Search Documents

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1936 arc available at Institute headquarters, unless otherwise noted They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTION Copies of the TECHNICAL PUBLICATIONS have been mailed to members of the Institute that are registered in the different classes A-Metal Mining, B-Milling and Concentration, C-Iron and Steel Division, D-Nonferrous Metallurgy, E-Institute of Metals Division, F-Coal Division, G-Petroleum Division, H-Industrial Minerals Division (Nonmetalhcs) , I-Mining Geology, L-Geophysical Prospecting Other members may obtain copies by writing to the Secretary Copies of CONTRIBUTIONS may also be obtained from the Secretary's office Additional copies are sold at the rate of 1 cent per page, minimum charge, 25 cents Non-members may purchase the papers to the prices mentioned

Jan 1, 1937

By C. E. Wethered

THE Morning mine is operated through one main working adit, known as No. 6 or 800 tunnel level. At a distance of 10,000 ft. underground from the portal is the vertical four-compartment, main working shaft, which extends to the 3050 level, a distance of 2250 ft. below the collar, or 800 level. Shaft-stations are cut and levels opened every 200 ft. of depth and the ore is stoped to the next level above. The vein is nearly vertical and the ore is usually fairly massive and brittle. Both walls are soft and slabby and much difficulty is therefore experienced in holding them. Stopes are usually carried up in short sections, approximately 200 ft. in length, that are mined as rapidly as possible in order to avoid a too great replacement or repair of stope timbers. The four-compartment vertical shaft, 110 ft. in the footwall of the vein, is the sole medium of outlet for all ore mined below the adit level. Two compartments of this shaft are used exclusively for hoisting ore, except at the time of changing shifts, when one compartment is used to handle some of the men and timber. The third compartment is equipped for handling men, tim-ber and all general supplies and is operated by a Nord-berg 300-hp. electric hoist. This hoist has a lifting ca-pacity of 14,000 lb. with an average rope speed of 800 ft. per minute. The fourth compartment is used solely as a manway and pipeway.

Jan 7, 1927

By Enid C. Plante

INTRODUCTION To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), marcasite (FeS2), orpiment (As2S3), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also examined to determine if its behavior could be correlated with that of pyrite or marcasite (FeS2). EXPERIMENTAL METHOD Mineral for Flotation and Contact Tests Mineral was prepared in the manner already described' and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and C02 free air bubbled through each suspension at a constant rate (about 1 bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation of oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.1 No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 FLOTATION OF "UNOXIDIZED" MINERALS WITH ETHYL XANTHATE AS COLLECTOR Fig I to 3, 4, 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox3 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C. Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1947

By A. S. Learoyd

THE Anthracite Division, Bureau of Distribution, of the United States Fuel Administration, came into existence about Oct. 20, 1917. There had been no definite policy determined upon and the distribution had been carried out by the producers and distributors of this fuel as under normal conditions. The domestic sizes had been shipped from the beginning of the coal year on Apr. 1 in about their usual proportions to the various sections of the anthracite consuming territory of this country, which, in a general way, extended as far west as Nebraska and Montana, and in the south along the Atlantic seaboard to Florida. With the advent of cold weather, about the middle of November, acute shortages commenced to develop all over the northeastern section of the country, due to largely increased demand by the public in general, to enormously increased population in centers where industrial war activity was concentrated, and by the needs of the war industries themselves. Commencing with the early part of December, this demand was aggravated by extreme low temperatures and heavy snow; and the production decreased for the same reasons. From that date until the change in the weather, about the latter part of February, it was simply a question of getting coal into communities as emergencies occurred, to take care of individual cases. No definite plan of distribution could be followed. The coal mined between Apr. 1 and Nov. 1 had been distributed as mined and, therefore, only current production was available for distribution. The Anthracite Division, during this period, consisted of a Director, two assistants, together with an office force of seven or eight clerks and stenographers.

Jan 8, 1919

"Acta Metallurgica" Robert Madden, Dec '60 Alfred Noble Joint Prize Committee F B Foley, Dec '61 American Association for the Advancement of Science William L Fink, Dec '60, H K Ihrig, Dec '61 American Geological Institute F C Kruger, Oct '60, Thomas L Kesler, Oct '61 American Power Conference Howard A Herder

Jan 1, 1960

By J. L. Giove, J. M. Hodge, R. G. Storm

The hardenability effect of molybdenum has been evaluated by a number of investigators, including one of the present authors.1,2,3,4,6 Considerable discreMncy exists, however, among the results of these various investigators, and two of them, Brophy3 and Kramer,4 have indicated that the apparent hardenability effect of molybdenun would vary, depending upon the other alloying elements in the steels being considered. The results of previous, unpublished work conducted at the Duquesne Works Laboratory of the Carnegie-Illinois Steel Corporation also have indicated significant differences in the hardenability effect of molybdenu~n in nickel and in chromium steels. The present investigation was undertaken in an effort to establish the mechanism governing this difference in the hardenability effect of molybdenum. This work involved both end-quench hardenability and isothermal transformation tests on two series of steels of varying molybdenum content. One steel contained 3 pct nickel and the other 1 pct chromium. It was hoped that such studies would shed further light on the mechanism of this behavior. Materials and Experimental Work MATERIALS The chemical compositions of the steels used in this investigation arc shown in Table 1. These steels were furnished by Battelle Memorial Institutc in the form of 100-lb induction furnace ingots. The top half of each ingot was forged to 1 3/8-in. square billets and then rolled to I-in. round bar stock for isothermal transforma- tion studies. The bottom half of each ingot was forged into approximately 1 1/4-in. rounds for end quench tests. All of the steels were normalized from 1650°F and tempered at 1100°F before nlachming to end quench or isothermal samples. END-QUENCH TESTS standard l-in. diam end-quench tests were made on each of the steels. The test bars were austenitized at 1600°F for 30 min,, quenched in a standard Jominy jig, and hardness surveys were made in all tests. The 95 pct martensite point was deterInined from hardness values5 and cheeked by metallographic examination. The jominy distance values for 95 pct martensite were converted to hardellability values in terms of ideal diameter (Dl), using a revised carve for the relationship between Jominy distance and ideal diameter. This curve was based on the cooling time from the A1 to the bainite nose temperatures rather than on the usual criterion of half-temperature time. The cooling rates as determined by Russell and Williamson9 were used as a basis for this relationship. The derivation of this curve is described in detail in the appendix. ISOTHERMAL TRANSFORMATION STUDIES Samples for the isothermal transformation studies were quarter sectors of 1/16.is-in. thick slices from the 1-in. round bars. All samples were austenitized for a total the of 15 min., transferred rapidly to a lead bath for isothermal transformation, and brine quenched from the lead bath. A time of 3 see was allowed for the sample to come to the temperature of the lead bath, and this time was not included in the isothermal transformation times. Each sample was examined metallo-graphically at a magnification of 100 diam. The per cent transformation was estimated by comparison with standard micrographs, and the values were plotted against the on log/log coordinate paper. At least 4 and as Inany as 10. points were plotted for each steel. A line was drawn through the points for each steel, and the times for 5 pct transformation were obtained from the plot for each steel. Isothermal transformation diagrams in terms of 5 pet total transformation, covering the temperature range of 800 to 1200°F, were determined in this manner for an austenitizing temperature of 1600°F. The times for 5 pct transformation at the bainite nose for austenitizing temperatures of 1800 and 2000°F were also determined in the same manner. These times for 5 pct total transfor-

Jan 1, 1950

By Albert H. Fay, William B. Plank

In practically all rock-excavation problem there is need for a careful study of the rock structure, its fault, cleavage or bedding planes, and even the texture of the rock itself. These studies should form the bases upon which an excavation method is selected and they should be carefully considered in predicting the amount and extent of the excavation. The need for such studies was forcibly illustrated in the problems involved in a cut made in 1929, along and underneath a 200-ft. high rock projection for a State highway near the City of Easton, Pennsylvania. The rock mass was badly faulted and also contained a number of cleavage planes at approximately right angles to the fault planes. Much of this structure was visible and could have been studied and analyzed before the work was begun. The State had rigid specifications as to finished grade and slope of cut, which apparently were made without reference to the geologic structure. The contractor complied with the specifications, under the close inspection of the State engineers. A tunnel blast was placed in the base of the cliff, with the result that 65 per cent more rock was broken than was intended by the specifications. About four years after the blast, the writers of this paper studied the circumstances surrounding the operation, to determine the cause of this excess excavation. Scope of Work The section of the roadway involved was about 200 ft. long and on a 6' curve. It was necessary to relocate points on the curve, from which all faults and cleavage planes were located and measured by the use of transit and clinometer. A plan (Fig. 1) showing the blasting tunnel, the roadway, and traces of the faults and cleavage planes on the level of the roadway, was prepared; also 13 cross-sections at varying intervals, showing the original face of the hill and the face after the blast. The original and final profiles of the rock face, taken from the plans of the State engineers, are shown in Figs. 2, 3 and 4.

Jan 1, 1937

Herewith are transmitted the joint report of the Treasurer and Finance Committee for 1934 and the reports for the same year of the Chairmen of the following Committees: Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for details of the year's activities. Finances.-Income for 1934 from all sources totalled $134,967 com- pared with $121,689 in 1933. The increase is accounted for principally by four items: $6000 increase in initiation fees and dues of new members; $1800 in current dues; $4000 in "back" dues; and $2800 in the sale of publications, including TRANSACTIONS volumes and technical papers in the form of "separates." In passing, it may be remarked that income from back dues during 1935 will be less than in 1934, for the obvious reason that the total amount of dues in arrears has shrunk and consequently there is less to draw from. Income from

Jan 1, 1934

Jan 4, 1951

THE Joint Committee appointed to consider a Code of Ethics for Engineers recommends, after delib-erate consideration, that each participating Insti-tute or Society adopt the short simple Code of Ethics following this report. The Committee further recommends that the following method of interpreting and administering the Code be adopted by each participating Institute or Society after any necessary provisions have been, made in the Constitution and By-laws of the Organization. The President of each Society or Institute shall appoint a Standing Committee on Professional. Conduct, to administer the Code of Ethics. The duties of such a Committee shall be to interpret the Code and to render opinions on any cases of ques-tionable conduct on the part of members that may be submitted to the Committee. These interpretations shall be reported to the Executive Board of the Institute or Society who may approve these interpretations, or take such other action as may seem just and necessary. The reports of the Committee on Professional Conduct, when approved by the Executive Board, shall be printed in abstract and in anonymous form in the Institute's or Society's monthly journal for the instruction and guidance of fellow members. This Committee on Professional Conduct shall be appointed in each Institute or Society by the President holding office at the time of the adoption of this Code and shall consist of five member one appointed for five years, one for four years, a third for three years, a fourth for two years and a fifth member for one year only. Thereafter, the President then holding office shall appoint one member annually to serve for five years, and shall also fill any vacancies that may occur for the unexpired term of the member who has withdrawn. These appointments shall he made from among the older members of the Institute or. Society, so that advantage may be taken of their mature experi-ence and judgment. The Committee after appointment shall elect its own chairman and secretary. The Committee shall have power to secure evidence or other information in any particular case not only from the organization's own members, but if it should seem desirable, from men in other professions. The Committee may also appoint sub-committees to consider certain cases when deemed necessary.

Jan 3, 1922

By J. A. Danko, C. D. Pears, L. D. Schmidt, J. P. McGee

This paper describes a pilot plant built on the campus of West Virginia University by the Federal Bureau of Mines station at Morgantown, West Virginia, for gasifying pulverized coal in a mixture of oxygen and steam at pressures in the gasifier up to 450 psig. The work upon which this report is based was done under a cooperative agreement between the Bureau of Mines and the West Virginia University. The goal of Bureau of Mines work at Morgantown is development of a low-cost process for producing mixtures of carbon monoxide and hydrogen for the modified Fischer-Tropsch synthetic-fuel plants, which may be shifted to produce hydrogen for coal-hydrogenation plants. Gasification with oxygen offers the inducement that the gas may be generated at the pressure at which the gas will be utilized in a gas-synthesis plant. Since the optimum pressure for the synthesis appears to be about 400 psig, the gas should be produced at approximately 450 psig to take care of pressure drops in the purification train and control valves. If the gas is generated at the pressure of utilization, only the oxygen need be compressed, not the raw synthesis gas. This means a saving in power of 5 hp per hour per 1000 cu ft (CO + H2), which is approximately a saving of 4 cents per gallon of gasoline. For example, consider a commercial plant generating 18,000,000 standard cubic feet per hour of raw gas that would produce approximately 10,000bbl of liquid product per stream-day. Assume that this gas would be 85 pd CO + H2 and that the oxygen required would be 320 cu ft per 1000 cu ft of CO + H2. The following estimate is based on a commercial centrifugal compressor. If the 18,000,000 std cu ft per hour of synthesis gas is compressed to 450 psig with 74 pd efficiency, 107,000 hp is required for compression. If the synthesis gas is generated at 450 psig pressure, only

Jan 1, 1953

By R. E. Lund

Josephtown Smelter employs the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. The process uses resistance-type electric furnaces. Flow of current through the sintered ore and coke charge develops the energy required for smelting at the reaction sites. To produce zinc metal, the furnace off-Gases bubble through a large "U"-tube filled with molten zinc which condenses the zinc to liquid; the metal is then mechanically cast into slabs. To produce zinc oxide, the furnace vapors burn in air and the resultant powders are collected. The smelter comprises three distinct circuits. One circuit produces American Process zinc oxide and high grade metal; another circuit produces tailor-made alloys of controlled lead and cadmium content; the third circuit produces prime western zinc metal and feedstock which is refined into special High grade metal and French Process zinc oxide. The roasting circuit utilizes multiple-hearth furnaces for deleading the zinc concentrates; fluid bed and suspension roasters are employed for desulfurization. Sintering produces a hard, porous furnace feed. The flexible smelting process is adaptable to consuming various kinds of secondary material. Extensive residue treatment accomplishes high overall zinc recovery. Smelter by-products include sulfuric acid, cadmium, and mercury.

Jan 1, 1970

By R. E., Head

THE use of lime in flotation has become so general in recent years that its functions are familiar to plant operators. The conditions and phenomena described in this paper are of interest because they are directly associated with the use of lime as a reagent and the resulting formation of lime scale worth nearly $1 per pound for its gold content. It is not known to what extent lime scale is common in flotation plants where lime is used, but as several occurrences have been re- ported, its existence is not limited to one particular plant. In November, 1927, the author's attention was drawn to a lime scale that formed on the sides of Callow flotation cells in the Walker Mining Co. mill at Spring Gar- den, Cal. The scale was described as an accumulation of hard material that built up on the sides of both the rougher and cleaner cells and in some instances attained a thickness of 2 in. The lime scale builds up in the cleaner cell at the rate of about 1/10 in. per month, or slightly more than ?12 in. during six months' operation. The rate of growth in the rougher cells is slower, and about 3/s in. of scale forms in six months. Analyses' of typical lime scale samples are as follows:

Jan 1, 1928

By E. I. Larsen, F. R. Hensel

According to statements by Guertler1 Smith and Hamilton were the first to study the copper-titanium alloys, but owing to the presence of large amounts of impurities their data are inconclusive. M. A. Hunter and I. W. Bacon later investigated the electrical conductivity and the temperature coefficients at room temperature. The present writers reported their results2 in November, 1930. Recently Kroll published data on copper-titanium alloys3 which agree closely with those obtained by the authors. Material Tested The titanium used was in the form of square sintered rods, the analysis of which runs as follows: titanium, 95.4 per cent; silicon, 0.7; iron,l.8; aluminum, 1.4; copper, 0.1; manganese, 0.05. The ingots were prepared in a high-frequency induction furnace in air atmosphere. Their analyses are given in Table 1. Up to 5 per cent titanium the alloys could be forged. Above that amount they were red short and broke up easily. Owing to their rapid absorption of nitrogen and oxygen from the air, the alloys with the higher amounts of titanium tend to form surface films which greatly increase the casting difficulties, especially when small masses of metal are handled. It was, however, possible to prepare sound ingots up to 25 per cent titanium. Thermal and X-ray Investigation The cooling curves of some of the alloys are plotted in Fig. 1, and R tentative diagram constructed from these data is given in Fig. 2. From this it is evident that the solid solubility of copper for titanium is approxi-mately 4 to 5 weight per cent titanium at 878" C., which is the eutectic temperature. The melting point of copper is lowered gradually by adding

Jan 1, 1932

By H. T. Hildage

Although Greater New York does not bear any resemblance to a great mining district, the mining operations that are being conducted in and about the city are both extensive and interesting in character. With regard to the extent, it may be mentioned that, at present, there is more dynamite used in New York than in any mining district in the United States; that there are under construction about 38 miles of tunnel, and that 66 miles more are projected, most of which must be constructed .in the near future; that since 1903 at least 2,000,000 tons of earth has been removed in underground work, in addition to about 3,500,000 tons that has been removed in open-cut in connection with tunnel-work, and many times this quantity that has been removed in excavating foundations for buildings not connected with tunnel-work; and that there are to-day probably more than 5,000 men engaged in mining-work in and about New lrork City. These undertakings include almost every operation connected with underground work, from exploration by means of trench and boring, to the sinking of large shafts and the driving of large tunnels through every kind of ground from hard rock to soft, semi-fluid silt and quicksand. It is proposed in this paper to give a general description of some of the methods and appliances used in the opening-up of a " mine " in a large city, and a brief description of some of the &'mines" now being developed in New York, connecting as far as possible the methods described with the particular work for which they were designed, in order to give a general idea of the

Jan 1, 1908

By Bartlett W. Paulding

Since its introduction to the petroleum industry in 1949 by Clark,1 hydraulic fracturing or "hydrafracing" has developed into a widely respected and useful technique for increasing production from petroleum reservoirs. Even then, Clark described production increases of from 6 to 100 barrels of oil per day (bopd). Since that time, others have described treatments in which production increased from 12 to 456 bopd, from only a show to 40 bopd;2 from 48 to 219 bopd; 3 from 500 to 1400 bopd and from a show to 192 bopd.4 Although representative of only a few of many successful hydraulic fracturing operational6 these increases in production attest to the past and potential value of the hydrafracing technique to the petroleum industry. The technique has received a considerable amount of theoretical and experimental attention.1, 5-20 Unfortunately, however, the degree of general understanding of the mechanics of hydraulic fracturing is still inadequate to solve many recurring problems. The practicing engineer is plagued with difficulties in predicting such factors as: (1) the required pressure and viscosity of the fracturing fluid to not only induce the fracture but to control the extent of its growth, (2) the strength characteristics and amount of proppant to include in the fluid so that the fracture is held open once the fluid pressure is decreased, and (3) the volume of the reservoir influenced by the induced fractures and the resulting increase in production. A major cause of these difficulties is the uncertainty associated with determining the orientation of the hydraulically induced fractures. One's natural conclusion in considering the problem is that the orientation of the fracture would depend on several variables, as, for example, the relationship between the viscosity and injection rate of the fluid and the

Jan 1, 1968

By W. S. Gatley, F. C. Appl

This paper presents a combined analytical and experimental study of chisel penetration vs time during chisel impact on rock, a problem of fundamental importance in improving the performance of roller-cone bits or percussion drilling toots. For a given force-time relationship between chisel and rock, the problem of determining the penetration (displacement) vs time of the chisel is formidable. This is so because the rock is a nonlinear system with distributed mass and distributed damping (friction, dissipation of energy due to rupture, etc.). Since the literature does not contain adaptable solutions, the rock behavior to impact was simulated approximately by an "equivalent" lumped system, that is, an "equivalent" mass, spring, dashpot system. With this assumption, an analytical solution was found for chisel penetration vs time due to a sinusoidal load between chisel and rock. From this solution were found curves, in terms of dimension-less variables, for the maximum depth of penetration vs the frequency of the sinusoidal loading and for the energy transfer vs frequency. The results of this analysis were used to predict the penetration rate of rotary rock bits us rotary speed. The curve indicated that an optimum speed exists. To verify this analysis, an experimental apparatus was constructed and used to apply a sinusoidal pulse to a chisel penetrating a rock specimen under atmospheric conditions. Strain gauges were mounted on the chisel shank and a velocity transducer was mounted between the chisel and the rock surface. The velocity was integrated electrically and picked up simultaneously with the strain gauge signal on an oscilloscope. Permanent records were made photographically to provide simultaneous records of force us time and penetration us time. In comparing the experimental results for limestone and dolomite with the theoretical results, good agreement was found in the frequency range of the experiments. Unfortunately, the inertia effect (peak penetration) indicated by the theory occurs at a frequency much higher than could be obtained experimentally with the apparatus constructed. A "rate-of-loading" effect is indicated theoretically, but has not yet been verified experimentally. INTRODUCTION The process of drilling with percussion tools or rotary rock bits is basically related to the transient response of rock to surface impact. Each time a bit tooth contacts the rock, high stresses are developed which result in penetration and rock removal. As the tooth moves on, stresses are relieved and a new cycle begins as the next tooth contacts the rock. Thus the drilling process, which consists of an endless succession of these cycles, can be studied in terms of a single cycle. It is apparent, therefore, that the study of single-chisel impact on rock is fundamentally important in improving the performance of roller-cone and percussive-type drills. Previous studies in this area have been conducted by Simon1 and Hartman2 by means of drop tests. In these tests a chisel was attached to a weight and allowed to fall, due to the force of gravity, so that the chisel was driven into a rock specimen upon impact. Strain gauges were attached to the chisel shank and the resulting force-vs-time curves were recorded photographically from an oscilloscope screen. The depth of penetration and crater dimensions were also measured. These tests have provided much valuable information but, as mentioned by the investigators, have not provided complete information on the effect of "rate of loading'! This is partly due to the fact that the chisel motion during drop tests is not a controlled motion which can be varied in form and frequency. Therefore, it seemed that additional information could be obtained by studying chisel impact under conditions where both the motion and the frequency of loading could be controlled. This paper presents a combined analytical and exper-

By Herbert Kynor

BY THE term mechanical mining is meant that operation, or series of operations, that replace the hand methods of mining. The first undercutting machine to operate in anthracite was placed in the Butler mine of the Hillside Coal & Iron Co., Dec. 23, 1910, by the Sullivan Machinery Co. The first Jackhamer used in the anthracite field was installed at the Wadesville colliery of the Philadelphia & Reading Coal & Iron Co. in Oct., 1912, by the Ingersoll-Rand Co. The first longwall conveyor was installed at the Dodge mines of the Delaware, Lackawanna, & Western Coal Co. in March, 1912. The first mechanical scraper equipment was installed in the Seneca mines of the Lehigh Valley Coal Co. in January, 1914. The amount of anthracite mechanically mined since the first mining machine was installed in 1910a is as follows: PENNA. COAL Co. D. L. & W., SCRANTON TEMPLE HUDSON YEAR AND HILL- TONS COAL Co., COAL CO., COAL CO., TOTAL. SIDE COAL TONS TONS TONS TONS AND IRON, TONS 1920 372,737b 367,000d 322,892 74,127 371,878 1,508,634 1919 950,786 no record 306,616 81,575 319,356 1,658,333c 1918 917,778 744,966 24,880 44,756 288,781 2,021,161 1917 757,940 838,800 5,050 57,279 164,180 1,823,249 1916 286,780 860,663 13,960 114,173 101,475 1,377,051 1915 428,819 592,169 8,253 1,029,241 1914 219,188 153,896 373,084 1913 171,505 171,505 1912 124,267 124,267 1911 40,319 40,319 1910 1,184 1,184 a. A slightly greater production than shown was obtained as the tonnage from individual operations is not shown. b. Decrease due to strike conditions in 1920. c. Does not include tonnage of D., L., & W. d. D., L., & W. decrease in 1920 due to having less mining machines in operation. There are about 150 undercutters in use in the anthracite region, 80 mechanical loaders, and 10 longwall conveyors.

Jan 9, 1921

By Bradley Stoughton, Henry M. Howe

This paper presents an experimental verification of some of the predictions made by one of us1 concerning the influence of certain conditions of casting upon the size and position of the pipe, and the position of the segregate, in steel ingots. The predictions which we have been able to verify are the following: A. That the pipe is shortened and the segregate raised: 1. By slow casting; 2. By casting with the large end up instead of down; 3. By retarding the cooling of the top, e.g., by means of a sinking-head. B. That the pipe is shortened by slow cooling. C. That the pipe and segregate lie in the last-freezing part. Our procedure was to cast ingots of wax (commercially pure stearic acid) containing a little bright green copper oleate (usually 1.5 per cent.) under varying conditions; to saw each ingot open along a longitudinal plane passing through its axis; and to examine the longitudinal section thus laid bare. In order to make the segregate or enriched part more distinct in color from the impoverished part, a very little red cerasine was added. An experiment which will be described later showed that the cerasine itself does not segregate markedly, if at all. Hence we may assume that the strong contrasts between the green and red shown in so many of our ingots are due, not to segregation of cerasine, but to that of the green oleate, in the wax which in itself is uniformly reddened with cerasine.

Jan 1, 1908