Search Documents

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state's underground mines. By 1884, North Dakota's lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota's regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992

By R. B. Crookston

Oil shales differ from coals in that they contain less carbonaceous material, convertible to volatile hydrocarbons, and more inorganic rock. In all pre-commercial oil shale development, involving extensive full scale mining operations, there have been no explosions. However, large scale mine tests with oil shale dusts by the Bureau of fines showed that propagating explosions could be induced under certain circumstances. Laboratory tests were conducted on a broad spectrum of oil shale dusts to define chemical properties and to seek correlations with subsequently determined fire and explosivity properties. These latter properties, indicative of safety hazards, increased as the Fischer assay oil yield of the dusts increased and as particle size decreased. Laboratory data were used to relate fire and explosivity properties of oil shales to those of coals and other carbonaceous materials and to assist in the identification and evaluation of potential hazardous situations which may be encountered in oil shale mining and processing.

Jan 1, 1978

By Chas. G. Maier

The absence of plants on the Pacific coast for the reduction of iron ores usually is attributed to the fuel situation there. Thus, the bulletin of the. State Division of Mines for 1933, entitled "California Mineral Production," says: "There are considerable deposits of iron ore known in California, notably in Shasta, Mad era, Placer, Riverside, San Bernardino, and Los Angeles Counties, but production has so far been limited for lack of an economic supply of coking coal." It has been estimated that the six major steel plants of the Pacific coast have an annual ingot capacity of 600,000 tons. The present need for tin plate averages 300,000 tons yearly for California alone, of which some 12 percent is manufactured locally. If the consump¬tion of other iron and steel products in 1929 may be taken as an approximate, estimate of the normal requirement for such products, it may be estimated further that, 65,000 to 75,000 tons each of cast-iron pipe and steel reinforcing bars and 300,000 to 400,000 tons of structural shapes and plates will be required annually in California.

Jan 1, 1936

By J. D. Warne

The ferberite district of Boulder County, Colo., has been an important producer of tungsten since 1900. During World War I, high prices for tungston concontrates resulted in a brief period of intense activity, and the production in 1917 was 2,707 tons of 60 percent W03 concentrates. Production declined thereafter, and in 19.2 the tungsten produced in Boulder County represented about 4 percent of the Nation's output, being exceeded only by the scheelite production in California, Nevada, and Idaho. Boulder County has boon an important source: of tungsten in the Korean emergency; the present report does not describe this recent activity, as it will be covered by a future publication. Tungsten occurs in small ore shoots of narrow and irregular veins. Most of the ore shoots have been found outcropping on the surface. Core drilling; has been used by the larger operators to explore for new veins and to locate extensions of known veins.

Jan 1, 1953

By E. L. Garton

The oil-producing district, "Southern Oklahoma," is generally considered to be that part of the: State lying southwest of the Arbuckle Mountains. It includes six counties: Cater, Cotton, Garvin, Jefferson, Kiowa, and Stephens. At present cost of the oil is produced from formations of Pennsylvanian age. The individual crude oils resemble those produced in other parts of the State, except that the sulfur content is rather high. This report is a continuation of a study of Oklahoma crude oils3/being made, by the Bureau of Mines, Petroleum Experiment Station, Bartlesville, Okla. in cooperation with the State of Oklahoma. Analyses are given of 27 samples obtained from 21 fields in the southern part of the State, end the physical and chemical characteristics of these crude oils are discussed briefly. Analyses of crude oils from other Oklahoma areas and publications in which these analyses may be found are listed in tables 2 and 3.

Jan 1, 1941

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In with this request a preliminary review has been made of trends in the production and uses of block granite.. Some unfavorable conditions were thus brought to light, and certain suggestions regarding a more orderly and consistent growth in the industry are herein discussed. The results of the study are, presented in this report for the earnest consideration of. the industry, and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of Mines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable assistance through her wide knowledge of granite statistics. The block granite industry has shown little expansion during recent years. While the value of the annual production has grown from about $14,000,000 in 1904 to nearly $25,000,000 in 1928, the increment in value is caused mainly by mounting prices rather than by increased production. Even granite for memorials shows a very small advance in production volume, although the value has increased from about $3,500,060 in 1904 to more than $11,000,000 in 1928, which is the most consistent growth of any branch of the industry. The value of building granite has fallen for a number of years much below the figure for 1904, and in 1928 was very little in advance of the value attained 24 years previously. The use of granite paving blocks and rubble has shown a gradual decline.

Jan 1, 1931

By Everett P. Partridge, J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly in the form of byproduct salt cake from the acid manufacturers, has been tending to decrease this to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the kraft-paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This demand is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorably situated domestic deposits of Glauber salts and the anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2 504 • 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of the total weight of the crude salts and therefore has a very important influence on transportation costs, in many instances the cost of getting even the dehydrated product to market is the deciding economic factor. Therefore, the recovery of production of anhydrous sodium sulphate from plant-waste liquors or from natural brines of suitable composition might be economically feasible.

Mar 1, 1936

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instruction3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1969

By Shouchen Dun, Zong-Ming Li

Manipulation of hand-held objects in 3D space is a complex task. Understanding how individual digits interact with a hand-held object provides helpful information for hand tool designers, researchers, clinicians, and occupational therapists. At the object-digit interface, the contact mechanics can be represented by three force and three torque components. Six-component force/torque transducers can register all the three forces and three torques at the digit-object interface, and therefore are advantageous in the study of manipulation mechanics. The large number of force and torque signals from multiple force/torque transducers are difficult to interpret and therefore making experimental research of manipulation a challenging task. The purpose of this study was to develop a 3D visualization tool for the investigation of the contact mechanics at the object-digit interfaces during manipulation tasks. Methods A 3D stick-figure hand model was created based on digitized 23 anatomical landmarks of the hand. Five miniature 6-component force/torque transducers (4 × Nano17 for the fingers, 1 × Mini40 for the thumb, ATI Industrial Automation, NC) were used to record force and torque data at the tips of individual digits. Thirty channels of force/torque signals from the transducers were collected by a 16-bit analogue-digital converter (PCI-6031, National Instrument, Austin, TX) installed in a computer. The transducers were mounted on a custom-made rectangular aluminum handle for object manipulation. Coordinate frames were established at each transducer, on the handle, and at the base of the MicroScribe digitizer. To visualize the force vectors at the digit-tips, the coordinates of the hand landmarks in the MicroScribe coordinate frame and the force vectors in local transducer coordinate frames were transformed to a common coordinate frame defined on the handle. One healthy right-handed, male subject participated in the experimental study. During the tests, the participant sat in a chair by a testing table. The forearm was strapped to an arm holder in neutral rotation position. The instrumented handle was fixed on the testing table by a C-clamp through an adapting plate. With the hand of the subject gripped on the instrumental handle, the landmarks of the instrumented handle and the transducers, as well as the anatomical landmarks of the hand were digitized using the MicroScribe digitizer for the purpose of coordinate frame establishment and transformation as described above. The subject performed three different maximum isometric voluntary contraction tasks: (1) grasping, (2) rotating in pronation, and (3) lifting. Results The 3D hand model and representative force vector clusters in a single trial of grasping, rotating, and lifting tasks are shown in Figure 1. Each cluster was formed by displaying all the 3D force vectors during the period of “stabilized” maximum effort in a trial. The magnitude and

Jan 6, 2006

By Robert G. Gibson, Joel D. Gibbons

Measurements and analyses were conducted of whole-body vibration aboard seven commercially available passenger and/or recreational vehicles: sedan; sport-utility vehicle (SUV); pickup truck; moving truck; motorcycle; all-terrain vehicle (ATV); and boat. The purpose of the testing was to measure and assess whole-body vibration exposure in a range of typical vehicle environments in order to gain understanding of typical exposure levels characteristic of activities of daily living. Vehicle models tested (and model year) were: Ford Taurus (1995); Jeep Cherokee Sport (2000); Toyota Tundra SR5 (2002); Ford F-350 (1997); Harley-Davidson Electra Glide Classic (2004); Yamaha Kodiak 400 4x4; and Steiger Craft Model 21 Montauk. All vehicles were tested with their standard factory-installed seats and were operated under a range of normal operating conditions and speeds typical of intended vehicle use. Methods The measurement, processing, analysis, and exposure assessment methods follow the guidance of generally accepted, national and international consensus standards relevant to the evaluation of whole-body vibration, including ISO 2631-1 [1] and ANSI S3.18 [2]. Seats were instrumented with low-mass triaxial accelerometers mounted in seat pads. Accelerometers used in the test are specified to have flat frequency response over the frequency range of 0.5 to 80 Hz, and all accelerometers were recently calibrated traceable to the National Institute of Standards and Technology (NIST). Seat pads were installed following guidance in the relevant standards [1, 2], with sensitive axes of the accelerometers following the standard coordinate system with respect to the seated occupant. (The x-axis represents fore-aft motion; the y-axis represents side-to-side motion; and the z-axis represents vertical motion with respect to the occupant.) Vibration data processing and analysis, including filtering, sampling, frequency-weighting, averaging, summation, and determination of basic and additional metrics followed procedures in the relevant standards [1, 2]. Digitized time series data were acquired and stored using a PC-based data acquisition system. Whole-body vibration exposure analyses were conducted via post-processing. During data processing, recorded periods of seat acceleration that were identified and verified as resulting from occupant-induced motion rather than vehicle motion were excluded prior to exposure analysis. The basic evaluation metric for whole-body vibration is the frequency-weighted root-mean-square (r.m.s.) acceleration, aw. The primary additional evaluation metric is the fourth-power

Jan 6, 2006

By Edwin B. Cook

Studies of flame and combustion phenomena at the Bureau of Mines have been facilitated by computer evaluation of the thermodynamic properties of gases formed by constant-pressure burning.4 5 This report is the sixth of a series6-10 presenting results of such calculations; it deals also with constant-volume deuterium-air flames.

Jan 1, 1961

By McMillan W. D.

Vermiculite is the name of a group of micaceous minerals characterized by their property of exfoliating when heated and thereby increasing many times their original volume. The resulting product has excellent heat-and sound-insulating properties, is used as a lightweight aggregate, and has numerous other industrial applications. Deposits of vermiculite occur in areas of pre-Cambrian rocks of the Llano uplift of central Texas, particularly in Burnet and Llano Counties. Because of the growing economic importance of vermiculite products, the Bureau of Mines undertook a detailed investigation of several deposits in Llano County. This investigation was completed in February 1947. The work comprised topographic surveys of five deposits, drilling with a 4-1/4 inch Parmanco power auger drill, and laboratory evaluation of samples. 342 drill holes, aggregating 4,905.5 feet, were completed, and 377 samples were taken. Laboratory evaluation of the vermiculite comprised expansion tests on both crude and beneficiated samples. The products obtained were compared with commercial-grade vermiculite from Montana.

Jan 1, 1949

By Lyman Moore

This Bureau of Mines report describes 2nd evaluates iron ore resources in California and Nevada and analyzes the California and Japanese iron ore markets in which these resources will be used. The competitive position of California-Nevada ores, in these markets, was estimated by comparing regional iron ore prices, production costs, and transportation costs with those of foreign suppliers. Resources were determined to be sufficient to produce the equivalent of 585 million tons of 64-percent iron pellets at a price of less than $15 per ton delivered at California ports. Much higher tonnage could be produced at higher prices. Iron ore requirement of the California iron and steel industry will increase to an estimated 15.9 million tons by the year 2000. A study of the iron ore production potential of California-Nevada deposits and of out-of- State sources indicated that this ore requirement can be supplied most economically by California-Nevada ores. Iron ore import requirements of the Japanese iron and steel industry will increase to an estimated 150.0 million tons by the year 2000. A study of price trends in this market indicated that very little California-Nevada iron ore will be sold in Japan after 1973 when existing sales contracts expire. Iron ore-exports might be economically possible if ore could be transported from California to Japan at ballast rates as backhaul on existing petroleum shipping.

Jan 1, 1971

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In compliance with this request a preliminary review has been made of trends, in, the production and uses of block granite. Some unfavorable conditions, were, thus brought to light and certain suggestions regarding a. more orderly and consistent growth in the industry are herein discussed. The results of the study axe, presented in this report for the earnest consideration of the industry and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of twines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable, assistance through her wide knowledge of granite statistics.

Jan 1, 1931

By W. H. Kerns

The Taylor Creek lead-zinc deposit is on Taylor Creek, approximately 1-1/2 miles from tidewater, at the head of Duncan Canal, on the east side of Kupreanof Island, Petersburg district, southeastern Alaska. The property was located in 1903, and a 30-foot discovery cut was put to the west tank of the creek. Very little prospecting end developing has been done since that time. The property was examined by J. C. Roehm, associate mining engineer, Territorial Department of Mines, Juneau, Alaska, in June 1946. From exposure n the creek, a mineralized zone with possible dimensions of 1,700 feet by 1,000 feet was indicated. The general strike was northwest, and the dip was low and variable to the northwest. During September through November 1948, the Bureau of Mines conducted a project on the property. Four diamond-drill holes, totaling 770.5 linear feet, were drilled from the surface and 280 lineal feet of hand trenching done. The mineral deposit was found to occur as patches that appear to be a replacement in dolomitic limestone. The patches of mineralization are small, irregularly shaped, and irregularly distributed. Maps showing the location of the drill holes and trenches, analyses of the cores from the drill holes, and anal lee of the samples from the trenches accompany this report (see, also, appendixes A, B, and C).

Jan 1, 1950

By Edwin A. Clarke

[For almost 2 decades the Bureau of Mines has been Interested in converting solid fuels to liquid fuels. Small-scale laboratory investigations were carried on for a number of years.4/ This work wad expanded substantially under authority of Public Law 290, approved by the 78th Congress on May 5, 1945. As part of the. broadened program, coal-hydrogenation demonstration plant was designed and erected at Louisiana, Mo., where: hydrogen-manufacturing and compression equipment, shoes, electric power, and other utilities and facilities were available from a discontinued wartime ammonia works . The plant uses the direct -hydrogenation or Bergius process, but the process differs from prewar European practices in many respects. Many noteworthy improvements h eve bean made, particularly by substituting automatic instruments for manual control of process variable's, in line with modern American processing practices. The over-all objective of the demonstration plant is to bridge the gap between laboratory end commercial-scale operation by furnishing cost and engineering data to develop a synthetic liquid-fuels industry when it proves technically and economically justified. Fitting into the over-all program, specific objectives o early runs were to (1) train personnel who had no experience with this type of operation, (2) break in the installed equipment, (3) obtain successfully integrated operation of the entire plant, and (4) work towards obtaining data on the hydrogenation of coal-tar oil and a typical low-ash coal. In beginning fan integrated operation, it is common practice to operate and obtain reaonably smooth performance of each unit before the over-all operation is undertaken. The first part of the plant completed was the refinery, consisting of several fractionating systems, a stabilizer, and a chemical treater.]

Jan 1, 1953

By Grant R. Brown

This report presents the results of a study examining the relationship between supervisor characteristics and performance in underground coal mines, The specific objectives of the research include; document tasks performed by first-line supervisors during a normal shift; explain why supervisors carry out their duties as they do: identify salient characteristics of effective first-line supervisors; and formulate criteria for selecting and developing candidate supervisors. To accomplish the study objectives, on-site observation and data collection was carried out at 13 underground mines in Illinois, Ohio, and Pennsylvania. One hundred thirty-eight first-line supervisors were observed during a full work-shift and discussions with the supervisors and the mine superintendent were held during the course of the visit. The observational data from the study provide a detailed description of what supervisors to during their shift. The report begins with an introduction discussing the problem being studied and objectives of the research. The literature related to supervisor selection is then reviewed. The following section describes the research design including data collection procedures and statistical methodology used in the study. The next sections present the analysis of mine, section, crew, and supervisor characteristics. The report concludes with a discussion of the results of the study and recommendations concerning supervisor selection and development.

Jan 1, 1987

By Phillip M. Busch

VANADIUM was discovered in 1801 by Andres Manuel del Rio, a professor of mineralogy at the School of Mines in Mexico City. Del Rio called the new element erythronium. Later, he decided that this was not a new element but a form of chromium. Not until 1831 did Nils G. Sefström, a Swedish chemist, positively determine that the metal was a new element which he named vanadium, after Vanadis, the Scandanavian goddess of beauty. From 1831 to the 1860's and 1870's, the comparative scarcity and high cost of vanadium restricted its commercial use. Shortly after 1870, more information was obtained on the physical and chemical properties of the element. Thereafter, research on vanadium has dealt largely with its use as an alloying element in steel and nonferrous metals. Vanadium is a widely distributed element in the earth's crust. It is more abundant than many metals but is disseminated in small quantities throughout a great variety of rocks. Relatively few deposits have contained ore of a grade suitable to warrant development for vanadium alone. It is produced in conjunction with uranium, iron, titanium, aluminum, and lead-zinc ores.

Jan 1, 1961

By David A. Summers

Coal is increasingly viewed as one of the major fuel resources of this country for the remainder of this century. The need to extract a greater percentage of the coal in a given seam, together with advantages of improved safety, indicates that longwall mining will become more widely used within this time frame. A novel method of mining coal on a longwall face, utilizing high pressure water jets, is herein described. The mining machine proposed will exploit the stress conditions which exist on a longwall panel in order to achieve the required productivity while at the same time reducing respirable dust and methane ignition hazards. The water jets will excavate only the boundary of the extracted seam section, and thus the energy requirement of the machine will be minimized. The action of the machine is similar to that of an existing coal plow, except in that the wedge teeth of the plow are replaced by oscillating high pressure water jets. The machine can, therefore, cut to the depth and at the speed of existing shearer units at equivalent power levels. The removal of impact stresses from the machine will reduce downtime required for maintenance and replacement of picks and lower the load on the haulage motor of the system. The ability of the machine to increase the depth of cut without an increase in horsepower will further improve productivity when transportation systems to remove the greater production are in operation.

Jan 1, 1974

By Richard C. Barth

Fourteen field plots were established at active coal mines in the Northern Great Plains. A wedge was cut into spoil and backfilled with soil; soil depth ranged from 0 to 152 cm over a linear distance of 15 m. Perennial grasses were planted in each plot, and production was measured from 1978 to 1981. Based on spoil traits and biomass response patterns, plots were grouped into four types. Spoil for Type I plots was near neutral, slightly saline, nonsodic, and clay loam in texture. Perennial grasses reached maximum production with approximately 50 cm of soil depth. Spoil for Type II plots was characterized as sodic and fine textured; soil-depth requirements averaged 83 cm for maximum production. Spoil for Type III plots was characterized as strongly acid, and production increased throughout the soil depth range tested. Spoil for Type IV plots was similar to soil in chemical and physical traits; there was no production response to soil depth. Soil depth requirements were also dependent upon precipitation and species. In general, soil-depth requirements decreased in dry years and with use of introduced species. An appendix contains data evaluations on an individual plot basis.

Jan 1, 1982