Search Documents

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

Prepare ATF Report of Theft or Loss (ATF Form 5400.5). A Report of Theft or Loss - Explosives Materials must be prepared when it is discovered that explosive materials are missing from inventory. Submit the original to the U.S. Bomb Data Center and keep a copy for your records. The form can be obtained from the ATF Distribution Center or from www.atf.gov. Although the U.S. Bomb Data Center should be notified as soon as possible, Federal law requires notification within 24 hours of the discovery. A full inventory check is also highly recommended (but not required) to locate missing explosives and to prevent future losses.

Jan 1, 2008

By J Lyall Workman, Peter N. Calder

"Presplitting is a technique mines and quarries may use to produce high quality final pitwalls. Damage from backbreak can be minimized, thereby insuring the final pit walls standat the designed angle. Thus costly excess waste removal is avoided. Safety in the pit isenhanced. Control blasting is an essential component of procedures to maintain the stabilityof final pit walls prone to failure."

Jan 1, 1993

By E. Contestabile, B. von Rosen, P. Lightfoot

As part of an accident investigation ANFO was subjected to various abusive tests. A tractor-trailer carrying 18,000 kg of blasting explosives, caught fire, burned for approximately 30 minutes, and then detonated. A series of tests was designed to observe the behaviour of ANFO when subjected to different thermal stimulus tests and more specifically, the Height-to-Detonation Test. Three diameters of steel pipes were used in the Height-to-Detonation Tests thereby simulating cylindrical columns within a pile of ANFO. The ANFO samples were then subjected to various thermal stimuli to initiate a reaction. Through the use of some instrumentation, the response of large ANFO samples was recorded and its behaviour, including the occurrence of phase changes will be analysed.

Jan 1, 2001

By Alton Dunaway, Kevin Sullivan, Charles Gray, Doug Hall, Kevin Grant, Kelly Thiel, John Paulson, Bruce Leland, Cole Boyd

Beaver (Castor canadensis) are responsible for economic losses exceeding $4 billion over the last 4 decades in the southeastern United States alone. A large portion of these damages occurs to public roads and highways, forests, agricultural resources, and other property from flooding caused by beaver dams. The United States Department of agriculture, Animal Plant Health Inspection Service, Wildlife Services (WS) program is a non-regulatory Federal program directed by Congress to assist resource owners with managing damage caused by wildlife.

Jan 1, 2007

By Evan Jannoulakis, Wilfrid Comeau

Using the Scaled Distance (SD) and the vector sum Peak Particle Velocity (PPVvs) from a single delay, preferably single blasthole, in a shot, a number is derived which has shown itself to be consistently related to blasting efficiency, as experienced by one of the authors of this paper over the last thirty years. The numbers derived by this process range in value over one order of magnitude more or less. This variation, a function of distance, weight of explosive in the delay, blasthole diameter, blast design, powder factor and the geological environment, can be consistently related to two of these factors, powder factor and distance. In actual use the measured "BED" representing good blasting results should not vary by more than + 33 to + 50 percent of the estimated "BED" in non calibrated cases, and + 10 to 20 percent where previous experience is available. Relatively high "BED" values are indicative of poor blasting results while relatively low "BED" values may be precursors of poor blasting results in a shot. There are many variables in the geological environment which can affect the "BED". A case study is presented from a surface coal mining operation in eastern Canada. This case study tries to evaluate the reasons for the variability in "BED" values derived from multi-hole shots. A problem in using "Signature Vibrations" from a single-hole shot to predict blasting vibrations from multiple-hole production shots is identified.

Jan 1, 1998

By Gordon C. Petersen, Gary A. Almeraris

This paper describes the controlled blasting techniques required to mine a rock tunnel section of a main interceptor located in the Boston Metropolitan area. The 3m (10 ft) x 2.8m (9.25 ft) horseshoe shaped tunnel was driven 490m (1600 ft) by conventional drill and blast methods. The geology varied round by round and consisted of five highly faulted and jointed igneous rock types. The tunnel intersected numerous slickenslides and open mud seams which hampered both drilling and loading operations. Smooth blasting wee critical in order to keep overbreak tc a minimum in this extremely hard but blocky ground.

Jan 1, 1991

By Langdon T. Mitchell, Karl Ingmarsson

The title is not referring to jewelry; nor is it about diamond core drilling. This article is instead about an emerging application for diamonds, hard rock percussive drilling with diamond drill bits. Diamond’s outstanding wear resistance has long been taken advantage of in core drilling. However, until now diamond has been less successful in hard rock production drilling in the mining and quarry industry.

Jan 1, 1999

By Josh Calnan, Paul M. Holmgren, Abigail N. Styer

Detonating cord is a staple of the explosives industry, used widely in the civil and defense industries. Detonating cord is a thin, flexible plastic tube filled with pentaerythritol tetranitrate (PETN). It has many applications in mining, construction and military disciplines. For civil applications, it is used to connect and initiate a series of blastholes in a desired pattern. In the defense sector, it can be used as a detonating agent, a priming agent or alone as an explosive charge. Research has been done to understand the initiation and detonation physics on the detonating cord. However, its sympathetic detonation characteristics needed to be further analyzed.

Feb 1, 2020

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023

By Tony Francelj, D. Scott Scovira, Remi Proulx

The Meikle Mine is a high-grade, underground gold mine that utilizes a primary and secondary stoping method with delayed backfill. The newly developed Rodeo Mine will start production using similar mining methods in late 2001. The combined production for the mines will be 4100 stpd of ore in 2002. Dilution of the secondary stopes resulting from blast induced overbreak of the backfill placed in the primary stopes was an issue identified as being a major contributor to the total mining cost at the Meikle Mine. To address the overbreak issue, a low-density, polystyrene enhanced bulk emulsion was developed and introduced to the mine. The density and energy of the emulsion was varied until an optimal level was reached. The use of a low-density bulk emulsion has greatly reduced the overbreak of the primary stope backfill when blasting the secondary stopes. Benefits to the mines include reduced secondary stope dilution, lowered total mining cost, and increased revenues.1

Jan 1, 2002

By Adrian Moore, Dominic Hooton, Alan Richards

Significant factors affecting airblast overpressure (AOP) emissions include charge mass per delay, distance from the blast site, burden, stemming height, and delay timing, topographic shielding, and meteorology. The effect of charge mass on the frequency of the airblast produced, and the delay timing required to control the level of airblast overpressure is explained by two case history examples which were not affected by topographical shielding and meteorology. One is a cast blast with a charge mass per hole of 1000 kg (2200 lb), and the other is a quarry blast with a charge mass per hole of 64 kg (141 lb), These examples show that the delay interval necessary to prevent an increase in AOP levels must be increased with an increase in charge mass per hole. The effect of a ‘soft-start’ technique where a reduction in AOP levels is achieved by decking only the initial front-row holes is also illustrated.

Jan 21, 2025

By C. Heiss, A. Hofmann

Due to an explosion in an Austrian steel works during the basic oxygen process, the Chair of Mining Engineering and Mineral Economics at the Montanuniversitaet Leoben was assigned with the set-up of a test arrangement to study the effects of large-scale particle emissions on the plant´s installations and the testing of various structures and structure-combinations to be applied as explosive-proof enclosure.

Jan 1, 2012

By Braden Lusk

The problem of predicting damage in densely developed areas due to incidental or malicious explosions is one of considerable importance to local, state, and federal governmental bodies. The difficulty of making such a prediction is confounded by the urban canyon phenomenon as the shock wave intensifies or rarefies depending upon the particular arrangement of buildings. The specific method detailed herein used a Computational Fluid Dynamics solver, ANSYS AUTODYN, to operate on Geographic Information Systems data, ArcGIS, which captured the geospatial relationship between the various buildings in downtown Oklahoma City, prior to the Murrah Building bombing. The model of Oklahoma City was first developed using the building footprints and elevations provided by the ArcGIS database. Due to the sheer size of the problem, the model was then subdivided into annular zones of increasing distance from the center of the blast. Each subsection was then solved using an Euler model in a cascading fashion with the output of the preceding model forming the input of the present model. To further reduce computational time, the size of the Euler nodes was increased at each stage as the section area increased. Due to the loss of precision in capturing peak pressure values when using larger size nodes, it was necessary to perform a transformation on the results using one dimensional wedge calculations with higher precision. The Murrah Building bombing event was an excellent case study due to its available ArcGIS data and the level of documentation of damage to surrounding structures due to the blast. The results from the staged CFD calculation were then used to develop a damage potential contour map. The documented incidents of damage in the area surrounding the Murrah building were then compared to the model generated damage potential contour map. Copyright ©

Jan 1, 2010

By Mark Bosse

This is a paper demonstrating the use of a fixed wire and trolley system to deliver 2 or 5 lb cast primers (with 2 meter cap/fuse assemblies) deep into avalanche terrain. This avalanche terrain is mitigated using explosives prior to being opened to guests.

Feb 1, 2020

By R. Ticona, J. Alarcon

In the continuous search to provide comprehensive solutions and identify opportunities to improve ore traceability, from the blastholes to mill feed, different ore traceability systems have been developed, which allow tracking the ore and associating its geometallurgical characterization of different sectors of interest from blasting to the processing plant, facilitating decision making and operational actions when detected during each stage of the plant. With the objective of improving the ore tracking from the mine to the processing plant in a Peruvian copper mine operation, the impact on the processing plant was evaluated in relation to blasting optimizations through a tracker system, relating the processes performance of the whole production chain with the geotechnical and geometallurgical properties ores in real time in the process plant: detecting when it was feed waste, high grade ore, low grade ore and ore with arsenic, among others. Unit and integral tests were carried out over a period of three months, with an implementation of tracker detection portals in the processing plant, which allowed to verify the proper communication of data and the web platform. The tests were focused on several blasts where the ore was in contact with waste and it were directly sent to the plant, with a classification by type of grade (high, medium, and low grade), type of material (ore-waste contour), this stage allowed to make operational adjustments in the field and in the mining operation. Finally, in the economic results, the special tests had 1000 trackers, obtaining for this project a sensitization of a cost benefit for the test stage, for the reduction of 50% of the waste material feed has crushed, with an estimated benefit of 1,987,646 USD.

Jan 1, 2024

By R L. Mayville

The author explains why the strategic location and important limestone reserves at Chattanooga Quarry led to a decision to extend operating life by continued benching down to lower levels. He discusses the steps taken to accomplish this objective. These include relocation of the primary crusher from the second level to the fourth level, pre-testing of explosives designs and powder factors, control of a substantial water problem, and computer monitoring of stone production costs.

Jan 1, 1984

By Aris Tambunan, Nella Lubis, Nurafrianti Saala, Komang Widhiayanto, Herry Saputra, Rudolf Sitorus

Maximizing mining recovery rates and minimizing ore loss are pivotal objectives for economic efficiency and operational effectiveness. This study explores methods to address these imperatives by enhancing ore production and recovery through improved blasting techniques and spillage control in the Martabe Gold Mine Project in North Sumatra Province, Indonesia. Between 2018 and 2021, the average mining recovery rate stood at 93%, resulting in a potential annual ore loss of 7% and a potential quarterly financial impact of close to $2 million. Maintaining and enhancing mining recovery became crucial, with a planned 30% increase in total material movement for 2022. The mining recovery target for 2022 was set at 96% based on best achievement historical data from 2021 to increase ore tonnage by 203 KTon per annum. To achieve the primary objective of increasing ore production by improving mining recovery, the study focused on predicting and controlling the movement of blasted ore to reduce spillage and enhancing the grade control model to reflect actual conditions post-blasting. Several alternative solutions were explored, primarily emphasizing drilling and blasting activities. Essential methods included capturing the actual blasting movement to adjust the ore block based on blasting design data and post-blasting muckpile topography. This approach minimizes ore loss by providing output as ore block adjustment based on post-blast movement data. In addition, the tie-up design was adjusted to control ore spillage outside the pit ridge. The implementation of these methods yielded significant improvements. Adjusting the ore block based on actual blasting movement contributed $1,545,764 in benefits. Controlling ore spillage outside the pit ridge achieved a 10% reduction in spillage, contributing $79,184 in benefits. These enhancements successfully met the 2022 mining recovery target of 96%, marking a 3% increase from 2021. Consequently, ore loss was reduced by 178 KTon throughout 2022, resulting in a financial impact of $7.3 million. The study underscores the significance of precise blasting techniques and effective spillage control in enhancing mining recovery rates.

Jan 21, 2025

By Braden Lusk

A typical rural house surrounded by a surface coal mine was instrumented in 2008. Information regarding ground vibration, airblast, and sounds inside the house was collected. Previous publications have included conclusions about this data with regard to blasting source (far-field or near-field) and results as to how the residents experience the blast were made. Several events were also recorded that were not related to blasting due to the nature of the trigger system. The trigger of the monitoring system was attached to one of the mid walls of the house, thus other normal daily events produced vibration levels significant enough to trigger the monitoring system.

Jan 1, 2011

By Gary Cavanough

The spontaneous exothermic reaction of ammonium nitrate explosives with sulphide-containing rocks, commonly referred to as reactive ground, is a site-specific condition that can lead to spontaneous detonations. Mine sites typically carry out regular assessment of ground for reactivity. In Australia, reactive ground testing is conducted according to the Australasian Explosives Industry Safety Group (AEISG) Code of Practice. This paper presents a new method to assess reactive ground. The new method can be completed on the mine site or in the laboratory. The new method allows samples to be tested in hours not weeks, as required when using the method prescribed in the AEISG Code of Practice. The new method also provides an explanation of why ground is reactive or not reactive, Whereas the AEISG Code of Practice provides a reactive, not reactive or marginal results with no understanding of reason for these results. Case studies on the use of weathering agents, pH, sulphide content and carbonate content will be reported. These case studies identify instances where the testing as per the AEISG Code of Practice provides false positive and false negative results. A false positive result will require the use of inhibited products when they are not actually required which increases costs and reduces productivity due to the need to used multiple explosive products. A false negative result increases the risk of an unplanned initiation of a blast hole.

Feb 6, 2023