Search Documents

By Winston A. Wong, John J. Jonas

Commercial purity aluminum was deformed by extrusion over the temperature range 320° to 616°C and the strain rate range 0.1 to 10 per sec. Flow stresses and strain rates were calculated from the experimenLa1 ram pressures and speeds. The stress-strain rate-lemperature relationship in extrusion was found to be similar to that in creep. Extrusion, torsion, compression, and creep data extending over ten orders of magnitude of strain rate and over two orders of magnitude of stress were correlated by a single creep equation. It was concluded that hot-working is a thermally activated process, in which the rate-controlling mechanism is either the climb of edge dislocations or [he motion of jogged screw dislocations. The microstructural changes observed during extrusion were consistent with the proposed deformation mechanisms. ALTHOUGH great progress has been made in understanding the technology of extrusion, very little is known about the actual deformation mechanisms operating during flow. Previous accounts describing extrusion have indicated that the relationship between ram speed (V), pressure (P), and temperature (T) can be given as follows:1 V = apb and P = A' exp(-AT). In these equations, a and b are constants which depend on temperature, A' is a constant which depends on ram speed, and A is a "coefficient" with a different value for each metal. Although these equations have fairly wide application, they do not contribute much to a fundamental understanding of the deformation. Furthermore, extrusion has not hitherto been considered as a thermally activated rate process. This lacuna is surprising because hot-working is similar to high-temperature creep in several respects. There is, in fact, a fair body of experimental evidence suggesting that the material response under hot-working conditions is similar to that occurring under creep conditions, in spite of the many orders of magnitude difference in strain rate.2"4 Since creep has been extensively analyzed in terms of dislocation mechanisms, the comparison of hot-working to creep is useful, for it can suggest the possible deformation mechanisms operating during hot-working. In this paper, the hot extrusion of aluminum will be examined from the point of view of thermally activated deformation mechanisms, such as operate during creep. EXPERIMENTAL PROCEDURE The experimental procedure consisted of extruding commercial purity aluminum* over a range of ram velocities and temperatures at constant die reduction by the direct method. Details of the experimental equipment have been published elsewhere.5 Extrusion was carried out at each of the following billet temperatures: 320°, 376°, 445°, 490°, 555°, and 616°C at the following constant ram speeds: 0.002, 0.008, 0.02, 0.1, and 0.2 in. per sec.* All results were obtained using a square-shouldered die with an extrusion ratio of 40:1, giving a reduction in area of 97.5 pct. The ram force was the dependent variable, and was measured by means of strain gages on the ram and was plotted as a function of ram travel. The sequence of events before making an extrusion was duplicated before each run so as to minimize as much as possible variations in experimental conditions. For example, after the equipment had been assembled, the billet was allowed to heat up to temperature inside the insulated container. Once the container attained the desired temperature, a period of 1/2 hr was allowed to elapse before the extrusion was made. This time was found to be required to allow the billet to reach a steady-state temperature, as determined from previous tests. When all was ready, extrusion was carried out without interruption; that is, the billet was upset and extruded in one operation. EXPERIMENTAL RESULTS AND DISCUSSION The two usual experimental approaches for investigating high-temperature deformation exhibit an important common feature. In the first approach, which corresponds to creep, a constant stress (or load) is applied to the material at constant temperature and the resultant strain is recorded against time. After an initial transient stage, a state of constant strain rate exists (secondary creep), in which a steady-state condition is established which is sensitive to variation in either applied stress or temperature. In the second approach, a constant strain rate is applied and the resultant flow stress is recorded. This corresponds to the situation in hot torsion or hot compression, where it is observed that, for a constant test temperature, there is an initial rise in stress to a steady value which is maintained up to very high strains. In tests of this type, a steady-state region is also established in which the stress is sensitive to variation in either the strain rate or the temperature.3,4,6-16 In both types of tests, therefore, a steady-state region is established after an initial transient. In the case of hot-working this region may be called steady-state hot-working, and it is analogous to steady-state creep with which it has many common features. Stress Dependence of the strain Rate in Extrusion. In order to assess the stress dependence of the strain rate under extrusion conditions, and to compare it to that of creep, as well as of hot torsion and hot compression, the extrusion data were analyzed according to power, exponential and hyperbolic sine creep equations.

Jan 1, 1969

By Michael Epstein, Daniel E. Rosner

Fume nucleation sufficiently close to vaporizing suvfaces can augment net vaporization rates into cooler environments. Environmental conditions favoring large vaporization rate enhancements are briefly discussed and a previous theoretical treatment of this nucleation phenomenon is generalized to account for the self-regulating effect of condensalion-heat release within the boundary layer. Despite kinetic limitations on homogeneous nucleation, and latent heat release, non-diffusive condensate removal processes appear to make possible large enhancements in steady-state vaporization rates, provided surface temperatures are well below the boiling point. When condensed phases vaporize (or dissolve) into cooler media, the diffusion-limited mass loss rate can be strongly influenced by the process of nucleation/con-densation (or precipitation) within the thermal boundary layer. This condensation process (which typically leads to mists or fumes in the case of evaporation into cooler gases) has the effect of steepening the vapor pressure profiles near the evaporating surface, since the condensation zone acts as a vapor sink. However. the resulting enhancement in the diffusion-limited evaporation rate can be estimated (as first done by Turkdogan1 for the case of molten iron/nickel alloys evaporating into helium) only if one has independent knowledge of the critical supersaturation, sCrit(T), required to homogeneously nucleate the vapor.* In a recent reformulation and generalization of the theoretical model of Ref. 1 it has been shown that, when log sCrit is approximately linear in reciprocal temperature, rather simple expressions can be derived4 for the ratio of the actual rate of vaporization j" to either the minimum (no condensation) rate j"min, or the maximum (equilibrium condensation) rate j"max In the present communication we wish to briefly report on further developments and implications of the formulation of Ref. 4, with emphasis on i) environmental conditions favoring large enhancements in vaporization rate, and ii) the self-regulatory influence of condensation heat release (neglected in Refs. 1 to 4) on predicted vaporization rates. Additionally, we take this opportunity to correct several misprints appear- ing in Ref. 4, and comment on Elenbaas's recent criticism5 of Ref. 1. MAXIMUM POSSIBLE VAPORIZATION RATE IN PRESENCE OF CONDENSATION A nonequilibrium theory is of interest because of the very large difference between the minimum (no condensation) and maximum (equilibrium condensation) vaporization rate. The magnitude of this maximum possible enhancement can be shown quite clearly by combining a result of Refs. 3 and 4 with the fact that for most liquids there is a simple relationship between the molar heat of evaporation, A, and its boiling point, i.e., A/(RTBp) = C, where the constant C, often called the Trouton ratio, takes on values not very different from 11.* More generally, for any substance (including The Trouton ratio (which for water is 13, for methane, 10, and so forth) will be recognized as the ratio of the molar entropy change upon vaporization (at TBP or Ttransf) to the unlversal gas constant R. Its near constancy reflects the fact that the change in atomic order upon vaporization depends only weakly on the kinds of molecules involved. those that sublime under ordinary conditions) we can define a characteristic transformation temperature. Ttransf, by a relation of the form Ttransf =A/(CR), and then examine the maximum possible evaporation rates as a function of how far removed from Ttransf are the surface temperature, Tw, and ambient temperature, T. Subject to the assumptions: 1) equilibrium vapor pressure, pv,eq, everywhere small compared to prevailing total pressure, p, and 2) negligible effect of condensation heat on temperature profile, the maximum enhancement ratio was found (Eq. [17], Ref. 4) to be: where, for most vapors, Nu/NuD (the ratio of heat transfer coefficient to mass transfer coefficient for the same configuration) is a number near unity.* Ex- *An alternative derivation of the Nu = NuD special case of this equation. revealing its validity for arbitrary velocity/temperature profiles in a laminar boundary layer, is given in Ref. 3. amining this result for a "Trouton substance", one obtains the results shown in Fig. 1, constructed for C = 11. Since we are concerned with vaporization enhancements (j'max/J"min > 1) at surface temperatures below Ttransf, this area of interest is shown unshaded. One notes that at a fixed ambient temperature (hence, T/TtranSf) there is a unique surface temperature, 2T , at which j"max/j"min attains its peak value; moreover, the peak enhancement ratio, see dashed locus. Fig. 1, is: (NuA/NuD)(C/4)(Ttransf/T,). Hence, if Nu = NuD, when the ambient temperature is less than 1/4 of TtranSf the peak enhancement exceeds the Trouton

Jan 1, 1969

By E. Breinan, M. Salkind

Al3Ni whiskers were chemically extracted from unidirectionally solidified Al-A13Ni eutectic ingots, bent into loops, and heated for 0.1 to 10 hr at 320°, 415", and 510°C. The initial strains ranged from 0.003 to 0.055. In all cases, permanent plastic deformation was noted after heat treatment. The deformation consisted of relatively uniform bending at low stresses and temperatures and short times and kinking followed by fracture at high stresses and temperatures and long times. After kinking, the whisker segments adjacent to the kinks were found to have straightened, which is evidence of a dislocation condensation mechanism. The range of temperatures and strains at which time dependent plastic deformation was found indicates that creep of whiskers probably plays a role in the creep of A13Ni whisker-reinforced aluminum. WHISKERS may be defined as nearly perfect single crystals which exhibit high strength. Because they can support high stresses at relatively low strains, they have been successfully employed in reinforcing metals at both ambient and elevated temperatures. In studying the creep behavior of A13Ni whisker-reinforced aluminum at elevated temperatures,1,2 it was noted that the composites exhibited measurable creep deformation. This investigation of the creep relaxation of individual A13Ni whiskel, extracted chemically from the composite was initiated to determine if creep of whiskers could con. "bute to the overall creep of the composite material. Many observations of plastic deformation of metal and halide whiskers have been made. Brenner3-8 noted that copper, silver, and iron whiskers exhibited heterogeneous plastic deformation at room temperature when strained beyond their yield points. Gyulai9 and Gordon10 observed plastic deformation of relatively large (>3 µ) NaCl and KC1 whiskers, although the smallest, most perfect whiskers were completely elastic. Eisner" noted plastic deformation and microcreep of iron and silicon whiskers at room temperature after straining beyond the yield point. Whiskers reported to exhibit creep at stresses below the yield point were zinc1'-" and Silicon.15 Cabrera and price" observed some zinc whiskers which crept at room temperature after a short incubation period but then stopped creeping after a short time. Because some of their specimens exhibited no creep, they concluded that those whiskers that crept were relatively imperfect. Pearson, Reed, and Feldman15 observed similar creep behavior of silicon whiskers at 800°C. They also concluded that creep of the whiskers was a result of imperfections in their crystals. Brenner16 observed delayed failure of A12O3 whiskers at elevated temperatures but found no evidence of plastic deformation up to 2030°C (99 pct of E.EREINAN and M.SALKIND,JuniorMembers AIME,are Research Scientist and Chief, respectively, Advanced Metallurgy Section, United Aircraft Research Laboratories, East Hartford, Conn. Maunscript submitted April 5, 1968. IMD the melting temperature). Brenner also noted7 that some copper and iron whiskers exhibited delayed kinking above 350°C while others did not. One can conclude from these observations that small relatively perfect whiskers could exhibit completely elastic behavior during sustained elevated-temperature loading of composites. Since A13Ni whiskers tested in both bending and tension were found to exhibit no evidence of plastic deformation at room temperature'7'18 this study was initiated to determine whether or not creep of A13Ni whiskers occurred at the elevated temperatures at which creep in the composites was observed. Whiskers were chemically extracted from ingots of unidirectionally solidified A1-A13Ni eutectic, constrained in bending to various elastic strains and heat-treated. The bending constraints were removed after heat treatment and the amount of permanent set was taken as a measure of the time-dependent plastic deformation. EXPERIMENTAL PROCEDURES Ingots of eutectic Al-A13Ni containing nominally 6.2 wt pet Ni were unidirectionally solidified at approximately 11 cm per hr using a process described elsewhere.19,20 The starting materials were 99.99 pct pure. Cylindrical sections cut from the center of each ingot were placed in a 3 pct aqueous solution of hydrochloric acid and the whiskers were extracted as described previously.17 The whiskers nearest the surface were blackened somewhat due to overexposure to the acid while the center of the ingot was being dissolved These partially attacked whiskers were discarded. An intermediate zone of silver-gray-colored whiskers was collected and stored in methanol for use in relaxation experiments. Individual long pieces of A13Ni whiskers were placed on Fisher Precleaned Microscope Slides. These normally straight whiskers were bent elastically into arcs or loops of varying radii by manipulating their ends with a slender probe. The mass attraction between the whisker and the probe was sufficient to cause the whisker to follow the probe. The whiskers were retained in the elastic bend by the surface tension of a fine residual film on the slides. By using long whiskers, the action of the surface tension on the unlooped ends of the whisker allowed high elastic strains to be maintained in the loops. After each whisker was bent, a photomicrograph was taken for use in measuring the bending strain. The range of strains studied was 0.003 to 0.055. The bent whiskers were then encapsulated in Pyrex tubes at pressures between 10"6 and 5 x 10"6 mm of mercury and heat-treated at 320°, 415°, and 510°C (respectively 53, 61, and 70 pct of the peritectic decomposition temperature). After each heat treatment, the liquid film on the slides was found to have dried, but the whiskers were held in their original shapes by a residue on the slide. The minimum radius of curvature of each bent whisker was measured before and

Jan 1, 1969

By A. Gemperle

Electron diffraction and transmission electron microscopy on foils at room temperature were used to investigate the ordering of Fe-Si alloys containing 10 to 23 at. pct Si. A certain degree of DO3 order was found in all alloys. With the exception of the lowest silicon concentration for which the antiphase domains could not be clearly resolved, the alloys have a domain structure of two-domain type with boundaries having 1/4a01<111> displacement vectors for less than 12.3 at. pct Si and with boundaries having 1/2 a0<100> displacement vectors for more than 12.3 at. pct Si. The alloys with 12.3 at. pct Si have a domain structure consisting of fine domains with 1/2a&apos;o<100> boundaries within much larger domains with 1/4a&apos;o<111> boundaries. The development of these structures can be explained by transition of the alloy from the disordered state into the B2-type order and then into the D03-type order by the mechanism proposed previously for the FeSAl alloys. The existence of the B2 structure in the lower part of the investigated concentration range reported in some articles can be explained by fine domains with 1/2a&apos;o<100> boundaries formed by several disordered planes within large domains with 1/4a&apos;o<111> boundaries. The ordered structure predicted by the theory —with practically no domain boundaries —is found in the alloys having 12.3 at. pct Si where it develops in the B2 structure region. ORDERING in Fe-Si alloys was first studied by phragmenl who found that beginning with 13 at. pct Si the DO3 (Fe3Si) superlattice reflections appear in the diffraction patterns. The equilibrium diagrams constructed later by corson2 and Haughton3 from various measurements proposed the existence of a homogeneous solid solution (a phase) in the range from 0 to 25 at. pct Si. Jette and Greiner4 and Farquhar et al.5 measured the relation between lattice parameter and composition and they considered the break in the curve at 9 to 10 at. pct Si to be caused by the ordered solution a"(Fe3Si). Glaser and Ivanick6 Determined critical ordering temperatures of the alloys containing from 10.9 to 27.9 at. pct Si from the measurement of the electric resistivity of quenched samples. In all cases the critical temperature was lower than the melting point and it was highest for 25 at. pct Si. Lihl and Ebel7 measured the lattice parameter curves at various temperatures up to 1000°C. The region between two breaks on these curves, corresponding to 10 to 12.5 at. pct Si at room temperature, was considered by them to be two-phase (a + a"). They concluded by extrapolation of the measured values that a" in the alloy having 25 at. pct Si is stable up to the melting point. Davies8 studied superlattice reflections in the X-ray diffraction patterns of an alloy containing 8.7 at. pct Si. He found the B2 structure and short-range order in the slowly cooled samples and the DO3 A. GEMPERLE is Research Scientist, Institute of PhysicS, Czechoslovak Academy of Sciences, Prague, Czechoslovakia. __Manuscript submitted January 2, 1968. IMD structure in the quenched and annealed samples. This investigation first reports the presence of the B2 structure, phase a&apos;: in Fe-Si alloys. Meinhardt and krisement9,10 also found its existence in Fe-Si alloys by neutron diffraction. No order was detected by them in the alloy containing 8 at. pct Si. The onset of B2 order was observed at a composition of 9.2 at. pct Si. They found almost perfect B2-type order with partial DO3-type order at room temperature in the 10 to 12.5 at. pct Si range and almost perfect DO3-type order in the 12.5 to 25 at. pct Si range. They established the critical temperatures Tc of both the structures through measurement at higher temperatures. The critical temperature for the B2 structure was found to be always higher than the critical temperature for the DO3 structure of the same alloy. They extrapolated the curves of the critical temperatures and concluded that the alloys with more than 17 at. pct Si have the B2 structure up to the melting point and the alloys with more than 23 at. pct Si have the DO3 structure up to the melting point. The results of Meinhardt and krisement9,10 were confirmed by Dokken&apos;s measurement" of the temperature dependence of the electrical resistivity in the 10.8 to 15 at. pct Si range. On the other hand chessin12 detected by X-ray diffraction a considerably lower degree of order in the 12.7 at. pct Si alloy. ANTIPHASE DOMAIN STRUCTURE IN ALLOYS WITH B2- AND DO$-TYPE ORDER The ordered structures B2 and DO3 can be described in terms of a subdivision of the bcc lattice into four fcc sublattices with a parameter double that of the bcc lattice. Following Marcinkowski13 we will label them I. 11, 111, IV. The B2 structure in the AB alloy is formed by placing A atoms on sublattices I and II and B atoms on sublattices III and IV. In a non-stoichiometric perfectly ordered alloy having concentration (A) > (B), A atoms occupy sublattices I and 11. and A and B atoms distributed at random occupy sublattices III and IV. The DO3 structure in an A3B alloy is formed by placing A atoms on sublattices I, 11, and 111, and B atoms on sublattice IV. In a nonstoichiometric, perfectly ordered alloy having concentration (A)/3 > (B), A atoms occupy sublattices I, 11, and 111, and A and B atoms distributed at random occupy sublattice IV. As further shown in Ref. 13, two types of domains are possible in the B2 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4 a&apos;o<ll1> only. Four types of domains are possible in the DO3 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4a&apos;o<111> and 1/2a&apos;o<l00>. Bethe14 suggested on the basis of theoretical considerations that in a structure with two sublattices at low temperatures only one domain should be present in the whole crystal at equilibrium. Similarly Bragg15 concluded that at low temperatures the domain struc-

Jan 1, 1969

By M. Metzger, L. E. Hendrickson

Grain boundary attack in 16 pct HCl was found to be substantially the same at low penetrations in zone-refined aluminum (individual impurities 0.1 at. ppm), superior electrolytically refined aluminum (51 at. ppm), and aluminum with various impurities at much higher levels. It was concluded that impurity atom segregation affecting corrosion would have been detected and that the corrosion susceptibility did not originate in this segregation but in the structure of the boundary. It was pointed out that the significance of most previous studies in this system had been obscured by an unrecognized autocatalytic copper reaction. Although general corrosion rate was also impurity-insensitive , there was shallow pitting attributed to iron seg-regation and a hillocked surface texture associated with copper; these were interpreted as due to cathodic damage affecting- cathode distribution. THE grain boundary corrosion suffered by high-purity aluminum in hydrochloric acid has been the object of some interest (the earlier work is summarized in Ref. 1). The central metallurgical question here is whether the corrosion susceptibility of a boundary originates in its structure or in impurity atom segregation. An attempt to study this question revealed large catalytic effects associated with small quantities of the copper impurity in the aluminum, 220 ppm, or in the corrodent, and these magnified the preferential boundary attack and obscured the intrinsic susceptibility question.&apos; After the catalytic effects had been examined,"&apos; test conditions could be designed to avoid them and methods developed for studying the shallow boundary penetrations prevailing when they were absent.= It then became possible to determine whether intrinsic boundary corrosion in aluminum involves impurity segregation. The older work provided no firm information on grain boundary segregation of specific solutes influencing corrosion although several studies suggested iron segregates.4,5 perryman4 found in 10 pct HC1 that the slowly developing (microns per month) grain boundary grooves were deeper in material of higher iron content (range 10 to 550 ppm, with 5 to 80 pprn Cu) but he did not measure the depths of general corrosion, which were probably several times greater, and his reference surfaces may have varied more than did the groove depths. Metzger and Intrater&apos;s results for 20 pct HC~,&apos; which yielded higher time-average rates (mm per month) and deeper penetrations, suggested that boundary segregation of iron (range 4 to 230 ppm, with 22 pprn Cu) decreased the penetration rate. However. in the stronger acid the autocatalytic l.E. HENDRICKSON, Student Member AIME ,and M. METZGER, Member AIME, are Research Assistant and Professor of Physical Metallurgy, respectively, Department of Mining, Metallurgy and Petroleum Engineering, University of Illinois, Urbana, Ill. Manuscript submitted March 11, 1968. IMD effect of the copper impurity is greater1,2 and it is now evident that their corrosion rates had been much magnified by this effect and did not provide a proper basis for the analysis of segregation. In exploratory studies of other solutes (made under the same conditions), 1000 ppm additions of Mg, Mn, or Si or 100 ppm Ca were without effect.1 Montariol6 noted that boundary attack in 22 pct HC1 persisted after zone refining although with fewer deep fissures (ranges 0.06 to 4 ppm Cu, 4 to 23 ppm Fe). Autocatalytic effects may have influenced these results also and those of Perryman.4 The present objective was, as a first step, to see whether quantitative tests designed to exclude autocatalytic influences would indicate the existence of low-level impurity effects on intrinsic boundary corrosion. Comparison of electrolytically refined with zone-refined aluminum of lower copper and iron contents revealed no differences in boundary corrosion, but certain impurity-sensitive differences in general corrosion morphology were noted and investigated further at higher impurity levels. I) EXPERIMENTAL PROCEDURE A) Material. A selection from commercially available material was made with the cooperation of several producers. An electrolytically refined lot (III-A, 1 ppm Cu, 2.4 ppm Fe) studied previously3 provided a starting point. Since material of substantially higher copper content could not be used if the autocatalytic corrosion reaction were to be avoided,2,3 a lot (III-B) of about the same purity was added as a check, two zone-refined lots (I-A and I-B) with copper and iron an order of magnitude lower were selected for comparison, and an intermediate lot (11) was included. Analytical data are given in Table I. For copper in I-B and iron in I-A and I-B, the actual concentration is thought to be near the limit given, i.e., about 0.1 ppm. For titanium, vanadium, and chromium in III-B, the actual amounts are thought to be, like those in III-A, substantially lower than in the zone-refined lots (these elements concentrate in the solid on freezing). Data are given later for some additional lots surveved. B) Specimen Preparation and Procedure. one by 3 cm blanks with a notched stem were cut from 1-mm cold-rolled sheet, annealed 24 hr in air at 650°C, and quenched in an air stream (42°C per sec initial cooling rate, 100 sec to cool to 100°C). The high annealing temperature maximized diffusivities and approach to equilibrium impurity distributions. A water quench, in principle more efficient in preserving the distribution established, was undesirable because the boundaries were almost plane and they tended to shear and migrate during the quench and thus to be separated from any existing impurity atmosphere. Test procedures, previously described,3 involved electropolish-ing, etching 2 min in 10 pct HF at 24.0°C, and expos-

Jan 1, 1969

By N. N. Breyer, W. R. Warke, S. Dinda

A model for the low-temperature peak, LTP, in fcc metals is presented. In high stacking fault energy metals, e.g., aluminum and nickel, it is proposed that a reversible dislocation glide and climb process might give rise to the observed high relaxation strengths and activation energies equivalent to volume self-diffusion values. In low stacking fault energy metals such as copper, gold, and silver, dislocation climb is energetically unfavorable at T < 0.5 Tm and the relaxation process is therefore mainly one of reversible glide. This model is used to explain the effect of a change in grain size and impurities on the LTP. THE low-temperature grain boundary damping peak, LTP, in spectroscopically pure aluminum,&apos; copper,17&apos; gold,2 nickel,3 and silver4 has recently been the subject of a detailed investigation by our laboratory. The main results are summarized in Table I. An empirical relationship was found between the peak relaxation strength, AE, and the width of the dissociated dislocation, do,* given by: do = µa2/24p? (Ref. 5) [I] where p is the shear modulus, y is the stacking fault energy,6-8 and a is the lattice parameter, Table 11. 4E is plotted against do in Fig. 1. Two regions are apparent: region (a)! which contains all but one of the metals, where AE decreases linearly with increasing do, i.e,, AE 1/do; and region (b), where ?E is approximately independent of do. A similar trend is observed when the ratio Qp/QL is plotted as a function of do, Fig. 2. (Qp and Ql are the activation energies for the peak and for lattice diffusion, respectively). In the past, when Qp and QL were found to be comparable, the relaxation peak was explained in terms of grain boundary sliding.10 The equivalence of Q, and Qb. the activation energy for grain boundary diffusion, prompted the suggestion that it was a consequence of reversible grain boundary migration on an atomic scale." A new model for the LTP, which is based on the experimental relationships in Figs. 1 and 2, is presented. In region (a) it is suggested that stress relaxation occurs through the reversible glide and climb of grain boundary dislocations; in region (b) only reversible glide can take place. The resultant effect on the grain boundary might be sliding or "a bowing out", but, since the total distance moved will be 50A, the atomic movements are considered of primary im- portance. It must be emphasized that this is only a qualitative model, but at the moment it appears the most likely way to explain the widely varying, but re-

Jan 1, 1969

By R. W. Heckel, R. A. Tanzilli

Treatment of the finite, diffusion-controlled, two-phase, moving-interface homogenization problem has been carried out by numerical methods for a wide range of input parameters. Solutions have been obtained for planar, cylindrical, and spherical diffusion geometries. The effects of parameters such as the interdiffusion coefficients (concentration-independent) of- both phases, the concentrations (time-independent) of each phase at the interlace, mean composition, initial size of the dissolving- phase, and initial composition of- the two phases are considered. The results are displayed to show both the position of the interjace and the degree of homogenization (expressed in terms of concentration at the matrix phase symmetry boundary) as a function of diffusion time. Typical exaw~ples to which the results may be applied are discussed. A limited number of exact, closed-form solutions to the multiphase, diffusion-controlled, moving-interface problem exists in the literature, e.g., Refs. 1 to 7. The exact, closed-form solutions generally consider the outermost phases to be infinite in extent and also assume an interfacial velocity function. It is through use of such boundary conditions that closed-form solutions are readily obtained. An extensive literature also exists on numerical solutions to the mathematically analogous solidification problem, e.g., Refs. 8 to 12. In addition, a numerical solution involving mass transfer with spherical interfaces and infinite boundaries has recently been carried out.13 A practically important class of diffusion problems exists, however, in which the boundaries of each phase away from the interface are finite. For example the finite boundary condition arises when one sets up a model for analyzing the homogenization behavior of two-component powder compacts in two-phase systems or for studying the solution behavior of precipitates. Although exact, closed-form solutions have as yet not been found to this class of problems, solutions are possible using numerical methods. The purpose of this paper is twofold: 1) to describe a numerical method for treating the two-phase, diffusion-controlled, moving-interface problem involving finite boundaries with planar, cylindrical, and spherical interfaces; 2) to present the results of a parametric study which identifies the role played by each variable appearing in the analytical model. R. A. TANZlLLI,Student MemberAIME,onleaveofabsence from the General Electric Co., Re-entry Systems Department and A. W. HECKEL, Member AIME, are Graduate Student in Materials Engineering, and Professor, Department of Metallurgical Engineering, respectively, Drexel Institute of Technology, Philadelphia, Pa. Manuscript submitted May 6. 1968. IMD MATHEMATICAL MODEL The three geometries analyzed are shown in Fig. 1. For each configuration a symmetry element is shown, across whose boundaries the mass transfer is zero. Mean composition, C, and the characteristic solute-rich phase half-thickness (or radius), 1/2, are the independent variables while the characteristic symmetry element half-thickness, L/2 (measured from solute-rich phase center to the matrix phase plane of zero mass transfer), is a dependent variable. The symmetry element for a planar interface accurately represents a real diffusion situation involving the stacking of symmetry elements of constant size. Because cylindrical and spherical symmetry elements of constant size cannot be stacked to fill space, the meaning of the dimension, L/2, for these situations may be considered in terms of the following approximations: and where NA is the number of parallel cylindrical elements per unit area on a surface normal to the cylinder axes and Nv is the number of spherical elements per unit volume. The model consists of a solute-rich phase matrix phase composite of limited mutual solubility. The concentrations at the interface are assumed constant with time; no assumption of local equilibrium at the interface is necessary except for the case where the

Jan 1, 1969

By E. J. Nielsen, P. R. Strutt

A study has been made of the progressive changes in the distribution of etch-pit structures occurring during high-temperature creep in copper + 7 wt pct Al single crystals oriented with a [113] tensile axis. The two equally stressed glide systems with the highest Schmid factor would be expected to form subboundaries of the type predicted by Kear.2 The alignments of etch-pits on sections parallel to different (111} planes consistent with these types of boundaries were not observed. However, they were consistent with planar subboundaries (on a macroscopic scale). From an analysis of Amelinckx1 it may be shown that stable cross-grid dislocation boundaries may form in the primary slip planes. These boundaries form when dislocations with a Burgers vector not in the slip plane move into the plane by combination of climb and glide. THE geometry of subboundaries formed by the interaction of dislocations of two glide systems has been analyzed by Amelinckx,1 and the particular types produced by deforming fee crystals are predicted by ear.&apos; In this paper types of boundaries which may be formed when climb as well as glide occur are discussed as this is relevant in high-temperature creep. It is assumed in the present investigation that the etch-pits observed in Cu + 7 wt pct A1 on surfaces parallel to {111} planes delineate the sites of dislocations. Although there is no direct evidence for this previous work on a-Cu/Al single crystals by Mitchell, Chevrier, Hockey, and Mon-aghan,3 would show this assumption to be reasonable. The alignments of etch-pits which form during creep are studied on sections parallel to each {111) plane. It is then deduced that these alignments are consistent with a specific type of planar subboundary. The Cu + 7 wt pct A1 single crystals had a [113] tensile axis and Fig. 1(a) shows schematically the relation of the slip planes and slip directions (as represented by tetrahedron ABCD) with reference to the tensile axis. The two equally stressed glide systems with the maximum Schmid factor namely ß-AD and (a-BD, from the analysis of Kear,2 would be expected to form the boundaries shown in Fig. l(a) and (b), also Fig. 5(a) and (b). EXPERIMENTAL PROCEDURE The a-Cu/Al single crystals were grown and annealed in a "gettered" argon atmosphere. Chemical analysis showed the aluminum content to be uniform in each crystal and the difference between crystals was maintained to an accuracy of ± 0.25 wt pct. The initial dislocation density and mean subgrain diameter after annealing was -106 cm-2 and 250 µ, respectively. Surfaces parallel to (111) planes were produced by specially developed electrolytic machining processes. The {111} faces were next electropolished for 5 min in a solution consisting of 25 g chromium trioxide, 113 ml glacial acetic acid and 40 ml water; the applied potential was 8 v. Dislocation etch-pits were revealed using l an etchant described by 1 ml bromine, 45 ml HCl, and - 250 ml water. RESULTS In crystals strained into secondary creep at higher stresses (443 and 750 g - mm-2 at 650° C aligned rows of etch-pits parallel to slip plane traces were evident in sections parallel to the (1111, (ill), and (111) planes, see Fig. 3. As well as the longitudinal alignments in Fig. 3, well formed randomly oriented arrays indicative of an equiaxed subgrain structure are evident. At the lower stresses (100 to 230 g . mm-2) only an equiaxed structure formed during creep. The sections in Fig. 3 are from a crystal crept for 70 hr at 650°C with a CRSS of 443 g.mm-2. Two identically oriented crystals were also deformed at the same temperature and stress for 5 min and 4 hr. In the crystal crept for 5 min, the etch-pits were randomly distributed with no tendency for directional alignment, see Fig. 2(a). As shown in Fig. 2(b) aligned arrays were evident after 4 hr creep but they were not nearly so well defined as in Fig. 3. The alignments (parallel to the arrows) in Fig. 3 are consistent with the existence of boundaries in the two main slip planes a and ß. The way in which this is deduced is seen by reference to Fig. l(c), where the existence of boundaries in the a and ß planes is verified by sectioning parallel to a,ß, and d. The (111) and ß(111) planes intersect the d(111) plane along BC [101 ] and AT [011] and alignments parallel to [101] and [011] are clearly evident in Fig. 3(c) in a section parallel to the d(111) plane. Similarly the a, and ß planes in Fig. l(a) intersect each other along DC [110] and hence there will be an alignment parallel to [110 ] in sections parallel to the a-plane and the ß-plane; this is evident in Fig. 3(a) and Fig. 3(b). It is interesting to note that alignments of etch-pits consistent with the boundaries predicted by Kear2 were not observed; see Figs. l(a) and l(b). The geometry of boundaries in {111} planes as shown in Fig. l(c) is discussed later. In Fig. 4(a) the individual etch-pits are resolved and the alignments are exactly parallel to the slip trace direction [101]. However, in some areas alignments deviate away from the slip trace direction by as much as 10 to 15 deg, this is evident in Fig. 4(b), and in Fig.

Jan 1, 1969

By A. R. Krause, C. Laird

In order to establish whether or not there is a real temperature effect in fatigue (independent of environment) , poly crystalline copper and Cu- 7.9 A1 alloy have been cycled at 298° and 7° K in vacuo and the fatigue lives compared with those in air and in liquid nitrogen. The lives of both copper and the alloy were found to be highly temperature-dependent in the absence of environment. This result casts serious doubt on the validity of the cell structure hypothesis for stage I crack propagation as presently formulated, because it predicts that there should be no such tempevnture dependence. On the other hand, the plastic blunling process is consistent with the result. Effects of environment aside, the homogenization of slip which accompanies testing at low temperature, and at low strains, seems to be the main cause for increased fatigue life. At high strain amplitudes, the fatigue lives of wavy slip materials, typically copper, are independent of temperature.&apos; It is well-known, however, that low-strain lives greatly as as the temperature of testing is decreased. By contrast, the lives of planar slip materials, such as Cu-7.9 pct A1 alloy, increase to an even greater extent with decreasing temperature throughout both the high and low strain ranges.1&apos;2&apos;5 The mechanism of this temperature effect is associated with the earliest stages of fatigue failure,&apos;" crack nucleation, and stage I growth,"&apos; which is slow propagation along slip bands to the depth of a few grain diameters. Such life behavior has been interpreted on at least two different bases. On the one hand, those interested in the temperature effect at high strain amplitudes1 believe that stage I growth occurs by the plastic blunting process of crack propagation.7&apos;9 They explain the effect in planar slip materials by the homogenization of slip* which accompanies fatigue testing at low temper- atures and serves both to delay crack nucleation and to decrease the rate of stage I propagation. On the other hand, Holt and Backofen,2 who have studied the effect in low strain fatigue, believe that stage I growth can be interpreted by a cell structure hypothesis.10-12 They have challenged2 the conclusion that there is a real temperature effect in this regime of fatigue testing and have interpreted the increased fatigue lives almost entirely in terms of the "environmental-protective&apos;&apos; effect of the liquid nitrogen and helium baths used to obtain low temperatures. This interpretation by Holt and Backofen2 may offer a means of discriminating between these two mechanisms as currently formulated and used to explain stage I growth. On the basis of the plastic blunting process applied to stage I crack propagation,7* the low strain fatigue lives of both wavy and planar slip materials should be increased with decreasing temperature. This follows because both materials show increased slip homogenization in this strain regime."13 Consequently, crack nucleation in intensified bands will be delayed and the linking of such small cracks into larger stage I cracks will be difficult. In addition, the blunting process required to lengthen a stage I crack from the order of 2 to 10 (where the strain concentration of the crack begins to overcome the slip homogenization property of the material) will also be retarded. These delays will give rise to longer lives in both kinds of material. In contrast to the blunting hypothesis, no temperature dependence has been predicted on the basis of the cell structure hypothesis, because it is well-known that materials cycled at low temperature show no differences in type of dislocation structure for a given strain amplitude.18"20 If the lives of wavy and planar slip materials do show a temperature dependence when the environment is eliminated as a variable, then it is questionable whether cell structures per se have a fundamental role in fatigue fracture. Accordingly, specimens of copper and Cu-7.9 wt pct A1 have been cycled at 298° and 77°K in vacuo and the fatigue lives compared with those in air and in liquid nitrogen, in order to establish whether or not there is a real temperature effect in low strain fatigue. Since it is difficult to measure the strains in specimens when cycled in vacuo, S-N curves have been used as the basis of comparison. In studying the influence of temperature on fatigue life in ordinary environment, Holt and Backofen2 used the superior basis of E-N curves. However, they also published S-N curves and thus established the relationship between E-N and S-N curves. This relationship is used to support the S-N comparison reported in the present investigation. EXPERIMENTAL Materials. The copper employed in this investigation was of 99.99 pct purity and the cu-7.9 pct A1 was prepared from metals of the same purity. The stock, of 3 in. initial diam, was reduced in size by rolling

Jan 1, 1969

By E. Mille, R. Geffken

The Mg-Si and Mg-Ge phase diagrams were rede-levtnined by thermal analysis, and the existence of a single congruent melting compound in each system was confirmed. The melting points of the two compounds Mg2Ge and ,Wg2Si were found to be 1117.4° and 1085.0°C respectively. The euteclics for the Mg-Ge system occur at 635.6°C (1.15 at. pcl Ge) and 696. 7°C (64.3 at. pct Ge); for the Mg-Si system the eutectics are at 6376°C (1.16 at. pct Si) and 945.6°C (53.0 al. pcl Si). The phase diagrams and known thermodynamic data were used to calculate activity values for both systems. The activities calculated for the Mg-Ge system agreed very well with those previously published. Partial molar enthalpy values for the Mg-Si systetn were calculated from the phase diagram for the composition region where no experimental values have been reported. THE phase diagram for any system is an important source of thermodynamic data. Steiner, Miller, and Komarek1 have derived equations which permit calculation of the activity in binary systems with an inter-metallic compound! if the liquidus and enthalpy data are known. The thermodynamic properties of the Mg-Ge and Mg-Si systems have recently been determined in this by by an isopiestic method, and it was considered that it would be interesting to compare these directly determined values with those computed from the phase diagram. The basic features of the Mg-Ge and Mg-Si systems are essentially similar. The one intermediate compound present in each system. Mg2X, crystallizes in the antifluorite structure and melts congruently. Raynor4 has accurately determined the temperature and composition of the magnesium-rich eutectic in both the Mg-Ge and Mg-Si systems. Klemm and West-linning5 investigated the entire Mg-Ge liquidus, employing sintered alumina crucibles; the purity of the magnesium and germanium starting materials was not reported. The melt was not stirred, and the temperature was automatically recorded to an accuracy of ±3°C. The authors reported large weight changes due to magnesium evaporation between 50 and 67 at. pct Mg. The Mg-Si system has been studied by a number of investigators, and the results have been compiled by Hansen and Anderko.6 Significant discrepancies exist between the two principle investigations of voge17 and Wohler and Schliephake.8 Two different grades of silicon were used by Vogel, one of 99.2 pct purity and the other quite impure, containing 6 pct Fe and 1.7 pct Al. The magnesium purity was not specified. The melts were contained in graphite crucibles with porcelain thermocouple protection tubes under an atmosphere of hydrogen. Samples weighing 10 g were rapidly heated to 50° to 100°C above the liquidus: held, and then rapidly cooled without stirring. Accuracy was ±1 at. pct which is equivalent to a maximum error in temperature of ±18°C. Wohler and Schliephake used 97.9 pct Mg and 99.48 pct Si. The graphite crucibles contained a stirrer and the 15-g samples were melted under an atmosphere of streaming hydrogen. The samples were chemically analyzed after each run. Because of the scarcity of the data, the impurity of the starting materials, and the resultant uncertainty and inconsistency in the published liquidus values, it was decided to undertake a reevaluation of the Mg-Ge and Mg-Si phase diagrams by thermal analysis. EXPERIMENTAL PROCEDURE Alloys were prepared from 99.99+ pct Mg (Dominion Magnesium Ltd.) with impurities in ppm: 20 Al, 30 Zn, 10 Si, <1 Ni, <1 Cu. <10 Fe; 99.999 pct Ge (United Mineral and Chemical Corp.), and 99.999 pct Si (Wacker Chemie Corp.). All graphite parts were machined from high-density (1.89 g per cu cm) G-grade graphite obtained from Basic Carbon Corp. with a total ash content of 0.04 pct. Boron nitride parts were machined from rods of National-grade H.B.N. boron nitride. All graphite and boron nitride pieces were baked out under running vacuum at 1100°C for 24 hr before us Cylindrical graphite crucibles (1; in. OD, 23/4 in. long, l3/8 in. ID) were tightly closed with threaded graphite covers which had 21/4-in.-long thermocouple wells and 1/4-in.-diam off-center holes for stirrers. The cover and thermocouple well were machined from a single piece of graphite. A stirrer was made from a flat cylindrical graphite plate perforated with five 3/16-in.-diam holes and a 1/2-in.-diam central hole, and was held parallel to the crucible bottom by a 1/4-in.-diam. 4-in.-long graphite rod which screwed into the plate and extended up through a tightly fitting hole in the crucible cover. An iron core enclosed in a glass capsule was attached to the stirrer with an 18-in.-long molybdenum wire, so that the stirrer could be magnetically raised and lowered from outside the system. One crucible and stirrer with essentially the same dimensions given above was made entirely of boron nitride. Chunks of magnesium were premelted, cast into 11/2-in.-diam. rods, and then cut into lengths varying from a to 1 in. A 5/16-in. hole was drilled through the center of each piece to accommodate the thermocouple well and the individual pieces were then cleaned and rinsed with acetone. The total weight of an alloy was 50 to 70 g in the Mg-Ge system and 40 to 60 g in the Mg-Si system. The pure components were weighed to an accuracy

Jan 1, 1969

By S. Dinda

A series of as -quenched 4340 bars were drawn through a carbide die to various reductions. The X-ray diffraction technique of Lopata and Kula was employed to detect preferred orientation in drawn martensitic steel bars with low amounts of deformation, as lord as 0.8 pct The specimen face of each bar examined was cut at a 45-deg angle to the bar axis. The reflecting planes in the 45-deg face were varied by appropriate rotation of the sample using a spectrogonionzeter. TIE X-ray bean of a diffractometer was reflected from the center of the bar and the diffracted intensity was delected with a proportional counter and recorded. Intensity peaks were developed by cold working for 110 planes oriented at 0 and 60 deg to the bar axis. The intensity peaks increased with increasing defortnalion us a preferred orientation with a 110 texture developed parallel to the drawing direction. The intensity peaks for deformed as-quenched specimens remain unchanged after tempering at temperatures as high as 1000°F. The same amount of preferred orienlalion was observed both inferritic (hot-rolled) and martensitic (as-quenched) structures after an equivalent amount of deformation. THE deformation of martensite with medium carbon content. less than 0.5 pct, has been studied by Breyer et a1.1,2 It was reported that changes in properties such as resistivity, carbide precipitation, and the introduction of a yield point phenomenon were produced after cold reduction of as-quenched AISI 4340 steel bars. Later, Breyer and Nachtman3 studied the effect of cold reduction upon X-ray line intensity. They showed that the integrated 110 line intensity increased with increasing deformation when the planes examined were perpendicular to the die drawing direction. The integrated 110 line intensity for planes oriented at 45 deg to the die drawing direction, in contrast, were found to slightly decrease. These changes were proposed to be consistent with the previously proposed model of a stress-induced ordering of carbon atoms in the vicinity of dislocations.1,2 Objections can be raised to the above interpretation of the X-ray results on two grounds: a) Rough structure factor calculations indicate that the intensity changes are too large (50 pct observed vs 2 pct calculated4,5) to be the result of changes in the location of iron atoms produced by the stress-induced ordering of the carbon atoms. b) The results might be explained in terms of preferred orientations, although X-ray evidence of the development of texture has not been reported in the literature for deformations as slight as 1 or 2 pct. The aim of the present work was to determine if preferred orientation was present in such cold-drawn martensitic steel bars. In drawn rod or wire there is generally a certain crystallographic direction which is aligned in the direction of the wire axis, and the crystallographic planes are distributed symmetrically around this "fiber axis".6-8 This type of cylindrical specimen, with the fiber axis located at the center, will show rotational symmetry. Lopata and Kula9 proposed an experimental method utilizing a specimen cut at 45 deg, see Fig. 1. The X-ray beam is diffracted from the center of this bar cross section. The specimen is rotated around an axis perpendicular to the bar axis and lying in the 45-deg cut face. This permits the angle between the normals to the reflecting planes and the bar axis to be varied from 0 to 90 deg.9 With this arrangement the errors due to absorption and irradiated volume compensate each other.&apos; This greatly simplifies analysis of the data and is of considerable advantage for quantitative measurements. If there is preferred orientation in the specimen, more planes are oriented in a particular direction in the bar. When the bar is rotated to the favorable Bragg condition for that particular orientation, the intensity will be higher than that for some other angle. This technique was adopted for the present investigation.

Jan 1, 1969

Jan 1, 1969

By L. C. Brown, S. K. Behera

The diffusion rate in Ag-Sb couples is sensitive to con~pressive load with the width of Ag3Sb, the only phase present in the diffusion zone, increasing with stress up to 800 psi and remaining constant above this. Kirkendall marker experiments show silver to diffuse much faster than antimony in Ag3Sb and incipient porosity may therefore develop at the Ag/Ag3Sb interfnce restricting the transfer of atoms from the silver into the diflusion zone. Application of compressive stress reduces the tendency for porosity to develop and so increases the growth rate. In a recent paper Brown et al.1 observed a significant increase in the thickness of Cu2Te in Cu-Te diffusion couples on application of a compressive stress as low as 20 psi. Similar stress effects have also been observed in the Fe-A1,2 Al-u,3 arid cu-sb4,5 systems. It has been suggested that the increase in growth rates of intermetallic phases in these systems is due to a decrease in the amount of Kirkendall porosity with applied stress. In the present paper, results are presented of the effect of compressive stress on diffusion in Ag-Sb, together with a detailed examination of the Kirkendall effect. The Ag-Sb phase diagram6 shows that antimony has a moderate degree of solid solubility in silver, 5.7 at. pct at 350°C, but that there is essentially no solubility of silver in antimony. There are two intermediate phases— (hcp7) from 8.8 to 15.7 at. pct Sb and Ag3Sb (orthorhombic8) from 21.8 to 25.9 at. pct Sb. EXPERIMENTAL Diffusion couples were prepared from fine silver of 99.95 pct purity and from antimony of 99.7 pct purity. Both the silver and antimony were produced in the form of discs 1/2 in. in diam by approximately $ in. thick, with surfaces ground flat to 3/0 emery paper. Diffusion anneals were carried out in the apparatus previously described.1 A compressive load was applied to the diffusion couple through a lever arm system, with a reproducibility estimated to be ±10 psi. All runs were carried out in a protective hydrogen atmosphere. Following the diffusion anneal specimens were sectioned and polished and the width of the diffusion zone was measured metallographically. Composition profiles were measured using an electrostatically focused electron probe with a spot size of 10 , counting on Sb L radiation. Corrections for matrix absorptiori and fluorescent enhancement9 were not required. S. K. BEHERA, formerly Graducate Student, Department of Metallurgy, University of British Columbia, is now Postdoctoral Fellow, Whiteshell Nuclear Laboratories, Atomic Energy of Canada Ltd., Pinawa, Manitoba. L. C. BROWN, Junior Member AIME, is Associate Professor, Department of Metallurgy, University of British Columbia, Vancouver, B.C., Canada. Manuscript submitted June 14, 1968. IMD RESULTS Fig. 1 shows an electron probe traverse of a typical diffusion zone. In all couples examined only one intermediate phase was observed and the composition of this phase, 23 wt pct Sb, was in good agreement with the composition of Ag3Sb, 23 to 28 wt pct Sb. The presence of this phase was confirmed by X-ray diffraction of filings taken from the diffusion zone. The probe traverses showed no detectable solid solubility in either the silver or the antimony although the phase diagram indicates that some antimony, up to 6.5 wt pct pct Sb, should be in solid solution in the silver. However the width of this portion of the diffusion zone would be expected to be very small in view of the low diffusion coefficient in the silver, 4 x 10-l6 sq cm per sec at 350°C, 10 compared with that in the Ag,Sb, estimated as 3 x 10-8 sq cm per sec in the present work, and this region would therefore not be expected to be seen in the probe traverse. Application of stress resulted in a significant increase in the width of the diffusion zone, Fig. 2. At 350°C, the thickness of Ag3Sb increased from 250 at 0 psi to 400 p at the limiting stress of 800 psi, indicating an apparent 150 pct increase in the diffusion coefficient. Similar behavior was also observed at 400°C, indicating that the stress effect is not characteristic of just one temperature. The growth of Ag3Sb at 350°C and at various stresses is shown in Fig. 3. In every case the growth rate was parabolic indicating diffusion control. The kinetic curves all passed through the origin showing that delayed nucleation of Ag3Sb was not responsible for the stress effect and that it was a real growth effect. A series of tests were carried out in which diffusion was allowed to take place at a lower stress following an initial high stress diffusion anneal. Speci-

Jan 1, 1969

By A. F. Crawley

The density and viscosity of 1iquid thallium have been measured by absolute methods to temperatures of about 200° and 150°C, respectively, above the melting point. These new data reported, especially density data, do not closely confirm previous work. Density p, in g per cu Cm, is shown to vary linearly with temperaluve t, in °C, according to the equation p = 11.658 - 1.439 X l0-3t. The viscosity data obey the well-known Andrade equation nv1/3 = A exp C/vT , the constants A and C for thallium having values of 2.19 x A and 79.648, respectively. This paper reports some new data for the density and viscosity .of liquid thallium. Measurements of these fundamental physical properties were undertaken as part of a continuing research program at the Mines Branch, Department of Energy, Mines and Resources, Ottawa. Canada. A literature search has revealed that data are so scarce that there could not be a consensus on the true values of the density and viscosity of liquid thallium. To be more specific, there exists only one set of viscosity data&apos; and only two acceptable sets of density data,273 one of which is limited in scope.3 In Liquid Metals Handbook,3 another density study is reported but indications of impurities in the thallium render the results suspect. In this situation, further careful experimentation was required to realize the true density and viscosity of thallium. EXPERIMENTAL METHODS Density. Densities were determined using a graphite pycnometer. The technique and its accuracy have been discussed in earlier papers.4&apos;5 It is considered that experimental data can be obtained which are accurate within +0.05 pct, all sources of random and systematic errors having been evaluated. Density results for thallium were identical whether measured under an atmosphere of argon or a vacuum of 5 x 10-6 torr and, for the most part, the argon atmosphere was used. Viscosity. Viscosity measurements were made in an oscillational viscosimeter by an absolute method—the liquid metal being held in a closed graphite cylinder. Design and operation of the apparatus, constructed in this laboratory, have previously been discussed.6 For thallium, runs were made under a vacuum of about 2 x 10-6 torr. To evaluate viscosity coefficients from the various experimental parameters, the mathematical analysis of Roscoe7 was used. Measurements of the necessary parameters and the accuracy of these measurements have also been discussed.6 The cylinder dimensions were corrected for the anisotropic expansion of graphite, as discussed for density measurements.4,5 It is well-known that thallium oxidizes rapidly and hence a newly machined surface quickly tarnishes in air. The oxide film, however. is nonadherent and is easily removed by rubbing or by solution in water. Hence, immediately before use, both density and viscosity charges were immersed in water, wiped dry, and quickly transferred to the apparatus which was then rapidly evacuated. Specimens removed after determinations were only slightly tarnished and there was no other evidence that tarnishing affected the results. For example, the sharpness of the specimen edges from the containing vessels indicated complete filling by the liquid metal. Thallium of 99.999 pct purity was used in this investigation. Because of its high toxicity care was exercised in handling this material. For example, the melting procedure to prepare machinable ingots was carried out in an open, well-ventilated area, while protective gloves were always worn when handling the solid metal. RESULTS AND DISCUSSION Density. Measurements were made over a tempera-ture range of about 200°C above the melting point. The results are listed in Table I and plotted in Fig. 1. From the graph it is evident that the relation between density and temperature is linear. Such a relation has been observed before in this program for other metals and alloys475 and elsewhere by other workers. A least-squares analysis of experimental data gives the equation: pT1 = 11.658 - 1.439 x 10-3t where p = density in g per cu cm and t = temperature in "C. In Fig. 1, together with the present results, the data of Schneider and Heymer2 in the corresponding temperature range have also been plotted. Evidently, the two sets of data do not agree well, the results of Schneider and Heymer being about 0.6 pct higher. Viscosity. Viscosity data were obtained from the melting point, 303.5°C, up to 457.5"C. The data are listed in Table I and in Fig. 2 the plot of these results demonstrates a smooth curvilinear relation between

Jan 1, 1969

By J. R. Bell, W. J. Childs, J. H. Bucher, G. A. Wilber

A technique for determining recrystallization times as short as 0.10 sec was developed utilizing the "Gleeble", a commercially available testing system designed for the study of short-time, high-temperaLure themal and mechanical processes. The procedure consisted of heating a small tensile specimen to a given temperature of hot deformation, loading to a given reduction in area, unloading, delaying various intervals at temperature, and then reloading- to failure. The magnitude of the ultimate load obtained upon reloading decreased with delay lime as recrys-lallization proceeded. The technique was applied to austenite recrystallization in AISI 1010 and AISI 1010 uith 0.02 pct Cb steels. For each steel the reduction in area given the specimen on the first pull was mainlairred at 30 ± 5 pct and recrystallization times deterntined at various temperatures. The results indicaled a significantly slower rate of recrystallization for the columbium-modified composition, suggested the presence of- a recovery stage in the softening process , and indicated a greatly increased softening rate at a temperatuve where significant allotropic transformation to a partially ferritic Structure could occur. In recent years increasing attention has been paid to the fact that the process of recrystallization of austenite deformed at elevated temperatures is far from instantaneous at many practical hot-working temperatures.1-3 This realization has given rise to such terms as hot cold-working1 or warm-working,2 These terms generally describe processes where the recrystallization rate at the temperature of deformation is slow enough to have an appreciable effect on mechanical properties despite a relatively high deformation ternperature. The mechanical properties of interest can be either the properties at the deformation temperature as in hot-workability studies4 or the room-temperature properties after cooling as in the many recent studies of various thermomechanical processes172 where heat treatment and deformation are intentionally combined to give a unique set of room-temperature properties. Because of this interest in processes where the austenite recrystallization kinetics can be an important variable, the development of quantitative methods of following the course of short-time, high-temperature recrystallization has received increasing attention.l,3,5 The experimental methods to date have, in general, relied upon rapidly deforming the austenite, holding at temperature for various brief intervals, quenching as G.A.WILBER and W. J. CHILDS, Members AIME,are Research-Fellow and Professor, respectively, Rensselaer Polytechnic Institute, Troy, N. Y. J. R. BELL and J. H. BUCHER, Member AIME, are Research Engineer and Research Supervisor, respectively, Graham Research Laboratory, Jones & Laughlin Steel Co., Pittsburgh, Pa. Manuscript submitted March 13, 1968. IMD. rapidly as possible, and then using room-temperature measurements to follow the recrystallization process. Although such methods can be successfully applied to certain alloy steels, the existence of the allotropic transformation during cooling of plain-carbon or low-alloy steels tends to obscure the results. Thus, such room-temperature measurements as hardness and X-ray line widths do not correlate well with the extent of austenite recrystallization before quenching,5 and results based on room-temperature microstruc-tural observations are dependent upon the success in correlating the observed structure with the prior aus-tenitic grain structure.1,3,5 The purpose of the present work was to develop a quantitative method for the determination of short-time, high-temperature recrystallization rates, based on measurements made at the temperature of deformation. EXPERIMENTAL TECHNIQUE The basic technique consisted of heating a small tensile specimen to a given temperature of hot deformation, loading to a given reduction in area, unloading, delaying various intervals at temperature, and then reloading to failure. The data were obtained in the form of traces of load and elongation as a function of time. Due to the high deformation temperature, the strain hardening introduced during initial loading was progressively annealed out with holding time after unloading and the loads obtained upon reloading decreased as this softening proceeded. Although the value of the second load at any Consistent point On the load-elongation curve could have been used as a measure of the degree of softening, the most convenient to use was the ultimate load. The softening indicated by the decrease in the second ultimate load with time is essentially a process of annealing of cold-worked material at a high deformation temperature. Although some recovery grain growth may contribute to such a softening process, it is generally considered that the major softening which must take place to achieve complete removal of substantial Strain hardening will occur by the formation of new, stress-free grains. As the results of this work indicate that essentially complete removal of strain hardening did in fact occur. the primary softening process will be attributed to recrystallization, and specific reference made where it appears that other mechanisms may be contributing to the total observed softening. It would, of course, be of interest to attempt to correlate the results of this work with the actual austenite fraction recrystallized as determined by other techniques. This was not attempted in the present work because it would have required running a large number of additional specimens and, as discussed previously, there is limited assurance that the results would accurately reflect the prior austenite fraction recrys-

Jan 1, 1969

By G. R. Leverant, C. P. Sullivan

To evaluate the effect of a dispersion of nondeform-able, incoherent, second-phase particles on high-strain cyclic deformation and fracture, recrystallized TD-nickel (Ni-2ThO2) and a commercially pure nickel, Ni-200, were fatigued under strain control at total strain ranges varying from 0.009 to 0.036. Relative to the Ni-200, the slip at the surface of the TD-nickel was more wavy and discontinuous due to the presence of the thoria particles. This made crevice formation (incipient cracking) within slip bands more difficult in TD-nickel than in Ni-200. Both materials cyclically hardened to a constant (saturation) flow stress which increased with increasing plastic strain amplitude. Cellular substructures were developed in both materials during cycling. The cell size in TD-nickel was controlled by the thoria particle distribution and was independent of plastic strain amplitude over the range investigated. The cell size in Ni-ZOO was larger than that in TD-nickel at similar plastic strain amplitudes and was a function of plastic strain amplitude. These results, together with the cyclic stress-strain curves for both materials, are discussed in terms of a model for fatigue strain accommodation at saturation recently proposed by Feltner and Laird. NUMEROUS fatigue investigations have considered the interrelation of slip character, dislocation substructure, and cracking in pure metals and solid-solution alloys. However, except for the studies of the low-strain fatigue of internally oxidized copper alloys1 and cast, dispersion-strengthened lead,&apos; little is known about the effects which small, incoherent, nondeform-able, second-phase particles have on cyclic deformation and cracking processes. Effects due to the particles alone are often obscured by a dislocation substructure introduced during thermomechanical processing of dispersion-strengthened metals. In the present study, recrystallized TD-nickel and a commercially pure nickel, Ni-200, were employed to evaluate the effect of a thoria dispersion on high-strai fatigue deformation and cracking at room temperature. I) MATERIAL AND EXPERIMENTAL PROCEDURE The TD-nickel was supplied by DuPont as a 5/8-in.-thick stress-relieved plate which had been subjected to a proprietary schedule of thermomechanical treatments, and the Ni-200 as 3/4-in. bar which was subsequently annealed for 2 hr at 850°C in argon resulting in an average grain diameter of 0.05 mm. The compositions of these materials are given in Table I. The microstructure of the TD-nickel consisted of elongated grains parallel to the primary working direction with an average width of 0.16 mm, Fig. l(a). Many fine annealing twins were present indicating that the starting material was in a recrystallized condition; this supposition was confirmed by the absence of of any extensive dislocation substructure, Fig. l(b). Sheetlike stringers parallel to the rolling direction were occasionally seen both within grains and at grain boundaries. Some approximately spherical particles about 2 in diam, which may correspond to exceptionally large thoria particle aggregates, were also present. The average Young&apos;s modulus of the plate material in the rolling direction was 21.8 X 106 psi which is consistent with a {100}<001>recrystalliza-tion texture3&apos;* being prominent. In transmission microscopy, the 2.3 vol pct of thoria particles generally appeared to be uniformly distributed although some clusters, 0.1 to 0.3 in diam, of larger particles were observed as previously reported for TD-nickel sheet,5 and stringering of particles was present in some areas as welt. The average diameter of the thoria particles was 450A with a calculated mean planar center-to-center spacing of 2100A, as determined by quantitative metallographic analysis.= The 0.2 pct offset yield stress was 36,000 psi which agrees with the value predicted by the modified Orowan relation7 for edge dislocations bowing between thoria particles of the size and spacing observed in the present investigation. Fig. 2 illustrates the specimen design employed for the axial high-strain fatigue testing. Adapters were screwed onto the threaded portions of each specimen so that testing could be performed in the same manner as that reported for buttonhead specimens.8 Stressing was coincident with the working direction for both materials. The gage section of each specimen was electropolished and lightly etched prior to testing. The total strain was controlled, being varied between zero and a maximum tensile strain ranging from 0.009 to 0.036. In addition to these tests, a circum-ferentially notched TD-nickel specimen was cycled over a total strain range of 0.0075. The same strain

Jan 1, 1969

By d&apos, K. Mukherjee, C. R. Antonio, R. J. Maciag, G. J. Fischer

Tensile data indicate that over the range of strain rates 10-5 to 10-1 sec-1 and in the temperature range 298° to 743°K the flow stress at a given temperature may be expressed as: C0 = Cem where m changes abruptly at a critical strain rate of 10-2 sec-1. The Zener-Hollomon parameter was tested and found to be invalid except at temperatures exceeding 700° K. Values of AH calculated for temperatures above 700°K ranged from 30 to 47.5 kcal per g-mole. ThE flow characteristics of aluminum and aluminum alloys as a function of temperature and strain rate have been of interest to various experimenters for many years. Trozera et al.1 determined tensile flow curves for pure aluminum and concluded that the combined effect of temperature and strain rate on the flow stress could be related using the Zener-Hollomon parameter. More recently, Hockett2 proposed a relationship between compressive flow stress, temperature, and true strain rate which could be represented by a surface. Holt et al.3 studied strain rate effects on flow stress in a number of aluminum alloys at room temperature. It was determined that there is a critical strain rate above which a strain rate effect is observed. It was also reported that the strain rate sensitivity was significant in aluminum alloys in the "0" condition only. In a recent review paper McQueen4 has considered a number of mathematical expressions which have been used to describe the relationship between stress, strain rate, and temperature. These expressions have been applied to the flow characteristics of a number of different metals and alloys including aluminum. In the present work the strain rate sensitivity of 7075-0 aluminum was determined in the temperature range of 298° to 743°K. The tensile flow stress at 0.2 pct offset was obtained over a nominal strain rate range of 10-5 to 10-1 sec-1. EXPERIMENTAL Threaded tensile specimens were cut from a single heat of 7075-T6 aluminum. The composition of this heat is given in Table I. The test bars had a gage section 1.5 in. long by 0.250 in. diam and conformed to ASTM specification E-8-57T. After machining, the bars were annealed at 413° ± 10°C for 2 hr. They were then cooled to 260°C in 3 hr, and finally air cooled to room temperature. This treatment is commonly used to produce the "0" condition. Load-time curves at constant crosshead speeds were obtained at various temperatures using an Instron testing machine. Crosshead speeds ranged from 0.002 to 40 in. per min. A three-zone resistance tube furnace was used for the elevated-temperature tests. Temperatures were measured at three points along the gage length by means of suitably placed thermocouples. Each tensile bar was held at temperature for 30 min prior to testing and the maximum temperature variation along the gage length was kept below 1°C. In all, 275 samples were tested and each data point plotted is an average of at least two tests. In many cases the point represents up to six tests. RESULTS AND DISCUSSION Values of the flow stress at 0.2 pct offset at six different temperatures are plotted vs strain rate on log-log coordinates in Fig. 1. Over discrete ranges of strain rate, the data for each temperature fit the expression:

Jan 1, 1969

By A. Rosenzweig, M. M. Karnowsky

The generalized binary diagram of the Au-Sn-Pb system is presented. The chief characteristic is the pseudobinary between lead and AuSn. On the high-gold side of the pseudobinary, four reaction isotherms were found at 363°, 274°, 225°, and 204°C. On the low-gold side of the pseudobinary, three reaction isotherms at 277°, 205°, and 176°C were found. A vertical section from the eutectic solder composition to gold was developed from the isothermal sections generated. METALLURGICAL problems arising from the intentional or accidental formation of Au-Sn-Pb alloys in soldering applications have indicated a need for information on the phase equilibria in this ternary system. The literature indicates that a complete diagram presenting this information has not been prepared. Even the recent excellent work by prince&apos; entitled "The Au-Pb-Sn Ternary System" actually extends only to the AuSn or 50 at. pct Au range. There are more events in the 50 to 100 at. pct Au than in the less than 50 at. pct range. This article by Prince furnished much guidance in preparing this report. Initial efforts with the isopleth from the eutectic solder composition 61.9 wt pct Sn-38.1 wt pct Pb and 0 to 90 wt pct Au indicated that extensions of the work to the whole of the diagram (even if in less detail) were necessary to understand this system. In undertaking the construction of such a diagram, this study used differential thermal analyses (DTA) and metallography with verification and identification of phases by electron microprobe analyses. EXPERIMENTAL PROCEDURE The procedure began with the development of a cell which would be unreactive with lead, tin, and gold, retain its strength to 1100°C, exclude oxygen, and also furnish a suitable well for insertion and protection of a thermocouple to monitor temperature changes in the material. Such a cell would make it possible to reuse the sample should a repetition of determination be desired. Fig. 1 is a photograph of two such quartz cells as finally developed. The specimens have been run many times. The cell is made up of an inner sample bucket and an outer capsule with a thermocouple well which the sample surrounds. The DTA unit was an assembly devised from available instrumentation. The sample holder was a 3-in.-long cylinder of nickel, 2 1/2 in. in diam, fitted securely in a vertical tube furnace. Two holes 7/8 in. in diam were symmetrically located to receive the quartz cells. A dummy cell with nickel powder was used as the reference. The absolute temperature was recorded with a Pt/Pt 10-pct Rh thermocouple with an automatic Kaye ice bath compensator. (Calibration indicated the compensator to be accurate to better than ±0.5° over the 100° to 1000°C range.) The absolute temperature was measured in the sample and recorded on an L&N mul-tirange recorder with a full-scale display of 1 mv and automatic ranging of 99 mv. The differential signal between the sample temperature and the reference temperature was amplified with an L&N microvolt amplifier and recorded on an L&N Speedomax G recorder. Since two charts were obtained, the chart speeds were equalized and each event was noted on the differential chart, and the temperature at that time was obtained from the temperature record.

Jan 1, 1969

By H. L. Marcus, C. D. Turk

Titanium was physically vapor-deposited by electron beam high rate evaporation. Rates of 50,000 and 85,000Å per min at deposition temperatures of 480°, 535°, and 595°C were used. Deposited thickness ranged front 0.004 to 0.010 in. The evaporated titanium had a high degree of basal Plane texture. The specimens were tested in tension at temperatures ranging from 78° to 520°K. From the data, the yield stress, thermal component of the yield stress, and work hardening characteristics were found as a function of temperature, deposition rate, and deposition temperature. It was found that Taylor&apos;s equation, best fit the work hardening data with m = 1/2. MANY investigations have been made on the tensile deformation characteristics of commercial- and high-purity titanium.1"7 The data obtained from these experiments emphasize the fact that the mechanical properties are generally related to the method of production. The correlation of mechanical properties to production history arises from the dependence of impurity concentration on the extraction and melting technique used. Additional effects are derived from crystallographic texturing which can result from fabrication history. Lee and Backofen8 and other investigators9 have shown that crystallographic texturing in titanium sheet has a significant effect on the deformation characteristics. Bunshah and Juntz10 prepared high-purity titanium by high rate physical evaporation techniques. These authors found the deposited material to have a columnar structure with grain sizes ranging from 12 to 104 µ, depending upon the substrate temperature. The room-temperature strengths of the coarse-grained distillate were similar to arc-melted, rolled. and annealed crystal bar titanium. Commercial-purity titanium was also produced experimentally in our laboratory using high rate physical vapor deposition techniques. The commercially pure material has a finer structure than the high-purity distillate,10 and is highly textured. Since the method of preparation and degree of texturing affect the mechanical properties, a research program was initiated to determine the temperature dependence of the yield stress and work hardening characteristics as a function of high rate deposition parameters. This paper relates the results of the investigation. EXPERIMENTAL A) Material Preparation. The titanium was received in the form of commercial-grade 0.096-in.-diam wire which has a composition of 0.016 pct C, 0.0037 pct N, 0.110 pct 0, 0.011 pct H, 0.05 pct Mn, 0.051 pct Fe. balance Ti. The wire was continuously fed into a vacuum evaporation unit as shown schematically in Fig. 1. The deposition chamber was evacuated, purged with argon, and reevacuated to a pressure of 10-5 Torr which was maintained during deposition. A focused electron beam was used to evaporate the titanium from a water-cooled copper crucible. The titanium vapor was condensed onto a preheated titanium substrate. The temperature of the substrate was controlled within ±5°C for the deposition temperatures of 480°, 535°, and 595°C. Control of the input power enabled the use of two deposition rates. 50,000 and 85,000Å per min. The evaporated titanium had a final analysis similar to that of the input titanium, within experimental limits. B) Testing. The evaporated titanium was physically stripped from the titanium substrate and machined into tensile specimens with 1-in. gage lengths. In addition, tensile specimens of as received annealed 35-A titanium sheet with a 20 µ grain size and 45 pct cold-rolled 35-A were also prepared. All specimens were tested in tension in an Instron at a strain rate of 3.3 x 10"4 in. per in. per sec. Proportional limit has been used as a measure of yield strength. Tests were conducted at 78°, 220°, 300°, and 520°K. Metallography, X-ray diffraction, and electron microscopy were used to correlate structure with the deposition parameters and mechanical properties. Room-temperature X-ray measurements were made to determine the phases present. Pole figures and a scans were made to determine deposition texture. Because the vapor deposition was symmetrical about the normal to the substrate, there was no preferred di-

Jan 1, 1969

By R. Maddin, R. Pond

THERE have been many recent studies of nonequi-librium alloy structures using specimens which have been formed by rapid solidification.&apos; The general methods for achieving nonequilibrium structure utilize high velocity impingement of a liquid metallic droplet(s) and one or more substrates of relatively high heat conductivity. Specimens formed by current popular techniques are small and have various forms of irregular geometry which severely limit their use for many measurements of physical or mechanical properties. As a result of geometric limitations most research has been restricted to X-ray diffraction, electron microscopy, and to a small degree, electrical resistivity. Recently several attempts in mechanical property evaluation have been reported.2,3 A technique for casting large quantities of regular, rectilinear, continuous metallic fibers has existed for a number of years.4 We have utilized this technique with some slight modifications to produce nonequi- librium alloy structures. The apparatus is composed of a small open tube furnace, a pneumatic cage which raises and lowers a graphite ejection mold, and a

Jan 1, 1970