Search Documents

By F. E. Bash

IN recent years, there have been a number of experiments conducted to determine the rates of heating and cooling of various sizes and shapes of steel ingots. Up to date, however,-most of the published data has dealt with small sized ingots, the largest being an 18-in. (46 cm.) cube, the data on which was presented before the Iron and Steel Institute in May, 1918, by E. F. Law. It is due to thus lack of information on the rate at which large ingots absorb heat and come to temperature that the heating- practice varies so widely in different plants. One of the questions over which there is much debate is the proper rate of heating of large ingots for forging and the time actually required for the center of a mass of steel to come to forging temperature. As a continuation of experiments described by M. E. Leeds1 and at the request of Mr. G. R. Norton of the Sizer Forge Co. and Mr. R. C. Drinker of the Emergency Fleet Corpn., the test described in this paper was carried out on a 24-in. (61 cm.) round ingot and the rate of heating and cooling determined under regular production conditions. The ingot had been partly forged at one end but, on developing a flaw, had been scrapped so that it was available for test. The size and shape of the ingot and its position in the furnace are shown in Fig. 1.

Jan 9, 1919

By J. L. Green

Virginia-Carolina Chemical Corp., in its Florida Operations, uses both roller mills and ball mills in dry grinding of phosphate rock. The roller mills have been in operation since 1954 in the Mining Department. The ball mills were installed and put in operation in 1960 in the Harding Concentrate Superphosphate Plant. The roller mills in the Mining Department are used to grind phosphate rock for outside customers. This involves short notice orders of varying grinds, grades and types of rock. The ball mills grind phosphate rock for use in V-C's own phosphoric acid and concentrated superphosphate plant. These mills grind generally two types of rock for one grind. In 1959, a 10% speed-up was made in the operating speed of the roller mills. This paper deals with the operational gains and resulting cost savings which evolved from this speed-up, and compares the present operations of the roller mills and of the ball mills in grinding phosphate rock. In January 1959 it was decided to determine the feasibility of reducing the grinding cost on the roller mills, per ton of rock ground, by speeding up the mill 10%. At this time, one mill was completely reconditioned so it would be in top condition. Extensive tests were then run both before and after the mill speed-up to determine the resultant cost savings. These tests showed that, due to this 10% speed-up, the mill capacity was increased approximately 20% and grinding power costs per ton were reduced approximately 10%. Table I shows the results of these tests. Each test run actually represents several of the same type rock and grind, averaged together. Each test run lasted approximately three hours. The validity of these runs has been confirmed by subsequent operation in grinding over 1,000,000 tons of phosphate rock. Accurate records have been kept on power consumption and repairs as well as tons produced. Two types of feed rock were used for the tests — pebble phosphate rock and flotation phosphate concentrate rock. The pebble phosphate rock size is approximately 80-90% plus 20 mesh. The flotation concentrate phosphate rock size is approximately 15% plus 20 mesh and 95% plus 100 mesh. The same two types of rock feed were used for all the test runs. Test Nos. 1, 2, and 3 were run at the original mill speed of 85.5 rpm on the vertical shaft. Test No. 1 was run with a feed of high grade flotation concentrates; the desired fineness attempted was 70% passing 200 mesh. Tests No. 2 and No. 3 were run with a feed of low grade pebble. Test No. 2 was run for a desired fineness of 70% passing 200 mesh. Test No. 3 was run for desired fineness of 50% passing 200 mesh.

Jan 1, 1963

ASIDE from the John Fritz Medal, in which the Institute partici¬pates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as fol¬ lows the Robert W Hunt Medal and Prize, the J E. Johnson, Jr , Award, the James Douglas Medal, and the William Lawrence Saun¬ders Medal ROBERT W HUNT MEDAL AND PRIZE The partners of Robert W Hunt established a fund which was, presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded tinder the following rules¬ 1 The award shall consist of two prizes first of a gold medal, second of a sum of money, a certificate to accompany each prize The money prize shall not be awarded to a member' over 40 years of age, but under unusual circumstances, both prizes may be allotted to one per son provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on non and steel The scope of the term "iron and steel" shall be determined by the sub-committee consideing the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main con¬ti ibutions to the industry have been in the improvement of production and quality of material

Jan 1, 1923

By David S. Butts

There are many solution mining operations that use solar ponds as a mineral recovery step. Other locations in the world are now under investigation to recover minerals by solution mining but require the cheap energy of solar ponds to make the recovery viable. This paper shows a step-by-step material balance system that can be used in both simple and complex solar ponds. Use of this system will help the engineer determine if solar ponding efficiency can be improved or if solar ponding will work at all with a given set of conditions. Even the most complicated solar pond can be reduced to six flow streams. These are (1) feed, (2) exit, (3) leakage, (4) entrainment, (5) salts, and (6) evaporation. The equations developed in this paper will allow the solar pond engineer to easily evaluate the effect of each of the flow streams on the mineral production of a pond or pond complex.

Jan 1, 1985

By J. W. Spretnak, G. W. Cunningham

A study has been made of the growth and disappearance of voids in the interface of pressure bonded copper. The formation of visible voids is primarily due to spheroidization and coalesence of microvoids produced during the application of pressure. The microvoids could be prevented from forming by the application of high pressures or by increasing the ductility of the copper. Migrating grain boundaries were found to be more effective in void removal, than stationary grain boundaries. DURING the course of an investigation on the mechanism of pressure bonding, it was found that voids formed in the bonding interface which inhibited migration of the interfacial boundary and grain boundaries in the bond region. Therefore, an effort was made to determine the nature of the voids and how they form, grow, and disappear. This paper reports the results of such an investigation. The existence of interfacial voids is not solely a characteristic of massive components of metal which have been bonded by the application of heat and pressure, but is a phenomenon which has been observed in sintering as well. Simonsen attempted to study the sintering process by hot-stage microscopy and thereupon observed the formation of interparticle porosity as sintering proceeded. It was assumed that the porosity was due to grooves created at the location where grain boundaries joined the surface of the particle. Pranatis, Castelman, and seigle2 have also observed voids along the areas of contact in wound-wire specimens used for sintering studies. They did not discuss the point in detail since this behavior was not general, but they did suggest that the voids might develop as a result of stresses along the interparticle contact area. In previous investigations on pressure bonding, workers3 have suggested that voids may exist in the region where mating surfaces are placed in intimate contact, but the existence of the voids was not verified and no attempt was made to study the growth and disappearance of these voids. Durst noted the existence of pores in roll-clad structures prepared by cold reducing two sheets to force them in contact and then annealing to improve the bond. Since his unbonded regions contained a gas which he assumed to be insoluble, he proposed a mechanism which consisted of spheroidization of the unbonded regions and a growth of the contact area, but no speculations were made regarding disappearance of the gas filled pores. One interesting comment made by Durst was the suggestion that flattened voids with sharp corners which are produced during roll bonding will have a greater driving force for spheroidization than the more rounded pores created by pressing metal powders and thus spheroidization and neck growth will occur at lower temperatures. In this study it was necessary to demonstrate conclusively that voids can actually exist in the interfacial bond area. Experimental work was then directed toward a study of the mechanism whereby the voids grow and subsequently disappear.

Jan 1, 1963

The volumes of Transactions, which are published annually, contain the list of officers, rules, etc., the Proceedings, and the papers revised for final publication. (In this revision, after the preliminary publication, authors are permitted to use the largest liberty; and the changes and additions made in papers are sometimes important. It should be borne in mind by those who study or quote a paper in the preliminary edition, that they may not have in that form the ultimate and deliberate expression of the author's views. It should be added, however, that in the majority of cases there are no important changes.) These volumes are for sale as follows, in paper covers:

Jan 1, 1910

By A. D. Schwope, L. R. Jackson, A. M. Hall

In the course of an extensive investigation of the comparative properties of several types of copper, data were obtained on the cold working and subsequent recovery and recrystallization of the copper. In this paper, relations between the degree of cold work and the course of re-crystallization are developed. In particular, it is shown that the course of recrystallization over long periods of time and at low temperatures can be predicted with reasonable accuracy from short-time high-temperature recrystallization data. Materials Used in The Investigation Three types of copper were used in this investigation; these were tough pitch, OFHC, and OFHC copper with 15 oz per ton of silver added identified herein as Lots C, D, and F, respectively. The material was supplied by the American Metal Co. Ltd., and processed by the Rome Cable Co. The analyses of the three types of copper are given in Table I. Originally, it started as wire bars 4 X 4 X 54 in. These bars were heated to 871° C in air and hot rolled to % in. rod. This rod was cold drawn to 0.204 in. rod (70 pct reduction) in three passes and annealed at 427°C for 4 hr. A portion of the 3/8 in. rod was saved for more detailed cold-drawing experiments. Starting with the annealed 0.204 in. rod, hard-drawn wires were produced by cold drawing to 0.081 in. wire in 7 passes (84.4 pct reduction in area). Half-hard wires were made by cold drawing the 0.204 in. rod to 0.102 in. wire, (75 pet reduction) in 6 passes and annealing at 427'C for 4 hr. This annealed wire was then drawn to 0.081 in. wire, (37.1 pet reduction) in 2 passes. Square rod was made by hot rolling wire bars to Re in. rod in 8 passes. This rod was then cold drawn to 0.445 in.-diam rod and annealed for 346 hr at 538°C. It was then cold drawn to 0.325 in. rod and again annealed at 538°Cf or 3 1/2 hr Hard square rods were then made by cold rolling this material to 0.257 X 0.257 in. rod, a reduction in area of 20.5 pct. Half-hard square rods were made by cold rolling to 0.268 x 0.268 in. square, annealing for 3 1/4 hr at 538°C and cold rolling to 0.257 x 0.257 in., a reduction of 8.5 pct. Soft wire or rod was made from all types of copper by annealing the hard-drawn material at 343°C for 3 hr in steam. The grain size of the annealed 0.081 in. wire varied slightly among the three lots: from o.o15+.oz5 mm in the silver-bearing OFHC to 0.035-0.045 mm in the OFHC copper. The annealed 0.257 in. wires were more uniform in grain size, averaging about 0.035-0.045 mm. Representative structures are shown in Fig I. Effect of Cold Drawing and Tensile Strain on Strength of Copper Conventional tensile tests were performed on the three types of copper in the various degrees of hardness described above. Results of these tests are tabulated in Table 2. The results in Table 2 are 6

Jan 1, 1949

By F. Keller, A. H. Geisler

Some of the important changes that take lace in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrys-tallization. Although improved metal-lographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based 011 the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mah13-l7 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chcmical or anodic treatment. .After removal from the metal sample by one of the special techniques described by Evans,l9 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,l7 nicke1,7 iron3,8,9 and a nickel-beryllium alloyl1 by heating; films formed on iron8,9 by chemical action; and films formed on aluminum3-'" by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

Jan 1, 1957

[University of Alabama University, Alabama Mining and Metallurgical Society Meets first and third Mondays each month WILLIAM L. ALLMAN, President L. M. LOTOTZIY, Secretary J. R. CUDWORTH, Faculty Sponsor RICHARD L. BOWRON, Counselor University of Arizona Tucson, Arizona Miners' Society HARRY GARRETT, President AL WALLACH, Secretary A. J. THOMPSON, Faculty Sponsor E. D. GARDNER, Counselor Birmingham-Southern College Birmingham, Alabama Geology Journal Club WALTER WOLF, President LELAND CULLIGAN, Secretary R. S. POOR, Faculty Sponsor A. J. BLAIR, Counselor]

Jan 1, 1940

By W. H. Smith

IN connection with some recent work on the effect of impurities on the ductility of chromium, it appeared desirable to know the solid solubility of carbon in chromium. A literature survey indicated that this information was not available. Although considerable work has been done on the Cr-C phase diagram,&apos;.&apos; previous investigators have been more concerned with the structure and phase boundaries of the carbide phases than with the terminal solid solution. The phase diagram shown in Fig. 1 is taken from the work of Bloom and Grant&apos; and represents the most recent determination. As indicated by the dashed line, the a solid-solubility limit was not determined. Experimental Procedure Alloys of chromium were prepared from hydrogen-treated and vacuum-degassed electrolytic chromium plus spectrographic grade carbon. The oxygen and nitrogen content of the alloys was <0.002 pct. After melting, analysis of the alloys showed them to contain 0.02, 0.08, 0.15, and 0.55 pct C. Pieces of the alloys were heated in a protective atmosphere to various temperatures and then quenched after holding for a time sufficient to insure equilibrium. Microscopic examination of the as-quenched alloys for the presence of a second phase was used as a measure of the solubility limit. The heats were made in a multiple hearth arc-furnace using a zirconium-gettered static argon atmosphere. A zirconium melt was made before each Cr-C heat. Triple melting was used to insure ingot homogeneity as shown by microscopic examination. The alloys were prepared by adding portions of a 4.5 pct C-Cr master alloy to high purity chromium. The carbon contents listed previously were those obtained by analysis. The nitrogen and oxygen contents after arc melting were both <0.002 pct. Sections 1/8X1/4X1/2 in. were cut from the 100-g ingots and a hole drilled in one end in order to suspend the sample from a molybdenum wire. After the surface was carefully cleaned, a sample of each melt was hung in a mullite tube heated externally by a platinum resistance furnace connected to a vacuum system. The lower portion of the mullite tube was sealed to Pyrex and closed off several inches below the furnace. This was filled with sili-cone oil kept cold by circulating cold water around the outside of the Pyrex. Quenching into the oil bath was achieved by melting a fuse wire supporting the sample. It required about 4 sec for the sample to cool from 1400" to 600°C. This severity of quench was considered satisfactory to freeze-in the high temperature equilibrium. For tests made at temperatures of 900" to 1200°C, heating was done in vacuum; for tests above 1200°C, an argon atmosphere was used. The holding time employed ranged from 12 hr at 900°C to 6 hr at 1400°C. Experiments were performed at temperatures of 900°, 1000°, 1100°, 1200°, 1300°, and 1400°C. Microscopic examination for evidence of a second phase was done at X1500. Experimental Result The microstructures of a 0.08 pct C-Cr alloy as-cast and after quenching from 1300°C are shown in Figs. 2 and 3. A 0.15 pct C-Cr alloy quenched from 1300°C is shown in Fig. 4. The data obtained from the quenching experiments is shown graphically in Fig. 5. If the Van&apos;t Hoff equation is obeyed, a plot on a logarithmic scale of the mol fraction of solute vs the reciprocal of the absolute temperature should give a straight line. For dilute solutions the weight percentage can be substituted for the mol fraction without introducing any appreciable error. The Van&apos;t Hoff equation can then be written as where H is the heat of solution in calories per mol. The slope of the straight line on the log pct C vs 1/T plot gives the value of AH. Assuming that the Van&apos;t Hoff equation is obeyed, which is probably justified for the dilute solution of carbon in chromium, the heavy straight line shown on Fig. 5 represents the best fit of the data. This line was obtained as follows. On Fig. 5 the results of the microscopic examination of all alloys following quenching were plotted and designated as to whether one or two phases were seen. Below 1100°C all alloys showed a second phase on quenching. The heavy vertical lines shown in Fig. 5 therefore represent the possible range of the ter-

Jan 1, 1958

By G. Sachs, E. J. Ripling, S. I. Liu, J. J. Lynch

It is a generally recognized fact that by repeated straining the fracture stress of any metal is reduced to a fraction of its value for static loading. The value of this fatigue strength depends upon numerous factors, such as the states of strain and stress, the limits of straining, and the number of repeated loadings or cycles The large volume of previous investigations on fatigue is concerned entirely with large numbers of cycles, say exceeding 10,000 and up to 500,000,000. However, the changes in fracture stress and fracture strain occurring after a small number of repeated loadings have attracted little attention. Apparently the only investigations of this type are those byLudwik4.5 who subjected steel, copper, and aluminum wire to repeated torsion. In each test the torque was varied between identical values in the two directions of twisting. Depending upon the magnitude of the moment, fracturing occurred after a number of cycles, up to 10,000. The results of Ludwik&apos;s tests will be discussed later Such torsion does not readily yield actual stress and strain values. Therefore a pre- liminary study was made of the effects of repeated direct stresses, that is, tension and compression stresses. Because such tests are considerably more tedious than torsion tests, only high stresses were used in the preliminary work, yielding definite changes in metal properties after a few cycles. It was found in these tests that strains could be controlled more readily than stresses in the investigated range of high stresses. This paper, consequently, deals with the effects of strains of equal magnitude but different signs. The metal was first prestrained in static tension by a certain amount then subjected to compression to yield the same amount of strain after unloading. This loading cycle was repeated up to a maximum of seven times. After various cycles, the stress-strain curves in tension were determined, up to fracturing. As material for these tests, the aluniinum alloy 24ST was selected because it exhibits a comparatively small amount of necking in the tension rest This alloy permitted, therefore rather accurate cont.rol at the high strains necessary to produce fatigue failures at less than seven cycles. The results of this invest~gation appear sufliciently interesting to extend the method of attack in various directions It is intended to study (11 the effects of cycles up to a tew thousands and (2) the effects of strains of different magnitude in tension and compression respectively &apos;The latter variable also includes a. a special case the effects of compressive strains.

Jan 1, 1949

By Virgil W. Carmichael

In the Fort Union formation of western North Dakota, eastern Montana and northeastern Wyoming there are immense tonnages of lignite and subbituminous coal that have not yet been evaluated in terms of present economic conditions. The general lack of detailed geologic and topographic maps of this region, coupled with a considerable interest in some of its deposits, has spurred the North American Coal Corp. to develop a rapid, economical method of producing its own maps on which to base a quantitative evaluation of the coal reserves involved. The techniques the company employs in this mapping and evaluation program are simple photogeologic and photogrammetric procedures that can also be applied to other exploration and mining work. The air photos, in addition to being used for photogeologic interpretation, have been successfully applied to locating drainage cuts, haul roads, and road metal deposits as well as for various property studies and general mine and reclamation planning. The present discussion will deal primarily with North American&apos;s photogeological reconnaissance method of mapping and evaluating relatively flat- lying to shallow-dipping coal beds with limited topographic control and a minimum of core drilling. The field tools employed under this method include aerial photographs and pocket stereoscopes, engineering levels, aneroid barometers, portable transceiver radios and core drills. Field information developed on the photos is transferred to maps for measurement of reserves and overburden. To date this method has been used to map and analyze nearly 6 billion tons of Fort Union lignite and subbituminous coal.

Jan 8, 1969

By L. Michael Kaas

The mineral industries are striving to expand their use of the computer&apos;s ability to process exploration, geologic, and mining data. Digital plotting programs and devices are continuing to gain wider use for lowering the cost and the time required to produce many types of maps and cross-sections commonly used by mining companies. Mineral engineers and geologists will soon be using a new tool, computer graphics, to greatly facilitate the use of computers to solve a large number of industry problems. By means of cathode-ray-tube (CRT) displays, an engineer can search large files of geologic data; display elevation contours, geologic structures, and ore grades; construct geologic and mining cross-sections; and compute tonnages for mining plans or ore reserve estimates. Examples of both digital plotting and cathode-ray-tube problem solving approaches are discussed in this paper.

Jan 1, 1969

By Dilip K. Paul, Charles H. Jacoby

The economic importance of salt domes has been recognized throughout the world, primarily because of oil and gas accumulations on their flanks, and to a lesser degree, for the value of their salt and potash. Recently they have become of value as hosts for cavities used to store hydrocarbons. In the near future we believe that their main value will be a source of geothermal energy. Although tremendous effort has been expended on the understanding of the geology and physical characteristics of the strata intruded by salt domes, relatively little energy has been exerted in the comprehension of the salt dome itself. Salt domes have long been recognized as a geological heat anomaly. With respect to other sedimentary rocks, salt is a good conductor of heat. Expressing values in 10-3cgs units, sedimentary rocks vary from 1.0 to 8.0; metamorphic rocks from 5.2 to 8.4 and igneous rocks from 3.1 to 9.8. Rock salt in its pure form has a thermal conductivity of 17. Thus a salt dome can be expected to act as a conduit bringing heat vertically from deep within the earth&apos;s crust.

Jan 5, 1974

By Frank G. Norris

Slag control is adjustment of the composition of the slag, especially with respect to the FeO content. The theoretical method of slag control would be to charge a mixture of pig iron and scrap of given composition into the furnace, to melt always at the same carbon, and, after a uniform ore addition, to tap with a constant slag composition. Such conditions are not even approximated. Both scrap and pig iron are of variable, and, in many cases, unknown composition. The charge is oxidized to a variable extent during melting. The result is that the FeO content of the slag, and consequently of the metal at tap, varies over a wide range. In order to make a nearly uniform product, this variation must be compensated for in some way. One way is to adapt the ladle deoxidation to the requirements of the metal. The other is to control the slag. In a general sense slag control may be considered as a method of compensating for variations in the composition of the charge and in oxidation during melting. The method of slag control for low-carbon steel was developed by Dr. Herty at our Butler plant3. Use of this method enables the furnace operator to tap heats at a more nearly constant FeO content and, therefore, to use a more nearly uniform deoxidation practice. The desired FeO and the accompanying deoxidation will depend on the application of the product. This statement implies that 0.10 carbon steel finished with a 15 FeO slag may be essentially different from a 0.10 carbon steel finished with a 30 FeO slag. In making low-carbon steel, the desired carbon places a lower limit on the FeO content of the slag, because the slag must be sufficiently oxidizing for proper carbon elimination. With this degree of oxidation, the phosphorus specification is met without difficulty, and there is little danger of phosphorus reversion. Thus a limiting factor in high-carbon heats is of slight importance in low-carbon heats. For heats of 0.05 to 0.07 per cent carbon, the FeO content of the slag may be controlled at

Jan 1, 1935

By W. J. C. Venter

The use of activated carbon to improve the selectivity in the separation of base metal minerals from bulk concentrates played an important role in the development of separation techniques employed at Tsumeb and Kombat mines. The Kombat mine, owned and operated by Tsumeb Corp. Ltd., is located in the Otavi Valley in the northern part of South West Africa, approximately 213 air miles north of Windhoek and 38 air miles south of Tsumeb, at latitude 19° 43&apos;S and longitude 17º 41&apos;E. The mine is linked to all major centers by both national railroad and tarmac highway systems which pass right through the town. The Otavi Minen- and Eisenbahn-Gesellschaft (OMEG) mined ore on the farm Asis from 1908-1925. Tsumeb Corp. Ltd. acquired the mineral rights in 1947, started diamond drilling in 1954 and commenced mine development in 1960. The mill started production in 1962 when proven ore reserves were 3,378,084 st containing 2.85% Cu and 2.90%Pb. Annual production of 248,411 st was increased in May, 1967 to the rate of 422,990 st, which was still being maintained in 1971, when ore reserves stood at 3,054,701 st of grade 1,91% Cu and 2.5% Pb.

Jan 4, 1973

By S. F. Emmons

IN a report upon the geology of Leadville and vicinity, which is still in the hands of the Public Printer, I have given, at some length, my conclusions as to the genesis of the remarkable silver-lead deposits of that region, and the data, gathered during a long and careful consideration, upon which my views were founded. In the brief abstract of this report, published in 1881, the bare conclusions are given, with but few of the facts upon which they were founded. Since that time, these conclusions have been variously criticised, and it has even been assumed that the views I expressed with regard to these deposits were intended as a theory of ore-deposits in general. Had my final report been printed, no such misconception could have occurred; for, in that I explicitly disclaim any intention of general application of the theories there presented. Even in the abstract I am unable to find any statements which would. justify such a conclusion. Since my Leadville work, however, I have had further opportunities of examining ore-deposits, and have given the general subject much thought and study, and, as a result, I have made in my own mind certain generalizations, which, I am conscious, need the test of a far greater number of practical applications than I have yet been able to make, but which, I think, it may be well to present to the members of the Institute as suggestive, that their own observations may further prove or disprove them. I shall use my Leadville observations and the criticisms which have been made upon them as a sort of text for my remarks. The salient facts, which I thought to have determined with regard to the Leadville deposits, which, as is well known, are silver-lead deposits in a dolomitic limestone, overlain and in

Jan 1, 1913

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

By Robert F. Mehl

THIS essay is an attempt to present the elementary facts and ideas concerning the growth of crystals, especially of metals. Freezing, like all heterogeneous processes, is a process of nucleation and growth; it manifests itself in metallurgy primarily in the freezing of ingots. The preceding paper in this volume discusses nucleation; the paper to follow describes ingot solidification. The present paper will treat of the growth of nuclei to large crystals, embracing a long series of phenomena, many of which are familiar to metallurgists.† Crystal growth, it will be immediately noted, occurs not only in the freezing of metals, but in the freezing of all substances; and it is a prominent and familiar phenomenon in crystallization from solutions, aqueous or otherwise, and in crystallization from the vapor phase. It will be necessary to include such systems in this discussion, for so much of value to metallurgists has been learned from their study. Apart from this, so far as metals are concerned, it will be simpler to limit the discussion to the freezing of pure metals and of solid solutions. Other types of freezing-eutectic, peritectic, etc.-will be excluded, though they have much of interest and of importance. BASIC MECHANISM OF FREEZING Ideally, nucleation and growth processes can best be considered from the point of view of isothermal reaction and upon the assumption of random nucleation. In. such an ideal case, nuclei form at random, and at a characteristic rate either constant or changing with time, and grow to spherulites at a characteristic rate, constant or changing with time, Fig. I.. On the simplest assumption, the reaction rate-in this case the rate of freezing-is a resultant of these two component rates. The reaction rate equation may be written in terms of these two component rates. The formation of pearlite from austenite closely approaches this ideal case. The ideal case forms a very useful point of departure in considering real cases. Various factors of reality produce deviations from this assumed ideality. In freezing, the isotropic medium, the melt, passes to the anisotropic solid, the crystal. Crystals are lattices of atoms, and the unit cell is often referred to as a crystal unit. Rosenhain, many years ago, represented the nucleation and growth process on freezing in the manner shown in Fig. 2, feeling, intuitively, that there must be some crystal unit in crystal growth. It now appears that this may be true, though his picture requires much elaboration. The greatest deviation from ideality lies in the nonisothermal nature of the freezing process in metals. To approach this properly it should be recalled that many nonmetallic substances freeze slowly. Tammann, to whom we owe the classic approach, studied complex organic materials in which (as in the case of eutectoid steels at high

Jan 1, 1951