Search Documents

This publication summarizes the in-house and contract research and development projects programed for fiscal pear 1980 by the Bureau of Mines under its Minerals Environmental Research activity. The document provides a mechanism for interested parties, including potential contractors, to gain insight into ongoing and projected work of the Bureau's environmental research efforts. Research to identify and correct environmental problems associated with mining and metallurgical operations has long been an integral part of the Bureau's mission. Through the years, efforts of various Bureau programs have yielded valuable information on the origin and control of many of these problems. With the reorganization of the Bureau of Mines in 1979, the Minerals Environmental Technology program was structured to consolidate these efforts into a single program that will systematically investigate al aspects of mining- and processing-related environmental pollution and damage-from initial discovery of the mineral resource to ultimate return of the land to productive use. In fiscal year 1980, the Bureau received an appropriation of about $21 million to conduct research and development work on these problems.

Jan 1, 1980

By J. I. Paige

The Bureau of Mines studied methods for recovering unreacted titanium minerals and petroleum coke from titanium chlorination plant wastes prior to neutralization treatment with lime. The objective was to recover valuable raw materials and to reduce the amount of waste materials that must be treated for disposal. Samples of solid wastes were physically beneficiated by gravity concentration (tabling) to recover titanium minerals containing 69.0 to 92.4 wt-pct Ti02 and by selective carbon flotation to recover petroleum coke containing 94.0 to 96.8 wt-pct C. Laboratory data indicate that the recovered titanium mineral would decrease the amount of solid waste to be disposed of from 32.8 to 53.9 wt-pct. The recovery of coke would further decrease the amount by additional 32.9 wt-pct. Preliminary tests conducted on recovering vanadium, chromium, and columbium from liquors obtained by leaching chlorination residues also have shown that (1) 97 pct of the vanadium was extracted from leach liquors in a two-stage solvent ex-traction procedure and (2) 58 pct of the columbium and 40 pct of the chromium were separated from the leach liquors by an ion exchange technique using a strong acid resin.

Jan 1, 1982

By George A. Costello

A theoretical analysis is presented for the static and dynamic response of wire rope in deep-shaft mining operations. Expressions for the stresses in the individual wires of complex wire ropes are derived, and specific results for simple strands, 7x7 ropes, 6x 19 Seale ropes both with and without internal-wire-rope cores, and 6x25 filler-wire ropes both with and without internal-wire-rope cores, are presented for the case of ropes subjected to a combination of axial loading and bending over a sheave. Consideration is also given to the dynamic overloading associated with certain mining operations, such as dumping ore into a suspended skip and accelerating a fully loaded skip upward. Experiments to determine the axial stiffness of wire rope are described. Factors affecting the service life of wire rope, such as residual stresses, contact stresses, and fatigue behavior, are discussed. Specific research areas in need of further investigation are identified.

Jan 1, 1983

In Bureau of Mines research on recycling chrome refractory wastes, used refractories from argon-oxygen decarburization and electric steelmaking furnaces were beneficiated, concentrates were reformed into briquets, and modulus of rupture tests were conducted at 1,350° C. The test results indicated that the beneficiated minus 6-mesh material could be used for producing magnesia-chrome refractories.

Jan 1, 1980

Longwall minim; is a highly mechanized, high productivity mining method that is finding increasing applications in coal. Although the method would be highly advantageous in certain hard rock mining applications it cannot be applied in hard rock because no suitable cutterhead exists for such materials. The wedge longwall cutterhead is a, roller cutter device that is wedge-shaped, with cutters arranged to eliminate the very large normal force ordinarily required to cause such cutters to penetrate hard rock. However, the wedge geometry cannot be extended to a point: special nose cutters are needed to open a narrow slot for the wedge. This report describes the design, fabrication, and successful field testing of these critical nose cutters.

Jan 1, 1974

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By S. Harteis, D. Dolinar

Many mining operations rely on bulkheads to provide a barrier between impounded water or slurry and active mine workings. However, bulkhead failures could cause and have caused catastrophic flooding that puts the underground workforce at risk. The National Institute for Occupational Safety and Health1 (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) is conducting research to evaluate the adequacy of existing design practices for water and slurry bulkheads. A key component of this research effort is documentation of the performance history and design parameters for bulkheads installed in underground coal mines during the last 20+ years. This research is part of a larger effort to develop general design guidelines and procedures for constructing and maintaining bulkheads that will help to ensure their long-term structural integrity, while significantly reducing the inundation risk for miners. This paper presents the results of NIOSH’s research to identify state-of-the-art bulkhead designs, including design criteria, leakage monitoring systems, and emergency warning systems. Underground observations and evaluations of existing bulkheads suggest that the most important design factors influencing their performance are the interface of the bulkhead with the surrounding strata and the potential magnitude of the hydraulic pressure to which they may be subjected. When a bulkhead has failed, leakage has generally been through the surrounding strata or along the bulkhead/strata interface, with the failure potential along the interface increasing with hydraulic head. It was also determined that development of a monitoring program to ensure the long term structural integrity of bulkheads is an important safety consideration. Current monitoring procedures range from weekly visual inspections to constant monitoring via pressure transducers and fluid level indicators. Where possible, these devices are used in conjunction with a computer based mine monitoring system to alert mine personnel when an emergency condition exists at the bulkhead installation.

By Kenneth G. Skinner

The rapid growth of the metallurgical, chemical, and allied industries on the Pacific coast just prior to and during the war caused a sudden increase in the demand for refractories, which was the immediate cause of a revival in interest in refractory clays available on the Pacific coast, particularly in the Pacific Northwest. Population increases and shortage of shipping facilities caused an increase in the amount of various ceramic materials and products used and produced on the Pacific coast, with accompanying demand for information regarding sources of clay. In an effort to supply part of this information, the Bureau of Mines, in cooperation with the College of Mines, University of Washington, started a program in 1944 to test the refractory and other properties of clays from seven Pacific Northwest deposits that had been drilled and sampled as part of the Bureau of Mines alumina from clay investigation. Figure 1 shows the location of these deposits.

Jan 1, 1949

By J. J. S. Sebastian

The process development described in this report was carried out at the Morgantown Station of the U. S. Bureau of Mines in cooperation with West Virginia University. An experimental laboratory-scale pilot unit to gasify coal dust in entrainment was constructed on the Campus of the University in Morgantown. The enormously accelerated demand for liquid and gaseous fuels and utilization of our immense coal resources require that a low-cost process be developed for the gasification of a wide variety of coals. Such a process would be a major factor in lowering the cost of synthetic liquid fuels. None of the proc3sses developed in Germany prior to and during World War II, such as the Winkler process, the H. Koppers dust gasification process, the Wintershall-Schmalfoldt process, etc., meet all the requirements for a low-cost process under American conditions. Nor has any other process designed and experimentally operated at atmospheric pressure during the post-war period in this country appeared to fulfill all of the necessary conditions for a low-cost process.

Jan 1, 1950

By R. K. Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed which allow the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By T. H. Jeffers

The Bureau of Mines conducted a laboratory investigation of copper electrowinning from electrolytes produced by solvent extraction. The purpose of the research was to gain a better understanding of the fundamental relationship between copper electrowinning conditions, anode corrosion, and cathode purity. Processing variables were evaluated in a cyclic semicontinuous system in which the depleted electrolyte was used to strip copper from loaded organic extractant. For the production of high quality copper cathodes, the electrolyte was dosed with cobalt and stripped of organic solvent extraction reagent. An optimum cobalt addition of 60 ppm, and removal of the entrained extractant with activated carbon provided the best conditions for electrowinning copper containing the least amount of lead and controlling anode corrosion. As little as 13 ppm of the entrained organic extractant, LIX 64-N, significantly accelerated anode corro-sion. However, the addition of 1,000 ppm of organic diluent kerosine did not affect anode corrosion. After cobalt dosing and removing the entrained extractant, cathodes containing less than 2 ppm lead were consistently electrowon at widely varied current densities, electrolyte copper and acid concentrations, and temperatures. Dosing of the electrolyte with selected impurities including magnesium, aluminum, manganese, and iron did not affect the cathode purity. However, 0.05 giL of chloride ions markedly increased anode corrosion and the sub-sequent transfer of lead to the cathode copper.

Jan 1, 1985

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982

By W. P. Yant

Canister-type gas masks Pave become an essential part of the equipment of many industries, not only for use in .emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau bas become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By J. B. Zadra

The use of activated carbon for extracting gold and silver from pregnant cyanide solution and pulp has been investigated many times. The primary advantage of this use of activated carbon is that .the dissolved values can be recovered from slimy ore pulps or from slime portions of ore without settling and thickening or filtering. The loaded carbon is removed from the barren pulp, and the pulp can then be discarded. Activated carbon has been used recently in treating gold ores containing very little soluble silver. When the carbon was loaded with a suitable amount of gold, the silver load was negligible. The remaining problems concerned the removal of the gold from the carbon, the recovery of the gold as bullion, and the reuse of the unloaded carbon. As described in a recent report, a method that solved these problems was developed. The gold-laden carbon was leached with caustic sodium sulfide solution and the gold simultaneously recovered by electrolysis. Both the carbon and the spent solution can be reused. That process was applicable to gold-laden carbon only. It was not applicable to carbon carrying silver, because sodium sulfide does not leach silver from carbon but "fixes" it. It has been necessary, therefore, to develop a modified process for the removal or desorption of both gold and silver from loaded carbon. This modi¬fied process permits the use of activated carbon for extracting both gold and silver from gold ores carrying enough silver to have economical interest or in which silver may be the predominating value.

Jan 1, 1952

By H. R. Appell

The Bureau of Mines is experimentally converting cellulose, the chief constituent of organic solid waste, to a low-sulfur oil, All types of cellulosic wastes, including urban refuse, agricultural wastes, sewage sludge, wood, lignin, and bovine manure, have been converted to oil by reaction with carbon monoxide and water at temperatures of 350° to 400° C and pressures near 4,000 psig, and in the presence of various catalysts and solvents, Cellulose conversions of 90 percent and better (corresponding to oil yields of 40 to 50 percent) have been obtained. A continuous reactor for use at maximum conditions up to 500° C and 5,000 psig has been operated successfully, Using sucrose as a feedstock, operation in this system has permitted a simplified and preliminary chemical study of the conversion process. Oil yields of over 30 percent have been obtained with this unit.

Jan 1, 1971

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By Fredrick L. Johnson

The Bureau of Mines, under Congressional mandate, conducted a mineral survey on the Park Range WSA (Wilderness Study Area) in 1984 and 1985. The WSA, located about midway between Tonopah and Ely, encompasses 47,268 acres. No mineral resources were delineated, nor were workings found, during the investigation. There has been, however, exploration in and near the north end of the study area. ASARCO is actively exploring a block of 41 claims for hot-spring type, low-grade, large-tonnage gold deposits. Their claim block is almost entirely in the study area. The Morey mining district, 7 miles southwest of the study area, produced silver and lesser amounts of gold and lead sporadically from the mid-1860's through the mid-1960's. The WSA is underlain by Tertiary rhyolitic and latitic volcanic rocks and by Paleozoic sedimentary rocks. The Paleozoic rocks have been faulted, silicified, brecciated, and hydrothermally altered, and have anomalous concentrations of precious metals and pathfinder elements. Additional exploration in the north part of the Park Range WSA may lead to delineation of gold resources.

Jan 1, 1986

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.