Search Documents

By R. I. Lahring, C. G. Inks

A surfactant waterflood, using a block copolymer of ethylene and propylene oxide (PLURONIC L64*), wa., started in 1956 in Kansas to determine the commercial feasibility of such a process. The production formation was the Bartlesville sand at a depth of 1,400 ft. Leares in the test area had attained both primary and secondary production peaks, and were on a normal decline when the tests were initiated. The injection wells were taking water at a reasonable pressure and none of the operating conditions were particularly unusual. The leases were selected primarily because of normal operating conditions, and not because of any serious problems demanding remedie>,. Oil production and water injection data were recorded during the 10-year test period, and their compilation indicates that the surfactant resulted in an increase of about 9 percent in secondary oil production. Other benefits derived from the surfactant injection were lower injection pressure that resulted in reduced power consumption and reduced erosion of the pumps; and lower calcium scale buildup. These fringe benefits more than offset the cost of the surfactant used. Introduction During the past several decades, considerable research has been carried out on secondary recovery of crude oil that remains in the producing formation despite the most efficient, current primary production practices. Methods are constantly sought of increasing recovery of oil, while at the same time improving the economic efficiency of operations. One method that has received intensive study over the years is the use of a surfactant as a waterflood additive. Laboratory tests show conclusively that dilute solutions of surfactants remove considerably more oil from uncon-solidated sand cores than does water alone.'- The loss of surfactant by adsorption at solid-liquid interfaces has caused serious doubt that surfactants can be used economically as waterflooding additives. This is especially true with anionic and cationic surfactants, and to a lesser extent with nonionic surfactants. This work was undertaken to determine the effectiveness in increasing oil production by injecting water containing small quantities of a nonionic surfactant. The surfactant selected was PLURONIC L64*, a block copolymer based on ethylene and propylene oxide, having the following structure The selection of the test site, a typical shoe-string sandstone type of field located at Batesville pool, Toronto District of Woodson County, Kans., was made because of its normal primary and secondary recovery operating conditions, and not because of any serious operating problems. When the tests were begun, the field was experiencing the customary post-peak production decline of a waterflood. Using for the tests a field that was on a normal production decline, while maintaining constant all variables other than the addition of the surfactant. was of varamount importance if success or failure was to be attributed to a particular cause. It was reasoned that if a surfactant was added to the injection waters and nothing else was done to influence the oil production or injection of water, the effects of the surfactant on the flood could be determined precisely. Production History The first well in the tested field was drilled in 1935. Gas repressurization began immediately, but it was not until Aug., 1938, that the major portion of the field was developed. During the period of repressurization, 1,700 MMcf of gas was injected. As can be seen from the curves of Fig. 1, the production peak from gas injection was attained in 1937 and a normal production decline followed. Early in 1942, water injection wells were drilled and injection of water Was initiated. The amount of water injected increased as more injection wells were drilled until a peak injection rate of 2,700 BID was reached in

Jan 1, 1969

By John V. Beall

The Glidden Co., a newcomer to the mining industry, will be putting on stream its Lakehurst mine and concentrator this spring. Ilmenite-bearing placer sands will be mined and concentrated in a spanking new combination gravity, magnetic and high-tension separation plant. Glidden, well known as a paint, chemical and food manufacturer, consumes titanium dioxide as pigment in its paint business. The commodity is produced at the company's Adrian D. Joyce Works in Baltimore from ilmenite purchased in India and Australia, The Lakehurst operation, handily located in Ocean County, N. J., will dampen any deficiencies in quantity or price which might occur from foreign suppliers. This objective is no overnight concoction of The Glidden Co., because the move at Lakehurst was preceded by an attempt to start up in Florida. That project was abandoned when it was found that the titanium dioxide values were largely in rutile-a mineral which does not lend itself readily to the digestion process of the Baltimore chemical plant.

Jan 1, 1962

By H. R. Cooper

Beginning from the point of view that process control of ore flotation can be approached by on-line analysis of processing behavior, an equation was developed which has characteristics useful for a multi-variable feedback loop. The application of this equation to optimizing control with a data acquisition system will be discussed in Part 11. OBJECTIVE OF CONTROL The purpose of developing a feedback method for concentrator control is to provide a means for determining ore processing behavior in order that data describing the ore can be used to make appropriate changes in control conditions while the ore continues to flow through the flotation circuit. In absence of simple linear relationships between pairs of variables in the flotation process, attention is directed to the need for a generalized relationship which possibly would incorporate all pertinent variables. It would be possible to apply such an equation to the control of variables in a concentrator in real time according to operational requirements as ore gradually changes in quality and processing behavior. To meet this objective, it is necessary to define relationships describing flotation performance in terms of performance variables capable of being measured on-line, either with on-line instruments and analyzers or with manual methods lending themselves to quick determination of meaningful information. Relationships derived to meet this objective form a model for the flotation process. The evaluation of flotation parameters of the ore and the execution of control on the basis of the derived information while the ore is continuing through the process would constitute a feedback control system. Data for the following control and performance variables can be made available: 1) ore feed rate, 2) collector addition rate, 3) lime addition rate, 4) pulp density, 5) assay or multiple assays in feed, tails, or concentrate sufficient for material balancing, 6) particle size distribution in flotation feed, 7) froth height, and 8) frother addition rate. Other process variables, such as flotation air input and mechanical agitation intensity, are usually not considered as control variables and were not taken into account in this analysis. Other data, such as that describing the ore, would be useful for concentrator process control. However, information of this type (such as ore hardness, grain size of the mineral, chemical species of the mineral, and ore surface properties) being not presently measurable in the on-line sense, has the effect of causing disturbances in the system which can be detected only indirectly. The process control system being sought must recognize disturbances by their effect on measured performance followed by determining control changes to compensate for them in meeting the objectives of improved performance (perhaps higher throughput, maximum return, etc.). A suitable model for the process having capability of recognizing the effects of ore disturbances should provide the means for introducing proper compensation through control changes. This would be done by processing on-line data with the model to calculate coefficients reflecting ore characteristics. This procedure can only be applied in a typical flotation system when on-line data can be processed at faster rates than the usual rate at which the ore in flotation feed takes on significantly different characteristics. For example, material balance data can be accumulated in approximately 5-min intervals using on-line X-ray fluorescence analysis. The flotation system time constant might be 15 min including grinding. Ore changes having time constants longer than 1 hr could be accommodated using on-line feedback control by this procedure. FORM OF A FLOTATION MODEL A suitable form for mathematical expression of the flotation process is an equation involving rates, when each of the components entering into the separation can be treated independently by a rate equation. A first-order, kinetic rate equation can be written on

Jan 1, 1967

In opening the meeting I wish to express my greatest pleasure at being able to greet this joint session of the Mining and Electrical Engineers. As engineering develops, we find that the border lines between the different branches of engineering become more and more indistinct; the several fields overlap so much that they are three or four layers deep in places. It is only an accident that we couldn't have had the Mechanical Engineers also as a formal part of this gathering, because they are quite as much interested in this subject as the Electrical or Mining Engineers. A little history may enlighten some of those who have not been close to this work. A year ago last summer, there was brought to the attention

Jan 4, 1919

By John B. Pearse

In view of the great importance of accurate knowledge respecting the chemistry of iron and steel, as related to their physical properties, I come before you with a paper showing the great mass of work which has been heretofore done on the subject. I have tabulated the more important data I bring at this time, so as to draw out the results clearly. This information is accessible to all who will seek for it. I have made it the basis of my own practice throughout, and such knowledge is undoubtedly the only foundation for the successful practice of metallurgy. As is well known the ordnance corps of our army, after 1841, made exhaustive experiments on the properties of cast-iron. The investigations were undertaken in order to obtain necessary information on the reorganization of the corps. I wish to call your attention to the results obtained by a comparison of the chemical and physical properties of cast-iron for guns, to describe certain characteristic peculiarities of steel, and to give a brief history of the chemical work relating to carbon in iron. The Reports on Experiments on the Strength and other Properties of Metals for Cannon, published by H. Carey Baird, Philadelphia,

By Thomas M. Drown

IN a communication to this Institute at the Baltimore meeting, February, 1879,* on the "Determination of Silicon in Pig Iron and Steel," the method recommended was the treatment of the metal with nitric acid until action had ceased, and then evaporating with sulphuric acid until the nitric acid was nearly or quite driven off After filtration of the siliceous and carbonaceous residue, and washing with hot water and hydrochloric acid, a silica was obtained, on ignition, which was quite pure. Since this paper was read before the Institute, we have had large experience with the method, and * Transactions, vol. vii, p. 346.

Jan 1, 1880

By Martin A. Mayers

It has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimenta1 investigations of fuel-bed temperature1-4 have not been lacking, but the absence of any theoretical background has made it impossible to use the results of these tests as a basis for prediction, except in a very general may. A mathematical analysis", based on a somewhat simplified theory of the distribution of lieat in a fuel bed, lias recently been completed by the author. Even though numerical values of some of the coefficients are not known, the calculations result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calcu1ated. The uncertainty concerning the values of the coefficients referred to above is serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of the coefficients. For a more. extended discussion of the theory, see the A.S.M.E. paper5. Theory and Comparison with Experiment The theoretical analysis is similar to that used in the calculation of the stationary temperatures in a conducting solid in the classical theory of heat concluction. The fuel bed is pictured as a uniform, continuous, porous solid through the interstices of which air can be blown and ill which combustion can take place. The solid lias a finite thermal conductivity, so that heat may be transported in any direction, against the flow of air as well as in the same direction. While it is true that nothing

Jan 1, 1938

By Ogden B. Malin

In conducting the manufacture of extruded brass rods and brass forgings it has been noticed that there is considerable variation in the physical properties, particularly the machinability of different rods and forgings, even though the composition, working temperatures and method of manufacture remain the same. It is the purpose of this paper to attempt to establish the cause and extent of this variation, and also to determine whether variations in composition within certain defined limits influence hardness and machinability to any marked degree. The writer believes that this variation probably is due to the variation in grain size of the metal, therefore the microstructures of several compositions under various conditions of working were examined in an effort to establish this as a fact. Survey of Previous Work in Studying Extrusion Defects Very little has been published concerning defects in extruded and forged brass. In 1921, R. Genders1 $ delivered a paper before the British Institute of Metals, relative to a defect inherent in the extrusion process. This defect, commonly found in extruded brass rod, shows up in the form of a circle in a transverse section consisting of oxides and impurities, and is generally present in the last 25 to 30 per cent of the rod. Genders concluded that the defect is caused by the turning inward of the skin of the billet at the edge of the plunger because the inside of the billet is more plastic than the outside, which is in contact with the cooler container; the outside skin will lag behind to form the rear end of the rod. Genders suggested a movable die as a remedy, and while this met with fair success, it is not used in present practice. About the same time as Genders' experiments, Tucker2 and Rosen-hain3 conducted experiments using colored plasticene in the form of a billet, and found much the same defect as Genders. Dr. Rosenhain State College, Pa.

Jan 1, 1932

By R. S. Hutton

WHEN I had the honor of receiving an invitation to give the-Institute of Metals Lecture, it occurred to me that it might be of interest to review the advances which have been made in refractories, considering how important these materials of construction are in the carrying out of many metallurgical operations and what a large factor they represent in our costs of production. Frankly, I can claim no recent contact with the refractories industry and what little work I myself have been concerned with has been rather unorthodox in character. However, perhaps in consequence of this, I can approach the review without bias and include some suggestions which may prove stimulating or provocative to some of you, who have a more intimate knowledge of refractories and their uses than I Possess. It is neither possible nor necessary for me to survey the progress of industrial refractories, for this has been so thoroughly undertaken by others1-7 in recent publications. Perhaps the best way to get a broad picture of this progress is to compare the Faraday Society Symposium on Refractory Materials 20 years ago8, containing a report on one of the first attempts at standardized testing, with the American Society for Testing Materials Committee Report of February 1935. Suffice it to say, lest my provocative remarks be misunderstood, that I do appreciate that great advances have been made, particularly by companies that have established their own research laboratories and by universities and cooperative research institutes working for the common weal of groups of manufacturers or for national and international progress. The scientific study of the constitution diagrams of binary and ternary refractory oxides, which American workers have been foremost in under-taking, ? led by the work of the Geophysical Laboratory at Washington, has laid a firm foundation for the whole subject. It should be remem-bered, however, that to a much greater degree than with the constitution of metal alloys, the equilibrium conditions are so sluggishly arrived at

Jan 1, 1937

By Edward A. Loria

Vanadium is one of the materials being considered for use in fast-breeder nuclear reactors. It is a good heat conductor and nearly transparent to radiation, properties regarded as ideal for nuclear fuel containers. The problem has been the metal lacks ductility needed for forming. In our program at Reno Laboratory the effects of the U.S. Bureau of Mines (previous affiliation) the effects of oxygen, nitrogen, and carbon have been reported21,22 nd most recently the effects of boron and boron with carbon.23 The continuing study by the Ames Laboratory of the effects of hydrogen, the most subtle and fugitive element in its relationship to structure and properties, is commendable. The solubility of oxygen, nitrogen, and hydrogen in vanadium (and other bcc metals as well) is related to material purity. With the available limit on metal purity and the interaction (clustering) of hydrogen with the other interstitial and substitutional elements present in their base metal, would the authors comment on the tolerance of hydrogen in relation to oxy- gen that will avoid intergranular fracture and above what content or how seriously harmful in oxygen at various carbon levels? Understanding the true effects of hydrogen (and other interstitial impurities) in vanadium depends on knowledge of the amount present under various conditions and its distribution between various possible positions. Significant amounts of hydrogen may be in "thermo-dynamic" solution, but not as individual atoms in interstitial positions. It may be in grain boundaries, in subgrain boundaries, in vacancies, or in dislocations. Some of the hydrogen may be paired or in complexes with impurities in substitutional solid solution in vanadium. This makes the analysis of the effect of hydrogen vastly more difficult. It should not be expected that hydrogen in grain boundaries will affect slip in the same manner as hydrogen in interstitial positions, nor will the complexes react to heat treatment the same way as hydrogen in dislocations. It is gratifying that the authors have quoted results from two of our inestiations,' but neglected one2' which applied the Petch theory to electrorefined vanadium of high purity and analyzed the effects of oxygen, nitrogen, and carbon on the ai and ky values obtained by the extrapolation and grain size methods. Details can be found in the paper. Briefly, we obtained a ui value of 10,300 psi (t = 5150 psi) at 273°K. The metal also exhibited profuse twinning with high ductility at 123" and 77°K. Nitrogen was more effective than oxygen in increasing ui, the increase being about twice as much for the same impurity level. Carbon additions resulted in only minimal changes in Ui. The corresponding ky increased as oxygen and nitrogen increased, with nitrogen being more effective. Carbon additions resulted in little change. Although the difference in yield strength of vanadium was explained on the basis of the Cottrell-Bilby model of the tearing away of dislocations from the impurity atoms,

Jan 1, 1970

By J. M. Callow

HISTORICAL SKETCH THE selective action of oils for lustrous minerals was first disclosed by Haynes in 1860. In 1885, Miss Carrie Everson elaborated this idea and also disclosed the fact that acid increased the. so-called selective action. Her patent called for oils, either animal, vegetable or mineral, also for an acid or salt. The process was tried out on a practical scale in Baker City and Leadville, in 1889, and failed: first, because,, as has since been shown, of the unsuitability of the ore to flotation; and second, because the invention was too far in advance of the times. Then followed the Elmore brothers, first with their bulk oil processes and later with their vacuum method. The basic principles of oil flotation were undoubtedly covered by the above inventors, the work done since their time being merely a building up on ground work laid by them. Different kinds of oil, different quantities of oil, and all the varying degrees of agitation, were all exemplified and practiced by them in one phase or another, and the developments that have since been made are but elaborations of the fundamental principles laid down by Haynes, Everson, and the Elmore brothers. In 1902, the Potter-Delprat process was developed in Australia. In this process no oil was used, the mineral being raised by the generation of gas, brought about by the introduction of acid into the pulp. The mineral particles appeared on the surface of the separatory vessel, in the form of a scum or froth, buoyed up-by minute gas bubbles attached to them. This no doubt first gave the suggestion of gaseous flotation. In 1902, also, Fromont, an Italian, was granted a patent in which. he combined violent agitation with oil and gaseous flotation, the gas being generated within the pulp, in much the same way as in the Potter-Delprat process.

Jan 12, 1915

ON FEBRUARY 13, 1953 the Miami Copper Company signed a contract with the United States Government, through the Defense Materials Procurement Agency, whereby it under- took, with a base price of 27.359 per lb (subject to escalation based on wage scales and wholesale-price indices), to exploit a new ore body in its mine in Gila County, Arizona. Recoverable ore was estimated at 23,000,000 tons, averaging about 0.677 per cent copper. Moreover, the proportion of oxidized copper, difficult to recover by flotation concentrating, was so high that an average net recovery of only ten pounds per ton (0.5 per cent) was expected. The company proposed to mine the ore by the underground method known as undercut block-caving. Unfortunately the ore body, as has been true of all Miami's ore bodies, lay so deeply buried that no possibility existed of adopting opencut mining as has been done in recent years at Miami's neighbors, Ray and Inspiration. Probably the most distinctive characteristic of Miami's operations has been the extent to which it has developed and improved methods and equipment for underground mining. True, necessity was a potent stimulant, because its available ores since 1926 have been exceptionally low-grade; so, if the enterprise were to survive, it was necessary to keep costs at the minimum. This fact does not detract, however, in any way from the remarkable achievements of Miami engineers in conducting efficient and low-cost underground mining.

Jan 1, 1957

By W. A. Griffith

Fractional replication of factorial design, a general method for planning experimentation and for analysis of data obtained, is described as applied to a flotation investigation. This method leads to determination of optimum process conditions with minimum experimental effort. Its advantages over simple factorial design are demonstrated. A METHOD for planning experimentation and for analyzing the data secured will be demonstrated. This method, termed fractional replication of factorial design, employs a relatively small number of individual experiments to determine which of a large number of process variables are controlling, to determine which combination of levels of these variables is most likely to produce optimum results, and also to predict what results will be obtained with a particular combination of conditions not already tested. Although the general method is not new, having been developed by Finney in 1945,' the extent to which it can improve the effectiveness of applied research generally has not been recognized by metallurgists. The fractional replication procedure is particularly useful in flotation experimentation and an example from such an investigation will be used in the paper. However, it has equal value in any investigation in which similar experimental difficulties are encountered. In developing a flotation process for a particular mineral separation, the investigator is inevitably confronted with the following difficulties: 1—There are a large number of potentially important process variables. 2—Results of individual experiments are not highly reproducible, due in part to the difficulty in precisely controlling all the variables. 3—Considerable effort is expended in conducting individual experiments. 4—There are practical limits on the number of individual experiments which can be made. In situations of just such a type, modern statistical methods of planning experimentation and analyzing data have their greatest value. Applications of one such technique, called factorial design, to problems of this type have been described by Dorenfeld and others.'-' The simple factorial design is an efficient procedure when the investigator hopes to provide a comprehensive understanding of the effects and interrelationships of a small number of variables over a limited range. In applied research, this is seldom the main objective. Rather, the investigator usually wishes to determine which of the many potentially important variables are in fact controlling, which levels of the controlling variables will provide opti- mum metallurgical results, and what these results will be at optimum conditions. Interest in detailed trends is limited to the controlling variables and to levels in the region of optimum conditions. Simple factorial design has serious deficiencies for such objectives and is not the most efficient method of experimental design. Deficiencies of Factorial Design In a simple factorial design, an experiment must be made at every possible combination of each level of every variable, once these have been chosen and the levels of each to be included have been decided upon. As the number of variables or levels of each increases, the experimental program quickly reaches prohibitive size. For example, an investigation of only four variables, each at four levels, requires 256 individual experiments. Often upon completion of such an extensive program, it is found that one or more of the variables has metallurgically unimportant effects or that a poor estimate has been made as to the appropriate range of levels to be investigated. The result is that only a small proportion of the data obtained falls in the range of real metallurgical interest. Indeed, it frequently can be anticipated that certain combinations of levels of variables will not produce results of interest, but they still must be included so that the essential balance, or orthogonality, of the design will be retained. It may be true that factorial design will provide the greatest amount of information from a given number of experiments, but it does not necessarily follow that it will lead to the desired information with a minimum number of experiments. Much of the information provided may be of little value. Advantages of Fractional Replication The disadvantages of simple factorial design are overcome to a great extent by a modification known as fractional replication. This is a technique for sampling systematically the potential data of a full factorial experiment, that is, the data which would have been obtained if the complete factorially designed program had been completed. Only a fraction of the total array of experiments is made, but the experiments are chosen in such a way that the important advantages of factorial design and the accompanying analysis of variance are retained. The data obtained from the first group of experiments are used to determine which of several variables are controlling and which levels of these variables are most likely to produce the desired result. Unimportant variables and levels of variables then may be

Jan 1, 1956

By H. R. Banks

PONDERING the action of a ball mill employed to carry on comminution from the product of fine crushing to the point where flotation, cyanidation or other concentrating methods are applicable, one wonders where this machine had its origin. When Henry Wadsworth Longfellow reiterated the observation of that older poet Von Logau, and wrote “Tho’ the mills of God grind slowly, yet they grind exceeding small," he probably visualized the type of mill that was employed in medieval times for the production of flour, and can therefore not be considered as having gained admittance to the fraternity of millmen, on behalf of, either poet. He does, however, make it quite clear that the efficiency of even these Mills of Destiny was low, and to that extent voices a characteristic of fine-grinding equipment that has been the bugbear of all metallurgical engineers. PRINCIPLE OF BALL MILL The principle of the ball mill probably is traceable to the action along the coast line of oceans or lakes, or in the mountain streams. Wave action on rocks and pebbles, close to the shore line, gives the potential energy to the grinding media, which, in their rolling and tossing, break down the sands, and the resultant "pulp" carried out from the shore is classified and settles out in sizes ranging downward to extremely fine mesh. Surely, these are the real mills of God. If we allow our minds to dwell on the total tonnage that has been handled in this way, adding to the sands and clays at present in existence those enormous tonnages of metamorphosed sedimentaries, we sense the vast quantity of rock that has been so reduced. Is it not likely, therefore, that the answer to the beginnings of pebble milling, and eventually ball milling, came through the perception of this natural mill by one of our engineering forebears? METHODS OF GRINDING The relatively low return of mechanical input to a ball mill, in terms of useful work accomplished, has always intrigued me immensely. The potential energy absorbed by a ball raised to a high point in its path is apparently released with a very small return in useful work. Is the ball mill the most desirable means of fine grinding, or is there some other method through which we can recover a reasonable amount of the energy input in terms of useful work? Some years ago, on his retirement, H. W. Hardinge was questioned as to his thoughts on the trend of fine-grinding equipment. As I recall, his prophecy at that time was that the most likely field for improvement in grinding media would be toward a charge of flat disks with some mechanical scheme to cause them to slide over each other. Undoubtedly, Mr. Hardinge went through the usual experience of the muller and bucking board, the customary introduction of the budding millman to his calling. I have often wondered, but have never got beyond the wondering stage, as to the

Jan 1, 1945

By Robert M. Dreyer

AGGREGATE With an annual domestic production of over 1.6 billion tons at a value of over $2 billion (see Table 15.1.1), the production of aggregate (crushed rock, sand, and gravel) is a basic industry of utmost economic importance. Because of the role of aggregate materials as essential ingredients of concrete, asphalt surfacing, and plaster, their delivered prices are major factors in determining the cost of construction. The annual domestic production comes from nearly 10,000 plants. About 15% of these plants account for over one-half the production. In a rapidly inflating economy, the average mine sales price of aggregate has remained relatively stable. The actual mine sales prices, however, vary greatly depending on quarrying costs in various parts of the country. Of much more importance in construction costs, however, is the delivered price of aggregate. This varies for each job, depending on the distance from the quarry and resulting transportation costs, as well as the initial cost at the mine. Because of a proliferation of regulations limiting new quarries in the vicinity of the encroaching urban sprawl, the average distance which aggregate must be transported has been increasing rapidly. Although it is impossible to derive an average delivered cost for aggregate, it should be noted that even an increase of only $1 per ton in average delivered cost over the last decade (probably a minimal assumption) would mean an annual cost $1.5 billion higher than ten years ago. In recent years, structural engineering considerations, as well as an increasing use of lightweight concrete blocks, have resulted in a rapidly increasing demand for lightweight concrete and plaster, the essential ingredient of which is lightweight aggregate. Principal lightweight aggregates are: pumice, slag, perlite (thermally expanded hydrous volcanic glass), vermiculite, and expanded shale, formed by the thermal expansion of shale and slate. The United States now has the capacity to expand, annually, over 13 million tons of shale and slate and to expand over 600,000 tons of perlite. In locating a site for aggregate production. the following factors must be considered: (1) tonnage available; (2) quality of aggregate (including local variations); (3) distance from major use areas; (4) transportation costs, including those resulting from present and possible future haulage restrictions; (5) zoning regulations; (6) operating costs, including the cost effects of compliance with local regulations governing blasting, air pollution, water pollution and drainage, noise levels, and operating periods. At one time, locating a suitable site for the production of crushed rock, sand, or gravel, in most areas, was regarded as an extremely simple task. In the past few years, however, finding a site for profitable production of aggregate has assumed ever-increasing com-

Jan 1, 1976

By Edward Perry

IN the exploration of a copper deposit by drilling, obvious advantages are to be gained from a distinction between primary and secondary ore.1 Perhaps the chief of these is the aid which such a distinction renders in determining where a given hole should stop. The copper assay, often a sufficient guide, cannot always be exclusively relied upon. Primary ores may extend downward indefinitely and may fluctuate in value independently of depth: if primary ores are consistently lean for a considerable vertical distance, there is little reason to expect that, still deeper, they will increase to the commercial grade; on the other hand, rich primary ores may persist uninterruptedly downward or may come in again below a lean interval. Secondary ores, however, have a comparatively limited vertical extent; in a large way enrichment decreases with depth and finally gives out. It follows then, that when a hole descends from profitable ore into ore of less than the commercial minimum, the practical significance of the situation depends upon whether this decrease results from a decrease in secondary enrichment or is a variation in primary content: if the copper of the ore passed through has been chiefly secondary, little is gained in the average case by extending the hole much below the point at which the commercial limit is reached; but, when copper is chiefly primary, due weight must be given to the possibility that, still deeper, the ore may again improve.

Jan 2, 1916

By Robert D. Gunn, John E. Boysen, Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyo., was completed on Jul. 30, 1976. During the experiment production reached 0.32 blm3/d (12 M cu ft/d) of 6.9 w/m3 gas (175 Btu per cu ft). Approximately 6100 tonnes (6700 tons) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, coal gas thermal efficiencies of 76 to 89%, and overall process efficiencies of 65 to 74% were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-74.

Jan 1, 1978

By John C. Draper

The principal object of an underground coal mine transportation sys tem is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside; it must move men in and out of the mine ; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served: 1) Face Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling

Jan 1, 1973

By A. M. Gaudin, S. C. Sun

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

Jan 1, 1967