retirement the USBM did little investigation and research on bumps, chiefly because so few were occurring that there was not much cause for alarm. But in 1951 there were three occurrences involving fatal injuries, and the Bureau began a statistical survey in that year. C. T. Holland, head of the department of mines at Virginia Polytechnic Institute, was retained as a consultant. The resulting study' of 117 case histories brought out these important conclusions: 1) Almost invariably the bump occurred in a locality affected by the abutment zones of one or more pillar lines. 2) In most cases the locality of the bump was influenced by the abutment zones of more than one pillar line. The term pillar-line point has been used for many years in the Appalachian region for such a situation. Point is used in the geographical rather than the mathematical sense. 3) In pillar-line extraction the following practices are safest in preventing bumps: a. The mine layout should provide for pillars of uniform size and shape along the extraction line. b. The mine layout should be planned so that no development need be done in the abutment zone of a pillar line. c. The layout should permit open-end extraction of pillar lines from the next goaf, so that it will not be necessary to resort to pocket mining, splitting pillars, or any practice that will involve driving in the direction of the goaf within the abutment zone. d. Pillars should be large enough to support area without undue roof and floor convergence before establishment of a pillar line. These are, of course, generalities, and while they are useful in laying out areas where bumps can be expected, they are of limited help in many mines that were committed to a system of mining before it was realized that they were subject to bumps. Under such conditions it becomes necessary to choose between the following alternatives: 1) Abandon the territory, except for pillars that offer no extraction problems. 2) Through experience select the pillars that are most heavily loaded, and, by augering, induce bumps from a safe vantage point so that impinged loads are relieved. This method was first developed at the Gary, W. Va. mines of U. S. Steel Corp. and later adapted to mining thick coal beds at Kaiser Steel's Sunnyside mine in Utah. No scientific method is available to determine where to drill within a loaded pillar. Although this method of unloading has worked very successfully at Gary—with one exception—

Jan 1, 1959

By V. E. McKelvey

The Phosphoria formation of the northwestern states presents a stimulating challenge to workers in every field of mineral technology. In addition to its large reserves of phosphate, the formation has been found to contain important amounts of fluorine and several metals, such as vanadium, nickel, and molybdenum. Because these minor metals in the Phosphoria do not have their usual glitter, concentrations of them are not easily discovered nor appraised. Like the phosphate itself, production of these metals very likely can be achieved only through use of costly chemical methods, for their mineralogy precludes treatment by the usual methods. In addition, in much of the area the containing rocks lie in complexly folded and faulted structures, which complicate mining and increase its cost. Yet the chain of research necessary to establish what elements are present; their geographic and stratigraphic distribution and reserves; the most suitable methods for recovering them; the combination of beds which, when ruined and processed, will yield the greatest recovery of the most valuable elements; and the methods most adaptable to their profitable extraction may well lead to the development of an important mineral industry and may make possible a significaut reduction in the cost of fertilizer this in itself would be an achievement of momentous importance—and at the same time make the nation more self-sustaining in critical materials. Although this research has great

Jan 1, 1950

By Henry Hebley

IN preparing this paper it has been the aim of the writer to keep the problems of both producers and consumers in mind. Until now, no attempt has been made to familiarize each group with the other's practice and limitations. This paper is an effort to acquaint the readers with some of the factors pertaining to the problem and cost of mining and preparing steam coal, and also to the economics of producing steam with such coal. In recent years all lines of endeavor have turned to intensive mechani-zation in order to lower the unit cost of production. The average fuel consumption in steam electric generating stations has dropped in 20 years from 4.0 lb. to 1.4.1b. per kilowatt-hour; while the modern power station can generate 1 kw-hr. on a fraction under 1 lb., or 13,000 B.t.u. coal. Also, the amount produced per man has in that same period risen from 3.8 to 8.2 tons, owing to the use of modernized equipment below ground for coal cutting, drilling, shooting, loading, hauling and hoisting. Unfortunately, the rapid speed of 5 tons per minute of operation at which the coal is loaded mechanically precludes any appreciable removal of impurities at the coal face, so that the raw coal is hoisted containing a markedly higher percentage of impurities than the hand-loaded coal, which was subjected to the scrutiny of the miner during loading. Also, during the past 20 years, certain seams of coal lying close to the surface have been made economically available by the improved design of electrically operated shovels and draglines for the removal of overbur-den running as high as 56 ft. This strip coal frequently contains so much ash in the raw state (Table 1) that it would have no sales value. There-fore, coal preparation must be adopted to beneficiate the raw product. Some seams in the United States have a decreasing ash content with decreasing size, owing, in all probability, to the fact that the coal is friable while the impurities are hard, causing a concentration of the low-ash material in the fine sizes. Illinois No. 6 coal being rather hard, naturally the reverse is true.

Jan 1, 1937

By J. J. Gilman

Zinc monocrystals, when compressed nearly parallel to their basal planes (within 20), deform in a new way; and certain deformation markings, called "-bands," are typical of this new mode. Characteristics of these bands are described. Mechanical behavior of low angle zinc monocrystals was investigated in some detail. Recrystallization did not occur upon annealing of banded specimens that were free of deformation twins. -Bands do not seem to be the result of nonbasal slip, but rather, a result of a microbuckling mechanism. u-Bands differ qualitatively and quantitatively from ortho kink bands. A dislocation model, consistent with some of the features of u-bands, is described. THE plastic deformation of zinc monocrystals with slip planes (0001) nearly parallel to the stress axis was studied in this investigation. In a previous investigation, it was shown that some low angle zinc crystals (those with slip planes making angles of more than about 2.5+1° with the compression axis), deform by ortho kinking while others (those with slip planes making angles of less than 2.5+1° with the compression axis) deform in a new way.' This new mode of deformation will be described in some detail here. Some of its striking features are: 1—it operates only for compressive stresses, 2—its temperature dependence is anomalous, and 3—it exhibits a new type of "yield-point" behavior. The mode of deformation to be discussed is not new in the sense that no previous evidence of its existence had been reported. The markings that it creates on the cleavage surfaces of zinc crystals have been described by several investigators.'" However, this is the first time that it has been made to operate under controlled conditions so that its response to mechanical variables, temperature, and aging treatments could be investigated and its geometry completely described. Apparently. Jillson' as well as Holden3 and Pratt" believed that the small bands they observed were simply small versions of ortho kink bands. In fact, two of these authors3,6 "alled the markings "micro kink bands." In spite of the precedence, it is felt that this term is not entirely suitable because these bands do not have the same genesis as kink bands, and they are qualitatively different in structure. As will be indicated by later discussion, the bands seem to be related to the tensile deformation bands observed in aluminum. The present author has chosen to call the bands "micro deformation bands," or simply ",ubands," and the deformation process, ''p-banding." Experimental Methods Crystals were grown from 99.999+ pct Zn obtained from the New Jersey Zinc Co. The details of the technique are given elsewhere." It should suffice to say that the crystals were seeded for orientation control, and precision pyrex tubes were used for molding them. About 40 crystals were used, yielding some 130 specimens. Fig. 1 illustrates the typical form of the specimens and shows how the orientation angles are defined. The crystal specimens were usually 1 3/4 in. long and about 150 mil in diameter. The angle between the slip or cleavage plane (0001) and the specimen axis is designated by xo, while a is the angle between the maximum slope of the (0001) plane and the nearest close-packed direction [1210], vary ing from 0°to 30°. The crystals were cut into specimens with a jeweler's saw and the ends were squared by filing (specimens held in V-block). Crystals of this orientation are stiff toward bending, so this procedure introduced only deformation localized at the ends. Then the specimens were polished either chemically in 50 pct HNO³ or electrolytically in 20 pct chromic acid. The mechanical tests were made with an Instron testing machine. This machine weighs by means of electric strain gages on elastic bars and is quite stiff, since the full-load deflection of its load cells is at most 0.002 in. Most of the testing was done at a

Jan 1, 1956

EXECUTIVE COMMITTEE OF THE BOARD OF DIRECTORS W M Peirce, Chairman Philip Kraft, Vice-Chairman Francis B Foley Hjalmar W Johnson Thomas G Moore ENDOWMENT Cleveland E Dodge, Chairman C F Kelley John D Bradley Harvey S Mudd J Coulter W A Sinsheimer N Eavenson Wilfred Sykes C Jackling Clyde E Weed

Jan 1, 1951

For the year ending February, 1918 PRESIDENT PHILIP N. MOORE ST. Louis, Mo. PAST PRESIDENTS WILLIAM L. SAUNDERS NEW YORK, N. Y. L. D. RICKETTS, NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON, NEW YORK, N. Y.

Jan 4, 1917

By C. F. Knutson, Martin Felsenthal, J. D. Lung, J. D. Sudbury

This paper has been written to summarize the laboratory and field studies leading to injection of Pacific Ocean water into the Third Grubb formation. Laboratory tests for studying the permeabilities of cores to Pacific Ocean water are described. Resu1ts of these tests showed that the water could be successfully injected if it is chertzically stable, sterile, and properly filtered. Clay swelling was shown to be a comparatively minor factor in permeability reduction. Studies leading to development of an economical system for properly conditioning the ocean water are discussed. It was necessary to control pH, calcium carbonate deposition, bacterial growth, iron solubility. oxygen, and suspended .solids. A relatively simple system combining the use of sulifur dioxide, a quaternary rlmmonium chloride, and filtration was shown to adeqrrately control all these factors. This combination has not previozrsly been used as a water treating technique. Evaluation tests of the water conditioning system prior to injection are described, and results of such tests are presented. Control measures needed to insure a continusously adequate water treatment are reviewed. INTRODUCTION The utilization of sea water for waterflooding has only recently been attempted. Knowledge of treating requirements has been limited, and in most cases no water treating has been done. Prior to the initiation of the Third Grubb zone pilot water flood at Ventura, Calif.,1,2 extensive laboratory research was done in an effort to define the treatment necessary to provide a suitable injection fluid. Close coordination and cooperation between field and research personnel were found to be the foremost requisites in developing the most economical and practical method for treating ocean water. LABORATORY STUDIES Plugging Tendencies of Untreated Ocean Water A program of laboratory studies was initiated for the purpose of evaluating whether ocean water could be injected into the formation for prolonged periods of time without causing plugging of the pore spaces of the formation. Because of the fairly low permeability of the formation (averaging about 40 md), it was realized from the outset that a water of exceptionally high quality was needed. Ocean water used in the laboratory studies was carefully filtered through ultrafine fritted glass filters, having nominal maximum pore sizes of 1.4 microns. Permeability tests were then performed on representative core material from the formation. It soon became apparent in these tests that filtration alone was not a sufficient treatment for the ocean water. Prolonged injection of the filtered water caused rapid plugging of the core samples. The permeability decline of a typical sample is illustrated by Curve A in Fig. 1. The several factors which can contribute to this plugging tendency are briefly reviewed below: Interaction with Formation Clays An evaluation of clay swelling effects on liquid permeability was made using core samples from the Grubb formation. An oil was chosen for determining the reference liquid permeability because it would not tend to react with any clays that might be present in the formation. The samples were then extracted, dried, and resat-urated with either treated ocean water, formation water, or fresh water. Permeabilities to the various waters were then determined. Results of this test series are summarized in Fig. 7. The difference between the oil permeability and water

Jan 1, 1957

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

The object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,' but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding"2 method, in which a seriesr of measurements is made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is determined at a given station for various increasing thicknesses of the ground.

Jan 1, 1934

By C. H. Mathewson, Robert Maddin, W. R. Hibbard

A SATISFACTORY mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.1 Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.3 EXPERIMENTAL PROCEDURE Half inch rods of alpha brass (nominally 70 pct Cu, 30 pct Zn) * were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.' In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pct nitric acid solution. The back-reflection Laue technique as described by Greninger5 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buerger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1948