Search Documents

By Glaser. C., J. Balz, F. Logsch, R. Heiduschke, M. Leiker, P. Ay

The treatment of iron-hydroxide-containing water from ground water and surface water is achieved by a combination of the process steps of flocculation and subsequent mechanical dewatering. The aim is to create solid pellet structures by extending the structure forming flocculation process with a build-up pelletizing process which can be transferred directly into a drying unit. A Taylor-Couette-reactor (diameter of the inner cylinder – 40 mm, gap width – 5 mm) was used for these experimental studies. To produce the necessary flow profile the inner cylinder was rotated at a speed of 230 rpm. The iron hydroxide-containing suspension (dry matter content: 2 mass %) was added simultaneously with the addition of a cationic high-molecular flocculant in various flocculant dosages and residence times of 5 to 15 min. The pellets were examined for parameters such as geometric dimensions, dry substance content and dewatering behaviour. As the results show, there is a direct relationship between the residence time and the geometric dimensions of the pellets. After a residence time of 5 min, round pellets with an average diameter of 6 mm were formed. With an increase in the residence time up to 15 min, a compaction of the pellets could be observed, which resulted in an increase in the dry substance content of 8.0 to 11.2 mass % on average. After completion of the pelletizing process, the pellets were mechanically dewatered by filtration. By applying this innovative wet pelletizing of iron-hydroxide containing suspensions in a Taylor-Couette-reactor, it is possible to carry out the process of flocculation combined with the pellet formation with simultaneous pellet compaction in a single process step. The resulting pellet structures are distinguished from conventional floc structures by an improved water discharge capacity. After classification the pellets can be marked directly as easy-to-handle bulk material, suitable as feedstock in percolation columns for the purification of contaminated fluid streams

Jan 1, 2018

By Z. M. Dai

Microorganisms in AMD (Acid Mine Drainage) were enriched in 9K culture medium. The enrichment was applied to leach copper pyrite after the microbial community structure and metabolism was stable. Before and after bioleaching, the microbial DNA was extracted and applied to RFLP (restricted fragment length polymorphism) analysis to demonstrate the relationship between the leaching efficiency and the change of microbial community. Atomic absorption spectrometry results showed that when concentration of the pulp was 10% and pH were 1.5, 2.0 and 2.5, the leaching rate were 56%, 57% and 34% on the 18th day respectively. These results indicated that the rise of pH resulted in the decrease of leaching rate. In lower pH condition, the growth of microbe was faster: when pH was 1.5, the microbial cell number reached to 1.4×107cells/mL on the 9th day; while pH was 2.5, the microbial cell number decreased to 4×106cells/mL. The analysis of microbial community structure showed that Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans were dominant species before bioleaching (account for 43% and 32% respectively). And after bioleaching, these two species were still dominant when the initial bioleaching pH were1.5 and 2.0. While the initial bioleaching pH was 2.5, the proportion of these two species decreased. These results demonstrated that the initial bioleaching pH would affect the microbial community structure in bioleaching system at room temperature, and this affect could lead to different copper pyrites bioleaching efficiency.

Jan 1, 2014

Pure camsellite samples were prepared through crushing, sorting and grinding the high-grade iron-containing camsellite ores from Fengcheng, Liaoning, China. The flotation behaviour of camsellite was studied via a systematic investigation of camsellite flotation re-covery changes as a function of choices and dosages of collectors and depressants at different slurry pH. The results showed that at pH 8.5 to 9.5, the recovery of camsellite reached the maximum at 90%~93.5% using dodecylamine as the collector, while under the same condition a recovery of 84%~86% could be achieved with sodium oleate. The adsorption of dodecylamine was not affected by the addition of sodium hexametaphosphate, but the adsorption of sodium oleate could be significantly depressed. This implied that sodium metahexaphosphate could be used as an effective depressant for the other associated minerals during the dodecylamine flotation of camsellite. When starch was used as the depressant, the flotation of camsellite by sodium oleate was almost completely depressed in the alkaline conditions. Significant depressions were also observed when calcium chloride was added in the camsellite-sodium oleate system. The higher the slurry pH is, the stronger the depression. Zeta potential measurements indicated that the flotation was mainly initiated by the electrostatic adsorption of the collector on camsellite. X-ray photoelectron spectrometer (XPS) analysis showed that the adsorption was originated from the electrostatic attraction between the N atom in dode-cylamine and B atom in camsellite. Dodecylamine had a higher coverage on the camsellite surface than sodium oleate.

Jan 1, 2014

By Arkady Senchenko, Andrey Vasiliev, Alexander Aksenov, Metodi Zlatev

"This paper considers the issue of treating argillaceous oxidized ores with low gold grade (around 1.0 g/t). These ores according to their gold recovery level can be treated by heap leaching and agitation cyanide leaching, but low gold grade makes this treatment uneconomic. Heap leaching of argillaceous ores requires high consumption of binding agent for pelletizing to create suitable hydro-physical properties of material, which leads to increasing process cost and makes the material treatment unprofitable. Agitation cyanide leaching of this ore requires grinding processes; these expenses would not be paid back by the amount of gold recovered. Considering the above, poor argillaceous oxidized ores are recommended to be treated according to a combined technology including fractionation of ore, heap leaching of coarse fraction and agitation leaching of argillaceous fraction. Complex approach application allows one to avoid expenses incurred for material grinding and high consumption of binding agent for pelletizing. The success of this technology implementation will firstly depend on the quality of material fractionation, therefore the section of disintegration and division of ore into different components will be the most important part of flowsheet development for gold production. When disintegrating minerals at positive temperatures both standard (mechanical disintegration - scrubbers) and innovative (hydraulic method of disintegration - HydroClean units) equipment is applicable. HydroClean units are characterized by lower energy and water consumption. In a number of cases it is required to treat frozen ores. When treating frozen material standard approaches to disintegration are not reasonable due to their low efficiency. In order to treat frozen material a two stage disintegration flowsheet with screening after each stage is recommended. The first stage is recommended to be performed in a scrubber, the second - in a HydroClean unit. This technological flowsheet will provide high and steady values for ore separation into fractions at low energy consumption for disintegration."

Jan 1, 2014

By V. Ross

"The Upper Group 2 (UG2) reef in the Bushveld Complex in South Africa hosts an estimated 40% of the world’s Platinum Group Metal (PGM) resources. The processing of this ore via flotation poses two particular challenges: limiting the levels of chromite in the concentrate to reduce downstream smelting problems, and enhancing the recovery of ultrafine (typically -10 micron), liberated PGMs. Conventional ways of suppressing the entrained chromite, such as froth washing, is not effective in PGM operations, which are dominated by mechanical cells. The recovery of fine particles is hampered by low collision efficiencies with air bubbles, as well as oxidised surface layers especially in tailings operations. This paper documents the results of laboratory tests on a run-of-mine PGM UG2 ore, investigating the application of a pneumo-mechanical column (PMC) and its effect on PGM flotation and its selectivity with regard to chromite. A key feature of the device is the stage-wise release of aerated slurry from an agitated downcomer, thus creating conditions where the superficial velocity profiles of air and slurry change axially within the separation zone. This aids segregation of the silicates and chromite-rich fractions in the separation zone, concentrating the latter towards the bottom of the column and minimising its entrainment into the concentrate. Comparison of the performance of the PMC to that of mechanical laboratory cells under equivalent operating conditions showed improved PGM flotation kinetics and recovery. This was accompanied by a decrease in gangue recovery compared to the mechanical cells by more than 40%, thus doubling the final rougher concentrate grade from 50 to 100 g/t. Significantly, whilst the overall Cr2O3 recovery was reduced by more than 60%, the selectivity (PGM recovery vs Cr2O3 grade in the concentrate) was doubled.INTRODUCTIONThe Bushveld complex in the northern part of South Africa hosts the world’s largest reserves of Platinum Group Metals (PGMs), representing approximately 40% of the total PGE. It is characterised by three main PGM bearing reefs, namely Merensky, Upper Group 2 (UG2) and the Platreef. The Merensky and Platreef are dominated by silicates in the form of pyroxenites, and carry economically recoverable amounts of copper and nickel, in the form of chalcopyrite and pentlandite. The UG2 on the other hand is a chromitite ore with chromite as (ideally, FeO.Cr2O3) the most abundant gangue, often constituting more than 70% by mass with a PGM grade of around 4.5 g/t. Other key gangue minerals are pyroxene, feldspar and talc. The PGEs occur in a wide variety of minerals, with platinum and palladium sulphides typically accounting for about half of the total. Base metal sulphides such as chalcopyrite, pentlandite and pyrrhotite occur in only very minor amounts, accounting mostly for less than 0.1% by mass."

Jan 1, 2018

By L. Gao, X. Gui

Fine coal obtained from Kailuan mine served as the processing object of this study. This material was difficult to separate. A flotation rate experiment was designed to investigate the process distribution characteristics of size and density during fine coal flotation. Size and density analyses of five clean were studied. The mineral morphology of flotation rate experiment cleaning was observed through scanning electron microscopy. The fractions -0.074+0.045 mm and -0.045 mm exhibited the best practical floatability and presented the highest combustible body recovery rates, but the selectivity and natural floatability of these two fractions were the worst. The - 0.074 mm fraction has contaminated the clean coal from the early stage of flotation, and the cumulative clean coal ash of -0.074 mm reached up to 17.20%. The low and middle-density classes displayed varying flotation behavior, but the flotation yield difference was only nearly 3%. The middle-density class caused the clean coal to have high ash content. The poor selectivity of fine coals, middle-density fraction, and fine mud resulted in high-ash clean coals during flotation. Thus, improving the selectivity of fine coal, restraining the flotation of fine mud, and grinding the coal to decrease the middle density mass fraction to liberate clean coals can yield high-quality clean coals through flotation.

Jan 1, 2014

By H. Araneda

Throughout Chile?s history, mining has consistently been a leading industry in the country. The 1990s marked the beginning of a boom in Chile?s mining industry, especially in copper mining, due to both foreign and local direct investment in the sector. Mining?s contribution to the GDP was 15.6% at current prices in 2009, and it accounts for 56% of the country?s exports. Chile?s copper market share reached 35% in 2009. The investment portfolio in mining in Chile for the coming decade has been estimated at 90 billion US dollars. The acute scarcity of human resources currently experienced by the mining sector in Chile will be accentuated in the coming decade as a result of this scenario of investments. The situation is, additionally, similar to the one confronted by other countries involved in the mining industry such as Australia, South Africa, Canada, and in Latin America includes, Peru, Colombia and Brazil. A study carried out by Fundacion Chile, ¨Labor Force in the Chile Mining Industry, Diagnostic and Recommendations, 2011-2020? shows the projected labor shortage for the operation of projects in the development stage, considering only the requirements of the process of extraction, processing, and maintenance. The demand, accumulated incrementally, will be around 115,000 technically skilled workers, professionals, and qualified workers. This figure refers to the operational work force, and does not include the human resources that will be required for the prior stage of the engineering and construction of the projects (brownfield and greenfield). The demand for technically skilled workers and professions for the stages of engineering and construction of the projects that have already received investments is estimated to be 190,000 people for the period 2012-2020. The peak of the demand for engineering is 2012, with a figure that surpasses the 12,000 professionals for all of the engineering specialties. The analysis of the formation of human resources at the tertiary level (where tertiary includes technical/vocational and academic degrees at the undergraduate level) for mining and related majors demonstrates that the programs are scarce with a bias toward theoretical contents and that they are excessively long (40% longer than comparable programs in Australia, Canada, and in OECD countries). The completion rates are low, especially in the technical-vocational programs, which have a completion rate of only around 30%. Finally, the rates of attraction of technically skilled labor and professionals towards careers in mining are insufficient to reduce the identified skill gaps. In the case of university professionals such as geologists, mining engineers and engineers in metallurgy, 80-90% will work in mining. In the case of graduates of relevant majors, that cover skills also utilized by other industries, not only mining?such as maintenance workers, operators of fixed and mobile equipment, etc.?the mining sector appears to be unattractive for reasons such as shift schedules, geographical location of work sites, and other factors. On the basis of the available diagnosis a strategy for the sector has been developed (Workforce Development and Skills Strategy) whose objective is (i) to define a Mining Qualifications Framework to identify the critical roles to be filled (ii) to start, with public resources, a ¨fast-track? training program to assure the availability of at least 28,000 operators (machinery operators, truck drivers, etc.) and maintenance specialists in 2015 (iii) to promote the development of training hubs for mining with learning technologies to train technical labor and professionals on the basis of world class standards (iv) to design and implement a campaign oriented toward the perception of mining as an attractive field of employment opportunity (v) to develop curricular innovations for tertiary education programs, on the basis of international benchmarks. Keynotes: Chile, mining, copper mining, skilled human resources

Sep 1, 2012

By Manochehr Oliazadeh

"Water shortage becomes a major challenge in mining industry. The best example is Chile where the Chilean authorities declared a state of emergency in 2012. Depletion of high grade ore-bodies necessitates the use of low grade ores. If the demand for metals remains constant, more low-grade ores need to be mined to produce the same tonnages of metals. This increases the water demand in mining industry. Mining industry competes with other industries such as agriculture and manufacturing. Agriculture and manufacturing consume 1500 and 2300 billion m3 water respectively. The global use is 4500 billion m3 while the mining uses 80 billion m3 of water per annum.To tackle the water challenges in mining industry and also avoid competing with other users for fresh water, many efforts have been made, including using lower quality waters to reduce the fresh water consumption in ore processing. Saline water or hyper saline water from seas or the ground is accessible; however the cost of desalination is remarkable. Desalination plants and associated pipelines and pumps capital cost can easily exceed $ 500 million. Saline water will certainly increase the operating costs due to high wear rate of mechanical equipment but at current situation of mining industry spending all this money upfront does not look attractive. Desalination leaves salt on land at mine site which may create environmental issues.Dry processing can be a solution for water shortage in mineral processing. Wet processes dispose tailings on land with little or no agricultural productivity. It also may contaminate surface and ground water and generate dust. This paper reviews the water consumption by various mineral commodities, discuss briefly about recent of application of salt water in mineral processes and finally discuss about dry processes as alternative solution for water shortage in mining industry."

Jan 1, 2014

By ?. Kostadinov

Theoretical study of the behavior of grinding medium presented by TBP (tetraballpebs) was conducted by computer modeling of the position of grinding medium at different speeds and different drum fill factor. For the modeling were used known equations of motion derived for the ball load. Algorithm was created by SolidWorks software, allowing determination of center of gravity of the load in the mill and energy for grinding. These results were compared with similar results obtained by ball grinding medium. The capabilities of both grinding media are demonstrated by graphics under the following conditions: 1.Equal dimensions of the experimental model of the mill; 2.Equal mass of the grinding loads; 3.Comparison of grinding bodies with the same number, mass and density. Keywords: simulation, behavior, grinding medium, balls, tetraballpebs

Sep 1, 2012

By E. V. Zelinskaya, A. E. Burdonov

"In the raw aluminum production processon electrolyzers with self-baking anodes, during technological operations, flow-regulated treatment and adjustment of the electrolyte chemical composition produced by diesel and floor-rail technology, alumina and fluoride salts are spilled through the ventilation grilles of the electrolysis body aeration channels, leakage in the equipment, machinery and motorized machinery construction elements. As a result of this, a part of the bus station and the level of ± 0 (the basement room with supporting curbstones and columns, on which electrolyzers are installed) are covered with technological raw material. This leads to an increase in the conductor (bus) resistance, contact connections deterioration, cell insulation failure and raw materials loss. For example, at the enterprise ""Rusal-Bratsk"", as a result of the activity, up to 420 tons per month of alumina-containing wastes that are unfit for use in the electrolysis process are formed due to the alumina substantial contamination with salts of iron and silicon, which significantly reduces the technical and economic parameters of the electrolysis process. The main scientific problem is the processing (cleaning) of alumina-containing waste having a complex mineralogical composition of the material, its contrast and structure, from oxides of iron and silicon, using ""dry"" separation methods. In the performing the work process, qualitative indicators of the influence of external factors (air humidity, precipitation, sunlight, temperature difference) on the physicochemical processes components interaction during the raw materials storage are established. On the basis of laboratory tests, it is established that alumina-containing raw materials can be separated and photometric and gravitational separation methods used. A mathematical model of the motion of particles of primary and prepared alumina-containing raw materials in a cascade-gravity classifier was developed. The criteria and factors characterizing the alumina-containing material, as well as influencing and determining the maximum material enrichment, are established."

Jan 1, 2018

By Subrata Roy

The slag produced in metallurgical smelting processes contains considerable amount of valuable metals. The present work focuses on recovery of copper value by froth flotation from the copper smelter slag. The slag samples are subjected to detailed characterization including automated quantitative mineralogy using Mineral Liberation Analyzer (MLA). The MLA results indicate that a part of copper is present in sulphide form in fayalite (iron-silicate) matrix and very poorly liberated. SEM-EDX analyses also reveal that a certain part of the copper is present within the fayalite (Fe-Ca-Si) matrix, perhaps either as lattice impurity or very fine grain. The copper smelter slag is ground in wet mode in a ball mill, to particle size distribution suitable for flotation. Subsequently, the slurry undergoes froth-flotation in lab-scale Denver-type flotation cell. Various combinations of sodium iso-propyl xanthate (SIPX) and alkyl hydroxamate collectors are used along with pine oil as frother. A multiple collector dosage is required for effective flotation of non-sulphide copper phases associated fayalite and alkyl hydroxamate is identified as one of the effective collector for non-sulphide minerals. The copper recovery can be enhanced by 7-10% with a combination of collectors as compared to conventional sulphide flotation using only xanthate type collectors. However, the grade decreases to some extent. Keywords: flotation, copper slag, hydroxamate collector

Sep 1, 2012

By Juan B. Yianatos

"After almost 100 years, since the first commercial application began in Australia, flotation has shown an extraordinary growth and nearly 2 billion tons of ore per year are presently treated by flotation processes. During this time flotation has promoted a wide scope of research activities ranging from fundamental chemistry and hydrodynamic studies to studies of industrial operations. In general, fundamental studies have been mainly related to ideal situations. In recent years, however, large efforts have been focusing on achieving a better insight into the actual sub-processes provided by the development of new and more sophisticated instrumentation. Since the massive incorporation of flotation columns, around 15 years ago, a renewed interest in flotation fundamental studies, process modelling and new cell designs have been observed worldwide. The key role of the froth has been recognized as an independent and sometimes rate limiting process step. Thus, separation of pulp and froth process stages seems the most appropriate in terms of process modelling, diagnostic, design and scale-up purposes.In relation to flotation equipment development, until the middle of the 1970?s, only the sub-aeration mechanical cells were dominant. Since the 1980?s, the use of pneumatic cells and forced air mechanical cells has emerged strongly. Also, in the last decade, flotation equipment has shown a dramatic increase in size, reaching values of 200m3 in unitary mechanical cells and more than 300m3 in columns. The general feeling, however, is that, despite the great advance observed in terms of process knowledge, the mechanisms and principles of industrial flotation cells design and scale-up are still not fully understood.Advances in process instrumentation and control now in use allow for more efficient operations, both in metallurgical performance and savings in operating costs.INTRODUCTIONFlotation is a widely used process within the minerals processing industry, as well as being used for water treatment and de-inking of recycled paper. Froth flotation started in Australia at the beginning of the 20th century and since then flotation technology has made significant advances. Flotation was firstly applied to sulfide ores. The largest tonnages treated by flotation are copper and copper/molybdenum ores, handling about 50% of the total ore processed. Also significant are phosphate, iron ore and coal treatments. At present, Chile is the foremost copper producer in the world with around 35% of the world?s production. Figure 1(a) shows the evolution of copper production in Chile over the last decade. The total amount of fine copper produced in year 2001 was 4.7 million tons, from which 3.2 million tons was processed by flotation while 1.5 million tons went through LIX-SX-EW processes, which also showed significant development during the same period (Anon, 2001). The total flotation treatment of copper ores in Chile is about 325 million tons per year (Anon, 2002), so the world treatment of copper ore by flotation can be estimated at about 1 billion tons per year. Consequently a total of nearly 2 billion tons of ore per year is presently processed worldwide by flotation (Fuerstenau, 2001). In order to handle the higher tonnage of low-grade ore, a worldwide trend towards the development and use of larger flotation machines began in the 1960?s. Figure 1(b) shows that the trend became extremely marked from the beginning of the 1990?s, which is consistent with the strong increase in copper production during the same period."

Jan 1, 2003

By Rasool Hejazi

The feed to Chadurmalu iron ore concentrator plant is a mixture of magnetite and haematite iron ore with a Fe/FeO ratio of about 8. The feed to plant, after grinding via wet SAG mill, is pre-separated by wet low intensity magnetic separator. Magnetic product is conducted to magnetite processing circuit for producing magnetite concentrate, and nonmagnetic product is directed to haematite processing circuit. Due to surface oxidization of magnetite particles and a decrease in magnetic attraction properties, significant amount of these particles are misled to tailing which results in decreasing the efficiency of haematite processing circuit. This problem can be remedied by using magnetic drum separator with more magnetic intensity and/or gradient. In this paper, the replacement of LIMS separators with wet medium intensity magnetic separators with a field intensity of 3800 gauss on drum surface (MIMS) have been suggested and considered as the most suitable solution to prevent the loss of magnetite particles. The results of carried out investigations with replacement of drum separators in industrial scale, showed that utilizing MIMS in magnetite processing circuit resulted in increasing final concentrate weight recovery on average by 2.59%, without any adverse effect on the concentrate quality; decreasing the magnetite content in the feed to high gradient magnetic separator (HGMS) by about 3.5%; decreasing the feed to floatation part by about 7% and consequently decreasing consumption of chemical reagents; increasing Fe/FeO ratio of the feed to plant. Keywords: iron ore, medium intensity magnetic separator, haematite, Chadurmalu

Sep 1, 2012

By Z. H. Wang

The internal parameters of ball mill are very important in the grinding process and have significant impact on the grinding results. Accurate measurement of the internal parameters of ball mill is crucial and indispensable for optimization and control of grinding process. In this paper, a novel tri-sensor measurement method was used to measure the external signals (i.e., bearing pressure, sound intensity and power consumption) of ball mill. Mathematical models, which link the external signals of ball mill with its internal parameters, were established to predict the internal parameters of ball mill. Experimental results showed that the mathematical models could directly predict the internal parameters of ball mill once the external signals were obtained. The tri-sensor measurement method and the mathematical models proposed in this paper provided a new way and solid basis for optimization and control of ball milling.

Jan 1, 2014

By John C. Gathje, Rick Moritz, Wilhelm de Beer

"Froth flotation has a long history of success for the recovery and concentration of a wide variety of minerals of commercial interest. Both the art and science of flotation have progressed greatly, and as our knowledge has increased so has our ability to improve mineral separations and recoveries.One area of interest in recent years has been the flotation of refractory gold ores to recover the gold-bearing sulfides. In many instances, the use of conventional air flotation to concentrate these values has achieved only limited success. However, as a result of intensive research, Newmont Mining has expanded the boundaries of flotation, and it can now be used to successfully treat many gold-bearing sulfide ores as well as platinum and palladium ores. This has been achieved through the use of the N2TEC technology, which utilizes nitrogen as an inert gas in the flotation process.Laboratory and pilot plant investigations and a commercial plant have proven its worth. Compared to air, the patented N2TEC process has increased the gold recoveries of many ores by 5 to 15 percentage points, and improvements of an even greater magnitude have been observed. This paper describes the process development for the flotation plant now being operated at Newmont’s Lone Tree Mine located in Nevada, as well as development work that was done on ores from their Twin Creeks Mine also located in Nevada."

Jan 1, 2003

By S. Gerl

Since Schönert, 1980 a multiplicity of scientists have dedicated themselves intensively to the scientific investigation of wet grinding in agitated media mills. The achieved research results led to a clearly improved understanding of the comminution mechanism in wet operated agitated media mills and in consequence also to clearly more efficient machines. In contrast to this the standard of knowledge on dry grinding in agitated media mills is still very small. The practical experience from numerous plants shows however that the transferability of knowledge from wet grinding to the dry grinding regarding transport phenomena and comminution behaviour, influence of the operating parameters and also wear is very limited. In the industrial application above all the continuous mode of operation is preferred. The main problem which has to be solved in agitated media mills is minor the comminution itself, than rather the question of the trouble free material supply and material extraction as well as the cooling of the mill. The agitated media mill MaxxMill® offers an innovative concept to overcome the feeding and extraction problem with its rotating grinding chamber, the eccentrically mounted agitators as well as the eccentric flow deflector with integrated material supply. Because of the pneumatic extraction of the ground materi-al cooling of the milling chamber is not necessary. On a MaxxMill ® laboratory mill with a 5 litre grinding chamber volume extensive parameter studies were carried out to study the influence of operating parameters on the continuous dry grinding of quartz sand. The test were performed in a continuous single pass operation without classification of the final product. Apart from the influence of the throughput rate on fineness above all the influence of the agitator and grinding chamber speed as well as the grinding media size was examined.

Jan 1, 2014

By F. Bello, J. Engels

"During 2012 and 2013, Minera Esperanza conducted a series of thickening and deposition trials to identify design and operational parameters associated with increased thickening of its tailings. These trials focused on benchmarking the current solids concentration of tailings (62 - 64%) in anticipation of an increase to 67% solids once two new 45 m diameter deep-cone paste thickeners are commissioned in 2014. These trials studied the sedimentation and rheological characteristics of the existing tailings and performed deposition modelling to assist with developing short- and long-term designs for the tailings storage facility. To verify and optimise these models, Minera Esperanza considered a series of laboratory, pilot, and industrial-scale deposition trials. This paper provides a review of the trials conducted in the laboratory and at industrial-scale and considers the results and optimisations for the short- and long-term design of Minera Esperanza’s tailings storage facility."

Jan 1, 2014

By Bianca Foggiatto, Marko Hilden, Malcolm Powell

"Since the introduction of the concept of flexible circuits (Powell and Bye, 2009), it has been further developed and refined to the definition of ‚FlexiCircuits leverage ore variability to maximise resource utilisation?. The focus of flexible circuits is to investigate processing options that provide extra capacity through sophistication rather than scale. This requires a combination of smart ore characterisation, economic modelling and innovative processing plant design. Flexible circuit design can reduce energy requirements through gangue rejection or progressive ore upgrade; and increased robustness and controllability by leveraging off ore variation. Each rock type, as characterised through Geometallurgical ore modelling, may be processed more efficiently by individually optimising processing paths. The objective of FlexiCircuits is to transform the processing capability of comminution and concentrator plants - targeting step change in performance through integrating a range of interrelated improvement opportunities. Considerable effort has been applied to developing the modelling and simulations tools required to develop and demonstrate the potential of this concept. This paper presents a practical application as a test case. A realistic application of flexible circuits is provided through a conceptual circuit design of an iron ore processing plant. It is simulated as a multi-component feed with a range of new models in the researcher’s Model Developers’ Kit (MDK) to trial the ability of different circuit designs to respond to variable ore and quantifying the potential of these circuits to transform processing capability of variable ore feed. The outcomes of the simulations are presented and discussed, providing a practical demonstration of the level of modelling and simulation required and the potential of flexible circuit design."

Jan 1, 2014

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By Peter N. Holtham, Geoffrey J. Lyman, Matthew S. Brennan, Vijay Subramanian, Rui X. Rong, Tim Napier-Munn

Studies of the dense medium and classifying cyclone have been conducted using the Fluent computational fluid dynamics code. Experimental measurements of the segregation of medium in a DM cyclone by gamma-ray tomography and the performance of a novel classifying cyclone design have been used to test and interpret the 3D CFD predictions. The predictions of the CFD models were generally plausible, though more work is required to incorporate turbulent mixing of the slurry in the cyclone. The benefits of the novel cyclone design were explained by the model in terms of conditions favouring reduction of short-circuiting at the vortex finder, and the removal of the air core from the wall at the apex. Work is continuing.

Jan 1, 2003