Search Documents

Jan 1, 1881

Jan 1, 1884

By R. T. Webber, B. B. Owen

THE vapor phase deposition of molybdenum and tungsten from the hexacarbonyls has been thoroughly investigated by Lander and Germer1 and shown to yield well-bonded coatings on a variety of hot metallic surfaces. They also demonstrated that chromium coatings2.3 could be similarly deposited, but did not investigate this metal extensively. Recently,4 conditions have been described by which this compound can be prepared in quantities sufficient for laboratory scale plating experiments, and it is the purpose of the present communication to outline the results of preliminary experiments upon the plating of chromium from its carbonyl. APPARATUS AND TECHNIQUE The apparatus used in these experiments is shown in Fig I. At one end, connected by a short length of rubber tubing, is a Cenco Hypervac 20 pumping continuously. At the opposite end is a needle valve which allows a small stream of purified hydrogen to flow through the apparatus. Connected in series are a trap T1, maintained at the temperature of dry ice and acetone, the plating chamber, and two traps T2 and T3 containing crystals of the carbonyl. T2 is kept in a constant temperature bath (not shown), while T3 is at room temperature. Stopcock S6 allows the hydrogen flow to by-pass the carbonyl traps. A McLeod gauge is connected so that it can measure the pressure at the pump through Ss, or the pressure at the plating chamber through S9 and S6. The standard (12 liter) volume connected by S5 is used to determine the volume included by S4, S6, Se, S10, the needle valve and the McLeod gauge. Knowledge of this volume allows calibration of the flow of hydrogen. The apparatus* is built entirely of pyrex, except for the needle valve, the rubber connection to the Hypervac, and the cover of the plating chamber. The plating chamber is water-jacketed, with a large brass top allowing insertion of the specimen to be plated. Set into the brass top is a ground glass stopper through which thermocouple leads are sealed. The thermocouple wires (pure Pt, and 87 pct Pt-13 pct Rh) serve the double purpose of measuring the specimen temperature and suspending it in the chamber. Surrounding the chamber is the coil of an induction heater, H. The apparatus is designed to allow variation of the following conditions: I, the specimen temperature, from room temperature to about 1000°C, 2, the carbonyl vapor pressure, from 40 to 220 microns, and 3, the hydrogen flow. In several runs, 0.8 to 1.8 pct of hydrogen sulfide was introduced through a needle valve that replaced S4. The vapor pressure of the carbonyl is

Jan 1, 1948

By J. J. Lander, L. H. Germer

MOLYBDENUM and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved only limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150'C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1947

By E. M. Wise

THOUGH known as the platinum-group metal- the sextuplet, platinum, palladium, iridium. rhodium, osmium, ruthenium, might well be called the American metals or perhaps Pan-American metals, as the ore containing them eras first discovered in South America, and in recent years the largest production has come from North America. The South American alluvial deposits, which also, contain gold, are in active production, as are the alluvial platinum deposits of Alaska, but the main production is from the copper-nickel ores of Sudbury, Ontario. The Russian deposits in the Urals were the source of most of the worlds platinum for about 100 years, but since 1934 have assumed second place. For a time considerable amounts of platinum came from several rather rich deposits in South Africa but these were exhausted quickly. However, a tremendous reserve of lower-grade ore exists there, which could be worked profitably if the price of platinum were considerably higher.

Jan 1, 1942

Rustenburg Platinum Mines, Ltd. is the largest producer of platinum metals in the western world. It is also the only major platinum producer this side of the Iron Curtain. One of its mines is situated at Rustenburg, 80 miles northwest of Johannesburg. It also has a smaller operation, the Union Section, 60 miles north of the Rustenburg property. Both mines exploit the Merensky Reef, which forms a part of the Transvaal's remarkable Bushveld Igneous Complex, an irregular oval area covering some 15,000 square miles. In order to cope with an increasing world demand for platinum and such platinum-group metals as palladium, rhodium, ruthenium, iridium and osmium, Rustenburg Platinum Mines embarked on a major expansion program some time ago. It is expected that production will reach an annual rate of 850,000 oz of platinum by the middle of 1969 and increase to 1 million oz by the middle of 1970. Capital expenditures at Rustenburg during the next few years will be about $60 million. It is believed that the ore at Rustenburg averages about 4.5 oz of precious metals per ton. About 70% of the metal is platinum, some 15% is palladium, and the rest is made up of the other metals in the platinum group.

Jan 4, 1969

By R. S. Botsford

SPECULATION as to when and under what conditions mining may be resumed in Russia by foreign interests is becoming more interesting. Circumstances have changed so completely that all new projects must give careful consideration to the conditions as they exist at this time. For example, it is now estimated that a certain copper company in Russia can produce copper and put it on board ship at seaboard for 8 1/2c. per lb., crediting the copper with the value of precious metals contained. It is further estimated that in some places gold can be produced at a cost of about one-half of its value; platinum can be produced even more advantageously. Transportation, which is absolutely necessary for mines of coal, iron or manganese ore, as well as for an industry consuming either coal or coke, is not so essential for the operation of a gold or platinum dredge when the dredge has once been put into operation; after that, food is the principal material for which transportation must be provided. During 1922 the operators in the Urals, who had combined in a so-called platinum trust, expected to produce about 2340 lb. of crude platinum but the amount actually recovered during that season was reported as only 1620 lb., most of which came from hand workings; Nicolo Pavda had the principal dredges in operation during that year. In preparation for 1923 operations, about $400,000 worth of repair parts were obtained in England. At least two American-built dredges and one Putiloff dredge are reported in operation at Nicolo Pavda and it is supposed that most of the better dredges in the platinum district are now working.

Jan 12, 1923

By Patrick H. O’Neill

The Choco placers, mined continuously since the earliest expeditions of the Spanish conquistadors, were exploited by the Indians prior to the conquest. Platinum is found in varying percentages with gold throughout the Choco placers and is found in minor percentages in some placers in other parts of Colombia. The Choco Department is on the west coast of Colombia between the western range of the Andes and the Pacific Ocean and extends from the San Juan River north beyond Panama to the Caribbean. The first reference in European literature to platinum was by Julius Caesar Scaliger in 1557. He did not assign any name to it but referred to it as an infusible metal found in the mines in the New World. The Spaniards had given it the name platina, which is the diminutive for plata, the Spanish word for silver. Don Antonio de Ulloa first recorded the name while on an official visit to the Choco from Spain in 1735.

May 1, 1956

By D. D. Lambert, E. C. Simmons

Rare earth element (REE) analyses of cumulus plagioclase from the PGE ore zone of the Stillwater Complex indicate that pressure fluctuations in the magma chamber acting on a single magma cannot be responsible for features such as the reappearance of Mg-rich olivine on the liquidus. The data are more consistent with a model involving multiple injection and mixing of geochemically distinct magmas. The PGE-bearing sulfides of the J-M Reef are associated with such a reappearance of olivine, indicating that the unusual location of the ore zone may be related to the addition of new magma, compositionally distinct from magmas that produced cumulates in the Ultra- mafic zone of the complex.

Jan 1, 1984

By Herluf P. Nielsen, Robert I. Jaffee

IN recent years much attention has been given to high-melting alloy systems, It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. PAST WORK Müller1 determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from 1771°C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Müller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at 1000°C. Vines and Wise3 report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. MATERIALS The platinum powder used in this work was kindly supplied by the research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio, It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HCI. the resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1948

By N. L. Britton

About two years ago Dr. Newberry referred to me for study a considerable collection of fossil plants sent him by Dr. Arthur F. Wendt, engineer of the silver mines " El Cerro Rico de Potosi" in Bolivia. As I had been interested in working up the extensive accumulations of existing plants made by Dr. H. H. Rusby in the Bolivian Andes further north, and in assisting Dr. Rusby in the study of those now being collected by Mr. Miguel Bang in other parts of that country, I was glad of an opportunity of ascertaining something of the Tertiary flora of the region. I was unable to take up the subject at that time, but have since been able to conclude the investigation, and the results are here presented. At a time when the mineral resources of the Southern States are attracting such widespread interest and attention, I have thought it appropriate to give a short general description of the iron-ore deposits of a territory concerning which little is as yet known and nothing published, so far as I am aware. The data used here are due to the preliminary examinations of the North Carolina Geological Survey, on which work I was engaged during the past summer, and my acknowledgments are due to Prof. J. A. Holmes, State Geologist, and Messrs. Harris, Ashe, and Lewis, of the survey, for their co-operation in the work; also to Messrs. A. S. McCreath and C. B. White for analyses which they Kindly furnished. Other analyses were made by Mr. Charles Baskerville, assistant chemist to the survey, and this may be understood where the name of the chemist is not mentioned. All samples for analysis were dried at 212' F. The accompanying map has been prepared from the revised sheets of the United States Geological Survey by Mr. H. L. Harris, and will be referred to throughout this paper. Ashe county lies in the extreme northwestern part of North Carolina, bordering on Tennessee and Virginia; it is drained principally by the north and south forks of New river and their tributaries, and is therefore on the eastern edge of the great Mississippi drainagebasin. The country is exceedingly rugged and mountainous, having an average elevation of about 2900 feet above sea-level. Jefferson, the county seat, near the center of the county, is 45 miles nearly due south from the Norfolk and Western R.R. at Marion, Va., and 30 miles northwest from the Richmond and Danville R.R. at Wilkesboro, N. C. Geologically the ore-deposits described in this paper are situated in the area of the crystalline rocks, consisting chiefly of gneiss, hornblende-schist, and micaceous schists.

Jan 1, 1893

By Gregory B. Baecher

Rock engineering involves uncertainties which are large and difficult to quantify. The traditional design approach to these uncertain- ties has been conservatism, and has been satisfactory to the extent that failure rates are reasonably small. Yet, a price is paid for conservatism, and that price is not always small. Today, reliability and risk analysis are finding use in rock engineering. The introduction of such methods, usually under the name 'probabilistic design,' is controverisal. However, if the jingoism of both sizes in this controversy is stripped away, it appears that new insights about uncertainty in rock engineering are emerging.

Jan 1, 1982

By Paul M. Tyler

FOR the same reason that water is not missed until the well runs dry, the roles of many industrial minerals in wartime are often overlooked. In contrast to the growing shortages of many metals, our supplies of most nonmetallic minerals are limited only by our machinery for taking them from the ground and by our processing facilities. With few exceptions, the demand for increased supplies has been met without fanfare or delay. Only Brazilian quartz crystals, certain kinds of mica, and, latterly, industrial diamonds are on the so-called strategic list, although asbestos, beryl, corundum, cryolite, fluorspar, crucible-grade graphite, ilmenite, iodine, kyanite, monazite, nitrates, rutile, and zircon have caused more concern among those responsible for procurement and are included in our preclusive buying programs. Such specialties are needed urgently, but they are far less important in the over-all picture than the more abundant minerals.

Jan 1, 1942

By JOHN R. SUMAN

OVERWHELMING proof of the importance of oil in a modern national economy is afforded by the present European War. Treat¬ies and national boundaries have been cynically violated to secure greater supplies of the precious fuel. Petroleum substitutes have been desperately, and far from successfully, sought. The whole German military theory of the drang nach Osten, the drive to the East, is directed at cutting the British supply of oil and securing a supply for Germany. This is a war of machines, and the machines of war feed hungrily on oil. In view of this fact, it is surely comforting to know that we are living today in a nation which has surpassed all the rest of the world not merely in unearthing the raw supplies of petroleum which lie beneath its surface but also in every phase of the industry in mining, refining, processing, production, and distribution.

Jan 1, 1941

By George E. Erdman

Gouverneur Talc Co. had sought an effective means of depicting its mine at Balmat, N. Y. since it commenced operations in 1947. After considerable research the engineering department settled on the idea of a model made of plexiglas at a scale of 1 in. to 50 ft. The solid portion of this model represents the actual underground excavations. Talc is mined from two metamorphic tremolite-talc orebodies which are part of a complex fold system in this region. In the mine, stopes are laid out in panels and developed into openings 50 ft wide, 10 to 80 ft high, and perhaps 200 ft in length. Pillars usually approximate 30 ft in width. All present mining operations are contained within a block 2000 ft long, 1700 ft wide, and 1500 ft thick.

Jan 11, 1960

By F. J. Escandon V.

The Plomosas stratiform lead and zinc deposits are located in northeastern Chihuahua in a sequence of folded Paleozoic and Jurassic rocks. They consist mainly of channel or blanket-like bodies of ellipsoidal cross section restricted to a 60-in-thick shaly limestone and a 30-m-thick marble horizon of La Casita formation, with some reemplacement veins and shoots within the Plomosas formation. The mineralogy consists of iron-poor sphalerite, galena with a small silver content, and pyrite, in a gangue of calcite, barite, and minor quartz. The ore bodies present a lateral zoning with zinc-lead ratios increasing to the northwest. Vertical zoning shows marked changes in zinc-lead ratios and in the width and tenor of the ore which cannot be related to sedimentary or diagenetic features. Transgressive mineralization and some small fissure veins and breccia pipes also point to an epigenetic origin. Sulfur isotope analysis and geochemical data indicate hydrothermal solutions. Texture of the ores in the Mina Vieja marble is coarse, but in the Cuesta shale it is banded along bedding. The low iron and silver content of the sphalerite and galena and the weak hydrothermal alteration (only marbleization) of the wall rock suggest a telethermal stage of the solutions. There is no evidence of a possible intrusive rock mineralization.

Jan 1, 1976

By Cheri Eby, William R. Eby

INTRODUCTION Pneumatic conveyance systems provide for material placement at high compaction rates in confined spaces. This method of conveyance provides proper roof support and ground stabilization important to underground mining activities. Today underground mining activities are conducted far differently than those of our ancestors, in that the reclamation process is the final step in any mining activity. Responsible mine owners are constantly seeking innovative methods to assist them in their reclamation procedures. During the last few years, particular attention has been paid to previously mined areas, as many of these abandoned areas lay open, imposing a constant threat to humans and animals. Considerable attention is being directed to applying proper methods for the filling and sealing of underground slopes, drifts, tunnels, and adits, because today we are experiencing the effects of past mining activities such as subsidence, acid mine water run-off, buring refuse piles, and underground mine fires. Furthermore humans and animals who have ventured into abandoned mine openings have died from exposure, suffocating gases, and mine collapse. This paper explains the method of pneumatically filling and sealing these openings and underground works by means of employing pneumatic equipment and proper backfill material together, thus achieving high material compaction and thereby providing the complete filling of the voids and alleviation of the mentioned dangers. NEUMATIC SYSTEMS The use of air to transport material is widely used; however, conveying abrasive material (e., rock, earth, and cement) requires certain pneumatic transport systems designed to handle the abrasiveness as well as the size of these materials. The Eby pneumatic transport sys tem, known as a Mobile Stower, in mounted on a 42-foot trailer pulled by a Kenwor th tractor. This arrangement allows for quick mobilization and project set-up. The pneumatic system, composed of several components assembled together, produces the volume and pressure of air required to transport the material. Knowledge of elevation, ambient temperature, and material composition at the locations to be backfilled play a big part in the design and useage of the pneumatic system. In this particular system design, material is placed by a front-end loader into an eight (8)-yard hopper which is located over a belt conveyor. The conveyor transports the material up to an air lock feeder, which is the metering devise used to feed the material into the Tee Injector located directly below. Air is supplied by a positive displacement blower which, in this instance, delivers up to 4400 CFM's of air at 8 to 12 PSI. Horse power requirements to drive the blower are met with the useage of either a diesel engine or an electric motor. A diesel engine enables the Mobile Stower to operate in remote areas. As the air flows through the upstream air piping, it passes through the Tee Injector and picks up the material and conveys it through the material conveyance pipe, (referred to as down-stream pipe), and out the placement nozzle. Depending upon material composition and the amount of tonnage to be moved, either mild carbon steel pipe or specially heat- treated hardened pipe is used for the material conveyance line. The entire pneumatic system is controlled from the operator's console. With the aid of instrumentation, only one person is required to operate the system. Tonnage rates vary in accordance with horse power and air supply, as well as

Jan 1, 1982

By E. C. Carris

THE particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 12,000,000 tons of bituminous coal were cleaned by air machines during 1940.They have not found any application for cleaning anthracite. Since the development and introduction of the first successful commercial pneumatic oscillating machine for cleaning bituminous coal in 1916, by the Sutton, Steele and Steele Co., Dallas, Texas, and the American Coal Cleaning Corporation, formerly of Welch, W. Va., four other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine, 1924. 2. Arms "Concentrator," oscillating table, 1924. 3. Hey1 and Patterson oscillating table, 1927. 4. "Stump Air-Flow," pulsating air jig, 1932. Out of these five developments only the Sutton, Steele and Steele, or American Oscillating, and the Stump Air-Flow Jig remain on the market. They are the predominating pneumatic coal-cleaning machines in use in the United States. HISTORY OF AMERICAX TYPE SEPARATOR The first successful American machine, the CJ table (Fig. 1) was developed by the Sutton, Steele and Steele Co. The SJ table was the first standard model designed specifically for the cleaning of coal. It was installed in the original Crane Creek plant, owned and operated by the American Coal Co. at McComas, West Virginia. This plant was designed by The Roberts and Schaefer Co., Chicago, Ill., working in cooperation with the American Coal Cleaning Corporation, which had taken over the patent rights and sale of the pneumatic separators. Eight machines were installed in this plant. They were known as the type SJ. They were 60 by 84 in., the short dimension being the width of

Jan 1, 1943

By E. C. Carris

THE particular field of application of machines utilizing air cur¬rents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 12,000,000 tons of bituminous coal were cleaned by air machines during 1940. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful com¬mercial pneumatic oscillating machine for cleaning bituminous coal in 1916, by the Sutton, Steele and Steele Co., Dallas, Texas, and the Ameri¬can Coal Cleaning Corporation, formerly of Welch, W. Va., four other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine, 1924. 2. Arms "Concentrator," oscillating table, 1924. 3. Heyl and Patterson oscillating table, 199.7. 4. "Stump Air-Flow," pulsating air jig, 19391. Out of these five developments only the Sutton, Steele and Steele, or American Oscillating, and the Stump Air-Flow Jig remain on the market. They are the predominating pneumatic coal-cleaning machines in use in the United States. HISTORY OF AMERICAN TYPE SEPARATOR The first successful American machine, the CJ table (Fig. 1) was developed by the Sutton, Steele and Steele Co. The SJ table was the first standard model designed specifically for the cleaning of coal. It was installed in the original Crane Creek plant, owned and operated by the American Coal Co. at McComas, West Virginia. This plant was designed by The Roberts and Schaefer Co., Chicago, Ill., working in cooperation with the American Coal Cleaning Corpora¬tion, which had taken over the patent rights and sale of the pneumatic separators. Eight machines were installed in this plant. They were known as the type SJ. They were 60 by 84 in., the short dimension being the width of

Jan 1, 1943

By David R. Mitchell, E. C. Carris

THE particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of fine sizes of bituminous coal. Approximately 18,000,000 tons of bituminous coal was cleaned by air machines in 1947, but such machines have not yet been applied in the cleaning of anthracite. This chapter is limited to a description of the processes in which the separation between coal and refuse depends mainly on a difference in specific gravity. Dry processes depending on differences in coefficient of friction, shape, or other property, are described in chapter 17. The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. Some of these early machines are described by Berrisford,1 Chapman and Mott,2 and Mitchell.3 Only two machines are extensively used today in the United States, the Stump air-flow jig and the American oscillating table. GENERAL CHARACTERISTICS OF AIR CLEANING MACHINES The principles of gravity concentration and the properties of air as a medium for separation were explained in chapter 9. It was pointed out that because of the low density of air a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. It was also noted that the compressibility of the air may cause "geysering" of the bed and disturbance of the hindered-settling classification if the correct balance of conditions is not maintained. Most devices use a vertical upward current of air through the bed of material. They differ by the method of imparting mobility to the bed and the method of removing the refuse. In general terms, the air machines can be divided into three types: 1. Pneumatic jigs where the air current is pulsated. 2. Pneumatic tables where the refuse is diverted from the direction of flow of the clean coal by a system of riffles fixed to the deck.

Jan 1, 1950