Search Documents

By Keith L. Harris

Buoyed primarily by growing consumer spending, the economy rebounded from a weak second quarter. According to preliminary estimates released by the Department of Commerce, real gross national product (GNP) grew $2 1.9 billion during the third quarter, producing a seasonally adjusted annual growth rate of 2.4%, compared with a rate of 0.6% in the second quarter of 1986 and 4.1% for the third quarter of 1985 (table 1). Third-quarter real personal consumption expenditures and Government purchases of goods and services rose $42 billion and $7 billion, respectively, but those gains were partially offset by the continuing decline of gross private domestic investment, off $16 billion, and the growing trade deficit, up $11 billion. Three quarters of the growth in consumer spending occurred in the durable goods sector as consumers responded to discounted financing offered by automobile manufacturers attempting to lower inventories of 1986 vehicles, Increased purchases of other durable goods, such as furniture and home furnishings, also contributed to the strength of the durable goods sector. The success of the automobile inventory reduction program as well as weak factory output led to a $20 billion decline in inventory growth. Investment for housing and producers' durable equipment expanded, however, and mitigated some of the impact of slower inventory depending on gross private domestic investment, Capital spending for nonresidential structures declined for the third consecutive quarter. The declining capital spending and the growing trade deficit continued to be significant and interrelated problems for the economy. Real capital spending for new plants and equipment during 1986 is expected to decline 2.5% after rising 8.7% in 1985 and 15.8% in 1984 (table 2). It is likely that capital expenditures bottomed out in the second quarter and that they will expand in the third and fourth quarters. The first-half decline was partially attributed to uncertainty arising from the pending tax- overhaul bill. Furthermore, there is little impetus for corporations to invest in new capacity since factories are operating at less than 80% of capacity (table 3) largely because of the continuing growth of imports. The growth rate of the trade deficit dropped sharply in the third quarter to less than half that of the previous quarter. Low oil prices, declining auto- mobile and steel imports, and increased exports of agricultural goods contributed to this decline. The continued low growth of the economy caused the Federal Reserve System to reduce the discount rate for the fourth time this year (in late August), drop ping it to 5,596, the lowest level in about 9 years. Inflation, as measured by the fixed- weighted GNP price Index, continues to remain low, but rose from the revised second-quarter level of 1.7% to 2.596, mostly because of rising food costs.

Jan 1, 1986

By BUREAU OF MINES

In July, 1918, the attention of the Secretary of the Interior WItS called to the rapidly increasing cost of producing gold and the declining output of that metal in the United States. Realizing the importance of the gold-mining industry, the Secretary appointed a. committee, consisting of Hennen .Iennings, chairman, J. H. Mackenzie, and Charles Janin, of the Bureau of Mines, and H. D. Me- Caskey and F. L. Ransome, of the United States Geological Survey, to,make a thorough study of the gold-mining situation in the United States. The study was to cover the increased cost of recovery and the decreased output of gold, and to consider the different measures that had been proposed to relieve the industry and stimulate production. This report embodies the results of the investigation and study made by the committee. The report presents statistical data compiled from various sources, showing the production of gold in the United States and other countries, with comparative figures for coal, iron, and other mineral products, and describes the sources and distribution of gold output in the United States. It discusses the relation of gold' production to finance and credit, the causes for the decline in gold output, and measures for the relief of the industry. The Interior Department publishes this report in the belief that the widest publicity possible should be given the findings of the committee in order that attention may be directed to the serious conditions revealed therein, and in the hope that wide discussion of the subject may result in some action being taken that will aid in upholding the gold standard ,and the gold industry.

Oct 30, 1919

By O. C. Garst

"The lightness and relatively high strength per unit weight of certain magnesium alloys have interested designing engineers for many years. Ever since the noted investigator Bunsen3/ first produced the element by electrolysis of the fused chloride in 1852, utilization of this light metal has been considered. Magnesium is widely distributed over the earth's surface in high-grade as well as low-grade deposits; it occupies eighth place in the list of elements arranged in order of their decreasing abundance, as there is 2.24 percent magnesium in the earth's lithosphere. Even though the element is distributed widely in the form of relatively insoluble: minerals and also as soluble salts in sea water and spring water, as well as being an indispensable constituent of plants and animals, the technology of magnesium was slow development. This slowness of development was first caused by confusion or the part of the early investigators who thought that magnesia, magnesite, magnetite, and the pyrolusite-type manganese ores were compounds of the same metal. At one time the metal that we now know as manganese was called magnesium, and magnesium was called either magnium or talcium. In addition to this coon, the chemical activity of the metal, especially at high temperatures, created problems that are still difficult to solve.With the advance of science in all branches, .methods for -he production of magnesium were developed. The methods first used for producing the element were: (1) reduction of magnesium salts with alkali metals,4/ (2) electrolysis of aqueous solutions of magnesium salts, and (3) electrolysis of fused magnesiun salts.The first attempts to produce magnesium by the carbothermal reduction of magnesia were failures as sufficient thermodynamic knowledge concerning the reversibility of the reaction between magnesia and carbon was not at hand. As the igneous electrolytic Method for making the element was more easily controlled than the others and. yielded more metal per unit of energy, considerable work was expended on the improvement of this process. The work in this field paralled that on the electroreduction of aluminum and the alkali metals. For several years the entire magnesium industry was dependent on this igneous electrolysis process for its supply of the metal, but as demand for the metal increased and more scientific knowledge was available, other processes were developed. Today magnesium is produced by the electrolysis of molton magnesium chloride electrolytes, the carbothermal reduction of magnesia, in arc furnaces followed by shock cooling of the furnace gases by a coin inert atmosphere, and the silicothermal reduction of calcined dolomite in stainless steel retorts."

Mar 1, 1946

By Ernest A. Hersam

"INTRODUCTION.Luring the year 1923 a complete survey was made of the condition of research in the reduction (milling) and concentration of ores and nonmetallic minerals - that is, up to the stage where the ores or concentrates were ready for hydro- or pyro-metallurgical treatment. This survey was carried on under the general supervision of L. A. Lyon, assistant director and chief metallurgist of the Bureau of mines, in cooperation with the milling committee of the American Institute of mining and metallurgical Engineers, the Massachusetts Institute of Technology, and the University of California. Other institutions, including the National Research council, were of assistance and outlined recommendations during the study.While this report is on ""ore dressing"", it contains short sections on coal and clay. The mechanical handling that these minerals undergo is ""dressing"", so that ore dressing is inclusive of metallic and nonmetallic minerals. ""milling"", in its broadest sense, includes with ore dressing certain other metallurgical treatment which the report is not designed to cover.The survey revealed that considerable experimentation is being carried on great cost to the mining industry, but that the research is in general poorly coordinated while companies and firms are adequately taking care of routine tests and the mechanical features involved in their own operations, no comprehensive study of the fundamental principles of ore reduction is now in progress or contemplated. Many industries, besides mining, are interested in the preparation of materials for final treatment, rendering this investigation of value also to them. This class of fundamental research is neglected by industry unless there is some agency which can bring together at least a majority of this interested in a cooperative effort. It can not be effectively handled by a single company; and, moreover, no company can be expected to bear the whole burden of an investigation to benefit the entire industry or a number of industries hence there is need for concerted study within reasonable limits. Furthermore, co-operation eliminates duplication, which is largely a waste of effort and capital."

Mar 1, 1925

By S. Akhtar

Interstitial compounds of iron, cobalt, and nickel, and their binary and ternary mixtures with silver, gold, palladium, and platinum were prepared and tested as fuel cell catalysts. The first step in the preparation of the interstitial compounds consisted of preparing finely divided metals. This was done either by the Raney method or by reduction of precipitated hydroxides of the metals. The finely divided reduced metals were then treated with carbon-and/or nitrogen-containing gases to prepare their carbides, nitrides, and nitrocarbides. The materials were tested for cathodic activity towards O2 and for anodic activity towards H2, C3H8, NH3, CO, and N2H4 in acid and alkaline electrolytes at 25° to 90° C in half-cell assemblies. Samples of carbided and nitrocarbided INi-lAg-1Au were about one fifth as active as Pt-black in the reduction of O2 in 35 percent KOH solution, whereas the activities of several interstitial preparations exceeded the activity of Pt-black in the reduction of O2 in 12M KOH containing N2H4. Nitrocarbides of x-Fe2C, 3Ni-1Au, and 1Ni-3Au were effective catalysts for oxidizing N2H4 in liquid NH3 containing NH4SCN. Corrosion of the catalysts by electrolytes was severe in many cases.

Jan 1, 1970

This report describes Phase I of the project --Development of a Mechanized Scaler --performed by Battelle, Pacific Northwest Laboratories for the U.S. Bureau of Mines. The objectives of Phase I were to 1) assess the needs of the industry as related to mechanized scaling; 2) conceive, evaluate and select mechanized scaler concepts; and 3) prepare preliminary designs of the selected machine concepts. To assess the scaling needs of the industry, we reviewed both U.S. and foreign literature, evaluated U.S. scaling accident statistics, reviewed existing mechanized scaling equipment, performed a series of mine visits and telephone interviews with mine operators, and assessed the applicability of a loose-rock detection system. The literature review identified over 25 scaler-related articles. However, little of the information could be used directly in the conceptualization and design portions of the project. Three articles did supply information on a number of machines used in Europe, along with statistics describing their effect on mine safety. For example, the French reported a 50% reduction in the total number of scaling-related accidents and a full 80% reduction in the number of lost-time injuries in the Lorraine mining district.

Jan 1, 1981

By D. T. Randall, H. W. Weeks

The burning of coal without smoke is a problem that concerns the Government directly because of the advantages of smokeless combustion both in public buildings and on naval vessels. In addition, smoke abatement is a factor in conserving the fuel resources of the United States. Hence, as part of its general investigation of the best methods of utilizing the coals of this country, the Bureau of Mines, which is in charge of the fuel-testing work formerly carried on by the United States Geological Survey, has made extended tests to determine the conditions necessary for the smokeless combustion of bituminous coal in boiler furnaces. Bulletin 39,a a preliminary report, treats the smoke problem from a theoretical point of view, detailing the steps that are being taken by . municipalities, manufacturers, and citizens to abate smoke, also showing the possibility of a clean city. The present bulletin not only shows that bituminous coals high in volatile matter can be burned without smoke, but also that large plants carrying loads that fluctuate widely, where boilers over banked fires must be put into service quickly and fires forced to the capacity of their units, can be operated without producing smoke that is objectionable. Proper equipment, efficient labor, and intelligent supervision are the necessary factors.

Jan 1, 1912

Geophysical Abstracts 1 - 86 wore issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 119 were issued in mimeographed form by the Bureau of Mines as Information it ion Circulars 7256, 7257, 7267, 7273, 7285, 7292, 7303, and 7310. 1. GRAVITATIONAL METHODS 7786. Barton, D. C.3/ Case Histories and Quantitative Calculations in Gravimotric Prospecting. Am. Inst. Min. and Meat. Eng., New York, Tech. Pub. 1760, 1944, 49 pp.

Jan 1, 1945

The Black Hills Mineral Atlas briefly summarizes all important data available on the mines and mineral deposits in the Black Hills that have been explored, developed, mined, or located. The purpose of the atlas is threefold; First, from available data the general potentialities of the Black Hills region can be determined, although it is not possible to calculate actual ore reserves; second, it will provide the necessary basic information regarding a given property or commodity for further detailed study; and third, the compilation is a comprehensive directory of Black Hills deposits.

Jan 1, 1955

By W. E. Foreman

A mathematical model was developed to assess the costs for reclamation of surface mining using the shovel overcasting operation, the front end loader operation, and a backfilling operation. A literature review was made of the present laws in Kentucky, Pennsylvania, Virginia, and West Virginia pertaining to surface mining and of the various parameters that influence the input data for a mathematical model. It was determined that the working mathematical model would have to be applied on an area to area basis, preferably on a permit by permit basis in the area where surface mining was being done. To this end, a flexible model was developed with input data obtained from the area of study. The results of the study show that the cost per ton of coal for reclamation can be estimated for various reclamation levels. Validation of the model was done for selected permits from Virginia. It was determined that the permits could easily be used for input data to the model.

Jan 1, 1974

By Charles W. Merrill

AN ADEQUATE, dependable, and continuing supply of raw materials is indispensable to tile the United States and its industries in meeting the needs of an expanding Population, a rising standard of living, and the national security. The primary responsibility for appraising the status of the country's mineral supply and for making appropriate recommendations within the executive branch and to the Congress has been pinned in the U.S. Department of the Interior. In fulfilling its role of governmental responsibility for raw-material supplies and their efficient utilization, the Bureau of Mines has analyzed the factors in current and future mineral supplies and demands and has developed 87 statements for specific commodities that assess the national position and problems for these metals, minerals, and mineral fuels. These statements, which constitute the chapters of this volume, are based on lire assumption that nearly till production and consumption of materials in the United States are to be by private individuals and organizations, in accordance with the Nation's devotion to a private-enterprise economy.

Jan 1, 1960

By Robert C. Merritt

Laboratory amenability studies as well as a pilot heap-leaching investigation of low-grade sandstone uranium ores from Wyoming, New Mexico, and Colorado are described. Sulfuric acid heap leaching with oxidation, for 120 days, extracted up to 98 percent, 90 percent, and 79 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively.

Jan 1, 1976

By D. Randolph Berry

This report describes a study to develop a detailed set of guidelines and equipment recommendations to be used as a guide for mine operators, mine inspectors, and equipment manufacturers in implementing the emergency escapeway standards for metal and nonmetal underground mines. It was sponsored by the United States Bureau of Mines. The first part of this report reviews the historical background of metal and nonmetal mine fires and the development of present and proposed mandatory standards. This is followed by a discussion of the survey of representative mines and how the proposed standard effects these mines. The remainder of the report covers technical discussions of each escapeway component including a comprehensive computer simulation of mine evacuation. Following the technical discussion of each group of escapeway components is a list of the pertinent guidelines. The major escapeway components discussed are the following: Escaperoutes Refuge Chambers Hoisting System. Escapeway Signs Ventilation Fuel Storage Fire Retardants Warning Systems Auxiliary Transportation

Jan 1, 1976

By J. W. Allen

This report reviews the work performed on Task M of Bu-Mines Contract H0220073 to develop an engineering model of a surface and subsurface communications system for normal mine operations and for post disaster rescue operations. The system concept provides for one-way transmission of digital information between a number of identifiable subsurface terminals or subcenters and a single surface station. It also provides 2-way voice communications between the subcenters and the surface station. The basic communications link is electromagnetic signaling through-the-earth, but the system is also capable of using mine phone lines as an alternate link. Engineering models of three subcenters and one surface terminal (see Figure 1-1) have been fabricated in order to demonstrate the system's performance. The system concept, however, permits up to 20 subcenters to be incorporated if desired. Additional subcenters are also feasible for large mines if they can be deployed in the mine to operate on a noninterfering basis.

Jan 1, 1973

By W. I. Nelson

This paper which describes the milling practice of the Engels Copper Mining Co., is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. ACKNOWLEDGMENTS Acknowledgment is made of the assistance rendered by J. Casagrande, mill foreman of the Engels concentrator, in collecting much of the data presented in this paper.

Jan 1, 1932

By G. A. Apell

"SUMMARYThe quality of Moose Creek coal is considered superior to that of any now being produced in the Matanuska field of Alaska. In rank it is classed as roar coking high-volatile B bituminous coal.At present the Moose -Creek mines are accessible from the Glenn highway by 6 miles of well-maintained gravel road. The nearest railroad loading point is Moose Creek siding; 7 miles by road from the Buffalo mine. Palmer, 12 miles south of Buffalo mine, is the nearest town. Anchorage is 50 miles south of Palmer by road and-railroad.Core drilling and trenching by the Bureau of Mines revealed 2,375,500 short tons of coal in the Buffalo series on the Buffalo Coal Co. leasehold. Of this, 514,200 tons is considered measured coal and 489,900 tons indicated coal. Existence of deeper beds over the same length increased the tonnage of coal of all categories to 3,279,300 tons. The property has an assumed life, of 16 to 22 years, depending on the number of beds mined, based on an output of 500 tons of coal a day and 100-percent recovery. Coal from some of the beds car be marketed without washing however, a washery is necessary if all beds are mined. Beds in the Buffalo series not mined in the ""first mining"" will be irrecoverable at any later date.The Bureau of Mines completed exploration of approximately one-third of the local coal-bearing areas during 1943. Knowledge gained from this work makes it possible to investigate the rest of the area by drilling an estimated additional 5,000 foot of hole."

Dec 1, 1944

By D. J. Parker

Because of its convenience and availability, natural gas (and to a much less extent manufactured gas) in being used more generally throughout the country for domestic and industrial purposes. With this use, specific and little-recognized hazards have arisen owing principally to the fact that the public and the consumer lack knowledge of the explosive property of this fuel. During the past 8 years gas explosions hove occurred in public and private buildings with loss of more than 300 lives and injury to many others. Such appalling catastrophes can and will be prevented if and when the necessary precautions are taken in the construction of buildings and the installation and maintenance of gas lines and gas appliances, plus adequate supervisions inspection, and education.

Jan 1, 1941

By B. K. Shibler, J. V. Batty, G. M. Potter, H. D. Snedden

"INTRODUCTION As a part of the investigations of strategic mineral deposits in the United States under the Strategic Minerals Act. Engineers of the Bureau of Mines examined and sampled numerous deposits pf fluoride ores in the Western States. Sample from those deposits that warranted further investigation were submitted to the Ore Dressing Section of the Salt Lake Station for metallurgical testing. This paper gives data summarizing the results obtained from laboratory studios of fluorite ores submitted from 12 deposits in Arizona, California, Idaho, Montana, Nevada and Wyomong. Only four of the Ores were found to be amenable to beneficiation for the production of acid-grade fluorspar concentrates with good recoveries. However, all of the samples were amenable to the production of concentrates meeting chemical specifications for metallurgical-grade spar.For the sake of clarity and convenience in presenting data, this report has been divided into six parts, each pertaining to metallurgical studies of fluorspar ores of a single State."

Nov 1, 1947

By Ralph B. Stevens

The objective of the Automatic Fire Sensing and Suppression Systems for Mobile Mining Equipment program is to document the design, fabrication, factory testing, 11-month in-mine testing, and final demonstrations of auto¬matic fire protection systems on several units of mobile mining equipment including trucks, front-end loaders, cranes, draglines, coal haulers, and cutters. Proper sealing of all system components from the elements, especially in corrosive mine conditions, is essential for reasonable life-cycles with minimum maintenance. Also, adequate power supplies, wire, connectors, and plumbing with adequate protection from the harsh mine environments and physical damage were necessary during the in-mine tests. The fire protection systems were developed from technology employed during two previous Bureau of Mines contracts: HO122053, Improved Sensors and Fire Sensing Systems for Mining Equipment, and H0232059, Validation Testing of Truck Fire Protection Systems.

Jan 1, 1978

By Arno C. Fieldner

This is the fifth of a series of annual reports4/ of technologic investigations conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal. The research of the Bureau is carefully coordinated with the requirements of the producing and consuming industries, with a view to conservation of resources of coal in mining and use, and conservation of the health and lives of workmen employed in these industries. Such coordination is facilitated by the wide range of specialization of the several groups on engaged in studies concerning coal. Here are reported correlated studies ranging from paleobotanic analysis of the formation of coal as it occurred some millions of years ago to the effect of mechanical methods of mining on present-day employment in mines. As this is a summary of the current work of the Bureau of Mines, so the Bureau likewise has provided a condensed review of the outstanding current work of others on research and technology of coal 5/.

Jan 1, 1940