Search Documents

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By Herman Halupka

El presente texto describe los progresos alcanzados durante los cinco años de operación de dos hornos en la fabricación de pelets que desarrolló la mina Marcona a través del sistema de parrilla deslizante, patente Dravo-Lurg. Asimismo, se señala os procesos empleados para fabricar pelets como: molienda y concentración, filtración, bolas verdes, endurecimiento, y la preparación del concentrado de mineral de hierro para ser peletizado.

Jul 1, 1969

By Pedro E. Sarquís

Durante varios años se ha utilizado los extractos de quebracho como depresores y dispersantes en los procesos mineros. Empero, existe una nueva forma familia de extractos de quebracho modificados que pueden ser aplicados en los procesos de flotación. Estos reactivos orgánicos naturales, extraídos del quebracho, se aplican en bajos consumos y por tratarse de productos de origen natural, se presentan como una alternativa limpia en relación a los reactivos tradicionales. En ese sentido, el presente trabajo señala la utilización de diferentes extractos de quebracho modificados, dispersantes y depresores, en los ensayos de flotación de sulfuros y también en minerales no metalíferos, donde su aplicación no solo permite mejorar la selectividad, sino mejorar la recuperación de los minerales valiosos.

Sep 12, 2005

By Joseline Pérez, Geraldine Pinedo, Sara Blaz

La exploración minera y los descubrimientos son el futuro de la continuidad de Perú como país minero. Conscientes de la importancia de esta actividad, el presente ensayo se enfoca en identificar problemas críticos que, en la actualidad, afectan a los proyectos de exploración minera, principalmente a nivel de cronograma, y que restan competitividad a nuestro país. Este trabajo visibiliza cómo los titulares mineros pueden llegar a tener cronogramas de hasta de 2 a más años para poder iniciar exploración y la importancia de atender a este problema a través de soluciones regulatorias y de gestión en los distintos niveles y de forma transversal con otros sectores.

Sep 29, 2023

By Y. Bai, J. J. Liu, D. Q. Li, S. Z. Liu, X. T. Wang

"This paper presents the results of an industrial test using 8 t/d of Baotou concentrate (50% REO) of a clean metallurgical process, which includes: 1. Roasting with H2SO4 at low temperature (220~260 0C) in a batch roasting furnace followed by water leaching to obtain a leach liquor as feed with a yield of >95% RE and Th, recovering F as fluoride, producing a leach residue amounting to 1/3 of an equivalent high temperature residue and containing <0.03% Th and radioactivity < 3×104 Bq/kg compared to the normal high temperature residue containing 0.2-0.3% Th and 1×105 Bq/kg. 2. Separating Th with N1923 and extracting RE by P507 has been completed in mixer-settlers. Test results indicate that the ThO2 product has a purity of > 95% with a yield of 99%, and the RE has a yield of >95%, in which ThO2/REO <5×10-6, and that P507 loaded RE connect straight with separating RE using P507-HCl system. 3. Treatment and multipurpose use of "three wastes" (water, gas and solids) are discussed in some detail."

Jan 1, 2014

By Alejandro Euribe Dulanto

El presente estudio describe el uso de la palinología y su aplicación a la geología económica. Asimismo, revisa la morfología y la clasificación de las esporas y polen, como la distribución de este por corrientes y la relación de la "lluvia de polen" con la vegetación actual. Se describen también las técnicas palinológicas en la preparación de muestras, los datos sobre la preservación del polen y esporas en los sedimentos, los efectos del intemperismo y la acción que sufren los granos de polen y esporas cuando se les encuentra a grandes profundidades. De otro lado, se narra el establecimiento de zonas palinológicas como los conocimientos sobre los cambios florales, determinando que la evolución es el factor principal que se emplea para las zonaciones palinológicas, aunque las condiciones climáticas y los efectos de sedimentación no generan variaciones en la flora, siendo de importancia en trabajos de correlación local. Finalmente, a través de un ejemplo, se explica la importancia estratigráfica de los estudios palinológicos en el Perú.

Jul 20, 1961

By Márcio de Morais Tavares

A espectrometria de fluorescência de raios X (FRX ou XRF) é uma das técnicas analíticas mais utilizadas em geoquímica. Na indústria mineral também se utiliza a espectrometria de absorção atômica (AA). A comparação de concentrações de sílica e alumina de oito amostras padronizadas de minério de ferro obtidas a partir das técnicas FRX e absorção atômica, constitui o objetivo deste trabalho. Foram realizadas análises dos mesmos padrões em outros dois laboratórios para reprodutibilidade dos resultados. Foram utilizados um espectrômetro FRX e um espectrômetro de absorção atômica para realização dos ensaios. As análises produziram resultados satisfatórios, com desvios médios de 0,502 para a sílica e 0,096 para a alumina.

Aug 16, 2017

By Deusdedit Motta, Marcos de Oliveira Fonseca, Marlon Rosa de Gouvea

A Transformação Digital é a palavra de ordem em todo o mercado mundial e na indústria não é diferente, principalmente no que se refere à Gestão de Ativos de produção. Dentre as diversas técnicas de Analítica Preditiva disponíveis, algumas se destacam pela sua capacidade de facilmente aprenderem o comportamento dos ativos a partir dos dados históricos, assim como monitorarem pequenos desvios que estejam relacionados aos mecanismos de falhas de interesse. O presente trabalho apresenta como estender uma das técnicas de Inteligência Artificial para Modelamento Baseado em Similaridade para aplicação em ativos que possuem uma dinâmica rápida de funcionamento ou de operação para seus estados estacionários. São demonstrados os resultados dessa abordagem em aplicações práticas que exemplificam como aumentar o resultado proporcionado por essa técnica na obtenção de ganhos para o desempenho dos ativos e resultados do negócio.

Oct 1, 2019

By Hamid Maleki

Prudent design of coal pillars in any mining system requires an estimation of in-situ pillar strength, overburden lateral load transfer capability, and a failure criterion. Pillar strength is typically determined using one of several different empirical pillar strength formulas. For coal reserves in the U.S., a new pillar design method was proposed based on extensive U.S. field measurements in underground mines (7) which accounted for confinement effects. Field measurements in seven U.S. seams indicated highest strength for some Utah mines where the coal seam developed high confining stresses. Lower strength was measured in structurally controlled seams. This method is expanded here including the data from the weaker tertiary coal measure rocks and lower confinement for pillars with low width-to-height ratios. The determination of how much load a pillar is expected to take is partially dependent on the ability of overburden to transfer load laterally; this is useful for selection of panel width and barrier pillars size in select mining applications where long-term stability is required in conservative designs. In caving mining systems, caving of the strata is influenced by geologic, mining and stress conditions and the released energies influences how the pillars react at loads approaching pillar strengths. Overburden deformation and caving mechanisms are analyzed in this paper in multi-panel extractions to enhance the understanding of load transfer, seismicity and coal bump control in deep western U.S. operations.

Jan 1, 2008

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

In this study, the dissolution behavior of copper and arsenic from five different copper concentrates containing 21-34.7 %wt. of Cu, 1.3-7.3 %wt. of As and 15.6-27.5 %wt. of Fe were investigated under high pressure oxidative leaching conditions. Leaching experiments were conducted using different leaching reagents such as ferric sulfate, sodium chloride, deionized water, sulfuric acid and ferric sulfate-sodium chloride mixture in order to compare the effectiveness of each on the dissolution of copper and arsenic from copper concentrates. The effects of ferric sulfate (0.1-1 mol/L), sodium chloride (0.1-0.5 mol/L) and leaching temperature (100-180C) were investigated under 1 MPa autoclave pressure , particle size >45 m, pulp density of 100 g/L, stirring speed of 750 rpm and leaching time of 60 min. Results showed that the most effective leaching reagents for the dissolution of copper are 0.34 M NaCl and a mixture of 0.1 M Fe2(SO4)3 - 0.34 M NaCl, in which As extraction did not exceed 7%. The copper concentration in the pregnant leach solution obtained after leaching using 0.1 M Fe2(SO4)3 - 0.34 M NaCl was 13-30 g/L, while the concentration of As and Fe were in a range between 0.3-1 g/L and 0.2-10 g/L at 160C. INTRODUCTION Copper sulfide minerals, such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and covellite (CuS) are used for the production of copper in mining and metallurgical industries worldwide. The conventional pyrometallurgical processing followed by electrorefining is a common process for the production of high purity copper (Moskalyk, & Alfantazi, 2003; Padilla, Aracena, & Ruiz, 2012). However, the degradation of copper content and an increase in the amount of metal impurities, especially arsenic (As), antimony (Sb) and bismuth (Bi) in copper concentrates cause serious problems to the production of copper and environmental pollution (Basha, Selvi, Ramasamy, & Chellammal, 2008; Long, Peng, & Bradshaw, 2012). Hydrometallurgical processes are used to recover metals from refractory ores, concentrates and tailings by leaching (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018). During the last decades, hydrometallurgical processing for the recovery of copper from enargite-bearing copper ores and concentrates has been extensively investigated due to its relatively more environmentally benign and less capital costs than the conventional pyrometallurgical processes (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018; Choubey, Lee, Kim, & Kim 2018). However, several issues facing the hydrometallurgical processing are incomplete extraction of copper associated with the coprecipitation of iron compounds, difficult stabilization of toxic impurities and production of a contaminated copper product (Dreisinger, 2003; Safarzadeh, Moats, & Miller, 2014). Hence, a number of studies have been conducted on the selective dissolution of copper from copper ores and concentrates or selective removal of arsenic leaving a clean copper residue using various leaching reagents or lixiviants (Safarzadeh, Moats, & Miller, 2014; Mihajlovic, Strbac, Zivkovic, Kovacevic, & Stehernic, 2007; Tongamp, Takasaki, & Shibayama, 2009). More extensive studies on the selective extraction of copper from enargite- bearing copper ores and concentrates are much needed to improve copper recovery.

Jan 1, 2019

By E. D. Gardner

This paper discusses small-scale lade gold mining and milling. It is abstracted from a bulletin being prepared by the United States Bureau of Mines entitled "Equipping, Developing, and Operating Small Gold Mines." Gold is widely distributed in the mountainous regions of the United States; relatively few deposits, however, can be profitably worked on a large scale. Because of the high intrinsic value of gold, ores containing this metal may be very rich; hence it is possible to mine profitably smaller bodies of gold ore than of the more common metals.

Jan 1, 1934

By Elmer Peña Matta

Un estudio anterior sobre la mena Pb. Zn en la concentradora de Paragsha determinó que los finos encontrados en la alimentación de los molinos, se podía separar, evitando la remolienda y la alimentación directa del ciclón, para luego obtener los productos destinados a la flotación y molienda, respectivamente. En este sentido, el objetivo del texto, radica en mostrar los resultados del uso de los cedazos DSM en los molinos primarios, asi como el proceso de la adaptación del mismo. El acondicionamiento de los cedazos DSM es un proceso que permite recibir alimentación de una faja transportadora y descargar su cajón de alimentación original, que está diseñado para la descarga de la bomba. De forma que la aplicación de los cedazos DSM es factible en menas que no necesitan molienda, donde se aumenta la capacidad en el equipo de la molienda, se mejora la clasificación de los productos, y surgen nuevas perspectivas de incrementar la metalurgia, especialmente en especies friables. Asimismo la ubicación de un cedazo DSM varía de acuerdo a la necesidad, sea la entrada de molinos, ciclones, descargas de molinos de varillas, bombas con productos por clasificar, equipos de heavy medium, etc.

Jul 20, 1960

By Jaime Tumialán

El presente artículo describe los trabajos subterráneos de la mina Cobriza, la mina más mecanizada del Perú, dado que es la primera en aplicar el minado sin rieles con equipo pesado montado sobre llantas neumáticas u orugas. La mina se encuentra localizada en la Oroya, Huancavelica. Las razones de su mecanización son: crecimiento de los costos, avance de la tecnología, la forma, magnitud y potencia del manto, así como la dureza y resistencia del mineral. Su método de minado es "Corte y Relleno altamente mecanizado con equipo pesado y tiene una productividad en subsuelo de 20Tn/h-g.

Nov 1, 1972

By José Gonzales

"Una rampa es uno de los aspectos más importantes de la planificación a cielo abierto- en tanto se define como un camino con cierta pendiente que se desarrolla desde la parte superior del tajo hasta la parte más profunda del mismo. En ese sentido, el presente texto señala la ecuación que describa una rampa en 3D de un tajo abierto, a través de los parámetros constantes de diseño el desarrollo de la rampa. Entre los parámetros considerados tenemos: ancho de la rampa, pendiente de la rampa, ángulo interrampa del tajo, radio de la base superior del tajo (máxima área superior que engloba toda la fase), radio de la base inferior del tajo (mínima área de trabajo para los equipos). Una vez desarrollado el diseño de la rampa en función de los cinco parámetros anteriormente descritos, se podrá determinar mediante la codificación de un software denominados UNI-RAMP, el número de vueltas que requerirá la rampa para llegar al fondo del tajo, la profundidad total del tajo y el ángulo global del tajo. "

Dec 1, 2015

By Ruxton B. P, Rhodes J. M

Two Rb-Sr ages are discernible in data concerning the leucocratic granite which is the youngest pre-sedimentation phase of the crystalline basement complex at Rum Jungle, Northern Territory, Australia. Whole-rockdata suggest that intrusion of this unit took place at about 2400 my ago, with a probable initial ratio around o&#183;707; whole rock-potassium feldspar tie-lines indicate redistribution of strontium at about 1800 my ago. The former age correlates with other measurements on rocks which form basement to the mantling Pine Creek Geosyncline; the latter correlates also with isotopic evidence for regional metamorphism and emplacement of some younger intrusive granites elsewhere within the geosyncline. A few K-Ar ages, from scattered localities, conform generally with the later event or events which appear to have some connection with the structural deformation clearly observable both in the complex and the surrounding metasediments. It is these younger events which appear to match the residual evidence for the earliest detectable concentration of uranium minerals in the Alligator Rivers district.

Jan 1, 1977

Experiments on High Efficiency Separation of Mixed Plastic Wastes by Vortex-Tube Separator

Sep 13, 2010

By Parry. V. F.

"INTRODUCTION Coal is a compressed mass of heterogeneous, macerated, metamorphosed plant remains that have collected in the earth's crust. Probably no two beds of coal have identical properties, and different parts of the same bed may vary considerably when measured by some of the many empirical tests that have been developed to classify or differentiate the properties of coal. Because of this great variability in properties, the commercial processing of coal to produce coke and byproducts has developed largely as an art based on experience, rather than as a science. Much empirical chemical research, however, has been and is being conducted on coal carbonization, and this work is of practical value in obtaining larger yields of gas and byproducts and in the improvement of the physical properties of the coke.Both ultimate and proximate analyses have been used for correlating purposes. 3/ In the United States the proximate analysis is used for the classification of coal according to rank and grade. The proximate analysis can be employed usefully in the coal—carbonization industry because separation of the combustible matter of coal into volatile matter and fixed carbon is, in fact, a small carbonization test conducted on 1 gram of coal heated in a platinum crucible.Small—Scale Laboratory Coking Tests,Many empirical tests have been devised for determining the coking properties and measuring the yield and quality of gas and byproducts obtainable from various coals. These tests, made on samples ranging from 25 grams (about 1 ounce) to 5 kilograms (11 pounds), furnish information that is roughly proportional in practical value to the size of the sample carbonized. However, the cost of the carbonization test also increases with the amount of the sample, so that for preliminary surveys of a number of coals, samples of 25 to 1,000 grams usually are employed."

Dec 1, 1939

By Richard Manrique

"La implementación del proyecto de modernización de la fundición de cobre de Southern Peru Copper Corporation requiere cambiar la metodología de funcionamiento de los sopladores para la etapa de conversión. En este sentido, el presente texto señala los aspectos del Sistema de control maestro de reparto de carga implementado en la Fundición de Ilo con excelentes resultados, logrando mejorar el rendimiento de los equipos con una antigüedad de mas de 30 años e invirtiendo tan solo en nuevos controladores en una etapa ligada directamente a la línea de producción. Mantener la variable primaria presión en la red de sopladores, compartiendoóptimamente la carga entre los sopladores en la red, mientras que, se minimiza el riesgo de surge, consumo de energía y los disturbios en el arranque y el paro de sopladores individuales, el sistema deberá ser lo suficientemente flexible que no deberá de perturbarse ante la salida frecuente de los convertidores, es decir deberá de mantener las presiones y flujos a la descarga del manifold ante las variaciones en el consumo de aire todo esto con un mínimo de venteos al ambiente."

Sep 19, 2006

When the mining and milling of 1100 copper orebody commenced at Mount Isa a satisfactory grade of copper concentrate was difficult to produce. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in inherently flotable fine pyrite and siliceous particles.The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1971

By Werner Ruegg

El presente texto describe algunos aspectos y propiedades de índole mineralógico, genético e individual de los diferentes yacimientos fosfatados. Existe una diversidad de fosfatos combinados como calcio, fluor, hierro, etc pero están aquellos también que son usados para fertilizantes limitados a los fosfatos cálcicos. De éstos, la apatita es su forma cristalina primaria, constituyéndose como la fuente de combinaciones. La fosforita, a su vez, es su contraparte amorfa, que establece un precipitado químico o un residuo orgánico donde existen combinaciones entre los dos.

Mar 1, 1984