Search Documents

By D. Harrington

Approximately 2,000 persons are killed annually in the coal mines of the United States. There is no question that this number is at least double and probably treble what it should be and by all means the least excusable of the fatalities are those caused by explosions and fires. Fatalities from explo- sions and fires in coal mines are almost invariably caused by carelessness or negligence. Table 1 indicates that the fiscal year ending June 30, 1931, ras by no means a satisfactory one as regaris either the number of explosions or the number of persons killed by them. This tabulation lists all ignitions to which the attention of the personnel of the safety division was called and in- cludes not only major disasters, but also explosions in which fewer than five were killed, as well as several explosions from which no fatalities resulted. It will be noticed that last year there were 26 explosions in mines in 10 States of the United States, resulting in 217 deaths. In the previous year there were 34 explosions with a death list of 199, and in the year before there were 38 explosions with a death list of 139. Hence, the past fiscal year had distinctly a poorer record of fatalities from mine explosions than either of the two previous years. Of the 26 explosions in the past fiscal year, Pennsylvania had 7, West Virginic 4, New Mexico and Ohio 3 each, Alabama, Oklahoma and Washington 2 each, and California, Illinois and Indiana 1 each; the one in California was in a tunnel being driven for water purposes but giving off explosive gas (methane). In fatalities Ohio had the worst record with 38, Oklahoma came next with 45, then Indiane with 38, and Pennsylvania with 23; although Alabama had 2 ignitions and Washington 1, they caused no fatalities. Utch, Colorado, and Kentucky had no explosions reported by the safety division of the Bureau of Mines during the past fiscal year, but were on the list for the previous year, though in the case of Colorado there were no fatalities. On the other hand, Indiana and New Mexico, neither of rhich was charged with an explosion in the two previous years, were on the list for the past fiscal year; New Mexico had the bad record of three explosions, though fortunately with but a total of eight fatalities. Ohio reported 3 explosions to the safety division of the Bureau of Mines in the past fiscal year, 2 in the pre- vious year, and 3 in the year before that, or 8 in the past three fiscal years with 92 fatalities; all of these eight explosions were in open-light mines.

Dec 1, 1931

By H. William Zeller

The Bureau of Mines performed laboratory research into the effects of a barium-based fuel additive (the "postflame" type) on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of types certifiable for use in underground mines. Test parameters consisted of additive concentration and engine loads, speed, and air intake restriction. DPM emissions, including condensed volatiles, were measured gravimetrically. Also measured were gaseous emissions including carbon monoxide, nitrogen oxides, and hydrocarbons. The fuel additive was effective, reducing DPM up to 75 pct, when used at a concentration of 0.09 wt pct (one-fourth of the concentration recommended by the manufacturer). The additive was most effective at the highest fuel-air ratios, reducing DPM from 400 mg/m3 for untreated fuel to 120 mg/m3. At light loads, 25 pct of full rated, no DPM reductions were measured. Based on these results, the additive is recommended for use in diesel fuel, at a concentration of 0.09 wt pct, to power underground mining equipment as long as certain conditions are met: that a beneficial DPM reduction is verified, that the minimum required quantity of additive is used, and that potential adverse effects such as increased nitrogen oxides are checked.

Jan 1, 1990

By Barry Beith

This report details a study which was designed to assess the effect of retroreflective material on detection and form recognition of workers in the mining environment. Further, the study attempted to determine an optimal configuration of retroreflective material with respect to amount and placement on the body to facilitate detection and form recognition. The study involved a one-fifth scale simulation of the perceptual task found in the underground low seam coal mine. Four different configurations of reflective material were presented in various body positions, common to low coal miners, at three different locations in the visual field, i.e., 10, 25, and 45 degrees from focal line-of-sight. All reflective configurations significantly improve detection and form recognition over configuration (cap only) worn by miners. As the amount of reflective material increased, accuracy also tended to increase. Based on the configurations investigated by this study, the Armband configuration (i.e., refectorized armbands, belt, self-rescuer and battery pack) was determined to be optimum. It is recommended that an actual field evaluation be made using the Armband configuration to establish if simulator results are generalizable to the underground mining environment.

Jan 1, 1980

By D. Harrington

More or less unconsciously and from sheer force of habit human beings do many things they probably would not do if the possible consequences of their acts were fully recognized and appreciated. Such carelessness ordinarily could be condoned if human life were not at stake, but it is difficult to understand why intelligent men engaged in the hazardous occupation of mining indulge with the utmost indifference in some habit or continue some custom in violation of State leas and company regulations and under circumstances that may jeopardize not only their own lives but those of scores, even of hundreds, of their fellow workers as well. The old adage that stolen sweets are the best may or nay not have some foundation, but when applied to the practice of smoking surreptitiously in a coal mine, more especially a gassy mine, it is without even remote justification. Although a relatively harmless habit in the proper environment, smoking has been the cause or suspected cause of many gas explosions and black-powder ignitions and has resulted in numerous instances of bodily injury, loss of life, and destruction of property. Likewise, many fires in both coal and metal nines, causing loss of life, have been started by smoking.

Jan 1, 1941

By L. C. IlsLey

Permissible blasting units are approved with the understanding that if actively marketed they will be listed as permissible so that all interested in such safety equipment may know what is available. The last detailed lint of permissible units was published as Technical Paper 4294/. All of the blasting units of that list have become obsolete or have boon modified as covered by extensions of the original approvals.

Jan 1, 1941

By Aner W. Erickson

"Preliminary examination of tungsten deposits on the Mountain View property near Hyder, Alaska, was made by Neal M. Muir, an engineer of the Bureau of Mines daring the summer of 1942. Fifteen samples were cut, rough esti¬mates of ore reserves were made, and it was proposed to extend the drift on scheelite-bearing vein 300 feet in a northwesterly direction.From May 22 to October 24, 1944, an exploratory project was conducted on the property by the Bureau. In the course of this work, the camp buildings were rehabilitated; the dam, hydraulic line, and machinery were repaired; 226 feet of drift was driven; 80 groove samples aggregating 3.9 tons in weight were cut; a 6,000-foot surface and underground traverse was run; and the area was mapped in detail.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is doe Neal W. Muir, project engineer, and Robert S. Sanford, acting chief, Alaska Division, Mining Branch, for their supervision of the field work and revision of the report.Acknowledgment is also made to Silbak Premier, Ltd., for rendering valuable assistance in the repair of equipment and for extending various courtesies to Bureau of Mines personnel during the conduct of this project.The Mountain View property is located at latitude 55° 59' north, and longitude 130° 03' west in the Salmon River mining district of southeastern Alaska, about 5 miles in a northwesterly direction from the town of Hyder, which lies at the head of Portland Canal, as shown in figures 1 and 2. Vein outcrops and surface workings are at an elevation of 950 feet and occupy the west flank of a low ridge between Skookum and Fish Creeks, as shown in figure 3. The portal of the long adit exposing the vein at depth is on Skookum Creek about 550 feet north of the confluence of Skookum and Fish Creeks.Access to the property is over a 4-foot wide trail built and maintained by the United States Forest Service. This trail is suitable for pack animals and is adequate for transportation of supplies and material for exploratory work. During the periods of camp construction and past exploratory operations a 4,000-foot, single-cable, aerial tramway, now in disrepair, served for transportation of materials and all machinery from the Salmon River Highway to the property. The cost of such hauling was high, amounting to $12 a ton. Topography is suitable for construction of a ""cat road"" 2 miles in length, connecting the property with the Salmon River Highway. It is estimated that such a road could be built for $5,000 a mile, and supplies, machinery, and concentrates could be haled over it at a cost of less than $2.50 a ton."

Sep 1, 1946

By K. K. Kelley

Synthetic fluorphlogopite mica (KMg3AlSi3010F2) is a relatively new product developed at the Norris (Tenn.) Station of the Bureau of Mines, Thermodynamic data have applications both in the production and use of this product, and the work described in this paper was undertaken to fill the need for such data. Measurements were made of the heat of formation at 298° K., the heat capacity between 50° and 298° K., the entropy at 298° K., and the heat-content and entropy increments between 298° K. and a maximum of 1,804° K. These basic data are combined to obtain heats and free energies of formation of the mica from the elements and from molecular constituents at temperatures ranging from 298° to 1,800° K. Minimum heat requirements to form melted mica from commonly used ingredients were calculated.

Jan 1, 1959

By Bruce K. Cantrell, Jon C. Volkwein

Exposure to mineral aerosol is an occupational health hazard in mining and mineral processing industries because of the risk of developing pneumoconiosis. Agricola (1556) described this hazard for metal mining in Carpathia. He described shortness of breath and consumption, conditions that are now associated with asthma and emphysema. By the end of the nineteenth century, several respiratory diseases were known to affect miners, including silicosis and coal workers' pneumoconiosis (Fletcher, 1948; Seaton et al., 1981). For example, silicosis, not tuberculosis, was clearly recognized as the hazard in the Vermont granite quarries and stone-cutting sheds (McFarland, 1927). The Gauly Bridge Tunnel disaster in the mid-1930s caused the deaths of an estimated 700 workers by acute silicosis and focused the nation's attention on this disease (Cherniack, 1986). By the mid-twentieth century, it was clear that risk of simple pneumoconiosis is associated with a miner's cumulative exposure to mine aerosol in the respirable size range and that prevention lies in reducing that exposure through regulation (Seaton, 1986). In the United States, regulation of mine worker exposure to airborne mine dust is the responsibility of the Mine Safety and Health Administration (MSHA) in the U.S. Department of Labor. The key legislation relating to improved mine worker health was the Federal Coal Mine Health and Safety Act, enacted in 1969 (U.S. Congress, 1969) and subsequently amended as the Federal Mine Safety and Health Act of 1977 (U.S. Congress, 1977). MSHA receives technical assistance from the National Institute for Occupational Safety and Health (NIOSH). NIOSH also provides recommended exposure limits (RELs) for contaminants to MSHA. MSHA's regulation of mines includes the establishment of a dust standard administratively based on the these RELs. Some mine operators must submit a dust control plan designed to meet the dust standard. Periodic mine inspections determine if mines are com- plying with both the dust standard and the dust control plans (MSHA, 1991). The most common dust measurements are those for respirable dust (according to the definition given in Fig. 26-7), that is, the fraction of aerosol particles able to reach the gas exchange region of the lungs. The other health-related size fractions (inhalable and thoracic-see Fig. 25-1, and "total" dust) are also occasionally measured. A "total" dust measurement is defined by the common practice of the last 30 years or so, using 25 mm or 37mm plastic cassettes (e.g., from PAL, MIL, SKC ). The types of mines have been categorized

By Murray Jacobson

Data obtained by the Federal Bureau of Mines on the dust explosion hazard in air are presented for 220 samples of agricultural products. Information is given on ignition temperature of dust clouds and layers, minimum explosive concentration, minimum electrical energy for ignition, explosion pressure and rates of pressure rise, amount of inert dust required to prevent flame propagation, and, in a few instances, the permissible oxygen concentration in an atmosphere to prevent ignition by spark and by heated surface. The effects of particle size and source of sample on explosibility are shown. The relative ignition sensitivity, severity of explosion, and overall explosibility of the materials are characterized by empirical indexes. This report contains Ma obtained by the Bureau in laboratory studies on the explosion hazards of agricultural dusts. Recognition of the dangers will encourage adoption of adequate measures to prevent ignition and explosion during preparation, processing, and utilization of the materials. Agricultural products constitute one of the largest groups of materials used in America. More than 260 million tons of various grains, much of which now exists in dust form, was grown in 1958.6/ Over 600,000 tons of the annual production of 200

Jan 1, 1961

By R. J. Morrell

The Bureau of Mines conducted a series of laboratory experiments to test a cutting technique for hard rock using large-scale drag cutters. Cutting experiments were performed on rocks ranging in compressive strength from 10,000 to 27,000 Ib/in2, using large drag cutters from 3 to 6 in. in width. The tests were conducted on a special test apparatus, called a ripper tester, which made a curvilinear cut across the rock sample while measuring the cutting force acting on the drag cutter. The cutting method that evolved from these experiments is called ripper cutting, and its energy efficiency appears superior to all other large-scale mechanical fragmentation techniques. In addition, the method cre-ated very little dust, and the wear on the bits was negligible. A fragmentation system based on ripper cutting was then devised, and a large-scale test device was fabricated to allow full-scale laboratory testing of the system. The results of these tests will be published in future Bureau reports.

Jan 1, 1986

By E. D. Gardner

This paper discusses prospecting for lode gold and lists the principal lags and. regulations pertaining to locating; lode claims on public lands. It is a preprint of a part of a bulletin being prepared by the United States Bureau o Mines entitled "Equipping, Developing and Operating Small Gold Mines". The increased interest in gold mining manifested during the past few years (1932-1935) bas stimulated prospecting. Many adventurers have taken to the field to search for now gold deposits. A. large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the tope that it might assist these newcomers.

Jan 1, 1935

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,680 samples, representing the products of 130 companies. The samples were collected during December 1953 and January and February 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past ten years is given on page 5.

Jan 1, 1954

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

By Spencer P. Howell, J. F. Xrawshaw

"A recent premature explosion in a quarry that resulted in the death of nine men and the injury of several others, was directly traceable to a spark from a steam-shovel working under the face directly in front of the hole being loaded. This accident and similar accidents on record in the Bureau of Mines indicates the necessity for pointing out the dangers in quarries of explosives being ignited by sparks emitted from steam shovels and locomotives, and making recommendations for greater safety.Many premature explosions of which the following are examples, have resulted from sparks, both from steam shovels and passing locomotives. (A) The premature explosion occurred during August, 1920 at a limestone quarry, in a 100-foot drill hole, loaded with 1000 pounds of high-grade nitroglycerin and gelatin dynamites. This hole had been loaded with 500 pounds of 75 per cent strength gelatin dynamite, 300 pounds of 60 per cent straight nitroglycerin dynamite, and 200 pounds of 50 per cent straight nitro¬glycerin dynamite; but no steaming had been placed in the hole. The powderman loading the hole saw the spark enter the hole and was able to run a short distance before the explosion took place, thus escaping serious injury. The explosion of this first hole was transmitted to nearby hole similarly charged. The fall of rocks from these two holes buried the steam shovel and some of the gang of men working around it.(B) In September, 1909, in the Canal Zone, a steam shovel uncovered a misfired charge of dynamite. While the dynamite was being picked up the steam shovel continued working nearby. A spark from the shovel set fire to some loose dynamite spilled on the ground from the troken cartridges. This fire was transmitted to a hole which was being loaded close by and caused a premature explosion. One man was injured."

Nov 1, 1920

By R. P. Maloney

The Bureau of Mines conducted a reconnaissance of the less accessible parts of the Beluga River coalfield in August 1957 to determine, if possible, which areas were most favorable for developing large reserves of coal suitable for open-pit mining. Several outcrops of subbituminous coal were observed within an area about 30 miles long and 3 miles wide; neither the length nor the width of the coal-bearing area was delineated by the examination. Coal beds 30 feet thick or more outcrop at two places, and beds 5 to 20 feet thick or more outcrop fairly abundantly along the Beluga River and its tributaries The coal measures appear to occur in a series of folds. The overburden comprises glacial gravels and poorly cemented sandstones and ranges from 20 to 400 feet in depth. Few partings were seen in any of the coal beds. Samples ranged in calorific value from 6,240 to 8,246 B. t. u. on an as-received basis. Adequate water is available for stripping by hydraulic methods.

Jan 1, 1958

By R. C. Bates

Uranium mine workers? daily exposure to radon daughters was estimated by two methods of sampling, detailed and spot-check. Both methods involve time- weighting measured exposure levels to arrive at an average exposure figure. Random sampling, or sampling without regard for the duration of exposure, has proved inadequate for estimating average exposure levels. During the first phase of the study, the breathing zones of eight workmen in three underground uranium mines were sampled for an entire shift; 20 to 36 radon-daughter samples were collected per man-shift, Analysis of these data indicated that a suitably accurate estimate of the full-shift exposure could be made by time weighting a considerable lesser number of representative radon-daughter samples. This analysis led to the spot-check method of estimating full-shift exposures to radon daughters. Additional detailed studies were made in seven mines to Learn more about the full-shift radon-daughter exposures and to test the spot-check method, In all, 617 radon-daughter samples were taken in 10 underground uranium mines during 26 man-shifts, and the spot-check method was tested 35 times.

Jan 1, 1962

By GEORGE T. Harley, Walter R. Storms

This paper, which describes mining mothods at International Minerals & Chemical Corp, 'e. potash mine. in. Eddy. County, N. Mex., is one of a sories being prepared by the Mining Branch of the Bureau of Minos. on mining method a and practicos in, various mining districts of the United States. The mine shafts and. surface plant or International Minerals & Chemical Corp. are situated. in. sec.. 12, T. 22 S., R. 29 E., N. M. P. M., about 26-1/2 miles by paved highway east of the city of Carlsbad (figs. 1, 2, and 3). A spur line of the Atchison, Topeka & Santa Fe Railroad connects the mine with the Clovia-Pecos branch of the same road near Loving, a few miles south of Carlsbad. This spur also serves the refinery of United Staics Potash Co. This report gives. the history and describes the geology of the district. Methods of prospecting, exploration, sampling, and estimation of tonnage and values are explained; development and mining methods are discussed in con- siderable detail; transportation, ventilation and drainage are outlined; safety measures are noted; and the wage scale and organization are mentioned.

Jun 1, 1949

By W. P. Yant

[At the majority of mines where flame safety lamps are used either as working lights or as a means of detecting gas, no check it made on this condition of the various parts of the lamp and their assembly other than a visual ink inspection. Although this inspection should be made carefully in view of tae serious consequence that may follow Vie use of a faulty lama, In many instances the inspection is of a perfunctory nature. The Bureau of Mines has therefore designed a small box or gallery for testing lamps for defects and improper assembly before they are taken into the mine. The test simulates the condition when a lamp is extinguished by its introduction into an explosive mixture and the operator attempts to relight the wick while the lamp contains the explosive mixture. This test is more rigorous than merely subjecting a lighted lamp to an explosive methane-air mixture. In the latter test the products of combustion tend to blanket the propagation of flame from within the lamp to the exterior, especially if there are defects at the top of the gauzes. Moreover, when the lighted lamp is subjected to an explosive methane-air mixture the methane builds up slowly within the lamp until the lower inflammable limit is attained, whereupon a feeble explosion occurs within. If the nonlighted lamps is first filled with the methane-air mixture that gives the maximum violence and is than ignited, the dampening effect of products of combustion is obviated and the strain on defects is]

Jan 1, 1930

By H. S. Chiang, Y. Luo, S. S. Peng

"IntroductionThe way in which the particle sizes distribute in the airborne coal dust plays an important role in the transportation of the dust in the mine air and human respiratory systems. Though the particles of a size less than 10 microns could be inhaled, the real distractive portion of the dust is that the sizes range from 1 to 5 microns since only they can reach the lungs and be retained there. Those with an equivalent diameter larger than 5 microns will settle on the membranes of the branchial tubes(1) while those with diameter less than 1 micron can either be exhaled out of the lungs or the settled quantity is so insignificant that does very little harm to the lungs. In the transportation process, the finer dust will fly farther away from the sources than the coarser ones. Thus once the fine dust is generated and becomes airborne, it will spread out to a larger area.In this paper, the coal samples collected from two longwall faces were analyzed statistically for size distribu¬tion. A mathematical model is proposed and the effects of different conditions on the dust size distribution were analyzed using the mathematical model.Sampling and Statistical AnalysesSampling Instrument and ProcedureThe instrument used in the sampling were Mine Safety Appliance (MSA) personal sampling units equipped with 10-mm nylon cyclones, pre-weighed MSA PVC filters and constant-flow pumps.Two longwall operating faces were selected for the dust sampling. The two faces were located in two coal mines ex-tracting Pittsburgh seam. The double-ended ranging-drum shearer applying the unidirectional cutting sequence was employed. The two-leg shield supports were used for face support. The width of the two faces was about 215 meters.In each of the two faces, four sampling stations were set up. The stations were located at the cross-cut immediately outby the headentry side, the 15th support (25 m), 65th support (107 m) and 111th support (182 m) from headentry T-junction, and numbered as #1, #2, #3, and #4 station, respectively (Figure 1). At each sampling station, a group of three sampling units was hung at proper position. At cross¬cut (#1) station, the units were hung about one foot under the roofline in the center of the cut (Figure 2a), and at the stations in the face, the units were position near the hydraulic legs and one foot below the support canopy (Figure 2b).One complete set of 12 samples was collected for each day. The sampling were performed for five consecutive days. All the samplings were conducted in the morning shifts. The time duration of the sampling for each day was about five hours. During that time, the shearer might complete 5 to 7 mining cycles."

Mar 1, 1989

By Frank C. Andreuzzi

The Federal Bureau of Mines conducted a demonstration project to reclaim 125 acres of abandoned strip-mined land in Lackawanna County, Pa., for public recreational, historical, and educational use as a park. The Bureau was involved in the development of the general site plan, and engineered and supervised the basic land rehabilitation. The park's Facilities include outdoor recreational activities, picnic grounds, children's play areas, primitive overnight camping, and winter sports. A major attraction is the Anthracite Museum constructed by the Pennsylvania Historical and Museum Commission The project may serve as a prototype for reclaiming existing and future surface-mined lands.

Jan 1, 1976