Search Documents

Jan 1, 1969

By S. D. Dahlgren

The plasticity of unalloyed P plutonium was studied by evaluating the strain-rate-hardening exponent, m, in the equation Values of m up to 0.33 and tensile elongations up to 680 pct were obtained for ß plutonium formed directly from the a phase. Casl bars that were cycled and tested had lower flow stresses and higher values for than uncycled bars , hut their total plastic elongations were not as great as expected because of premature failure at voids formed during cycling. Flow stresses were higher and m was lower (m = 0.15) for 9 plutonzutn formed from the y phase. ThE strain-rate-hardening exponent for plastic flow of p plutonium was determined as a function of strain rate, test temperature, and heat-treating history, and it was related to the rather large plastic elongation found previously for some plutonium tensile samples. Gardner and ~ann' obtained tensile elongations of up to 620 pct for P plutonium samples which had been completely transformed from the low-temperature a phase to the P phase before testing. Such a large percentage elongation is unusual for unalloyed metals or single-phase alloys.' The a phase is stable below approximately 112°C and (3 is stable between approximately 112" and 190"c.~ Both phases have mono-clinic structures. A temperature of 160°C is 0.58 of the effective absolute melting point, 475°C) of the p phase. The effective melting point is obtained by considering the enthalpy and entropy changes associated with the higher-temperature phase transformations and it is not the same as the experimental melting point of the highest-temperature allotrope of unalloyed plutonium. Nelson, Bowman, and Bierlein observed a striking difference between the ductility, as well as other mechanical properties, of p plutonium formed from the next higher-temperature phase (y) and the ductility of /3 plutonium formed from the a phase. The total elongation of /3 plutonium formed from the y phase was less than 5 pct. Earlier, the creep rate of 13 plutonium formed from the a phase was shown to be 200 to 500 times faster than the rate for 0 formed from y for the same test temperature and stress.

Jan 1, 1969

By S. R. Goodman, Hsun Hu

A detailed study of texture developmenf in poly crystalline copper atzd 70-30 brass has been completed. Textural changes as a function of deformation are shoum by pole jigmres and by intensity measurements oF- various rejlectiotzs from the rolling plane and the rolling direction. These examinations were accompanied by measurements of stacking fault frequency, hardness changes, and microstructure. Some of the results were briefly presented earlier. Additional results reported here are consistent with the idea that deformation faulting or slip by partial dislocations is of primary importance in the formation of deformation textures in fcc metals. lo examine the idea that deformation faulting is of primary importance in determining whether the texture is the copper type or the brass type an extensive study of the development of polycrystalline textures in copper and 70-30 brass was initiated. Besides the determination of complete pole figures, the intensities of the various reflections from both the rolling plane and the plane perpendicular to the rolling direction, the peak shifts due to deformation stacking faults, and the hardness of the rolled specimens were examined at various reductions from 10 to 99 or 99.5 pct. Mi-crostructures were examined by transmission electron microscopy. Some of the results were briefly presented in an earlier publication.' Since then, additional information has been obtained. This is given in the present paper. EXPERIMENTAL PROCEDURE Material and Specimen Preparation. The material used was a commercial electrolytic copper bar 1i in. wide and 2 in. thick and a 70-30 brass bar la in. wide and 1i in. thick. Chemical analysis indicated a purity of 99.97 pct for the copper, with 0.025 pct 0 as the major impurity. The 70-30 brass was of higher purity with 0.0016 pct 0 as the major impurity. Extreme care was taken in the preparation of the starting material to insure uniformly fine grains with a nearly random initial texture. The two bars were first cold-forged and then annealed to eliminate any original texture. The grains were then refined by several cold rolling (approx 30 pct reduction) and annealing treatments. The + -hr anneals were carried out in a salt bath at 390" to 440°C for copper and at 490°C for brass. The resulting penultimate grain size was 0.06 mm for copper and 0.03 mm for brass, and both showed very little preferred orientation. The number of prior cold rolling and annealing cycles was such that the final thickness after various final reductions of 10 to 95 (for brass) or 99 (for copper) pct was the same (0.020 in.). These annealed strips were rolled in two directions by reversing end for end between passes according to the following schedule: 0.006 in. per pass to 0.100 in., 0.003 in. per pass to 0.050 in., 0.002 in. per pass to 0.025 in., 0.001 in. per pass to 0.020 in. Texture Determination. The development of rolling textures was studied by examining complete pole figures determined from the (111) reflection. Specimens thinned from one face of the strip to half thickness (0.010 in.) were used to obtain the central portion of the pole figures, while specimens thinned from both faces to 0.003 in. were used to obtain the peripheral portion. The reflection and transmission techniques have been described previously. In addition to X-rav pole figures, texture development was also studied b; examining the intensity variation of the (Ill), (200), (2201, (311), (331), (420), and (442) reflections from the rolling plane and from the plane normal to the rolling direction, as a function of deformation. The same specimens used for the central portion of the pole figures were used for the intensity measurements of the various reflections from the rolling plane. For intensity measurements from the plane normal to the rolling direction, composite specimens were prepared by mounting sections cut parallel to the transverse direction of the strip. An epoxy resin was used to bond these sections together, and the entire composite was then mounted in a cold-setting resin to facilitate subsequent polishing and etching to remove distorted metal at the cut. The intensities were expressed in units of the integrated intensities measured from an annealed copper specimen having almost no preferred orientation. Stacking Fault Frequency Determination. Following the analysis of Warren: the stacking fault frequency, a, was determined from the change in the peak separation (A%) of two neighboring reflections of a deformed specimen, as compared with the normal peak separations of a fully annealed specimen. To obtain sufficient intensities for the second-order reflections, (222) and (400), composite specimens were prepared from parallel sections cut from the strip at 30 deg to the rolling direction for copper and 25 deg for the brass.* From texture data, these sections are known to contain a large population of both (111) and (200) planes. Since residual stresses can also cause X-ray line shifts (the direction of line shifts depends upon the sign of the stress), the use of composite specimens consisting of sectioned planes should help compensate for these effects as the residual stresses change sign from the surface to the central section of a rolled strip. Since the amount of peak shift is almost un-measurable in brass rolled 15 pct and in copper rolled

Jan 1, 1969

By Edwin F. Brush, John Chipman

Published data on the activity of carbon in binary and ternary austenite at 1000°C are reviewed. The composition variables are . The coefficient, Vj, has the value for substitutional elements but may be assigned a ualue -1 for silicon to effect a simplification on the mathematical treatment. The activity coefficient PC = is obtained from gas equilibrium data. For the ternary systems studied the Henrian activity coefficient is given by the expression: The principle advantage in cornparison with the analogous expression in terms of atom fractions is found in the fact that for most systems the final term and in many the last two terms are zero. Values of the interaction parameters are tabulated and the graphical comparison of the equation with experirt~ental data is sho,wn in several figures. The thermodynamic properties of the solid solution, austenite, are of considerable importance in the heat-treatment of alloy steels and in other aspects of ferrous metallurgy. Early studies embodied in the Fe-C diagram have been extended to include other binary and some ternary diagrams. Our best hope of obtaining a useful thermodynamic treatment of reactions in complex alloy steels will not be found in quaternary and quinternary phase diagrams but in determinations of activities and interaction relations among the several solute elements. The foundation for such a development was laid by smith' in his early studies of the activity of carbon in Fe-C alloys and his subsequent work on Fe-C-Si, Fe-C-Mn, Fe-C-Ni, and Fe-C-Co solid solutions.2"4 Other observers have also made noteworthy contributions and these will be discussed and correlated here in the light of a somewhat simplified mathematical treatment of solute interactions. Fe-C AT 1000°C In a recent review of the thermodynamic properties of binary Fe-C austenite it was shown that the simple mathematical treatment employed by smith' was capable of describing all the published results on this solution. The treatment utilizes the atom ratio, yc = nC/nF,, rather than the atom fraction. The activity of carbon is proportional to the equilibrium gas ratio, either measured on a scalk in which the activity of graphite is taken as unity or, alternatively, aC may be set equal to yc at infinite dilution. In either case the ratio aC/y = (PC, the activity coefficient. It was found that the experimental data of smith1 and those of Diin-wald and wagner; Bungardt, Preisendanz, and Lehn-ert,' and Scheil, Schmidt, and Wiinnings at temperatures of 800" to 1200° C as well as reliable data on the solubilities of graphite and cementite could be represented by the equation for which graphite is the standard state: The data on alloyed austenite have been obtained at 1000°C. For this temperature, the "Henrian" activity coefficient (which is unity at infinite dilution) is: FOr an interstitial solute such as carbon in austenite it has been shown by statistical mechanicsg that the activity in the infinitely dilute solution is proportional to the ratio of the number of lattice sites occupied by carbon to the number of yet unfilled lattice sites. A variable zz proportional to this ratio serves as a useful measure of concentration:" in which b is the number of lattice sites provided by each atom of solvent; in austenite b = 1. The Henrian activity approaches zz at infinite dilution and the ratio a is the activity coefficient. The effect of a change in concentration is then given by: It has been shown further that in some systems the derivative in Eq. [4] remains constant over a wide range of concentrations. In such a case second-order terms become negligible and the Henrian activity coefficients is:

Jan 1, 1969

By R. E. Smallman, I. Milne

The deformation behavior of single crystals of Nb-Mo alloys has been investigated with particular reference to the influence of composition, orientation, and temperature. Strong solid-solution hardening was observed reaching a maximum at the equiatomic cotrlposition and can be attributed to the difference in atomic size between niobium and molybdenutrz. Changes in the form of stress-strain curve, as shown by a high work-hardening rate and restricted elongation to fracture, were observed at a composition of Nb-85 pct Mo and are attributed to the presence of MozC DreciDitate. Conjugate slip was only extensive in dilute alloy samples; at the 50/50 composition deformation rnainly occurred by primary slip, and the onset of conjugate slip gave rise to failure by cleavage on (100). The variation of yield stress of Nb-50 pet Mo with orientation was consistent with slip on (011)(111) slip systems. The temperature deperndence of the yield stress between -196" and 250°C was similar to that of pure bcc metals, but at a much higher stress level; no evidence for twinning %as found. IN recent years the deformation behavior of various pure metals in groups VA and VIA has received considerable attention, but surprisingly little work has been carried out on binary alloys made by mixing metals from the two groups. Such an investigation would be of interest since single crystals of metals of group VA have been shown to deform characteristically with a multistage deformation curve1"3 while a parabolic type of deformation curve has been reported for most of the group VIA metals.4'5 It has been suggested by Law ley and Gaigher~ that the difficulty encountered in obtaining multistage deformation curves for molybdenum in group VIA was possibly because of the presence of a microprecipitate of MozC which they observed even at carbon contents as low as 11 ppm. Recently a multistage deformation curve has been reported for molybdenum ," although the stages are not so definitive as those for group VA metals. The binary alloys of the particular refractory metals which have been investigated in single-crystal form include Ta-w,' Ta- Mo,' and Nb- Na." While a large amount of hardening was observed for alloys of the Ta-W and Ta-Mo systems, associated with room-temperature brittleness for alloys approaching the equiatomic composition, Ta-Nb remained ductile over the complete composition range with little or no solution hardening. Other systems have been investigated by hardness measurements on polycrystalline material and a discussion of the hardening of these alloys has been presented by ~udman." The purpose of the present investigation was to examine the deformation behavior of Nb-Mo alloys in detail, with particular reference to alloy composition and single-crystal orientation. In this way it was hoped to shed some light upon the restricted ductility of these alloy specimens. 1) EXPERIMENTAL PROCEDURE The starting materials were obtained in the form of beam-melted niobium rod and sintered molybdenum rod of suitable dimensions. Since niobium and molybdenum form a complete solid-solution series at all temperatures, alloy single crystals were produced by melting the two constituents together in an electron bombardment furnace (EBM). To produce specimens free from segregation a molten zone was passed over the length of each rod six times in alternate directions at a speed of 10 in. per hr. Typical specimens were analyzed for interstitial impurities by gas analysis and for metallic impurities by spectrographic analysis. The results of this analysis are shown in Table I. Many of the tensile specimens were also analyzed (after testing) by scanning the gage length in an electron beam microanalyzer, from which it was found possible to predict the approximate composition of a specimen from the original proportions of each element in the EBM. The tensile specimens were made with a gage length of 0.5 in. and diameter of 0.075 in., using a Servomet Spark machine. By careful machining on the finest range for the final i hr of this technique, surface cracks could be reduced to the level where they were easily removed by electropolishing in a solution of nitric and hydrofluoric acids. The specimens were strained at a rate of 10 4 sec-' using friction grips designed to prevent accidental straining and maintain a good alignment before straining. The orientations of the individual specimens tested are shown in Fig. 1 and the corresponding compositions listed in Table I1 together with collated experimental data. 2)RESULTS a) General Deformation Behavior. The effect of composition on the room-temperature deformation curves of similarly oriented specimens is shown in Fig. 2. The yield stresses of the pure constituents, while not the lowest reported to date, were at least comparable with existing data. Although the solution hardening was large for alloys at either end of the phase diagram, and comparable with the Ta-W solution-hardening data of Ferris et a1.,8 the low work-hardening rate characteristic of niobium was sustained until a composition of Nb-85 pct MO had been reached. Associated with the peak yield stress ob-

Jan 1, 1969

By David L. Holt

The contribution of grain boundary shear to total elongation, CS/E&apos;, has been measured in an Al-Zn eu-tectoid alloy that was quenched from above the invariant temperature, then annealed at 250° C to a grain size of&apos; 1.8 p. At 250°C, ks/E&apos; is low at both high and low strain rates, but reaches a maximum, estimated as 60 pct at an intermediate rate of 5 X 10 per rnin. Rate sensitivity, as measured by the index m = a log a/a log E&apos;, follows the same trend, and furthermore the maximum values of m and -cur at approximately the same strain rate. This result, combined with the metallographic observation that boundary migration enhances boundary shearing, is interpreted as supporting a previous suggestion that the high rate sensitivity characterizing super-plasticity is the result of combined boundary shearing and migration. It is suggested that the latter event relieves stress concentrations at triple points, and smoothes boundaries so that stress is governed largely by a viscous boundary shear. GrAIN boundary shear has been considered in relation to superplasticity in several recent papers.&apos; The problem has been to explain the high strain rate sensitivity of flow stress, and the variation of rate sensitivity with strain rate (E&apos;) and grain size (L). The requirements for superplasticity, small L and high T, suggest the reasonableness of an approach to high rate sensitivity involving grain boundary shear. Further support came from experiments on the A1-Cu eutectic alloy,&apos; where it was found that strain rate sensitivity of cast material annealed to produce an equiaxed, micron-size grain is always low; taking as an index of rate sensitivity m = a log a/a log <, m < 0.3. However, m in hot-worked alloy of comparable grain size can be as high as 0.7. In the cast and annealed material, each phase is a single crystal, the only boundaries are interphase boundaries, and it is, consequently, geometrically impossible for boundary shear to contribute to deformation in any major way. Other observations (for hot-worked material) were a-L at constant (low) strain rates and indications that the rate of recrystallization was enhanced as strain rate increased. As a result of this work, it was proposed that high rate sensitivity arises from a deformation mode of boundary shear associated with boundary migration. Migration serves to relieve stress concentrations at triple points, and smoothes boundaries so that they assume properties of fluid films. On the other hand, the low rate sensitivity observed at high and low strain rates reflects deformation of bulk material. Measurement of the variation of grain boundary shear with strain rate and m have not yet been made. Such measurements are important, especially in view of a proposal, differing in detail from the above, that high m arises merely from a transition between a grain boundary shear mode of deformation at low rates to a transgranular mode at high rates.2&apos;4 In the present work, the contribution of boundary shear to total deformation is measured and in addition metallographic observations are made on surfaces of deformed specimens to look at the interaction between boundary shear and migration. The Al-Zn eutectoid alloy was chosen for its homogeneous, fine-grained structure, which is obtained readily without hot-working. It has also been the subject of a previous phenom-enologically directed study. EXPERIMENTAL Material. Compression specimens, cross section 4 by + in., length \ in., were machined from a sand-cast ingot of composition 77.5 wt pct Zn, 22.5 wt pct Al. (The melt was prepared from 99.9 pct Zn and 99.99 pct Al.) After homogenization at 375°C for 50 hr, the specimens were quenched in brine and removed before the heat evolution that accompanies de -composition of the high-temperature phase.5&apos;6 The resulting microstructure, see Fig. l(a), was too fine for grain boundary sliding to be easily studied; coarser structures were obtained by annealing for various times at 2 50°C. Annealing was terminated by a brine quench. Final average intercept lengths between all grain boundaries (both interphase and those lying in a phase), L, were: 0.5 p [annealed for 15 min, Fig. (a)], 0.8, 1.1, and 1.8 p [Fig. l(b)l. Testing Procedure. An Instron machine was used for most of the compressive deformation. Tests were of two types: those in which crosshead velocity was changed in steps to measure m as a function of strain rate15 and tests at constant velocity to a fixed (engineering) strain of -0.2 (20 pct). Stress reached a steady-state value (a) which was plotted, on a logarithmic scale, against log strain rate (E&apos;). An alternate and equivalent evaluation of m was to take the slope of the log o vs log 6 curve. Time at temperature before testing was 15 min. Strain rates covered by the Instron (4 x lo-&apos; to 4 x 10&apos; per min) were insufficient; at a higher rate of 5 x lo2 per min a gas-operated testing machine was used, the gas driving a piston to compress the specimen at a controlled velocity.&apos; To obtain points on the log a vs log E&apos; curve at low rates, specimens were compressed by a dead weight. strain rate was an average value computed by dividing strain at the end of test by loading time. In some tests strain was measured at fractions of the loading time; creep rate was found to be reasonably constant.

Jan 1, 1969

By G. R. St. Pierre, R. D. Blackburn

Oxygen contents of&apos; liquid-iron alloys saturated with oxides are analyzed. Minimum points observed in particular Fe-X-O systems can be predicled by a simple extension of first-order interaction methods. If minimum oxygen content occurs at N; where r is the ratio of metal to oxygen in the oxide phase. RECENTLY, wisher&apos; reported on solubility measurements of A1203 in liquid iron at 1580°C which support the earlier work of d&apos;Entremont, Guernsey, and chipman2 and Gokcen and Chipman. Swisher&apos;s diagram is reproduced in Fig. l. Minimum points in oxide solubilities have also been found in the Fe-Cr-0 system,4 Fig. 2, and the Fe-Ti-0 system,&apos; Fig. 3. Minima positions can be used to confirm approximately the measured first-order interactions, &, cgr, and E&~, in liquid iron and to deduce compositions of components of constant activity in the oxide phases. Consider the solution of Alz03 in liquid iron: for which an equilibrium constant can be written as: differentiating Eq. [2] with respect to Na~, the atom fraction of &l in the metallic solution, and noting that If the activities of Al and 9 are expanded by a first-order interaction model, then:

Jan 1, 1969

By J. Spreadborough, D. LaW. King, E. Anderson

Tmzsile tests were performed on Armco iron samples, at various ternpe.ralures and strain rates, ocer a wide range of grain sizes. Analysis of the data suggests that the plot of the lower yield stress, against d-1/2,where 2d is the acerage grain diameter, is not linear (as is often assumed) but is concave toward the d. axis over the range of d-from 7 to 53 . The different values of the parameters obtained by other workers can be explained, in part at least, by the observed curvature. This curvalure is shown to be consistent with a model of yielding based on dislocation pile-ups; however, the values of obtained by fitting our data to this model differ appreciably from the values generally reported. The equation proposed by Cottrell, viz.: is a plausible empirical fit to the experimental results. The purpose of this paper is to comment on the validity of the widely used linear relationship first proposed by all&apos; and Petch and coworkers2"4 between ay, the lower yield stress, and 2d, the average grain diameter, for bcc metals, viz.: Many workers, see Refs. 2 to 7 and Table 11, have fitted this equation to their experimental results and have obtained acceptable fits over the relatively narrow range of grain sizes used by most of them. Indeed, in some cases, so few data points were available that any more sophisticated fit would have been irrational. In most of the interpretations,&apos;-&apos; oi is thought to be a measure of the friction stress accompanying dislocation movement, and ky was originally inter- preted as a measure of the dislocation locking but is now believed by Cottrell" to be a function of the dislocation creation rate. In the "unpinning" theories, k, is equated to where od is the unpinning stress and 1 is the average distance from the boundary of the grain where yielding is taking place to the nearest dislocation source in an unyielded grain. Other considerations (see, for example, Refs. 11 and 12) lead to equations with a similar form to [I] where different meanings may be attributed to the parameters. While there are doubts as to the physical significance of the parameters i and k, they continue to be used by many workers; interpretations of the variations in the behavior of ferrite materials following certain treatments, e.g., aging,&apos;3 neutron irradiation,14 have been given frequently in terms of these parameters. Some theories of the mechanical behavior of bcc metals are based on this relationship. We have investigated experimentally the oy - d-&apos;lZ relationship for Armco iron over a wider range of grain sizes and with more data points than those given in published results. The analysis of our data suggests that the oy—d-&apos;" relationship is not linear but is in fact concave towards the d-&apos;I2 axis. RESULTS AND DISCUSSION The experimental work was carried out on 3-mm-diam Armco iron rods which were prepared by wire drawing from 5-mm-diam rods. By annealing in vacuum at temperatures between 7000 and 1200°C for various times, grain sizes from 7 to 20,000 grains per sq mm were obtained, the grains in all cases being regularly shaped. Grain sizes were measured by lineal interceptand by area methods; only specimens with Amax/A values of 3 to 6 were used in the Petch-Hall plots (where A is the average area of a grain and Amax is the area of the largest grain observed). For all the specimens used, the number of grains in a cross section exceeded 50, which should be adequate to avoid grain size effects.&apos;= Tensile tests were performed at 296", 219, and 17l°K, using

Jan 1, 1969

By P. C. J. Gallagher

A number of recmt determinations for the ratio of extrinsic to intrinsic stacking fault energy in fcc solid solutions are examined. Some of these arise from incomplete analyses which can yield only approxi?nate values for the ratio. Reliable results, on the other hand, obtained using extrinsic-intrinsic fault pairs, show that the extrinsic and intrinsic fault energies are essentially equal in several materials. There is some reason to believe that this finding is of general applicability to fcc elements and alloys. A wide range of values has been obtained for the relative magnitudes of the extrinsic and intrinsic stacking fault energies (yext and yint, respectively) in recently published studies in a variety of materials. In contrast, Hirth and Lothe&apos; using a central force model have shown that out to tenth nearest-neighbor interactions the perturbation in energy caused by both types of fault is the same. Although the model used is not completely valid in metals, there is nevertheless some indication that marked variations of yext/nnt should not be observed from one material to another. In early work in Cu-A1, Cu-Ge, Ni-Co, and stainless steel all the deformation faults observed in the electron microscope were found to be intrinsic in nature, which led to an attitude that the extrinsic fault energy must be considerably greater than the intrinsic. Extrinsic faulting arising from deformation has, however, more recently been directly observed in Au-4.8 at. pct n;~ Ag-6 at. pct Sn and Ag-8 at. pct sn; Ag-7.5 at. pct In and Ag-11.8 at. pct 1n;"&apos; pure silwer and Ag-0.5 at. pct ~n;&apos; and Cu-22 at. pct Zn, Cu-30 at. pct Zn, and Cu-7.5 at. pct ~1.l&apos; Multilayer loops containing extrinsic faulting have also been observed in quenched aluminum." While peak asymmetries in X-ray faulting probability studies were generally attributed to the presence of twins,Lelel2 has recently reinterpreted earlier X-ray data in Ag-Sb alloysU in terms of the presence of extrinsic faulting. The determinations of yeXt/yint made from the above studies are shown in Table I, with a brief description of the techniques employed. A number of the methods utilized are deficient in one or more respects, and the reliability of the values listed will be discussed. ~ele&apos;~ recognizes that his approximate determinations of yext/yint assumes equal numbers of extrin-sically and intrinsically faulted dislocations. It is well-known, however, that such an assumption is not at all justified since extrinsic faulting has but rarely been observed in samples studied in the electron microscope. The only conclusion that should be drawn from the X-ray results at present is that the total intrinsic scattering cross section (i.e., the product of the width of the intrinsically faulted dislocations with their density) is approximately ten times greater than for extrinsic faulting in these particular samples. An important point is that the relative magnitudes of the energies cannot be inferred from results of this type, unless the intrinsic and extrinsic faults form with equal ease. One must recognize that, although a formation barrier may restrict the amount of extrinsic faulting which occurs, this in no way implies that the extrinsic and intrinsic energies should be different. It is unlikely that a worthwhile estimate of the relative densities of extrinsically and intrinsically faulted dislocations can be made at the high deformations present in X-ray samples. ~oretto,&apos;~ from a statistical argument applied to the nonobservation of extrinsically faulted tetrahedra out of a large sample, concluded that yeXt/yint could not be less than -4.5. However, the present author feels that a high-energy formation barrier as just supposed also explains this finding satisfactorily and that no conclusion can possibly be drawn concerning the actual extrinsic stacking fault energy. The same argument also serves to explain the fact that extrinsic faulting has been relatively little observed in the electron microscope. Extrinsic-intrinsic node pairs and isolated extrinsic nodes were first reported by Loretto~ and subsequently by Ives and Ruff,&apos; Gallaher,&apos; and Gallagher and Wash-burn.&apos; Ives and Ruff&apos; found a wide spread in the ratio of extrinsically to intrinsically faulted area in the node pairs they observed, and drew the very tentative conclusion that yeXt/yint 2 2. They recognized that a straightforward comparison of the size of the faulted areas could provide no more than a qualitative result without a theoretical analysis of the dislocation geometry associated with extrinsic faulting. A theoretical

Jan 1, 1969

By R. O. Williams

The concept of biaxial pole figures which completely represent sheel textures is defined and an iterative least-squares solution given. The method has been applied to rolled copper, aluminum, and brass. The results show that the prior ideal textures are reasonably correct but incomplete. The major components in all three cases consist of a continuous range of orienta-tions roughly described as starting from (211) [111] continuing to (110) [112] to (110) [001], the details dif- THIS paper considers the problem of representing rolling textures in the most useful and comprehensible manner possible. A representation called a biaxial pole figure which completely represents such textures fering in all cases. For brass, in particular, the last part of the range is the most important. A minor cube component is established for the copper and aluminurn. The results were also analyzed by means of sets of three axial (inverse) pole figures to give similar, less-detailed results. The method of analysis is outlined. Such a representation is significantly less powerful than the biaxial method, but it has considerable utility in the calculation of anisotropic properties. is defined and an iterative least-squares solution is given. Such textures may be approximated by treating the principal directions as fiber axes to give three axial (inverse) pole figures. This representation is very useful for calculating anisotropic properties. New data for rolled copper, brass, and aluminum are given by both methods. In an axial pole figure the relative frequency or probability of a given physical direction (normally the

Jan 1, 1969

By R. W. Smith, M. E. Brookes

The temperature at which th: quenched 0&apos; (ordered bcc) phase transfo.rms to the ( (complex hexagonal) phase on heating has been examined for certain Ag-Zn and Ag-Au-Zn alloys using an electrical resistivity method. The transition temperature decreases by approxinzately 7°C as the zinc content is reduced by 1 at. pct. The critical temperature, Tc, for long-range order has also been measured for a number of Ag-Au-Zn alloys. Extrapolation to zero gold content suggests that Tc decreases by approximately 5°C per 1 at. pct reduction in zinc content. The 0 phase of the Ag-Zn system exists over a narrow range near the composition Ag zn,&apos; Fig. 1, and has a bcc structure which is disordered above 272°C. Slow cooling to temperatures below the range 274"/258"C allows the complex hexagonal phase, r° to form.2 This is the stable structure at room temperature.3 Upon quenching 0 -phase alloys from high temperatures, it is found that the 0 — (&apos; transformation is suppressed; but ordering takes place (i.e., 0 -0&apos;). This ordered structure can also be obtained by the room-temperature aging of cold-worked (0.4 Deformation of the 0&apos; phase gives rise to a fur- ther hexagonal phase ( (of nearly ideal axial ratio) which reverts to b&apos; within a few hours.= In view of this, it has been suggested that the equilibrium struc-

Jan 1, 1969

By Carl Altstetter, Roy Adams

Measurements of enthalpy changes and transformation temperatures me reported for the fcc -hcp marten-sitic transformation in pure cobalt single and multi-variant crystals andpolycrystalline specimens. From these measurements the free-energy difference between the two phases was calculated for both heating and cooling and for repeated cycles through the transformation. For heating of single crystals the average value of enthalpy change was 113 cal per mole but on cooling it was 84 cal per mole. This difference is interpreted in terms of lattice imperfections which are introduced during transformation. A calorimeter suitable for measurement of enthalpy changes of athertnal transformations is described. COBALT exhibits an allotropic phase transformation at around 417°C&apos; where an hcp phase (a = 2.507, c = 4.0686, c/a = 1.6228)~ stable at low temperatures transforms to an fcc phase stable up to 1495°C. The transformation has a hysteresis of about 30°C— the exact magnitude of the hysteresis depending on the number of transformation cycles, grain size, impurity content, and prior treatment.&apos;-6 The athermal character of the transformation and surface relief due to transformation shear indicate that the transformation is martensitic. Pole mechanisms for the transformation have been discussed by Sebilleau and Bibrin, Bilby, Seeger,&apos; and Basinski and Christian. These authors have proposed that the cooling transformation is effected by rotation of a Shockley partial dislocation around a pole dislocation with a screw component of 2a/3(111). Such a rotation would change the stacking of close-packed planes from the abcabc fcc stacking to the ababab hcp stacking sequence. This mechanism would predict a lattice correspondence of {111}fcc~~(0002~cp, have been observed. One would expect the heating transformation to occur similarly, involving dislocation movements on the (0002)hcp. However, a high density of pole dislocations and high dislocation ve- locity are required to account for microscopic observations. Furthermore, the high back stress developed on the Shockley partial dislocation as it rotates toward the sessile dislocation associated with it makes it doubtful that this is in fact the transformation mechanism. A mechanism for spontaneous nucleation of partial dislocations1*l2 seems more reasonable. If a single crystal of cobalt is cycled through the transformation but never heated above 600°C, it will remain single."13 However, if the specimen is heated through the transformation and held for a short time at or above 1000°C before cooling, the cooling transformation usually involves all four {lll}fcc habits, resulting in neighboring orientations of hcp differing by 70.5 deg. This condition is termed multivariance and has been observed by Bibring and sebilleau5 and Nelson and ~ltstetter.&apos; The latter authors used single crystals of cobalt grown in an electron beam zone refiner. They proposed that the strongly directional cooling caused the initial cooling transformation to occur on the {lll)fcc most nearly perpendicular to the temperature gradient. Transformation shear on one set of {lll}fcc planes immobilized dislocations on the other {lll}fcc planes involved in the initial transformation. Since there is only one (0002)hcp plane orientation, the product of subsequent heating transformations could have no more than two variants—the original fcc orientation or its twin. If, however, the specimen was annealed at a high temperature, such as 1000°C, there would be relaxation of dislocations into low-energy configurations, and in the absence of a sharp temperature gradient transformation on all four (111 Ifcc planes could occur. If a dislocation mechanism is responsible for the transformation, the perfection of the lattice should affect the reversibility of the transformation. Mutual constraints of neighboring grains in polycrystalline material would inhibit dislocation movement resulting in increasingly sluggish transformation. Indeed, Nelson and Altstetter found the M, to decrease and the A, to increase in going from single crystals to multi-variant specimens to polycrystals. The effect is enhanced by decreasing the grain size of a solid specimen or a powder.6&apos;14 Data on the free-energy difference necessary to initiate the transformation gives information about the driving force of the transformation. This is an important consideration in the understanding of the transformation mechanism. The free-energy change associated with the transformation of the hcp phase to the fcc phase at some temperature T different from the equi-

Jan 1, 1969

By L. R. Velho, N. A. D. Parlee, J. Gani

THE unsteady-state type of gas-liquid metal diffusion cell1 has found considerable application.2"4 Cells of this general design can function as steady-state cells if allowed to operate long enough to reach steady state. This report tells of some success in the adaption of this type of cell for steady-state work, using the 0-Ag system in which the mass transfer of the gas "species" is basically controlled by diffusion in the liquid. The gas, e.g-., O2, is maintained in the cell tube&apos;-3 at 1 atm pressure, Fig. 1, by buret and sensitive oil manometer. The gas, after diffusing through the stagnant metal, escapes at the annular metal surface around the tube at a lower constant partial pressure, in this case that of O2 in slowly flowing air, 1 atm.

Jan 1, 1970

By A. H. Larson, R. J. McClincy

ALTHOUGH arsenic has a very high vapor pressure and vacuum distillation appears to be a likely method for its removal from lead, the published literature contains virtually no information concerning the vacuum removal of arsenic from lead. Caldwell, Spendlove, and St. Claire1 mention arsenic in their investigation of the removal of volatile metals from lead by vacuum distillation. They do not, however, give any data for arsenic removal or refer to any actual experimental work involving arsenic dissolved in lead. Moriyama, Kozuka, and Miura2 have determined the activity of arsenic in dilute As-Pb alloys in the temperature range from 450" to 600°C using a closed galvanic cell. They found that the activities of both arsenic and lead showed a positive deviation from ideality at 600°C. In view of the lack of experimental data regarding the vaporization of arsenic from As-Pb alloys, a limited vapor pressure study was made on liquid alloys containing from 0.5 to 3.3 wt pct As in lead at 703°C. The pressure of As4(v) above the alloys studied was determined from weight-loss data collected by means of the inert-gas saturation method. The experimental apparatus and procedure used were similar to that discussed by Alcock and Hooper9 with modifications as described by the authors., The technique involved was one of passing a known volume of inert gas over the alloy to be studied in a known amount of time and determining the loss in weight of the sample. Because of the low vapor pressure of lead at 703"C, the observed weight loss could be attributed solely to the vaporization of arsenic as the tetratomic molecule AS43 Measurements of the apparent vapor pressure were repeated at different inert-gas flow rates until from three to five values were obtained which were independent of inert-gas flow rate. This value of the apparent vapor pressure was taken to be the equilibrium vapor pressure of the alloy under consideration. The vapor pressures measured in this investigation have been converted to the activities of arsenic in As-Pb alloys, Table I, by use of the data compiled by Elliott and Gleiser5 for the vapor pressure of pure arsenic. The standard state for arsenic was chosen as the pure, hypothetical, supercooled liquid. The activity of arsenic was calculated from the fourth root of the ratio PAs,/PAS,. The low magnitude of the vapor pressures given in Table I explains the difficulty en- countered by earlier workers in successfully vacuum distilling arsenic from very dilute As-Pb alloys. The data shown in Fig. 1 indicate that the As-Pb system behaves ideally. The apparent outlier represented by the alloy containing 1.43 mol pct As is a result of the fact that the pressure of As, above the alloy was barely detectable by the experimental procedure used in this investigation. Because of this, the apparent vapor pressure determined for this alloy could be in considerable error. Moriyama, Kozuka, and ~iura&apos; have reported that arsenic shows a positive deviation from ideality in dilute solution in lead. However, details of their results have not been made available. This research was made possible by a grant from the National Science Foundation (GK-196) for which the authors are very appreciative.

Jan 1, 1970

By John D. Meahin

THE use of digital methods for generating crystallo-graphic data is well-established and many programs are now available. Transmission electron microscopy usually requires a knowledge of the electron diffraction pattern which is obtained by plotting a planar section through reciprocal space. With cubic symmetry these sections are very easily produced, but with hexagonal and lower symmetry systems considerably more labor is involved. Johari and Buchanan1 have written a Fortran program for generating standard projections and along similar lines we have produced a short but completely general program for generating any section through reciprocal space. The required inputs are the lattice parameters and angles for the real crystal. The Miller indices of the direction [U, V, W] parallel to the electron beam are then specified and the program will generate the Miller indices of the plane normals perpendicular to [U, V,, W] up to some specified integer. A subroutine can be inserted to test for forbidden reflections if desired. We have used such routines for fct and hcp crystals. As each permitted index is generated it is printed or punched out and no storage arrays are utilized in the computer. The normal diffraction pattern corresponds to the zero-order Laue zone, but with thin crystals or crystals of large lattice parameters the higher-order Laue zones may contribute to the diffraction pattern. Accordingly the program will generate successive Laue zones and project them onto the zero-order zone. The output of the program first lists the zone axis [C, V, W] and the Laue zone, and then gives a list of permitted reflections and the corresponding XP and YP coordinates of the reciprocal lattice point in angstroms-&apos;. In addition, ZP, the perpendicular distance of the reciprocal lattice point from the (U, V, Ur) plane in reciprocal space is given, as is the reciprocal interplanar spacing. In the case of the zero-order Laue zone ZP is zero. A diffraction spot from the higher-order Laue zones will be very slightly displaced from the computed coordinates as its position in an actual pattern is given by projection along the diffracted beam2 and not along [u, V, w]. For any given electron wavelength this correction could be readily incorporated into the program, but as it only amounts to -1 pct it was decided to leave the program in its most general form, i.e ., a computation of points

Jan 1, 1970

By Frank A. Crossley

The work described has one serious shortcoming: grain size was not monitored during heat up to the temperature (1675°F) of isothermal anneal. The chief obstacles to p grain growth in titanium a-ß structures are the a grains. Heating a structure such as that shown in Fig. 1 to a temperature close to ß transus causes dissolution of a grains in order to adjust the a/ß ratio, compare Figs. 1 and 2. During this process there is a concomitant growth of the ß grains—otherwise ß grains would have to be nucleated in order to adjust the a/ß ratio. When the annealing temperature is reached the a/ß ratio stabilizes and this initial phase of ß grain growth ceases. After an incubation period growth resumes as described. Some 0 grain boundaries can be clearly seen in Fig. 1. (Skilled metallography commonly produces photomicrographs which show more structural detail than direct observation.) These boundaries suggest that the average ß grain size is approximately 0.002

Jan 1, 1970

By R. G. Vardiman, M. R. Achter

THERE has been interest recently in the conditions under which dislocation pipe diffusion may be observed. In order to extend the measurements to temperatures below Tm/2, where pipe diffusion becomes more important, a chemical sectioning technique was developed for silver single crystals which makes possible the removal of layers of 100A or less. The procedure is briefly as follows. Silver single crystals of 99.995 pct purity were cut in the form of discs t by 4 in., electropolished, and electropolated with Ag110 to about 1000A thickness. The thickness was determined by calibrating the activity with the weight of heavier platings, up to 10,000A. Both diffused and undiffused samples were sectioned in a two-step process. Reaction with a solution of iodine in alcohol formed a thin, even layer of AgI, which was then dissolved in a KCN solution. The reaction rate of the iodine solution varied slightly over a period of time, so that the thickness of the stripped layers, while quite even and regular for a given specimen, ranged from 65 to l00W for different specimens. This variation was checked by using a thickly plated standard with each run. Layer thickness was determined from undiffused samples by the point where the layer activity drops to half the maximum. This maximum intensity also provides, with appropriate corrections, the initial concentration per layer co. Because of the small penetration distances, it is necessary to use the exact solution of Fick&apos;s law for a source of finite thickness.&apos; For a plating of thick- where c is the concentration at depth x. flj the error function, D the apparent diffusion coefficient, and t the time. The diffusion coefficient was obtained from the concentration-penetration data by extrapolating to x = 0 where c/co = erf h/2(Dt)1/2 Enough points were taken to impart confidence in the accuracy of the intersection, generally about ten layers. Four temperatures were used as in Table I. For best accuracy, t and h were chosen to give values of the parameter (Dt)1/2/h between 1.0 and 1.7. A typical concentration-penetration curve is shown in Fig. 1. The diffusion coefficients calculated from Eq. [I] are plotted in Fig. 2. For comparison, the high-temperature data of Tomizuka and sonder 2 which go down to 630°C are plotted as the solid line 2(a) from their expression D = 0.40 exp (-44,090/RT). Also for comparison, the lowest temperature point of Hoffman and Tumbull3 is plotted. It is apparent that our data diverge appreciably from the high-temperature extrapolation by 373°C. A better straight line fit for the low-temperature portion is obtained by subtracting the extrapolated volume diffusion coefficient from the apparent. or measured coefficient, and plotting the difference, curve (h) of

Jan 1, 1970

AN intermetallic compound, Ni3A1, has an ordered fcc structure of type Ll2, and shows peculiar dependence of the yield stress upon temperature; i.e., the yield stress increases by a factor of six upon raising the temperature from 77" to 900K1, 2 This compound is technologically important, since many nickel-base superalloys owe their high-temperature strength to the peculiar yield stress behavior of Ni3Al. The only study of the elastic behavior of this compound was made by Davies and Stoloff,1 who determined Young&apos;s modulus of poly crystalline Ni3A1 between 300" and 730°K. The determination of single-crystal elastic constants of Ni3A1 is therefore of interest in connection with dislocation dynamics and is reported in this paper. A single-crystal specimen, 1 by 1 by 3 cm, was cut from an ingot generously supplied by Dr. B. H. Kear of Pratt & Whitney Aircraft. Following initial machining with a Servomet and a surface grinder, the specimen was etched and annealed at 1100°C for 5 hr in vacuum followed by furnace cooling. Two parallel faces were oriented normal to within ±l deg of a [I101 crystallographic axis by the back-reflection Laue technique. The parallel faces were hand-lapped, etched, and polished by the usual metallographic procedures. Final thickness along the [I101 axis was (0.9325 * 0.0005) cm. Chemical analysis gave an average composition of 87.35 pct Ni. Total impurity content is esimated to be no more than 0.1 pct. The elastic constants were calculated from measurements of ultrasonic waves which were propagated along the [110] axis. A longitudinal wave and two shear waves whose displacements are aligned along the [ 110], [li~], and [001] directions, respectively, are necessary in order to completely specify the three elastic constants. Two 3/6-in. quartz transducers were bonded to the parallel faces of the sample with ~ac-seal.3 Although this bond was sensitive to thermal shock, it performed satisfactorily over the entire temperature range for both longitudinal and shear wave propagation. A frequency of 5 mHz was employed in the method of Williams and Lamb4 in order to measure the absolute value of the ultrasonic velocity. The pulse-overlap technique of Mcskimin5 was also used at this frequency in order to determine the shift in the ultrasonic velocity

Jan 1, 1970

By J. Kittl, D. Arias

THE decomposition on cooling of the high-temperature ß bcc phases in copper- or silver-based binary systems usually takes place by a martensitic. massive, bainitic, or pearlitic reaction depending upon the particular conditions of each system. The AgAl system is one of these systems in which a massive or a martensitic transformation can occur upon cooling from the 3 phase field. Recently Hawbolt and Brown1 observed both massive and martensitic transformation products in a 22.7 at. pct A1 alloy. In the present work the massive and the martensitic transformations were investigated in a number of alloys for the composition range between 23.2 and 27.9 at. pct Al. The alloys were prepared using high-purity silver, 99.999 pct, supplied by ASARCO and aluminum, 99.999 pct, supplied by ALCOA. The metals were melted using a graphite or a sintered alumina crucible which was sealed in quartz tubes under an argon atmosphere. The alloys Were remelted to reduce segregation and homogenized in the 13 phase field for 24 hr. The weight of the alloys after homo-genization compared with the initial weight indicating the alloy composition to be within k0.1 pct of the in- tended composition. Chemical analysis of several samples confirmed the estimated alloy composition. All metallographic observations were performed on samples electropolished with ac current using a 10 pct solution of KCN and a stainless-steel electrode. The samples were cut into -1-mm-thick slices, polished, heat-treated in the ß phase field, and quenched in air, ice water, or iced brine. Some heat treatments consisted of a 2-min anneal carried out in air to allow maximum quenching speeds. Other samples were heat-treated in a vacuum of 10"4 torr and quenched using a helium blast in a quenching apparatus described elsewhere.&apos; In both cases, no appreciable losses of silver or aluminum were noted at the sample surface by sectioning and electropolishing. Table I summarizes the microstructure resulting from the various quenching treatments. The composition of the alloys investigated is also indicated on the equilibrium diagram in Fig. 1. The <, hcp phase, typical of a massive ß — cm, transformation, was observed in all alloys. A minimum temperature of 450°C was estimated for this transformation based on preliminary cooling experiments. the results being included in Fig. 1. In these

Jan 1, 1970

By J. P. G. Farr, R. Brownsword

THE role of solute segregation in the formation of cellular solidification substructures in tin and its dilute alloys is well-established, see, e.g., Ref. 1. Segregation has been shown to persist during cooling, enabling solidification structures to be studied from sections taken at some distance behind the interface. In the present work, a single crystal of commercial nickel, 99.965 pct, was examined in this way. The crystal was cut from the center of a rod given a single pass in an electron beam floating zone melter. Polished sections of a nickel specimen taken normal to the growth direction showed a very fine precipitate phase, the distribution of which varied over the section. The identification of the phase proved difficult because of the small amount present and the small particle size, about 1 p: but it was shown by probe microanalysis to contain only nickel and oxygen in detectable concentrations and was probably nickel oxide, NiO. Bulk analysis of the material before melting showed there to be only 3 to 4 ppm of oxygen present, thus demonstrating a very considerable segregation concentration effect. In some areas of the section the precipitate formed a discontinuous hexagonal network suggesting decoration of the cellular boundaries known to be present in the sample2 whereas in a restricted region the precipitate formed small clusters. Occasionally it could be seen that the clusters were at the intersections of an hexagonal network of cellular dimension. It was suggested3 that this was the result of enhanced segregation to the cell boundary intersections whereas general cell boundary segregation was insufficient to give a precipitate. Enhanced nodal segregation has since been demonstrated in a number of systems.1, 4-8 The development of a suitable electrolytic etching technique (perchloric acid 20 pct v/v; ethyl alcohol 70 pct; glycerol 10 pct; current below electropolishing plateau; 1 to 2 sec etching) suggested the association of the phase with regions of solute segregation (where ko < 1); in these regions anodic attack produced grooves or depressions. In a study of the variation of solidification substructures with degree of constitutional supercooling, Biloni et a1.&apos; appear to have used standard growth conditions and varied the solute concentration. They were able to produce in a series of individual tin crystals examples of substructure ranging from planar interface through various cellular structures to den- Fig. 1—Electroetched section taken normal to the rod axis; the center of the rod lies to the left and the periphery to the right of the micrograph. The variation of structure across the section is evident. Magnification 60 times. drites. It was possible in the present nickel crystal to observe a continuous range of substructures varying with degree of supercooling across a single section as shown in Fig. 1. Growth rate, 13 mm per min, and temperature gradient were essentially constant; the variation in structure is thought to be due to a radial gradient in solute concentration ahead of the solid interface. The liquid at the interface is likely to have been richer in solute toward the periphery of the zone, the result of curvature of this interface. The type of substructure was seen to vary with increasing constitutional supercooling as follows: a) region free of precipitate. top left, Fig. 1: 6) region of nodal precipitates which became arranged in hexagons on passing from the center of the rod: c) irregular hexagonal cells with incomplete boundary precipitation; d) regular hexagonal cells of decreasing size with complete boundary precipitation. Fig. 2 shows the transition from stage 6 and Fig. 3 shows the structure in stage d. Within stage 0, the range of conditions over which irregularly positioned nodes occur appears to be small and the nodes are soon recognizable as taking up positions at the intersections of an hexagonal network as the supercooling increases.

Jan 1, 1970