Search Documents

By Eric E. Cather

A mineral survey of the Fisher Gulch RARE II area (A5299), Trinity County, California was conducted by the U.S. Bureau of Mines and U.S. Geological Survey. The Bureau of Mines was responsible for detailed examination of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. The area is underlain by the Salmon Hornblende Schist. Tonalite stocks 1.5 mi (2.8 km) to the east and northeast of the area intrude the schist and are closely associated with the nearby nines (Cox, 1967). The mines have quartz veins containing sulfides and gold in shears trending east to north past in the schist and tonalite (Hotz, 1972). Strewn and terrace gravel s occupy most of the drainages, many have yielded substantial quantities of gold.

Jan 1, 1981

By J. V. Batty

Radioisotopes of selenium (se78) and tellurium (Te123) were successfully employed by the Bureau of Mines as tracers in metallurgical research directed to developing improved methods for volatilizing these elements from low-tenor raw materials. Prior research, guided and controlled by conventional analytical methods, was seriously hampered by inconsistent selenium and tellurium analyses, by the slowness of the conventional chemical methods, and by the poor accountability of these volatile elements in test products. Methods were devised and evaluated for admixing the radioactive tracer with typical raw materials and then following the deportment of the selenium and tellurium by radiometric methods with occasional chemical analysis checks. These techniques were found unusually effective in (1) quantifying the completeness and the rate of volatilization of selenium and tellurium while heating the raw materials at different rates to different temperatures and (2) accurately tracing and quantifying the distribution of minute amounts of these volatile elements in the several products made by high-temperature treatment and in the several units comprising the experimental equipment.

Jan 1, 1962

By Fred N. Kissell

In This Chapter [The explosibility of methane gas mixtures Effect of pressure and temperature on explosibility Less common sources of methane ignitions The amount of methane stored in coal Forecasting the methane emission rate Layering of methane at the mine roof When the recirculation of mine air is hazardous The importance of higher air velocity in preventing methane explosions and Mine explosions, barometric pressure, and the seasonal trend in explosions] Dealing with methane in mines and tunnels requires knowledge of the circumstances under which dangerous accumulations of methane are likely to occur. This knowledge involves the properties of the gas itself, an awareness of where these accumulations are likely to occur, and facts on how methane mixes safely into the mine air. The other chapters in this handbook address the handling of methane under a variety of specific circumstances, such as at continuous miner faces or coal storage silos. This chapter addresses some broad concepts that serve as a foundation for the suggestions provided in other chapters. THE EXPLOSIBILITY OF METHANE GAS MIXTURES Methane entering a mine or tunnel often enters as a localized source at high concentration. Figure 1–1 depicts a cloud of methane being diluted into a moving air stream. In this illustration, methane enters the mine from a crack in the roof. As the methane emerges from the crack, it progressively mixes with the ventilation air and is diluted. In the event that this progressive dilution reduces the concentration from 100% to 1%,2 as shown in Figure 1–1, the methane passes through a concentration range of 15% to 5%, known as the explosive range. In the explosive range, the mixture may be ignited. Above 15%, called the upper explosive limit (UEL), methane-air mixtures are not explosive, but will become explosive when mixed with more air.

Jan 6, 2006

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

Research by the National Institute for Occupational Safety and Health (NIOSH) on multiple-seam mining has resulted in two new ground control products. Information Circular (IC) 9495 In some U.S. coalfields, particularly in central Appalachia and the West, most mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously threaten the safety of miners and disrupt mining operations. Information Circular (IC) 9495 is a proceedings document containing a variety of papers that summarize recent knowledge about multiple-seam mining. A NIOSH study that analyzed case histories collected from 44 U.S. coal mines is described in detail. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. The study's results were the basis for the Analysis of Multiple-Seam Stability (AMSS) software package. The proceedings also contain two papers describing the LaModel family of software. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D implements a simplified, two-dimensional model suitable for quick approximations of the multiple-seam stresses and strains. Three papers in the proceedings focus on case histories. One describes the extensive multiple-seam experience at the Harris No. 1 Mine in West Virginia, a second contains examples of "extreme" multiple-seam mining from the central Appalachian coalfields, and a third describes interactions with regard to longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining. [ ] AMSS Software Package NIOSH has developed a simple, user-friendly computer program called Analysis of Multiple-Seam Stability (AMSS). AMSS can help mine planners to evaluate each potential multiple-seam interaction and take steps to reduce the risk of ground control failure. AMSS begins by evaluating the pillar design. It first calculates the single-seam pillar stability factor (SF)

Jan 11, 2007

By J. Walden, J. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers, mounted in suspension components, can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a global positioning system (GPS) is recorded at the same time as shock pressures or acceleration data, the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck. This research is part of a National Institute for Occupational Safety and Health (NIOSH) project called "Engineering controls for reduction of jolting/jarring injuries in surface mines." NIOSH is investigating how the work environment of haulage truck drivers can be improved. The US Mine Safety and Health Administration (MSHA) notes that, between 1986 and 1995, 60% of the back injuries were to haulage truck drivers in metal/nonmetal surface mining. Personnel from Phelps Dodge suggested that combining acceleration data with information obtained from a GPS could generate results with a variety of uses. Therefore, researchers at the Spokane Research Laboratory (SRL) began investigating how to tie acceleration and GPS data together. It was originally thought that this tool would be used primarily for road and truck maintenance. However, as research progressed, it became apparent that it would also be useful in providing feedback about equipment operations and identifying unusual causes of jolting. Experimental approach Available components that function well by themselves were linked for the purpose of proof of concept. Using a Modular Mining Systems (MMS) product called Vital Signs, SRL researchers took an Aero-Marine Products (AMP) acceleration recorder and hardwired it to MMS Dispatch equipment already installed on a truck. AMP is one of several manufacturers of acceleration recorders frequently used to monitor freight during shipping. MMS Dispatch is used for production accounting and truck dispatching and uses GPS tracking. Through Vital Signs, an analog or digital alarm signal can be recorded. Steve Rhoades, of MMS, wrote unique code that links the Vitals Signs data and GPS location and stores this data in an ASCII log file. SRL researchers installed the equipment in a Caterpillar 793 haul truck. The result was a working prototype. Figures 1 and 2 show the instrument installation in the truck. Discussion From 8:30 pm on Sept. 14, 1998 until 6:50 am on Sept. 15 1998, 899 jolts above a threshold of 2 g (1 g is the acceleration of gravity. It is either 9.81 m/s2 or 32.17 ft/ s2.) were measured on the test truck. Some sections of the haulage road produced most of the events, while

By R. H. Grau, R. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing somepractical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers’ exposure to airborne contaminants.

Although the mining industry has achieved record-low fatalities and injuries for each of the last three years, there are still too many miners injured or killed in this nation ís mining operations. Many mining injuries or deaths might have been prevented by using risk assessment to identify and control or eliminate the hazards associated with a task. To focus attention on the importance of conducting risk assessments in keeping mining workplaces safe and healthful, MSHA introduced this initiative on October 12, 2004. This initiative is called SLAM. SLAM is an acronym for Stop, Look, Analyze, and Manage. The steps involved in SLAM are: Stop ñ stop and consider the work involved Look ñ look for and identify the hazards Analyze ñ analyze what needs to be done Manage ñ manage safety by developing and implementing controls Everyone should be aware of the risks of an accident before beginning a task. It may not always be obvious that performing a seemingly routine task could result in an accident. That is why conducting a risk assessment is so important. Itís important to remember that over time a mining workplace seldom remains unchanged. Risks must be assessed whenever procedures or processes change, whenever new tasks are started, or non-routine tasks are performed.

Jan 1, 2005

By Gerald T. Homce

Data from the U.S. Bureau of Labor Statistics show that 89 water well drillers died on the job between 1992 and 2002, and 28 of these deaths were electrocutions (Figure 1). In fact, elec­trical accidents are the leading on-the-job killer of water well drillers. The use of electricity is such an integral part of our lives that we usually take it for granted, but if we don?t understand or choose to ignore the hazards associated with electricity, the results can be deadly. Why is electrical shock so dangerous? If the voltage (of a shock) is sufficient to drive electrical current through your body, just 10 milliamps of cur­rent (1000 milliamps = 1 amp) can cause muscles to contract and prevent you from releasing an energized wire or tool in your grip. As little as 30 milliamps of current can paralyze your breathing, and 75 milli­amps can cause your heart to stop pumping blood (ventricular fibrillation). As a comparison, a small bedroom night-light draws about 30 to 60 milliamps. Other factors influence how severely you?ll be shocked if you touch a live electrical circuit, such as the path electrical current takes through your body and how long it flows, as well as your body weight. How much voltage is needed to drive electrical cur­rent through your body? Not much! Generally, any power source at 50 volts AC or higher is considered dangerous.

Jan 1, 2008

By Forrest T. Moyer

Quarry accidents in 1963 caused 61 fatal and 3,468 nonfatal injuries which occurred at respective frequency rates of 0.31 and 17.91 per million man-hours of worktime. The fatality record in 1963 was better than in 1962 but was appreciably worse than in 1.961. For nonfatal injuries, the 1963 record was slightly worse than in 1962 but was better than in 1961. The injury--severity rate of 2,913 days lost or charged per million man-hours in 1963 was better than that of 3,046 in 1962, the first year for which such data became available. The average severity of all injuries in 1963 was 160 days lost or charged per injury, 15 less than in 1962. An average of 91,960 men were at work on active days in 1963 and these men had an aggregate worktime of 193.7 million man-hours during the year.

Jan 1, 1972

By Russell A. Schreiner

In conjunction with the Geological Survey, the Bureau of Mines conducted a mineral investigation in 1981 and 1982 of the Santa Rosa Mountains Wilderness Study Area (WSA), Riverside County, California. The Bureau of Mines is responsible for the mineral survey of mines, prospects, and mineralized areas in and near the WSA. A literature search was completed to obtain information concerning mineral occurrences and mining activity that relate to the WSA. A field investigation inside, and up to 1 mi outside, the boundary of the WSA, disclosed one prospect. This prospect was surveyed by compass and tape, and five samples were taken to determine the representative mineral content. No attempt was made to expose concealed mineralization or to re-open caved workings. All five samples were analyzed by fire assay for gold and silver and by colorimetric methods for tungsten. Two of the samples were analyzed by semi quantitative spectrographic methods to determine if any unsuspected elements were present. All analyses are furnished in this report except for the semi-quantitative spectrograhic analyses. Complete sample analyses are available for public inspection at the Bureau of Mines, Intermountain Field Operations Center, Building 20, Denver Federal Center, Denver, CO 80225.

Jan 1, 1983

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60 percent and 40 percent, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert, and a rigid insert for cleaning the roof bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the coveralls when using either of the inserts.

Continuously monitor and record respirable dust levels underground by a reliable, sensitive, and fast-response device. Approach A light-scattering photometer, having a LED (Light Emitting Diode) light source and other significant improvements, has been designed and incorporated into a portable continuous monitor. How It Works The monitor continuously draws air into the sampling inlet through a cyclone that removes dust particles larger than respirable size. The dusty air enters the photometer vertically downward through a cylinder which is intersected by the optical system. (This cylinder appears as a circle in the drawing of the photometer.) The center of he column of dusty air intersects a beam of pulsing light from the LED, causing some of the light to be reflected, scattered, and refracted. Only the light that is scattered at an angle of about 700 from the light beam passes through a lens to the photodetector which generates an output voltage Signal proportional to the dust content in the air. This signal is detected, amplified, and converted to a digital readout directly in milligrams of dust per

Jan 1, 1979

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By M. J. Senk, A. Lusin

Federal regulations require that methane liberated at the face be diluted and removed to maintain methane gas concentrations below 1 pct (CFR) in working places and intake air courses. The delivery and distribution of intake air at the face is critical for effective face ventilation. Improved techniques for monitoring the movement of intake air to the face are needed. A test system was developed and a computer program written for using a three-axis ultrasonic anemometer to measure airflow in a simulated mine entry. Results of tests conducted in the entry showed that the anemometer is a valuable tool for measuring mine airflow conditions near the face.

By Steven J. Page

Researchers have developed a model to describe airborne respirable dust (ARD) generation on surface coal mine drills. By measuring a few basic parameters and using a graph, a drill operator or engi­neer can estimate the relative severity of drill dust emissions as well as how much of a reduction in ARD can be obtained by changing any given parameter. Geometric parameters include: drill deck cross-sectional area, shroud leakage associated with the deck shroud as well as the operational parameters of bailing air­flow, and dust collector airflow. The rela­tionships yield predictive ARD values which fall in the range measured on oper­ating drills for collector/bailing air flow ratios greater than 2. Overexposure to airborne respirable crystalline silica dust can cause serious or fatal respiratory disease. Exposures of sur­face coal mine rock drillers to respirable crystalline silica are of particular concern. In a 1992 alert on silicosis in rock drillers, the National Institute for Occupational Safety and Health (NIOSH) reported on 23 cases of advanced silicosis (acute, acceler­ated, and chronic) ranging in ages from 25 to 60 with drilling tenures ranging between three and 20 years.1 Most of the cases involved drill operators in their 30?s and 40?s, indicating high silica exposure levels are associated with their occupation. A more recent lung x-ray surveillance study of a 664 volunteer population of surface coal miners showed that the prevalence of silicosis-like abnormalities was 9%.2 The two most significant factors associated with these abnormalities were increasing age and years of drilling experience.

Jan 1, 2008

By A. F. Robertson

"INTRODUCTION This report is supplemental to R.I. 4178 and deals with the work accomplished between June 15, 1945, and September 7, 1945, on the Mitchell-Hodge mine, Grady mine, Albea and York property, and Cuzzort property.ACKNOWLEDGMENTSIn its program or exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigcal Branch, O. C. Ralston, chief, analyzes samples and performs benefication tests.Acknowledgment is due Mitchell H. Kline, chief, Raleigh Division, Mining Branch; Abraham L. Fox, acting chief, Raleigh Division, Metallurgical Branch; and Rowe McCrae, district engineers, U.S. Bureau of Mines, Gainesville,"

Jan 1, 1946

By L. C. IlsLey

The increasing use of Diesel engines for operating equipment on trunk-line railroads and for power-plant units has stimulated interest in the use of Diesel engines for other lines of work, among which is the possibility of substituting Diesel locomotives for trolley locomotives for mines. The possibility of developing Diesel locomotives for duty in American mines is not as remote as it might seem, particularly in view of the fact that locomotives of this type are already used in considerable numbers in European mines. A study of Diesel locomotives in Europe is contained in Report of Investigations 3320, Diesel Mine Locomotives - Development and Use in European Coal Mines, by George S. Rice and F. E. Harris.

Jan 1, 1938

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of canopy air curtain devices under Bureau of Mines Contract H0232067. The canopy air curtain device is designed to reduce the level of respirable dust exposure to a continuous mining machine operator while having a minimum effect on operator safety, mobility and comfort and being compatible with mining equipment. This contract was devoted to the development of a device which utilizes an invisible curtain of air to envelope a mining machine operator's breathing zone with filtered air to provide respiratory protection. Various concepts were evaluated by means of laboratory tests. One concept was selected and was tested on various mining machines at underground sites by means of MSA personal samplers. The canopy air curtain was found to be effective. The percent reductions over the ambient dust concentrations were about 30 to 75 percent depending on the amount of time the operator spent under the air curtain. At one test site, the device enabled the mining machine to operate within compliance. Donaldson Company is presently working on the commercial production of the device.

Jan 1, 1975