Search Documents

By M. R. Geer, H. F. Yancey

The importance of the size composition of coal is reflected in the difference in price of the various sizes of the same coal and in the large number of primary sizes and mixtures of sizes produced by the modern preparation plant to meet the demands of a market that in late years has grown increasingly conscious of coal size. The importance of size in the industrial and domestic uses of coal has its counterpart in the role played by size composition in the laboratory examination of coal. Investigation of many of the physical properties of coal in their relation to its uses requires an evaluation of size composition. In fact, the Standards on Coal and Coke issued by the American Socaiety for Testing Materials in 1936 contains 12 standard methods of testing that involve some use of size composition. The screen analysis is, of course, the standard method of determining size composition, whether the material is coarse run-of-mine coal or fine pulverized fuel. Custorriarily, the analysis is reported as the weight percentages retained on or passing each of a series of testing screens, the number of which may range from only two or three to as many as 20. When more than two or three sieves are used, which is usual, the number of weight percentages obtained is so great as to make the analysis difficult to comprehend. Direct comparison of analyses made 011 the same sieves is hard, and comparison of analyses covering the same range of sizes but made on different sieves is next to impossible. Consequently, a frequent purpose of sizing tests-—-correlation of size with properties and charactcristics related to size-—is rendered difficult. Less cumbersome means of expressing size composition have been attempted with various degrees of success. An average particle size, calculated by any of several formulas, is useful for some purposes, also the weight percentage retained on a single sieve finds some application as a

Jan 1, 1938

By T. W. Guy

During the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, air-dried moistures, or oven-dried moistures. For most of the reports it was necessary to estimate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the products should be measured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they sometimes include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture. The Problem We know that pieces of coal have a capacity for holding water: (1) inside themselves, which is a natural characteristic of the bed from

Jan 1, 1938

By T. W. Guy

During the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, air-dried moistures, or oven-dried moistures. For most of the reports it was necessary to estimate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the products should be measured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they sometimes include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture. The Problem We know that pieces of coal have a capacity for holding water: (1) inside themselves, which is a natural characteristic of the bed from

Jan 1, 1938

By G. B. Gould

Every mathematical statement of a measure of anything (as distinguished from a count') is followed by a qualification—always implied if not explicity stated—-that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accuracy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applications—and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this question of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject themselves. There is great need for more widespread understanding of what lias been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments. Determining Deviations in Quality It is necessary at the outset to distinguish between: (I) the accuracy with which one test indicates the quality on one lot of coal; and (2) the accuracy with which a test of one lot of coal represents the average quality of a commercial product, of which the buyer will presumably receive a series of shipments—perhaps many thousands of tons. It is necessary to make this distinction because coal is a variable material—a heterogeneous mixture of a variety of components—the quality of which will vary from one lot to another. Therefore an absolutely accurate determination of the quality (if that were possible) of one lot of a coal is an

Jan 1, 1938

By G. B. Gould

Every mathematical statement of a measure of anything (as distinguished from a count') is followed by a qualification—always implied if not explicity stated—-that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accuracy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applications—and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this question of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject themselves. There is great need for more widespread understanding of what lias been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments. Determining Deviations in Quality It is necessary at the outset to distinguish between: (I) the accuracy with which one test indicates the quality on one lot of coal; and (2) the accuracy with which a test of one lot of coal represents the average quality of a commercial product, of which the buyer will presumably receive a series of shipments—perhaps many thousands of tons. It is necessary to make this distinction because coal is a variable material—a heterogeneous mixture of a variety of components—the quality of which will vary from one lot to another. Therefore an absolutely accurate determination of the quality (if that were possible) of one lot of a coal is an

Jan 1, 1938

By D. L. Gardner, H. L. Barr

The following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geologists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions. Location of Area and Scope of Work San Mauricio Mining Co. controls a group of 113 claims that lie immediately north of the town of José Pafiganiban (formerly Mambulao), Camarines Norte, Luzon, P. I. (Fig. 1). Exploration work commenced in the spring of 1934; active development began in the fall of that year and has continued to the present date. Mill construction was begun Ocl,. 15, 1935, and production started March 10, 1936. Total production to June 1, 1939, is P10,499,105.15 ($5,249,552.57).

Jan 1, 1941

By D. L. Gardner, H. L. Barr

The following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geologists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions. Location of Area and Scope of Work San Mauricio Mining Co. controls a group of 113 claims that lie immediately north of the town of José Pafiganiban (formerly Mambulao), Camarines Norte, Luzon, P. I. (Fig. 1). Exploration work commenced in the spring of 1934; active development began in the fall of that year and has continued to the present date. Mill construction was begun Ocl,. 15, 1935, and production started March 10, 1936. Total production to June 1, 1939, is P10,499,105.15 ($5,249,552.57).

Jan 1, 1941

By A. J. M. Ross

Backfilling of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35" to 40' to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1940

By A. J. M. Ross

Backfilling of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35" to 40' to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1940

By W. A. Scheuch, J. Walter

Ordinarily secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered'metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must, just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product. Secondary Copper Used for Wire Bars Only clean secondary copper of the grades known to the trade as Numbers 1 and 2 are melted for wire-bar manufacture. This material, supplemented by that obtained from various manufacturing processes

Jan 1, 1930

By Francis N. Flynn

Many excellent papers, descriptive of the milling and smelting of every kind of commercial ores, the refining of virgin metals, the casting into various shapes demanded by the trade, the rolling into shapes best suited to the factory machinery and the making of composition alloys to suit every requirement have been issued by the many technical societies dealing with non-ferrous metals. It is a wonderful collection of papers, of which the mining and metallurgical engineers may well be proud, but strange as it may seem, metallurgists in general appear to take the stand that when they have delivered suitable alloys to the foundry and rolled products to the factory their duty to write papers has ceased, at least in so far as the A. I. M. E. is concerned. Still we read in the daily papers that the mining companies are absorbing metal-manufacturing industries. The purpose of this paper is to describe the reclaiming of non-ferrous scrap metals at manufacturing plants, taking as an example the automobile industry. Collection and Disposition of Scrap Until about five years ago, much of the factory scrap, with little or no preliminary treatment, was sold to secondary-metal smelters. Of late years the factory salvage department has become an important part, of the plant in reclaiming everything of value and incidentally does much of the work formerly done by the smelters. Like most good things, it is sometimes overdone, and much work is done at the factory with inexperienced men that could be done much better by experienced skilled labor at the custom smelting plants. Employees of the salvage department collect the waste products in all departments at the source and in that way avoid much contamination. Every reasonable precaution is taken to keep the scrap clean. It is hand-sorted, cut, burned, magnetized, concentrated, separated or compressed, as the case may be, preparatory for re-use in the plant or for selling to others.

Jan 1, 1930

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

By H. M. St. John

Like every present-day manufacturer, the brass foundryman is faced with the necessity of reducing the cost of his finished product without impairing its appearance or quality. He must use every economy that the progress of art and science puts at his disposal and should also be alert to profit by any peculiarity in his own situation or the nature of his product that may give him an exceptional advantage. Much can be accomplished by the adoption of labor-saving equipment and improved methods of melting, molding and handling. Control of pouring temperature, study of defective castings and their causes, laboratory control of molding sand and core mixtures, the use of less expensive alloys, all contribute to the desired end. Assuming that the composition of the alloy is already as inexpensive as the character of the casting will permit, still further savings can be made by the intelligent purchase and utilization of the metals needed to produce the desired analysis. Functions of Secondary and Virgin Metals in Casting Brass It is no longer a general assumption among foundrymen that quality castings must be made from an "all virgin" mix. If suitable secondary metals can be obtained more cheaply it is wasteful to use any larger proportion of virgin metal than is required to produce castings of the desired properties. To follow such a course, however, imposes upon the foundryman a heavier obligation than was formerly the case, to make sure by test and inspection that his castings really are of the desired quality. So long as he used the most expensive grades of metal and his melting practice was reasonably correct he was not obliged to give much thought to the quality of the metal in the castings. If he is to use secondary metals he must, in order to retain the confidence of his customer, examine these metals very carefully before use, exercise scrupulous control over his melting and pouring conditions and examine his castings closely. These statements apply more particularly to the jobbing foundry. The foundry department in a manufacturing plant is in a somewhat

Jan 1, 1930

By W. M. Bertholf

In 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral call make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory)" as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,' but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1947

By W. M. Bertholf

In 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral call make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory)" as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,' but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1947

By A. W. Faheneald, Lewis S. Prater

By taking advantage of the fundamental difference between screening and classification—namely, that specific gravity has no effect on screening but is one of the important factors in classification—a combination of the two may be used as a process of mineral concentration. Although this fact is not new, so far as is known it has had little or no commercial application. The scheme is not presented now as a process for producing finished products but rather as a preliminary operation rejecting part of the barren material from an ore before it is subjected to more costly treatment. That is largely the function of the new heavy-media concentration processes that have been widely accepted. Original installation costs for the present sink-float processes are relatively high, however, which confines their use to operations where large tonnages are handled. Sink-float has been successful on only the relatively coarse (approximately plus 10-mesh) portion of an ore, and it is in this same range that classification screening can function most satisfactorily. Theoretically, there is no upper limit to the size of particles that can be handled in a sink-float operation, but the degree of liberation in the very large pieces usually limits this. With classification screening, particles from % to % in. would be the largest that could be handled, but the lower range could be extended somewhat below 10 mesh. In order to take full advantage of the difference in specific gravities of the minerals being separated, sorting in the classifier should be under as extreme hindered-settling conditions as possible. Laboratory tests have been made on a galena ore and on an artificial mixture of quartz and magnesite to determine the separations that may be expected. Although more than one scheme may be followed, in these tests the separations were made by cutting the underflow from the classifier as a concentrate and then screening the overflow. The screen oversize was rejected as a tailing. Classification was done in a hindered-settling teeter column and screening was done by hand, using the standard 4 2 series. The accompanying flowsheet gives the testing procedure followed.

Jan 1, 1947

By A. W. Faheneald, Lewis S. Prater

By taking advantage of the fundamental difference between screening and classification—namely, that specific gravity has no effect on screening but is one of the important factors in classification—a combination of the two may be used as a process of mineral concentration. Although this fact is not new, so far as is known it has had little or no commercial application. The scheme is not presented now as a process for producing finished products but rather as a preliminary operation rejecting part of the barren material from an ore before it is subjected to more costly treatment. That is largely the function of the new heavy-media concentration processes that have been widely accepted. Original installation costs for the present sink-float processes are relatively high, however, which confines their use to operations where large tonnages are handled. Sink-float has been successful on only the relatively coarse (approximately plus 10-mesh) portion of an ore, and it is in this same range that classification screening can function most satisfactorily. Theoretically, there is no upper limit to the size of particles that can be handled in a sink-float operation, but the degree of liberation in the very large pieces usually limits this. With classification screening, particles from % to % in. would be the largest that could be handled, but the lower range could be extended somewhat below 10 mesh. In order to take full advantage of the difference in specific gravities of the minerals being separated, sorting in the classifier should be under as extreme hindered-settling conditions as possible. Laboratory tests have been made on a galena ore and on an artificial mixture of quartz and magnesite to determine the separations that may be expected. Although more than one scheme may be followed, in these tests the separations were made by cutting the underflow from the classifier as a concentrate and then screening the overflow. The screen oversize was rejected as a tailing. Classification was done in a hindered-settling teeter column and screening was done by hand, using the standard 4 2 series. The accompanying flowsheet gives the testing procedure followed.

Jan 1, 1947

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By Helmut Thielsch

In recent years an ever increasing amount of interest has been directed toward research studying the principles and various applications of sonic and supersonic waves. Though still in their early stages of practical development, sonic vibrations are already used in the emulsifi-cation and degasification of liquids. Metals exposed to sonic or ultrasonic vibrations while solidifying show a considerable amount of grain refinement. Often sound waves are applied instead of radiography to test engineering materials for internal cracks and flaws.' In the field of pure research these waves are used in dispersion and also in coagulation of particles or liquids in gaseous or, under certain conditions, in other liquid systems. In the settling and thickening of slurries considerable time is necessary to compress the solid particles and to squeeze out the liquid to obtain as low a dilution (liquid to solid ratio) as possible. Various methods have been developed to increase the amount of coagulation of the very fine solids (colloidal or semicolloidal) and to shorten the over-all time. The addition of small amounts of electrolytes and the warming of the suspension represent merely the more important techniques. Some of the effects of supersonic vibrations have been reported previously. From preliminary studies, therefore, it was hoped that by application of sonic vibrations it would be possible to reduce the time required to thicken such materials to a specific dilution, as well as to thicken to lower ultimate dilutions than could be obtained by quiescent settling alone. By increasing the volume thickened per unit time—i.e., improving the plant efficiency— great savings in equipment and time would be obtained for industrial processes. Also, faster settling rates should result if coagulation of particles could be increased. Experiments have been conducted for a period of several months in the Allis-Chalmers laboratory to study the effect of sonic vibrations on settling of particles of different sizes and concentrations. Apparatus The sedimentation apparatus used in these experiments is illustrated in Figs. I and 2. The essential features are the stationary field coil and the movable voice coil. Both windings are placed around a solid iron core. A leather diaphragm connected to the steel frame holds the voice coil in place. A brass rod is fastened to the voice coil with a metal disk connected to the other end. This disk is sealed to the lucite cylinder with a flexible rubber diaphragm. The lucite tube is 17 in. long; its inner diameter is 2½ in. and the wall thickness is ¼ in. The tube is calibrated on the outside in 10 c.c. divisions for a total of 1000 cubic centimeters.

Jan 1, 1947