Search Documents

By Duane Skidmore, Francis Otuonye, Calvin J. Konya

Proper stemming not only affects the rock breakage process, but also controls the unwanted side effects of blasting such as airblast, ground vibration, and flyrock. Little research has been conducted on the behavior of borehole stemming material under high pressure loading conditions. The methods of selecting stemming particle size and necessary stemming length were previously determined only by trial and error in the field.

Jan 1, 1982

By Jody Todd, Ernesto Villaescusa, Ronald Lachenicht, Kelly Fleetwood

In the underground environment, characterisation of a rock mass during the mining cycle becomes increasingly difficult due to a lack of rock mass exposure for measurement or observation. In most cases rock mass characterisation occurs prior to mining by inspection and logging of exploration drill core, or prior to mass excavation through drive mapping for geological and geotechnical data. Characterisation strategies, if applied during the mining cycle, can reveal near-field anisotropies that may affect the behaviour of the rock mass with respect to excavation. These methods can aid in understanding the performance of stopes based on geometry, in-stope extraction sequence, and stress modelling. One such method of characterisation involves the use of production blast vibration monitoring and analysis as indicators of rock mass anisotropy through travel-time tomography.

Jan 1, 2008

By C. Yi, D. Johansson, C. San Miguel, M. Wimmer

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Production blasting has significant impact on the efficiency and productivity of SLC output, affecting material fragmentation, flow and recovery. Misfires could occur during blasting in SLC, which results in the loss of explosives and poor fragmentation. Usually, the blastholes are top-initiated with redundant lower primers set at + 25 ms as a precaution. If the top primers fail, the lower primers may initiate the explosive, which will induce out-of-sequence delays that can influence fragmentation and gravity flow. This work investigated the impact of misfires and out-ofsequence delays on fragmentation and gravity flow through numerical simulations using a coupled finite element and discrete element method. Different scenarios of misfires and out-of-sequence delays were studied, and the fragment size distribution was obtained to evaluate the blasting performance. The material flow behaviour was investigated to assess the gravity flow process. The results indicated that misfires significantly affect the fragmentation and the gravity flow process while the effects of out-of-sequence delays are not so significant for the investigated cases

Jan 1, 2024

By Brent Blanchard

As most veterans of our industry are aware, explosive demolition by its very nature is often a challenging proposition. Even under the best of circumstances, proper planning and care must be taken during a variety of processes to ensure a safe, successful result. However, every now and then a project suddenly arises where safety, timing and cost factors combine to form a critical scenario requiring rapid execution in an environment far more challenging than the norm. On these occasions, the stresses, complications - and most notably the dangers - related to the industry increase exponentially, and conspire to test the mettle of even the most seasoned experts.

Jan 1, 2003

By Cameron McKenzie, John Heilig, Patrick Andrieux, Andree Drolet

It is widely accepted that both underground and surface blasting operations can de-stabilise excavations to the point where it can threaten the feasibility of mining through personnel safety or OK dilution. Research has been undertaken to outline a practical method in which the impact of blasting will be accounted for during the early excavation design stage by modelling, and during the following production stages by monitoring rock response to blasting operations.

Jan 1, 1994

By Milton Barbosa Landim, Denise de La Corte Bacci

Statistical methods of multiple regression analysis, trend surface analysis and principal components analysis were applied to seismographic data recorded during production blasting at a diabase quarry in the urban area of Campinas (SP), Brazil. The purpose of these analyses was to determine the influence of the following variables: distance @), charge weight per delay (W), and scaled distance (SD) associated with properties of the rock body (orientation, frequency and angle of geological discontinuities; depth of bedrock and thickness of the soil overburden) in the variation of the peak particle velocity (PPV). This approach yielded variables with larger influences (loads) on the variation of ground vibration, as well as behavior and space tendency of this variation. The results showed a better relationship between PPV and D, with D being the most important factor in the attenuation of the ground vibrations. The geological joints and the depth to bedrock have a larger influence than the explosive charges in the variation of the vibration levels, but frequencies appear to be more influenced by the amount of soil overburden.

Jan 1, 2002

By Robert Hopler

RBH Note: in 1913 black powder was still dominant as a coal-mining explosive, but permissible explosives were making some slight headway. For example, in 1902 there were only 11,300 pounds of permissibles used in coal mining, but in 1913 the quantity was 21,801,285 pounds. However, there were 187,551,653 pounds of black powder used that year. It took many years before the use of black powder ended in coal mining. From the picture of the miner reparing his explosives it’s hard to tell what he’s using, but the fact that a wooden Du Pont powder box is shown, he’s probably not using black powder. That doesn’t mean he’s using a permissible, either, since that was not yet a requirement. It’s interesting that the miners have open flame cap lamps, and the miner is actually smoking a pipe while preparing his explosives.

Jan 1, 2014

By John Floyd, Maria Rocha, Benjamin Cebrian

Wall control blasting is needed in most metal mining operations in terms of increasing mineral reserves and assuring the safety of the operation. This type of blasting has the goal to achieve a clean, stable rock wall in the shortest distance from a well fragmented, easy to excavate, blasted rock mass. This can be done with a variety of blasting techniques, all of which decrease the explosive energy towards the final wall. Each technique needs to suit the geology: modified production blasting, buffer blasting, pre-split and line drilling of empty holes. Pre-split is the most expensive technique, and allows final steeper bench face angles while modified production blasting is the least expensive but needs wider berms.

Jan 1, 2018

By Keith Henderson

An open pit quarry operation in West Central Illinois provided a challenging proposition regarding the removal of a rock wall that once separated two pits, but was now in the middle of the north wall of the combined pit. Their mining plan included the development of a new ramp into the quarry pit in order to lessen the slope and to shorten haul truck cycle time. The task would be to remove a section of rock left behind from mining operations more than 20 years ago that was at or near the bottom of the designed ramp.

Jan 1, 2012

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By William Reisz

The explosives and blasting industry has a commendable safety and security record, especially over the last several decades. This is due in large part to our newer technologies, better training and education, engineering practices, corporate initiatives, our professional organizations, and whether we like to admit it or not - our regulatory agencies.

Jan 1, 2012

By Yong Pan, Purushotham Tukkaraja

It has been well understood that blasting is the cost-effective method for breaking rocks as compared with the mechanical systems. However, vibrations induced by blasting in open-pit mines could pose problems to the structures surrounding the mine site. Blast-induced ground vibration has been the subject of research for several studies in the past; because of the complex nature of blasting mechanism, it is difficult to predict blast-induced vibrations. Even though there are several approaches proposed by the previous researchers, traditional regression analysis is still playing an important role in predicting blast-inducedgroundvibrations.

Jan 1, 2019

By Kwang-Yeom Kim, Dong-Gyou Kim, Hyo-Kwan Yoon

This study was intended to simulate the blasting model using notched-hole with numerical approach. Numerical analysis approach was applied to compare and evaluate the blasting model using notched-hole and circular hole. To implement non-linear dynamic blasting model, blasting analysis was carried out with AUTODYN code. Behavior of two models was compared and evaluated using AUTODYN and visual analysis and quantitative evaluation based on pressure and stress to verify the effect to induce the destruction territory to the specific direction when blasting with notched hole was attempted.

Jan 1, 2010

By David E. Siskind

In the early 1980's, the Bureau of Mines published four reports of structural response and damage from surface mine blasting, vibration monitoring, and analysis methods. These findings replaced simpler and less restrictive Bureau criteria dating back to 1962 for ground vibration and 1943 for airblast.

Jan 1, 1991

By Kris Shukla

Noise and vibration produced by blasting generate curiosity and concern from neighbors. Experiments conducted in Sweden, Canada and U.S.A. have established that fine cracks in the plaster--the weakest part of building components--appear at a particle velocity of 4.0" per second or more. Taking into account the margin of safety, the safe zone criteria of 2.0" per second has been established.

Jan 1, 1978

By Klaus G. Hinzen

Seismic observations offer the only possibility for remote sensing of physical processes like shock-front spreading, material crushing and ground movement. A better understanding of these processes will help to increase the economy of blasting. We developed a digital seismic monitoring system for research purposes. The system can simultaneously record up to 64 channels with a maximum sampling rate of 31 kHz per channel. A software package for rigorous analysis of blast induced seismic waves has been developed.

Jan 1, 1989

By Doug Johnson

This paper reviews the field implementation of R & F Coal's blasting optimization work concerning analysis, prediction, and control of overburden blasting vibrations using site specific measurements and state-of-the-art computer technology. Blasting personnel at R & F Coal had the opportunity to work jointly with Otto Crenwelge of Shell Development Company in his test studies and to later be instructed in the procedures involved in optimizing vibration frequency.

Jan 1, 1988

By Michael Burrell

This project involved the protection of an historic landfill located on the site. Construction blasting was for a permanent access road to carry traffic to and from a new metal processing plant being constructed nearby. The landfill contained materials disposed of during the closure of a Phosphorus plant that had previously occupied a portion of this site.

Jan 1, 2012

By John L. Didlinger

We all hate the paper work in keeping accurate blasting records. Nevertheless, have you ever thought what those records could show you? Think about it. Those records could show you vibrations, noise, and safety problems. They could show you the ratio of powder used and tons produced, the cost per foot, even help negotiations for pricing.

Jan 1, 1997

By Donald Wagstaff, D. Scott Scovire

The Coeur Rochester Mine is the largest primary silver surface mine in North America. Throughout its 17-year life, gold and silver grades leaving the tertiary crusher have typically been, on average, slightly below the mined bench grades as determined by blast hole assays. On a project-to-date basis, this grade variance is well within industry standards. While these variances are acceptable, mine personnel continue to study ways to further minimize the grade differences. One suspected cause for lower than expected head grades are ore loss and dilution resulting from blast-induced shot movement. In regard to grade control, the underlying design principle for non-electric blasts is the generation of uniform movement of the blasted rock material. Using one or two uniform directions of initiation, ore control methods at Rochester currently include adjusting flag lines on the muckpile in an attempt to account for displacement from original, pre-blast locations. To improve upon standard non-electric blasting practices, a series of evaluation blasts using an electronic initiation system (Orica i-konTM) was conducted in the summer of 2002. The primary objective of the evaluation blasts was to design shots that would segregate the ore and waste blocks into distinct muckpiles. Due to surface delay burning front limitations, truly effective ore and waste segregation blasting is difficult to accomplish with non-electric initiation systems for all but the most basic of ore geometries. The electronic detonator evaluation blasts produced visible boundaries in post blast muckpiles, identified by troughs or low areas, that closely matched the actual locations of pre-blast ore control flag lines based on blast hole assays. By blasting the ore and waste into distinguishable piles that were flagged and excavated accordingly, it is believed that blast-induced ore loss and dilution was reduced.

Jan 1, 2004