Search Documents

By K. K. Kershner, W. A. Calhoun, C. W. Funk

Future resources of aluminum may require the utilization of low grade ores to provide a more permanent protection for the nation. Aluminum minerals such as cloy, shale, and high iron laterites may become important sources. An evaluation of reserves is given. New laboratory results are reported on the Vereinigte desilication process. THIS report on future resources of aluminum metal emphasizes the necessity for investigating utilization of low grade potential ores to provide more permanent protection for the nation. Partial or complete interruption of the importation of high grade aluminum ores must be given consideration. Ultimately, aluminum minerals such as clay, shale, and high iron laterites may become the principal sources of aluminum. The development of extractive processes for treating these low grade materials is a step in long-range national preparedness that should receive more attention. In formulating such processes, the application of beneficiation methods for the purpose of classifying the several types of minerals before subjecting each type to the more expensive extractive procedures should be considered, and a careful survey of the basic factors of power sources, transportation facilities, and sources of raw material should be made. Domestic Bauxite Resources Of the domestic supply of current, treatable-grade bauxite, 95 pct comes from Arkansas. The present reserve of Arkansas bauxite suitable for metal production, including abrasive-grade, Bayer-grade, and modified Bayer-grade ores, is 34,000,000 tons. The total reserve of bauxite of all grades is approximately 75,000,000 tons. Reserves are estimated on a mined and dried basis. Data available to the Bureau of Mines in 1948 to 1949 were used in preparing Table I, which shows a breakdown by grades of bauxite for about a half of the reserves of the state. The modified Bayer ore, 10,555,500 long dry tons, is based on a cutoff of 8 to 15 pct silica. The sub- marginal 10,074,700 long dry tons is assumed to contain more than 40 pct gibbsite, more than 15 pct silica, and less than 32 pct available alumina. A considerable amount of this low grade material was consumed in 1949 and 1950. Additional tonnages of bauxitic and kaolinitic clays are indicated by the Bureau of Mines drilling project.' Applying a 50 pct factor to arrive at long tons mined and dried, the results of this project are approximately 31,500,000 tons kaolinitic clay at +35 pct Al²O3 and 11,800,000 tons kaolinitic clay at 20 to 35 pct A1,0,. Total reserves of kaolinitic clays are probably quite extensive—several times the reserves shown in the Bureau's work. Total reserves of bauxitic and high iron clays from the drilling program and previously established figures are 63,980,000 tons. The mineral dressing methods,' the lime-sinter process, he lime-sinter modification of the Pederson process," the lime-soda sinter process,"-' and the Alcoa combination processa. have been described in the literature and will not be elaborated upon here. The less familiar Vereinigte Aluminium-Werke process used by the Germans during World War 11 may require some amplification. It was used to bene-ficiate boehmite ores containing 12 to 18 pct silica for a feed to the European Bayer process. Ore was

Jan 1, 1952

Established as a Division March 24, 1922 R B Gilmore, '57, Chairman G L Yates, '56, Vice-Chairman Phil J Lehnhard, '56, Vice-Chairman John R McMillan, Past Chairman T A Pollard, Treasurer Joe B Alford, Executive Secretary 800 Fidelity Union Building Dallas 1, Texas

Jan 1, 1955

PRESIDENT OF THE COUNCIL. JOHN HAYS HAMMOND NEW YORK, N. Y. (Term expires February, 1909 ) VICE-PRESIDENTS OF THE COUNCIL SAMUEL B. CHRISTY BERKELEY, CAL. JOHN A. CHURCH NEW YORK, N.Y. PERSIFOR FRAZER PHILADELPHIA, PA. (Term expires February, 1909 ) J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, MICH. JOHN B. FARISH New York, N. Y. (Term expires February, 1910)

Jan 1, 1910

By D. V. Carter, C. Williams

During 1943 five oil fields and two gas-condensate fields were discovered in the East and East Central Texas district. The New Hope field, discovered by Tide Water-Seaboard in Franklin County, is the most important oil discovery since the Hawkins field in 1940. At the close of the year two oil sands were producing and two additional oil sands were being tested. The gas-condensate fields of Appleby in Nacog-doches County and the Stewards Mill field in Freestone County had only one producing well each. The Carthage field was extended 3 miles north and 4 miles west. Another well that was testing at the year end indicated a probable eastward extension of several miles. The Quitman field, in Wood County, was the most active from the standpoint of drilling operations. Approximately 48 wells were complcted during the year. The second and third most active fields were Hawkins field, Wood County, and Kildare field, Cass County, respectively. Wartime restrictions of material, together with manpower shortage and Federal spacing regulations, reduced the number of oil and gas-well completions from 265 in I942 to 171 in 1943. This represents a drop of 35 percent, or approximately 1/3, enough to replace the 531 producing wells abandoned in the district during the year. No changes were made in the price of crude oil in the district in 1943. The district produced 177,652,940 bbl. of condensate and oil during 1943. This represents an increase of approximately 11 per cent compared with the previous year. The East Texas field, which is the largest and most important field in the district, had an annual production of 128,568,647 bbl. of oil, which is approximately 6.5 per cent more than the previous year, and represents 72 per cent of the district's production of condensate and oil for the year. The district had an estimated basic daily allowable of approximately 509,000 bbl. of oil on Dec. 31, 1943. The entire district produced approximately 30 pcr cent of the state's production for the year 1943. The Hawkins field, Wood County, was operated 271 days during the year and with an average daily production of approximately 52,488 bbl. for the year. This field, which is the second largest in the district, produced 14,224,164 bbl, of oil during the year. Changes in annual production in certain fields in the district can be attributed to their ability to produce at higher rates, the demand, and transportation facilities in the war effort. The East Texas field showed an over-all decrease in reservoir pressure of 8.30 lb. during the year. Indications were that through the first quarter of 1944 the return of salt water to the reservoir was having a beneficial effect. It is hoped that, as more and more water is returned to the reser-

Jan 1, 1944

By M. A. Mahtab, T. M. Yegulalp

This paper presents the development and application of an approach for clustering fracture orientation data. Data are projected on the surface of the unit upper hemisphere and the clustering approach is applied in three steps: (1) randomness test and identification of dense clusters, (2) estimation of cluster statistics, using Bingham distribution, and (3) rejection of extremal data based on Chauvenet's criterion.

Jan 1, 1982

By Marcus A. Grossmann

This paper offers for consideration certain somewhat radical modifications in the iron-carbon diagram, these modifications being the result of the presence of notable amounts of alloying elements. When only small amounts of alloys are present, the standard iron-carbon diagram (Fig. 1) can be used with but insignificant changes; when larger amounts of alloys are present, however, it assumes a distinctly altered appearance. No comment is offered for the present except to call attention to the delta area, A4BM, which represents a region of mixtures of austenite and delta iron, just as area A3SP represents mixtures of austenite and alpha iron. Absence of Carbon We may turn at once to the effect of the presence of alloys. It has been found that in the complete absence of carbon, the gamma change will sometimes disappear entirely when sufficient alloying element is

Jan 1, 1927

By R. L. Slobod, H. A. Blum

A semiquantitative method for measuring the wettability of reservoir rocks has been developed. These data are needed for reservoir analysis and for interpretation of laboratory displacement studies. The wettability of a core sample is measured by the contact angle for the system oil-water-solid. These contact angles are calculated from the displacement pressure (threshold pressure) obtained by use of the centrifuge, using first oil-water and second air-oil in the same core sample. This method is based on the assumption that the air-oil and oil-water interfaces occupy similar positions in the porous medium when desaturation of the wetting phase is initiated. The assumption is also made that the Contact angle for the air-oil-solid system which is close to zero in value does not change appreciably even when the contact angle for the oil-water-solid system experiences marked changes. "Apparent contact angles'' for five different solids ranging from 31" to 82" have been determined, and changes irr the "apparent contact angle" of a given sample with laboratory use from 33" to 53' {lave been observed. INTRODUCTION Reservoir rocks vary in their wettability, 1,2,3,4 some being preferentially water wet while other are apparently preferentially oil wet. The degree of wettability, in theory, is measured quantitatively by the contact angle for the system solid-oil-water, hut in 1)practice this quantity is extremely difficult to determine." The need for obtaining some measure of this quantity has become obvious in recent years as a result of both laboratory. and field observations. Several reservoir.: such as the Bradford Sand in Pennsylvania and the Wilcox' at Oklahoma City are reported to be oil wet. If these report:: correctly reflect the true nature of the surface of the rock in the ground, then these reservoirs probably will not perform as predicted on the basis of a water wet rock. In the laboratory many core samples have been Observed to be oil wet. These samples, while perhaps not correctly representing the reservoir, have markedly different properties from water wet rock. The location of the phases is different (oil is in contact with rock instead of water), and other quantities such as the connate water, the capillary pressure curve; residual oil. relative permeabilities. and the recovery of oil by water flooding are markedly affected by the value of the contact -4 A further complication observed in the laboratory is the chang-ing of the wettability of a rock specimen with use. such changes mean that repeat runs on the same core are not the duplicate tests desired, but represent new experiments on a more oil wet material. The changes in surface characteristics are sometimes so rapid that by the time an experiment requiring several days is completed, the results may not be representative of the core as originally described, The, rock material itself (Silica. carbonates. etc.), whell Clean and uncontaminated, is water wet. There seems b( : little evidence of the presence of oil wet minerals such as heavy metal sulfides. The oil wetness of reservoir samples, therefore, is believed to be caused by the accumulation of an adsorbed film in which the polar group of a large organic. molecule is adsorbed on the surface leaving the organic or hydrocarbon part of the molecule projecting out from the solid. Such a surface is much more readily wet 17" oil than by water. These considerations indicate the need for a method which will provide some measure of tile wettalbility (Contact(angle if possible) for reservoir rock ..samples) The method should be capable of (1.1 distinguishing between tile wettalility of dif. ferent formation,.. (2) detecting (change. ill wettalbility of a core with use. and (3) measuring the changes in Wettability which may be accomplished with cleaning operations. such as the use of sodium silicate for increasing water wrettalbility." A preliminary report on such a method is preseted below. not with the idea that this procedure alone will Solve the wettabil-ity problem. but rather that it may provide encouragement to

Jan 1, 1952

By J. Earl Frazier, Howard A. Meyerhoff

IT is not known when silica sand was first noticed along the north coast of Puerto Rico, but the first mention of its occurrence was made in 1922, by N. L. Britton,1 who described its presence in isolated patches extending from Loiza westward beyond Manati. Further observations were made in 1925 and 1926 by Meyerhoff,2 who extended the known occurrences still farther westward to the low hill belt in the Quebradillas limestone immediately south of Hatillo. The extraordinary purity of the sands, which in most localities exhibit no contamination from the nonsiliceous materials surrounding them, was quickly appreciated, and the feasibility of utilizing them for the manufacture of glass was investigated, initially by the Committee on Mineral Resources3 and later (1936) by the Puerto Rico Reconstruction Administration and by H. C. Ray, mining engineer of the Insular Bureau of Mines. In 1934 samples submitted to the Hazel Atlas Glass Co., of Washington, Pennsylvania, were reported to have the composition as shown in the table on column two. Appreciation of the quality of the sand prompted geological and quantitative studies of the deposits, as well as commercial investigations to determine the feasibility of utilizing it locally or on the mainland for the manufacture of glass containers. [ ] DISTRIBUTION OF THE SANDS The quartz sands consistently lie within the outcrop area of the Quebradillas limestone, the youngest of the Miocene formations in the Tertiary coastal plain that fringes the northern coast of the Island. Many of the deposits are closely associated with limestone outcrops, but some appear to be embedded in lagoonal sediments at some distance from rock exposures, and at least one deposit, near Dorado, has been reworked by waves and littoral currents. With this single known exception, the deposits consist of irregular, patternless patches of white sand, which have sharply defined contacts with the surrounding material. Although patches of sand are present in a 90-km. belt that is not more than 5 km. wide, extending from Loiza to Hatillo, they attain maximum size, purity and number in the north central coastal area between Dorado and Barceloneta. Fifty separate deposits have been mapped in

Jan 1, 1945

By John H. Puffer, Andreas H. Vassiliou

The Bemco mine area is within the Precambrian igneous and metamorphic rock terrain of the New Jersey Highlands province. Rocks In the area include a pyroxene granite, a hornblende granite, a quartz-oligoclase gneiss and a pegmatite and its host rock, a lens of amphibolite which becomes a sulfide-rich pyroxenite near the ore zone. The ore-bearing zone occurs along the hanging wall and foot-wall contact of the pegmatite which was emplaced discordantly into the amphibolite-pyroxenite.

Jan 1, 1985

By C. E. Capes

A number of novel but increasingly-important methods of size enlargement in liquid systems are reviewed. These techniques use relatively strong bonding and specialized equipment to form dense and substantially permanent agglomerates directly from particles in liquid suspension. In addition to separation of particles from suspensions, these methods have other broad objectives, including the production of granular (often spherical) materials, displacement of suspending liquid from the product and the selective agglomeration of one or more components of a multi-particle mixture. The underlying principles of the methods discussed include agglomeration by immiscible liquid wetting and by polymeric flocculants. Other procedures to produce granular, free-flowing products based on dispersion and solidification in liquids are also noted briefly. Applications in a variety of fine particle systems are considered with emphasis on minerals and fuels beneficiation and on waste treatment.

Jan 1, 1980

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

0. C. Ralston and F. Fraas—Dr. Sun and associates have presented an interesting paper not all of which is comprehended by us. The data assembled measure the deflections of particles in an electrostatic field as a function of a number of independent variables and some dependent variables that are not sharply differentiated. These data are all based on a Johnson type machine of definite, well-described geometry, something not often done in electrostatic separation literature. One new fact brought out by this technique is the effect of coal dust on admixed pyrite and quartz. The effects are opposite in character, as should be expected and we do not agree with the authors that these effects are negligible. Fraas' also used a multiple cell "distribution analyzer" and gives in fig. 5 of his paper a straight line plot with no humps or curves. This is not necessarily at variance with Sun's results because Fraas used a larger gap between electrodes and had no evidence of particles adhering to or dropping off the charged electrode. The section of Sun's paper on effect of surface conductivity contains a speculation that the dielectric constant "represents more or less the electrical conductance of the bulk body instead of the surface of the mineral particles." A simple picture of the meaning of the dielectric constant is that it is the specific inductive capacity of a dielectric when used as the dielectric between the plates of a condenser. It is at once evident that the above speculation confuses capacity with conductance—two definitely independent variables. We ask the authors to state in what group or subdivision their garnet belongs; what method and units were used in calculating the data of col. A, table I and their meaning; what was the temperature of the carrier roll and, finally, has any effort been made to investigate the effects of particle shape on distribution in the electrostatic field? S. B. Hudson—I have read this article with great interest. We have been engaged in research work on the principles of electrostatic separation in this laboratory for some time now, and our findings agree with those of the authors in many respects. The article shows evidence of careful and valuable research in the field of electrostatic separation. A "distribution analyser," very similar to that described in an earlier article by one of the authors," was incorporated in an inclined plate-type electrostatic separator designed and built in the Melbourne University laboratory in 1948 for investigation purposes.22 The actual splitting edges were machined from y! in. per-spex, and the paper hoppers were supported on linen thread immediately below the perspex dividers. These dividers fitted into machined slots in a framework to give accurate Yz-in. spacings. The hoppers (staggered) fed directly into a rack of test tubes, which is supported on a vertical pantograph arrangement. The rack was positioned with guides on the horizontal pantograph stand, and this ensured positive alignment when replacing the rack after making weighings. In later work, when much heavier feed rates were used, of the order of 30 to 40 Ib per in. per hr a rack fitted with rectangular metal containers and similarly aligned was used. Some work was done here on comparing the distributions of minerals when passed separately and when passed as a mixture, and it was found that there was quite an appreciable difference in the two results.= However, in our separator the particles do not pass down the plate in a single layer, and this difference is probably caused by collisions of one mineral particles with the other mineral particles. In most of the investigational work here, the change of the center point of the distribution is measured to establish the effect of a variable, such as voltage. Two minerals (zircon and rutile) have been studied rather exhaustively, and it was found that their distributions are very nearly normal. Owing to the sharpness of the distribution curves, the usual method of obtaining the mean or median was inaccurate, and was not used; instead the mean (also the median), calculated on the assumption of a normal distribution, was used to locate the center point of each distribution and proved satisfactory. The effect of polarity becomes very apparent in the plate-type separator where frictional charges play a very important part when using highly resistive minerals such as zircon. With rutile, a comparatively conductive mineral, polarity of the electrode has little effect. On the other hand, the magnitude of the voltage has a far greater effect on conductive than on resistive minerals. Shiou-Chuan Sun (authors' reply)—Thanks are extended to Drs. Ralston and Fraas for their keen interest in this paper. Their questions concerning coal dust,

Jan 1, 1951

By J. R. Mihalisin

THE application of electron-microscopic techniques to the study of high-temperature alloys has met with considerable success.' This is due, in part, to the submicroscopic nature of the phases present in this type of alloy making high resolution methods necessary. Among the newer electron-microscopic techniques, the extraction replica technique' has proven to be of great value. This method allows phases to be examined in situ in the microstructure and permits their identification by means of electron diffracticn. This technique eliminates the main disadvantage in using electrolytic extraction of residues as a means of phase identification; that is, the uncertainty of relating constituents identified in the residue to what is observed microscopically. In the course of work relating microstructure to physical properties in high-temperature alloys, it was found that the formation of grain-boundary carbide phases and intragranular precipitation of an age-hardening phase greatly influence strength and ductility at high temperature. In particular, it was found that the formation of a unique type of precipitate in Nimonic "80" (a nickel-chromium-aluminum-titanium type superalloy), termed cellular or discontinuous precipitate, at grain boundaries generally results in poor ductility at high temperature. However, this mode of precipitation can be avoided by proper heat-treatment. It was assumed that this precipitate was either a carbide or age-hardening type of phase. Using various etching procedures with the extraction-replica technique, it was found to be possible to extract the carbide and age-hardening phases preferentially in this type of alloy. Previous work has shown that the age-hardening phase can be extracted from superalloys merely by

Jan 1, 1959

By S. W. Parr

FROM a study of sulfur with reference to its specific combination in coal, published as University of Illinois Bulletin No. 111, 1919, it is now possible to determine the various forms of this constituent with a good degree of accuracy. This fact suggests two questions: (1) Are the same analytic methods applicable to coke? (2) Is there any correlation between the forms of sulfur as it occurs in coal and the residual sulfur found in the finished coke? The answer to the second question might be helpful in answering a still further question as to what chemical route the sulfur travels during the carbonization process. While the special studies along these several lines are by no means complete, a few preliminary statements are herewith presented. They may, at least, prove suggestive of further possibilities from a continuation of research along these lines. There is no reason, chemically, why the analytic methods devised for coal should not apply to coke and a fair amount of experience in connection with such use affords confirmation of this statement. The procedure in the case of coal may be briefly outlined as follows; Combinations of sulfur as sulfate, or sulfides other than FeS2, are readily dissolved without disturbing either the pyrite sulfur or the sulfur that is in organic combination by means of dilute hydrochloric, acid-1 part of concentrated HC1 to 10 parts of water or approximately 3 per cent. acid. Digestion at 60° C. for 24 hr. insures the complete removal of the sulfur thus combined. In freshly mined coal the amount of such sulfur is very small; weathering processes, however, may very materially increase the amount of sulfate present.

Jan 9, 1919

By R. B. Burt, James A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1-the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2-power required for pumping, 3-pump selection. The basic factors for a given problem will include: 1-weight per unit of time of solids to be handled, 2-specific gravity of solids, for calculation of volume, friction and power, 3-screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4-shape of particle or some means of determining a friction constant, 5-effects of percentage of solids, 6-development of a viscosity factor to be used in the overall calculations, 7-calculation of the lower limits of pipeline velocities permissible, 8-calculation of total head, pump horsepower, and 9-setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble, phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; -14 +35 mesh, 11.4 pct; -35 +150 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The -150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble, content of the matrix, i.e., the +14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum -velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is, smooth and- polished because of the scouring, action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump, changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1952

By C. E. Richards, C. N. Reid

The influence of preferred orientation on the incidence of defbrtnation tuinning has been studied. High-purity iron with almost vandonz grain orientation was cotnpared uitll iron of the sa)ne grain size and composilion lza,ing a strong (110) fiber texture. As expected from published work on single crgslfls, /he ))lean stress for the onset of luitzning-, and the l,olu)nt. fraclion of twinned nzaterial obserlled in lension differed fron the 1-a1ue.s it2 co?nPression for tnolerial with a slrong texlure. The llinning stress of "rctndorrl " )zalerial did not 17ary with the sense of the aPPlied unin.via1 stress, but sirprisinglg the incidence of 1c)i)zning- was about three 1i))zes greater ill conzp?&apos;ession Illon in lension. These results (Ire attributed entirely to ovienbation and may be nderslood in ler?ns of the shear slresses acting on the allowed twinning syster)is. J. HE twins most commonly formed in bcc metals may be described as regions of the crystal in which a particular set of (112) planes is homogeneously sheared by 0.707 in the appropriate ( 111) direction. A similar twin-related crystal could be produced by a shear of 1.414 in the reverse (111) direction but twinning by this large displacement has never been reported. Thus, twinning is unidirectional and a shear stress which produces twinning does not do so when its sense is reversed. The sense of a shear Stress is reversed when the loading is changed from tension to compression, or vice versa. Consequently, for a given orientation of a crystal relative to a uniaxial stress, only a fraction of the twelve (112) twinning systems are geometrically capable of operating in tension, and the remaining systems may operate only in compression. Therefore, when twinning is involved, there are expected to be differences in behavior between crystals tested in uniaxial tension and those tested in compression. This has been verified experimentally by Reid et 01.&apos; and Sherwood el al.,&apos; although a critical stress criterion was not encountered. Furthermore, twinning stresses in colmbium," tungten, tantalum,&apos; irn,&apos; i-Fe,\ nd molybdenum7 single crystals have been shown to depend critically on orientation, although again twinning did not occur at a critical value of the macroscopic shear stress. However, when twinning occurs, it generally does so on the most highly stressed systems, 1--4&apos;6&apos;8&apos;9 implying that the stress level does have some relevance to twin formation. In view of the large orientation dependence of twinning in bee single crystals, it might be expected that such an effect would be present in poly crystalline material which possesses a recrystallisation texture. Indeed, riestner" showed that the twinning stress in tension is very orientation-sensitive it1 <&apos;grain-oriented, silicon-iron;" this material possessed a very strong t c m^ii a nnr x_____k . i-_ii__ ri_______j. _x r»i_._:__i preferred orientation obtained by secondary recrystallisation. Reid et a/.&apos; observed a marked difference in the tensile and compressive yield stresses of polycrys-talline columbium which was rationalised in terms of the effect of a preferred orientation on twinning. No other such illformation is known to the authors. Several investigations of twinning in polycrystalline bcc metals have been reported in which the possible existence of a preferred orientation was not even mentioned. It is the purpose of this paper to show that there is a strong effect of texture on twinning in polycrystalline iron, and to poilt out the difficulty in eliminating preferred orientation in recrystallised metals. 1. EXPERIMENTAL METHOD Material and Specimen Preparation. Low-carbon, high-purity iron was obtained from the National Physical Laboratory in the form of $-in. diam rod which had been cold-swaged from a diam of 1 in. The composition of the material is given in Table I. The as-received bar was cold-swaged directly to 0.185 in. diam from which cylindrical tensile and compression specimens were machined. Specimen geometry is illustrated in Fig. 1. The gage length was 0.30 in. long and 0.10 in. diam; it should be noted that, apart from the extra heads which are necessary for tensile loading, the geometry and dimensions of the two types of specimen are identical. The specimens were heat treated either by sequence A or B outlined in Table 11. The essential difference between these two treatments is that in one case the material was repeatedly cycled through the y- to a-phase change in order to produce grains of almost random orientation ("random" iron)

Jan 1, 1969

By Evert Hoek

Summarising a conference is never an easy task, but I will try to keep my comments brief and to the point. There are a number of lessons which we have learned from our deliberations together during these past three days, and I will try to give you my impressions of these lessons and of their practical implications in open pit mining. The first thing that has become increasingly obvious during these discussions is that it is no longer acceptable to offer an &apos;Act of God&apos; as an excuse for a major slope or tailings dam failure. Disasters such as that at Aberfan in the United Kingdom have focussed the world&apos;s attention on the activities of the mining industry and the report of the commission set up to investigate the Aberfan disaster clearly showed that adequate knowledge was available and that failure to apply this knowledge did not qualify as an &apos;Act of God&apos;. The courts and the world&apos;s press are certain to impose increasingly harsher penalties and criticism on those held responsible for major failures, particularly of tailings dams, in the future. One of the major problems in applying available knowledge to slope problems is that attempts to apply this knowledge are frequently left too late. To provide an engineering solution in the case of a slope in an advanced state of failure is an almost impossible task, and it is essential that those responsible for the stability of a slope must learn to recognise signs of distress at an early enough stage for effective remedial measures to be taken. As our ability to solve slope problems improves, the time at which slope stability problems are considered in a mining project must move forward to a stage at which these problems can be anticipated and dealt with before they arise. Conferences such as this are important in that they enable us to exchange ideas and advance our knowledge to a level at which such predictive engineering will be possible. It has been encouraging to hear of mining projects such as the Bougainville Copper operation where slope stability studies were carried out as part of the overall evaluation programme and it is hoped that this will become a more common procedure in the future. Providing a safe slope in an opencast mine obviously costs money, either in terms of the reduced ore to waste ratio given by flat slopes or because of the cost of stabilization techniques such as drainage or the use of rock anchors. An optimum slope design will provide maximum safety at minimum cost but achieving this optimum is not an easy task. Any one of us could design a slope which would be stable to the end of time, but it is probable that that slope would be so flat as to be totally uneconomic in most open pit mining situations. On the other hand, if the overall economics of a mining project are so critical as to require slope angles which the engineer responsible for these slopes considers to be unsafe, it is his duty to make us could design a slope which would be stable to the end of time, but it is probable that that slope would be so flat as to be totally uneconomic in most open pit mining situations. On the other hand, if the overall economics of a mining project are so critical as to require slope angles which the engineer responsible for these slopes considers to be unsafe, it is his duty to make

Jan 1, 1971

By Layson, W. C.

ACCORDING to the records, Phelps Dodge made its original entry into the production of copper in the oldest copper mines of Arizona at Morenci in 1881. The ore body now being mined as the Morenci open-pit, as outlined by churn-drill holes, diamond-drill holes, and underground workings, is estimated to yield 230,000,000 tons of ore averaging 1.06 per cent copper. This development will add 2,500,000 tons of copper to the 900,000 tons already produced in the district. Some five years ago preliminary development of the ore body began, with big-scale production planned including the erection of a new treatment plant to be built near the mine. Inasmuch as the Morenci open-pit was an entirely new project this required the grading of roads, establishment of mining benches, construction of railroad grades, building of railroad tracks, erection of shops, as well as the purchase of the necessary equipment to satisfactorily and economically maintain the schedules of production forecast. Along with the preparation of the main ore body it was also desirable to mine and deliver to an experimental mill a relatively small daily tonnage of typical ore.

Jan 1, 1942

By K. Brack, G. H. Schwuttke

Annealing properties of subszerface amorphous lavers produced through high-energy ion implantation in silicon are studied. The buried layers are produced through the implantation of ions (nitrogen), ranging in energy from 1.5 to 2 mev. X-ray interference patterns, transmission electron microscopy, and resistivity profiling are used to study the annealing characteristics of the ion damage. The annealing experiments indicate a low temperature (below 700°C) and a high temperature (above 700°C) region. Significant changes occur in the amorphous layer during the high-temperature anneal. Such changes are corre-lated with the re crystallization of the amorphous silicon and the formation of subsurface (buried) silicon-nitride films. TODAY&apos;S main problems in the field of ion implantation are related to the accurate determination and prediction of 1) the distribution profiles of implanted ions, 2) the lattice sites occupied by the implanted ions, 3) the lattice damage produced through ion implantation, and 4) the annealing characteristics of damage centers in the lattice. This paper reports investigations concerned with the problems listed under 3) and 4). EXPERIMENTAL Our investigations cover the energy range of incident ions from 100 to 300 mev and from 1 to 2.5 mev. The emphasis of this study is on the energy range from 1.5 to 2 mev. The experiments are conducted with single charged nitrogen ions. To implant the ions a van de Graaff generator is used as described by Roosild et al.1 Accordingly, a gas containing the desired ion specie is passed through a thermome-chanical leak into a radio frequency activated source. The positive ions are driven into the van de Graaff with the help of a variable voltage probe. Emerging from the accelerator the ions drift into a magnetic analyzing system and here the desired ion specie is bent 90 deg into the exit port. The ion beam leaving the analyzer is defocused and drifts down a 4-ft long tube to hit the silicon target. At this position the 20 pamp ion beam has a circular cross-section of 2.1 cm. N2 is used as a source gas for nitrogen ions. The implantation target is silicon with zero dislocation density, 2 ohm-cm resistivity, (111) orientation, mechanically-chemically polished, and 1 mm thick. The target is mounted on a water-cooled heat sink and kept at room temperature. A fluence of 1015 to 1016 ions per sq cm is used. RESULTS 1) Silicon Perfection after Bombardment. High-energy ion bombardment of silicon has some striking effects on lattice perfection. Some results were reported in detail previously at the Santa Fe conference2 and are here briefly summarized for the benefit of the experiments described in the following. 1.1) Identification of Surface Films on Silicon. After bombardment all samples are found to be coated with surface films. The films on the silicon surface vary in thickness and color; they can be transparent, slightly brown, or opaque. The films are thicker and darker in the high-intensity area of the beam and they delineate the bombarded surface area of the crystal. The films produce electron diffraction patterns characteristic of carbon and of SiO2. Carbon is predominant. The presence of carbon in these films was confirmed by use of the electron microprobe. Formation of the films occurs independently of the ions used and is attributed to a contaminated vacuum of the high-voltage machine. The carbon is most likely the product of the pump oil which is cracked and polymerized under ion impact. The films stick tenaciously to the silicon surface and burn off in a low-temperature Bunsen flame. 1.2) Mechanical Perfection of the Silicon Surface. The mechanical perfection of the bombarded silicon surface was investigated through optical microscopy, electron microscopy in which the replica technique is used, and optical interferometry. No mechanical damage of the surface was visible after bombardment. However, if a bombarded sample is soaked for several minutes in hydrofluoric acid (HF), gas bubbles may develop in certain spots of the silicon surface. It is also noted that in these areas the surface film starts to peel off. Relatively large patches of film come off if the sample is soaked in HF during ultrasonic agitation. After HF treatment, pits may be present on the silicon surface. The pit dimensions are estimated to be as large as 50 µ. The pits appear in the region of most intense irradiation. 1.3) Lattice Perfection After Bombardment. No lattice damage is found on the silicon surface. Electron transmission micrographs and selected area diffraction patterns of the surface show no difference before and after bombardment. Measured approximately 2 µm down from the surface, the silicon lattice throughout this depth is of good perfection. Well-defined Laue spots and Kikuchi lines are obtained from the surface as well as from the indicated area below the surface. However, some radiation damage is dispersed in this top layer. A sharp boundary line separates this surface layer from a highly damaged layer which extends further downward into the silicon. Typical of this

Jan 1, 1970

By C. R. Criss, R. J. McCormick

ThiS paper .summarizes the development and perform. ance of the Coldwater Oil field, Isabella County, Mich. Production is obtained at a depth of 3750 ft from a dolomite reservoir, which is probably both Rogers City and Dundee. There appears to be no persistent barrier to vertical fluid movement between the Rogers City and Dundee, and both formations are believed to have a common original oil-water contact. No we1ls are open to production at the level of the Dundee. The discovery of the field in 1944 was followed by the drilling of 81 producing wells and nine dry holes. By the end of 1952, the field had produced 12,763,000 bbl of oil, at which time 69 active wells were producing 3600 B/D oil and 21,000 B/D water. The reservoir has an effective natural water drive, and bottom-hole pressure has declined 75 psi from an original pressure of 1453 psi. Oil is undersaturated at reservoir conditions with a solution GOR of 512 cu ft/bbl and a saturation pressure of 1190 psi. INTRODUCTION Although the Coldwater Field is now in its ninth year of production, it ranks seventh in cumulative recovery, and second in current daily oil production in the State. Following complete development of the field in 1946, it has consistently contributed approximately 11 per cent of Michigan&apos;s daily production. Coldwater appears to have a greater pay thickness than most fields producing from the Rogers City forma- tion in the west central part of the Michigan basin. Except as influenced by the extent of closure and the thickness of the oil column, reservoir performance is believed to be representative of Rogers City fields in this part of the basin. For this reason, it is felt that the following presentation of factual data for the field will be of general interest. HISTORY AND DEVELOPMENT Discovery of the Coldwater field during Aug., 1944, followed favorable subsurface geological correlations and core tests drilled to a shallow stratigraphic marker horizon. The field is located in the west central part of the Michigan Basin in Coldwater Township (T16N-R6W), Isabella County. It is 60 miles west-northwest of Bay City, and near the geographic center of the southern peninsula of Michigan. The discovery well flowed 200 bbl of oil the first 24 hours from the Rogers City dolomite at a depth of approximately 3750 ft. Field production is principally from the Rogers City with a minor amount assumed to come from the underlying Dundee dolomite, although none of the wells are open to production at the level of the Dundee. Both the Rogers City and Dundee formations belong to the Devonian system (See Geologic Column-Fig. I.) In addition to Rogers City-Dundee oil production, sweet gas is produced from the Michigan Stray sand of the Mississippian system at a depth of 1400 ft. The gas reservoir has approximately the same areal extent as the underlying oil reservoir. Although gas production is an important feature of the Coldwater field, this report is concerned only with the oil reservoir. The productive area is approximately 3200 acres. The pool is developed on a 40 acre spacing pattern with wells drilled in the center of the north half of 40 acre tracts, except for a few off-pattern wells drilled along

Jan 1, 1955

By John C. Robison

INTRODUCTION Sensitivity analysis is a means of gauging the impact of individual risks on a financing. Key risks can occur in three time periods: - Feasibility, engineering and construction phase; - Start up phase (usually through completion); - Operating phase (post completion). If a company has agreed to cover these risks prior to completion, then less attention will be paid to the sensitivity of the project in the first two time periods. Since the operating phase of the project generates cash for both operations and debt service and generally does not begin until two to six years after the loan is signed, it is wise to look at scenarios other than the projected "base-case" scenario in order to determine the project&apos;s capability to operate successfully under a broad range of probable future events. Lenders are compensated at a fixed spread over their borrowing base and generally are not compensated if the project is successful beyond expectation. They are also subject to the loss of principal plus funding costs if the project performs below expectation. Because of this, lenders establish sensitivities around the parameters of conservative projections developed in the project feasibility studies and the cash flows resulting from these projections. The initial cash flow projections should demonstrate the project&apos;s ability to meet cash costs, debt service requirements (principal and interest), and still have sufficient cushion to cover contingencies such as strikes, price fluctuations, force majeur situations, etc. (See Schreiber, Chapter 10). The selection of the level of sensitivity analysis to be performed is the result of both objective criteria, including probabilistic analysis applied to the technical parameters, and, of equal importance, subjective criteria applied by the analysts, especially with regard to the economic and financial parameters impacting the project cash flows. RISK SENSITIVITY Assumptions used in the cash flow projections should be realistic. Risks identified by the lenders should be identified and cash flows prepared to assess whether these project risks are acceptable. Typical project risks include the following (see also Chapter 9): - Sufficient reserves - quantity and quality - Product price - Production level - Operating costs - Availability of energy and supplies - Transportation and infrastructure requirements and costs - Interest rate - Completion risks - Tax level - Political risks - Cost over-run risks - Operator experience - Management - Technological risks - Environmental permits and risks - Foreign exchange risks - Insurance coverage - Equity of sponsors - Inflation rate - Capital expenditure during project life In order to see the effect on the cash flow projections, each risk should be analyzed for its impact on the cash flow generating capacity of the project. Sensitivities can be examined to see if the resultant cash flow projection will meet the lenders minimum credit standards. 1.Reserve Sensitivity In general, lenders will not assume the reserve risk. However, it should also be noted that lenders receive loan proposals in which reserves range anywhere from proven to possible. Sensitivities are not generally run for various reserve levels and reserve estimates are either considered acceptable or not acceptable by the lenders.

Jan 1, 1985