Search Documents

By Albert J. Phillips

When brasses containing from 61 to 62.5 per cent. copper are very rapidly cooled from temperatures near their melting point to below 0" C., unusual results are obtained. These results are quite unexplainable from a consideration of the old copper-zinc constitutional diagram but they can be satisfactorily explained by means of the diagram revised by Genders and Bailey1 (Fig. 1). Experiments on a 60/40 Brass If an alloy containing 60 per cent. copper is heated to any temperature between approximately 760' C. and its melting point, it will consist entirely of beta. Upon slowly cooling, alpha will start to separate just below 760" C. Since this alpha will contain nearly 65 per cent, copper, the beta will be impoverished by its separation. As the temperature decreases the composition of the separating alpha will approach approximately 61 per cent. and the beta in contact with the alpha will maintain an equilibrium composition approaching 54.5 per cent. copper. If the rate of cooling is extremely slow, especially at the lower temperatures, stable equilibrium will be established by diffusion through the alpha and beta so that eventually 85 per cent. of the alloy will consist of alpha containing 61 per cent. copper, while 15 per cent. will be beta containing 54.5 per cent. copper. With a faster cooling rate diffusion cannot keep apace and the constituents will be cored, the alpha varying from 65 to 61 per cent. copper and the beta from 60 to 54.5 copper. In this case the amount of alpha will be less than 85 per cent. and the beta will be increased correspondingly. The general structure thus obtained is illustrated in Fig. 2. When a more rapid rate of cooling is effected by quenching in water, the alloy is retained largely in the beta form. However, the crystals of beta are usually outlined with dark fringes which at high magnifications are found to be very fine alpha-beta structures almost martensitic in appearance. The separation of this fringe can be greatly suppressed

Jan 1, 1930

By Cyril Stanley Smith

Although alloys of copper and silicon were examined several years ago,' and their excellent mechanical properties were shown, it was not until C. B. Jacobs 2 introduced manganese in small quantities to the alloys that they became of commercial importance. A few years ago The American Brass Company took over the patents and commenced to manufacture the alloy under the name "Everdur." The present study of the constitution of the ternary system was undertaken in order to reach a fuller understanding of the behavior of the alloy. Review of Previous WORK on the BinaRy Systems There have been no papers published dealing with the constitution of the ternary system, although some tests of the mechanical properties have been described," which indicate that there is a change in solubility with temperature. Copper-silicon System The copper-silicon system has been studied in detail by the author and is described in two papers published in 1928.V he portion of the diagram up to 8 per cent. silicon, as determined by this research, is reproduced in Fig. 1. The author's previous papers include a complete review of the work of other investigators and it is not necessary to deal further with this system here. Copper-manganese System The copper-manganese system has been investigated by several workers, notably Lewis,5 Wologdine,6 Sahmen7 and Schemtschuschny,

Jan 1, 1930

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received little study on the part of wire mills, particularly those that have commenced operations in the last few years. Two Types of Defects One type of defect is generally known in this country as "check marks;" in Europe it is termed "crowfeet" (Fig. 1). This defect occurs in the surface of the copper wire, in the form of V's, which are always

Jan 1, 1930

By C. T. Eddy, R. W. Drier

The conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in properry. or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest. Effect of Direction of Drawing In 1928 some work was done on hard-drawn copper wires to determine whether wire drawn in a continuous machine (that is, all in one direction) would have a different structure from wire that had a reversal in direction at some stage of the drawing process. The diffraction spectra obtained indicated that as the position of the wire rayed approached the core, a preferential crystal orientation existed, and that the closer to the core the more preferred was the orientation. The data obtained partly corroborated the work done by Schmidt and Wassermanl and by Clark.2 Samples Used in Following Investigation The samples selected for use in both the diffraction work and the resistivity measurements were taken from Nos. 6, 8, 10 and 12 gage

Jan 1, 1930

By Earle E. Schumacher, W. C. Ellis, John F. Eckel

Copper-calcium alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiensl have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1930

By C. H. Mathewson, Kent R. Van Horn

Copper and the copper-base solid solutions readily form twin crystals when plastically deformed at a suitably elevated temperature or annealed after cold deformation. In fact, no feature of the microstructure of these materials is more prominent or characteristic than these straight-sided bands or simple lines of division which sometimes come from groups of thin polysynthetic lamellae, penetrating part way or wholly through the parent grain substance, but often divide the grain into a few or perhaps only two crystallographically related parts. Nearly always the bands as seen in the usual microscopic examination of a specimen come into vivid contrast with the adjacent crystalline material owing to the inherent difference in orientation. Bands which under special conditions of orientation cannot be seen with vertically incident light are often visible under oblique illumination and, when this fails, contrasting effects usually may be obtained by using polarized light. There is no longer any doubt that these synthetic banded structures obtained in the ordinary course of working and annealing are due to twinning of the spinel type which was observed long ago in a number of metals crystallizing in the isometric system.' It has been customary in metallurgical literature to designate these synthetic twins, which grow into prominence during an annealing process, as "annealing twins" without regard to the actual mode of their formation, which is, indeed, obscure and with scant recognition of the fact that prior deformation is essential, no twins having been observed in metal of known unstrained history. This is questionable; especially in view of the fact that in a number of metals and minerals, reorientation into the twin configuration is known to occur as a result of a simple shearing mechanism along the recognized twinning planes and the

Jan 1, 1930

By Daniel R. Hull, H. F. Silliman, Earl W. Palmer

The brass-rolling industry has not had a great deal of experience with antimony in its product. There have been some recent excursions with antimony as a corrosion inhibitor in tubes, but in sheet brass it has been regarded with apprehension and generally avoided. This is not to say that contaminations have never occurred, and probably a great many brass mill men have had their own ideas on the effect of such contamination. Our own views were based upon certain experiences some years ago with strip castings that split lengthwise in the early stages of rolling. The nature of this splitting is shown in Fig. I, from a photograph taken in 1922 as a record of 20 bars of 65-35 common brass made with an antimonial brand of copper. These bars were cast 6¾ in. wide by I in. thick by 45 in. long. In the first pass through the rolls, 19 of the 20 split lengthwise throughout their length, while each half curved outward in a wide arc as it emerged from the rolls. In those days, if splitting was not a frequent occurrence, it was not unfamiliar. One can recall periods of short duration when large amounts of common brass would behave in this way. There was nothing imaginary about these spells. The affected metal would split lengthwise in the breakdown rolls, and no maneuvering of mill practice made any difference. The condition would descend like a plague, demoralize the mill for several days, and disappear. It is doubtful if anyone knew the cause—however many explanations may have been current. In 1921 a quantity of split brass was traced to the use of fired small-arms

Jan 1, 1943

By H. F. Silliman, Daniel R. Hull, Earl W. Palmer

The brass-rolling industry has not had a great deal of experience with antimony in its product. There have been some recent excursions with antimony as a corrosion inhibitor in tubes, but in sheet brass it has been regarded with apprehension and generally avoided. This is not to say that contaminations have never occurred, and probably a great many brass mill men have had their own ideas on the effect of such contamination. Our own views were based upon certain experiences some years ago with strip castings that split lengthwise in the early stages of rolling. The nature of this splitting is shown in Fig. I, from a photograph taken in 1922 as a record of 20 bars of 65-35 common brass made with an antimonial brand of copper. These bars were cast 6¾ in. wide by I in. thick by 45 in. long. In the first pass through the rolls, 19 of the 20 split lengthwise throughout their length, while each half curved outward in a wide arc as it emerged from the rolls. In those days, if splitting was not a frequent occurrence, it was not unfamiliar. One can recall periods of short duration when large amounts of common brass would behave in this way. There was nothing imaginary about these spells. The affected metal would split lengthwise in the breakdown rolls, and no maneuvering of mill practice made any difference. The condition would descend like a plague, demoralize the mill for several days, and disappear. It is doubtful if anyone knew the cause—however many explanations may have been current. In 1921 a quantity of split brass was traced to the use of fired small-arms

Jan 1, 1943

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By G. P. de Forest, G. O. Hiers

The object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line; (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the results of Miller,' by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-curve experiments and microscopic examination reported here. Solution of Copper in Molten Tin To determine the amount of copper that would be dissolved by molten tin at a given constant temperature the apparatus shown in Fig. 1 was used. It consists of a cast-iron pot a, 6 in. deep and 8 in. dia., well cleaned inside and dressed with graphite. This pot, which holds 15 lb. of tin, g, rests on a hot plate b with resistance winding c. The thermocouple d leads to a Wilson-Maeulen temperature regulator for maintaining the temperahre at the heating coils at a fixed temperature to within ±5°C. There is a shallow bath of solder e on the top of the hot plate to improve the thermal contact between the plate and the pot. An insulating jacket f of asbestos prevents the irregular radiation of heat from the apparatus. The copper stirrer h slowly rotates in, and is dissolved by the bath of molten tin g. This bath is protected from excessive oxidation by a layer of charcoal j. The stirrer h is fixed to the lower end of the iron tube k, which is so mounted that it can be driven by a motor with reducing gear. The temperature of the bath is indicated

Jan 1, 1930

By Cyril Stanley Smith

BeTa brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, hut at low temperature< an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shock1ey.l All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching&apos; With most ordered alloys, cold-working induces disorder and

Jan 1, 1943

By Cyril Stanley Smith

BeTa brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, hut at low temperature< an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shock1ey.l All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching&apos; With most ordered alloys, cold-working induces disorder and

Jan 1, 1943

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6&apos;7 grain boundaries and possibly twinning planes.8&apos;9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5&apos;6&apos;9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6&apos;7 grain boundaries and possibly twinning planes.8&apos;9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5&apos;6&apos;9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By Charles S. Barrett, Robert F. Mehl

It is generally understood by workers in the field of the crystal structure of metallic alloys that terminal solid solutions are of two types, the substitutional and the interstitial. In reviewing the literature, the work of Weissl on the crystal structure of the alpha copper-tin alloys was encountered, in which a new type of terminal solid solution was proposed. In brief, Weiss&apos; findings showed that the density of the alloys calculated from the side of the unit face-centered cube on the assumption of simple substitution—that is, with four atoms to the unit face-centered cell—was much higher than the density measured directly. It was suggested that the assumption of four atoms to the unit cube is not valid for these alloys, and that each unit cube contained less than four atoms; in other words, that one tin atom replaces more than one copper atom, leaving some atomic positions unoccupied. Such a structure, if verified, would have far-reaching significance in the study of the crystal structure of metallic alloys. It would indicate a complexity in terminal solid solutions not hitherto suspected and might encourage work leading to the discovery of other alloys of the same type, and perhaps to types intermediate between it and the two recognized types. It is of importance, therefore, to reinvestigate these alloys with respect to the type of solid-solution structure obtaining therein. Materials and Experimental Method The alloys were prepared from electrolytic copper cut directly from the cathode and the high-purity tin furnished by the U. S. Bureau of Standards for the calibration of thermocouples. No analyses for impurities of these materials or of the finished alloys were made, since such impurities as might be present could have only a wholly inappreciable effect upon the data obtained and the conclusions drawn. The alloys were made by melting the weighed copper charge in a graphite crucible under a KCl-LiC1 flux with later additions of NaC1, using induction heating. When the copper was melted the weighed portions of tin were

Jan 1, 1930

By Cyril Stanley Smith

Although not of the same importance as electrical conductivity, the capacity for conducting heat is nevertheless a very important property of metals and alloys. A knowledge of thermal conductivity is of value in selecting alloys for many purposes and in the calculation of the efficiency of apparatus which is being designed. Unfortunately, the determination of thermal conductivity is extremely slow and tedious, consequently few data have been obtained. A further reason for the lack of information is that there has long been an impression that the thermal conductivity of an alloy is directly proportional to the electrical cónductivity and that it can therefore be calculated from the latter. The Wiedmann-Franz-Lorenz law of constant ratio of the two conductivities holds with a considerable degree of precision for all the pure metals, but appreciable deviations occur in certain alloys—particularly those containing nickel—and it seems difficult to predict exactly what the ratio will be. Therefore direct determinations of thermal conductivity should be made whenever the results are needed with any accuracy. This research is intended eventually to cover all the alloys of copper that are of commercial importance, including the binary alloys of copper with zinc, tin, aluminum, nickel, silicon, manganese, cadmium and phosphorus, and the ternary alloys copper-nickel-zinc, copper-nickel-silicon, copper-manganese-silicon, copper-zinc-tin, etc. Most of these alloys are customarily used in the wrought condition and therefore were tested in the form of annealed rods. A limited number of sand castings were also obtained and examined. This paper contains a complete review of all the previous work that has been done on copper alloys, and includes a detailed description of the apparatus and method of procedure used in the present research, together with the new results obtained on the copper-zinc series, which is the only one completed at the present time. Subsequent papers describing the other alloys will contain the experimental results and discussion only. Previous Work Copper The conductivity of copper has been studied by many observers since the pioneer work of Wiedemann in 1859. The majority of these measure-

Jan 1, 1930

By L. L. Wyman

Previous studies1 by the writer dealing with the embrittlement of copper have been concerned with the behavior of various pure and deoxidized coppers when exposed to an oxidation-reduction cycle, and the consequent evaluation of these materials on the basis of their resistance to this action. No attention was devoted to the variations in penetration of embrittlement with time, when these copper materials are exposed to a strong reducing gas, such as hydrogen, nor to the variations in oxygen penetration, with time and temperature, into the "pure" coppers. The cause of the embrittlement is the reduction of the oxygen in the copper by the hot reducing gas, so that a consideration of time, temperature, the occurrence of hydrogen and oxygen must be given. For the purpose of differentiating some of the involved factors, the present work may be divided into two separate series of experiments. The first of these deals with the oxidation of purified coppers under various conditions and then the subjection of these to a standard hydrogen treatment. The second series concerns the reduction, under different conditions, of tough-pitch coppers of several oxygen contents. The resulting data will give the rates of oxidation, and of reduction, for the materials involved. The first series of experiments will reveal how rapidly copper may become oxidized, while the second series will indicate how rapidly embrittlement will penetrate into an oxygen-containing copper when it is exposed to hydrogen at different temperatures. Materials For the purpose of determining these variables, three types of material were selected, to cover the extremes in the ranges of materials commercially obtainable. The first class of materials is represented by an oxygen-free copper, as well as the high-purity vacuum-melted copper2 used in previous work. These materials were selected to determine the variation of oxidation with time and temperature, by oxidizing these coppers under various combinations of these factors, and noting the effect as indicated by a

Jan 1, 1934

By L. L. Wyman

The resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.&apos; Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-phered furnaces such as customarily are used for this operation. As might be expected, several other factors exist—such as oil, dirt on the wire, or in the furnace, or metallic surface contacts—that might produce reducing gases and be the source of the trouble. However, in consideration of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that3 the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder&apos;s observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the resultant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments comparable to those previously conducted by the writer,&apos; which would clarify the effect of the steam on copper, and in copper in the presence of steel. Material The material used in these experiments was tough-pitch copper wire of rectangular cross section, about % in. thick, picked at random from the regular factory production of material used for windings, etc., in the electrical industry. Chemical analysis of this material gave the follow-

Jan 1, 1940