Search Documents

By J A. Singer, S R. Iverson, C A. Link

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By C B. McCampbell, R W. Jr Bickes

Sandia National Laboratories has developed a semiconductor bridge (SCB) igniter for the ignition of a variety of explosive materials. When subjected to a low-energy current pulse, the bridge bursts into a plasma causing rapid ignition of the explosive material pressed against the bridge. Despite the low energies required for ignition, SCB components have proven to be explosively safe, meeting both no-fire and electrostatic discharge (ESD) safety requirements.

Jan 1, 1991

By Braden T. Lusk, Shannon P. Lusk, Kyle A. Perry

A high explosives shock tube has been constructed and developed to test blast resistant windows with pressure versus time waveforms similar to waveforms generated by arena testing. Calibration of the high explosives shock tube, or Large Arena Test Simulator (LATS), included numerous tests performed by detonating varying charge weights at different distances from three piezoelectric pressure sensors located at one end of the shock tube (where the test subject would be installed). The maximum reflected pressure and positive phase impulse were calculated for each waveform generated in the tests. Pressure versus distance and impulse versus distance graphs were generated. Results have been graphed in order to predict charge weights and distances that correlate to the desired pressure and impulse at the end of the tube for future tests. This is a valuable tool when testing expensive, job specific components so the loading requirements are met on the first attempt.

Jan 1, 2010

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on any standard PC.

Jan 1, 1997

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By Sanna Mustonen, Seppo Mellanen, Mellanen, Pekka Kantia

In Finland Posiva Oy (Company) is responsible for implementing the final disposal programme for spent nuclear fuel of its owners. Company is preparing for the geological disposal in Olkiluoto crystalline bedrock. Excavation will be executed using drill and blast method. Method unavoidably causes variable excavation damaged zone (EDZ) on tunnel surfaces. The EDZ constitutes a risk for long term safety and therefore good control methodology of the blasting technique is required. The thicker the EDZ, the greater is the likelihood for detrimental transport pathways for ground water to transport radio nuclides, should those be present.

Jan 1, 2016

By Erkan Bayrak, Serkan Erkara, Ozkan Duzgun, Ekin Gungor

This paper presents part of the outcomes of the drill and blast optimization project carried out at Kisladag Gold Mine in Turkey. Kisladag Gold Mine is the largest gold mine in Turkey with a low-grade, bulk-tonnage, open pit operation that uses heap leaching for gold recovery. After blasting, the ore is fed to a three-stage crushing circuit which prepares crushed ore approximately -10 mm (0.39 in) for heap leaching. Crusher downtime analysis showed that blocky material and insufficient feed are causing significant downtimes with the primary crusher. This was supported by the fragmentation data collected to date. It was decided to initiate a fragmentation project to understand the variation in the run-of-mine (ROM) size with a view to provide a consistent feed to the crushing circuit. The study includes the analyses of the ore strength and structure, image analysis of the fragmentation pictures acquired from blasts, blast auditing and quality assurance and quality control (QA/QC) analyses. During this project, over 200 fragmentation pictures were acquired from 47 blasts to optimize ore and waste blasts. Ore strength varies between 30 and 120 MPa and rock quality designation (RQD) ranges between 30 and 100. A site-specific fragmentation model was used to calibrate the fragmentation for blast domains formed. In addition, alternative cases were simulated to achieve blasts designs with consistent ROM fragmentation size distribution. Alternative blast designs that include stemming length and powder factor changes were suggested. Long stemming length, drill cuttings use, free faced blasts, small shot sizes and poor stemming length control were some of the key issues causing coarse fragmentation.

Jan 1, 2015

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

"Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape of an organization. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called 'landmarks'), how well they are aligned to support a particular type/nature of innovation in the organization (e.g. radical vs. incremental innovation), and to identify possible gaps between actual and sought performance.The landscape covers four domains that influence innovation - the attributes of the individual, the organizational context in which he/she functions, the business environment (the market / industry in which the organization is operating) and the external environment. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a self-appraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization's particular innovation strategy and environmental context."

Jan 1, 2003

By T Goswami

The conventional practice in open cut coal strip mining has been to blast the overburden or coal layers in separate blast events. This is done in order to maximise the benefits from throw blasting and also to limit coal losses. Each blast event usually has a particular design of hole diameters, burdens and spacings, explosive charges and blast timing in order to achieve the required blast outcome for either the overburden or coal. This means that each blast has to be separately cleaned on the surface after excavation of the previous blast. Hole locations then have to be individually surveyed and marked, holes drilled, explosives and initiators loaded and the blast fired. Each of these actions takes considerable time and resources and therefore impacts on mine productivity. The mine has to be cleared for each blast event and every blast presents a new potential source for noise, dust or vibration disturbance to the neighbouring population. Exposed highwalls are also subjected to vibration and damage from each subsequent blast event

Jan 1, 2006

By D. J. Goodings, R. J. Bonenberger, H. U. Leiste, W. L. Foumey

This paper describes a series of two-dimensional tests conducted and filmed with a high-speed (500 frames per second) video camera. The purpose of these tests was to provide a better understanding of the processes involved in creating craters and channels in water covered soils with explosives.

Jan 1, 2000

By Corry Goumans, Dwayne Wallace

"On July 1, 1997, a rockslide occurred on the I-40 in Hayward County, North Carolina that completelyblocked all lanes and disrupted traffic flow in the region. Remedial measures were undertakenimmediately in order to open traffic, however on-going geotechnical investigation revealed stabilityconcerns that necessitated closing the highway to ensure public safety. Access to the top of the slope was available only from the bottom of the slide on the Interstate I-40. Excavation and trim blasting started from the top and along the west slope of the failure, however, additional geotechnical evaluation indicated that slope stability remedial measures were required to support the western rock slope mass."

Jan 1, 1999

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By Carl Lubbe, Ron Frye, Wayne Curtis, Julie Pecori, Dan Leach

Blasting conducted in the USA using the new Electronic Initiation System developed by Altech has shown that an accurate delay system will benefit the customer. Results from test work clearly showed that improved fragmentation was effected and blast vibration was at least similar to that currently found at the test venue with improvements possible.

Jan 1, 1997

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coottha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1996

By Carl Hendricks

Aquila Mining Systems Ltd., is the world leader in drill monitoring, control and GPS-based machine navigation systems for the mining industry. This paper will review the design and application of AQUILA’s drill monitoring, control and positioning systems currently in use throughout the world and some of the benefits that derive through their use. In 1993, AQUILA became the first company to install a high precision, cm level, real-time GPS receiver on a blasthole drill. In fact, this was likely the first application of GPS on any form of production mining equipment. To date, AQUILA has installed over 90 GPS based drill monitoring systems worldwide. Since 1992 AQUILA has continued to lead in the advancement of new technologies for drilling including real-time geology recognition and automated drilling control systems. The AQUILA DMseries drill systems offer mines the ability to collect and transmit to the mine office; drill production statistics, ore and waste intersections, exact collar elevations, hole positions and depths, maintenance information and consumables tracking. Unique office software developed by AQUILA provides an encompassing Windows environment within which to manage and coordinate all aspects of data communications and information management between the drills and various mine departments. AQUILA and Caterpillar, along with Mincom and Trimble Navigation are partners in a technology alliance that is providing the surface mining industry with vehicle tracking and navigation systems for all mobile production equipment.

Jan 1, 2000

By Mark A. Williams

"This paper was originally intended to be a presentation of a case study of two surface bituminouscoal mines in the southern Appalachian coal fields located within five miles of each other. These mines were nearly identical in every aspect from geologic setting to equipment application. Althoughrepresentatives from each mine desired to participate in the preparation of this paper through support in providing background information and in review and editing, it was later concluded that, due to the environmental sensitivity associated with each mine, it may not have been a good decision to present this case study in a public forum."

Jan 1, 1994

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

The first principle one usually Learns about blasting is that cunpetence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced blaster when operating in a new area, may have to make one or two shots just to acclimate himself to the new conditions with which he is faced.

Jan 1, 1989

By Sri Sawmliana, P. Pal Roy

Blasting Gallery (BG) method was introduced in India for higher production and low cost of excavation to substitute conventional hand section and stowing methods for thick coal seam. The Singareni Collieries Company Ltd. (SCCL) adopted this method in the year 1989 and since then successfully operating at GDK-10, GDK-8 & VK-7 Incline mines in Andra Pradesh, a southern state of India. It is also successful at Chora 10 Pit Colliery of Eastern Coalfields Ltd. (ECL) in West Bengal whereas at East Katras Colliery of Bharat Coking Coal Ltd. (BCCL) in Jharkhand State, the method has been partially successful due to some geological constraints of the area.

Jan 1, 2003

By Francisco Sena Leite, Pedro Brito, Auã Kiahla, Raquel Carvalhinha, Tomi Kouvonen, Vinicius Miranda

Shockwaves that generate vibration in the surrounding environment of a blast, are one of the most important factors to control drill & blasting works near delicate buildings as well as in sensitive structures (wall control). On top of the damage to the buildings themselves, sensitive equipment such as computers, measurement apparatus and medical devices can be also compromised. The most commonly measured values from vibration are PPV (peak particle velocity), acceleration and displacement. Some devices and techniques have been developed in the last decades to measure the impacts of these vibratory phenomena. This information can be used to predict levels of vibration for future blasts and improve their quality of design using the attenuation law. From traditional studies to modern seismographs, a range of solutions are used for this propose. The main problem of applying this kind of technology is the high cost associated with each measurement device. In order to measure the ground vibration using new technologies while lowering the cost, a device has been developed using a microcontroller and electronic sensors commonly found on the market. This new equipment was tested side by side with traditional seismographs and the results were sent to a server for analysis. After several blasts, the necessary data was generated for the validation of the prototype. Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper.