Search Documents

By Martin D. Larisch

The construction of diaphragm walls and most large-diameter bored piles (piers) is often carried out under drilling support fluids to temporarily stabilise the excavation prior to concrete placement. In most cases such fluids are either mineral-based slurries (bentonite) or polymer support fluids. The working mechanisms of these two fluid types are fundamentally different. Designers need to consider possible fluid-related impacts on the permanent design performance of the project-specific deep foundations as well as for the temporary excavation stage during construction. Robust design methods for bentonite slurry-supported excavations have been developed in the last few decades and the working principles and associated risks of such mineral-based slurries are understood reasonably well. However, such meth-ods have not been developed in detail for polymer-based drilling fluids. This document provides a brief overview of the main characteristics of bentonite- and polymer-based drilling fluids as a guide for construction practitioners and design engineers alike. The paper also high-lights some common construction risks related to casing installation and the selection of suitable fluid systems for different ground conditions. Typical defects caused by the incorrect application of drilling support fluids, and their pro-active mitigation, are discussed, too. In addition, the basic concepts of sta-bility calculations for bentonite fluid-supported deep excavations are briefly introduced and their ap-plicability for other fluid types such as polymer-based support fluids or water are reviewed.

Nov 1, 2022

By Seth H. Hamblin, John E. Regan, Dimitrios Palantzas

"Through reliability-based calibration of larger pile load test databases, recent developments of the Load Resistance Factor Design (LRFD) methods, which include geotechnical load and resistance factors for deep foundations design, have advanced the state of practice for geotechnical engineering. These load test databases upon which the current geotechnical load and resistance factors have been developed are limited, however, and do not provide sufficient data to support the development of resistance factors for uplift (tension) pile capacity. As such, some recommended resistance factors for uplift capacity estimation methods are simply derived by reducing the recommended resistance factors for piles in compression by a factor of 0.10.The results of three (3) tension loading tests performed to failure on 508 mm (20- in) square precast, prestressed concrete piles, driven though granular soil in southeastern Massachusetts, are presented and compared to static pile capacity calculations and dynamic analyses performed using the Pile Driving Analyzer (PDA) during installation. These results are presented along with current recommended LRFD resistance factors for driven piles under uplift (tension) loading conditions. These comparisons offer an assessment of the applicability and limitations of current resistance factors methods for piles under uplift loading and may be useful additions to the existing database for future calibrations of LRFD resistance factors for driven prestressed concrete piles in sand.IntroductionIn 2010, two (2) natural draft cooling towers were constructed by Kiewit (Kiewit) Construction Company of Woodcliff Lake, New Jersey at the Brayton Point Power Station in Somerset, Massachusetts. These massive 500 foot tall, 400 foot diameter cooling towers were designed to convert the existing “open loop” system into a “closed loop system” thereby dramatically reducing the thermal impact to Mt. Hope Bay.Based on design guidance from the German VBG Design Code and the Massachusetts State Building Code (MSBC), tension (i.e. uplift) and lateral loads due to wind loads and design seismic events represented the critical loading conditions.Weighing approximately 190,000 kips upon completion, the cooling tower loads are transferred to 44 foundation nodes (i.e. pile caps) evenly spaced along ring beams which run the circular perimeter of each tower base. Each pile cap node was designed to resist a 2,000 ton compression load, 200 tons in tension (i.e. uplift), and 600 tons in the lateral direction."

Jan 1, 2015

By Alexander Scheuermann, Martin D. Larisch, David J. Williams

"Drilled displacement piles (DDP) have been used around the world for decades as foundation elements for structures and embankments. Typically the pile toes are designed to penetrate into stiff or dense soil formations to achieve sufficient base resistance. Recent research at The University of Queensland in Brisbane, Australia has discovered that the in situ stress conditions in stiff to hard clays is directly related to pile installation rates, which in turn are a function of the piling rig capacity and ground conditions. With adequate and constant pile penetration rates in situ stress conditions in the stiff to hard clay are increased by about 40%, resulting in significantly higher pile capacities. If pile penetration rates are too slow the in situ stress conditions are reduced considerably by remoulding and shearing of the clay, potentially causing reduced pile capacities. The paper presents the results of full-scale test piles at a stiff to hard clay site installed using different full-scale piling equipment.INTRODUCTIONDrilled displacement piling (DDP) is a piling technique in which a hollow stem, fitted with a purpose built displacement tool at the bottom, is drilled into the ground. Dissimilar to non-displacement piles, like Continuous Flight Auger (CFA) piles or conventional rotary bored piles drilled with kelly bars, the soil is not excavated during the DDP penetration process, but is displaced laterally and to a lesser extent vertically. The cavity created by the drilling tool is filled with highly workable concrete during the extraction process. The DDP technique is very economical providing high production rates and creating only marginal drill spoil, which has led to its increased global usage during the last decade. The typical DDP installation process is described in Figure 1."

Jan 1, 1900

By Marcus Daubner, Karsten Beckhaus, Florian Bauer

The construction industry can and needs to contribute to a more sustainable world. Accordingly, geotechnical works potentially have a significant share. In this context, Bauer understands “sustainable products for geotechnical works” as those that may cause less emissions and increase the sustainability of construction activities. In order to structure the efforts and systematically pursue sustainable targets in the construction sector, and in the specialist foundation industry, the “17 sustainability goals” presented by the United Nations in their AGENDA 2030, can be used for general guidance and for continuous improvement. Benchmarks for relevant economic and social objectives, mainly with environmental aspects, are inevitable. The key parameter to sustainable products for geotechnical works in the focus of this paper is the optimisation of processes on site needed to fulfill the client’s building task, including the selection of technologies and construction methods with minimum environmental impact and minimum carbon footprint.

May 1, 2022

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Edward C. Clukey

"Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed.During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor’s QA/QC program should be increased to achieve a foundation system with the required level of reliability.Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially “at-risk”. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.IntroductionThe foundation support system for the process train at a major LNG facility comprises more than 6,000, 23-m long DMM elements. The general subsurface stratigraphy at the project site comprises (from the ground surface): (i) up to 8 m of fill sand initially placed underwater building to a stable construction platform; (ii) up to 12 m of soft organic clay (Unit II clay); and (iii) clayey sand and sand layers becoming progressively denser with depth (Unit III sands). Each DMM element comprised two secant 1.5-m diameter DMM columns. DMM elements were typically arranged as cells enclosing one, two, or three DMM elements."

Jan 1, 2017

By Waddah Akili

The demand on pile installation in the offshore of the Arabian Gulf has, over the last two decades, experienced unprecedented boom, triggered by the construction of platforms, to help facilitate the production and transport of oil and gas. Available borehole data show that ground conditions for pile installation in the offshore is highly variable, resulting in misassessment of insitu conditions, leading to a huge discrepancy between ultimate pile capacities, based on design, and actual capacities after installation. The paper makes use of pile installation records derived from several platforms in the offshore of the state of Qatar, the Gulf Region. More specifically, the paper evaluates “as–installed” ultimate capacities and safety factors, recommends remedial installation procedures, and proposes a means for determining pile acceptability for piles meeting refusal short of design penetration. The paper offers what is believed to be relevant recommendations to guide the design and installation of future offshore structures; enabling the geotechnical community in the Region to solve their current offshore pile installation problems and gain an added margin of confidence regarding the ultimate capacity of installed piles.

By Toshio Yonezawa, Helmut Florian, Herbert Kuh, Masamichi Aoki, Takao Koono, Franz-Werner Gerressen

"To increase the bearing capacity of the ground, soil improvement technique is often adopted. One advantage of soil improvement techniques is the fact, that the impact to the environment is low, as the system utilizes the existing soil. Recently, compressive strength of soil improvement gets more into the focus for the use of building foundation. To prevent brittle fracture, which is a weak point of soil improvement, fiber reinforced soil improvement has been developed. Laboratory tests were conducted to examine the fibers suitable for reinforced soil improvement, and examine the optimum mix design for fiber cement slurry. Based on the laboratory tests, polypropylene fiber and cellulosic viscosity admixture was selected. For the laboratory tests a scaled model of CSM mixing head was used to examine the dispersion of the fibers in the ground. Using the CSM mixing head, the outer periphery fibers of soil improvement seemed to be arranged in the vertical direction, toughness performance of the soil improvement could be improved. Furthermore, full scale field test was performed using actual CSM unit, modified to enable the use of fiber mixed slurry. The validity of the material as well as the toughness performance of the soil improvement, determined from lab test results, was confirmed. In addition, it was confirmed that fiber reinforced soil improvement can be constructed appropriately by CSM method.2 INTRODUCTIONSoil improvement technique to improve the strength and deformation performance of ground has been used for a long time. Cement improved methods, with the increase of the deep Mixing Method, which has been disseminated since the 1970's, was often used since. Cement used soil improvement technology has been utilized to stabilize excavations, slopes in embankment and much more. Recently, it can be used for preventing liquefaction by building soil improvement in a grid (Suzuki et al. (1996)), and also as basis of the structure by increasing the compression strength of soil improvement (Yamashita et al. (2011)). Cement used soil improvement method, a technique for mixing the in-site soil and cement, can effectively utilize natural resources, and it can be expected that its use will increase further in the future. Therefore, soil improvement technique will be able to minimize the impact on the environment. Cement improved soil is a mixture of soil particles and cement with high compressive strength but low tensile strength. Since tensile strength of soil improvement is low, brittle destruction occurs. Therefore, it is not possible to use soil improvement in conditions acting with bending stress. If a horizontal impact force occurs in the improved soil, the width of the soil improvement needs to be increased to reduce the bending stress. If preventing the brittle fracture of soil improvement, the width of soil improvement could be reduced, then less resources would be needed. In order to increase the tensile strength of the soil improvement, several studies for the mix of fiber and soil were performed. Victor (1992) indicates cracking deterrent effect by fiber based on laboratory tests. Moreover, based on laboratory tests, Hayasaki (1982) illustrated the effect on the tensile strength of the fiber types, the type of fiber, the diameter of and the length of fiber."

Jan 1, 2015

By R. Paul De Bruyn

A. Crane Check List -- Make -- Model -- Year of Manufacture -- Where is load chart? Is it for this crane? -- Boom style and length -- Boom tip drawing (sketch) for fixed lead connection. Has the crane manufacturer been consulted on the point of attachment? -- How many drums; diameter and length of wire rope. -- Is the single part line pull enough to lift pile or hammer on single part line? -- What is the effective weight of the whole driving system - leads, pile, hammer, etc? -- Are there any auxilliary hydraulic systems? Are the line pulls on these adequate to lift the pile or hammer? -- What is the anticipated working radius? Will the spotter collapse to that length? -- Nature of foundation under crane - barge, marsh, unstable sand, etc. -- Does the crane meet OSAH and state regulations -current certification. Note - the operator is responsible for compliance with regulations. -- Is there any extra weight added to counterweight by compressors or hydraulic systems? What does crane manufacturer say? Consult factory before adding.

Jan 1, 1990

By Ezra Ballinger, Matthew R. Glisson

Located in downtown Fargo, North Dakota, the Block 9 Redevelopment project site contains highly- compressible soils in the upper 100 feet with groundwater about 10 to 15 feet below the existing ground surface. The owner prohibited using driven piles to avoid disturbing neighbors of the project and historically, drilled shafts are used in Fargo as a reduced noise and vibration alternative to driven piles. However, developments over the last 20 to 30 years in drilling equipment, load testing and integrity testing resulted in the project team identifying augered cast-in-place piles as a suitable alternative for this project. To reduce the risks associated with using a relatively unproven foundation system in the area, the project team used the design-build delivery method for foundation design and construction. The team also specified compression load testing and higher-than-normal integrity testing. A successful bi-directional load test validated the design parameters for the augered cast-in-place pile while thermal integrity profiling gave the team confidence that these piles would perform similarly to the test pile. PROJECT DESCRIPTION The Block 9 Redevelopment project goal was to turn an existing, at-grade parking lot in downtown Fargo, North Dakota into a public outdoor plaza, a mixed-use building and a parking ramp. The project provides new offices, retail spaces, a hotel, a restaurant and private apartments. Situated in the southeast quadrant at the intersection of Broadway and 3rd Avenue North, the project site wraps around a bank building that was to remain. According to aerial photographs, the eastern portion of the site contained a public parking ramp that was constructed between 1952 and 1976, and subsequently demolished between 2009 and 2010. The western portion of the site had some combination of buildings and surface parking visible in aerial photographs taken between 1952 and 1979. Since 1984, aerial photographs show the western portion of the site being entirely surface parking. The redevelopment included the construction of three structures: the Tower, the Podium and the Parking Ramp, as shown in Fig. 1. With plan dimensions of roughly 100 feet by 100 feet, the Tower has 1 level of below-grade parking and 19 above-grade levels rising to a height of about 230 feet above grade. The Tower contains eight levels of commercial office space, four levels of hotel, six levels of residences and a mechanical level. This configuration resulted in column service loads ranging between 435 and 2,685 kips. The Tower core area has a total service load of about 30,000 kips.

Jan 1, 2019

By Arash Khosravifar, Ali N. Ibrahim

"Large areas of Iraq are covered with collapsible soils namely gypsiferous soil which is often used as the foundation soil for structures. In particular, the Mosul Dam foundation is comprised of high contents of gypsiferous soils. Intrusion of water through the foundation soil dissolves gypsum which acts as the binding material between soil particles. This phenomenon results in the formation of collapsible soils which can cause serious damages to the dam structure. The failure of Mosul Dam, with a reservoir as large as 11 billion cubic meter of water, can be catastrophic. In the past, Mosul Dam Authorities have been remediating the soil foundation by injecting cement mortar. This method has been proved not economic; therefore, new, more efficient, methods are desperately needed.This research study focuses on finding practical methods to remediate collapsibility of gypsiferous soils by improving their geotechnical properties. This study presents remediation of collapsible gypsum-rich soil by grouting. Three types of stabilizer materials were used to make the grout; (1) sodium silicate (Na2 O3 Si) which is a well-known chemical soil stabilizer, (2) bentonite slurry, and (3) silicone oil. The purpose for using these stabilizer materials is to provide an impermeable layer (waterproofing coat) around the gypsiferous soil particles and to fill the voids that may occur in the soil as a result of gypsum dissolution when subjected to water.A series of double oedometer (collapse) tests and direct shear tests were carried out on gypsiferous soils before and after remediation by grouting. The results show that the soil compressibility decreases in the grout-treated gypsiferous soil by reducing volumetric strain. Consequently, the potential for collapsibility decreases too. It was also shown that grouting, increases the shear strength of the soil at confining stresses smaller than 250 kPa by increasing the cohesion combined with a slight reduction in the internal friction angle.INTRODUCTIONGrouting is one of the ground improvement techniques which is often used to improve the loose foundation soils. Bruce (2003) provides step-by-step procedures on using grouting techniques for sealing dams and other water reservoirs. Grouting can be classified as permeation grouting, compaction grouting or hydraulic fracturing. Permeation grouting is an effective way to send the grout into the ground without disturbing the soil structure, i.e. free flow of grout into the soil voids where grouting is accomplished by injection of a fluid-like material that is capable of forming a gel and binding the soil particles together. Grout materials may be solution grouts or suspension grouts. The permeation grouting technique is generally used to minimize ground permeability and to control ground water flow, but it can also be used to strengthen and harden the ground (Raman et al., 2012)."

Jan 1, 2017

By Chu E. Ho

This paper describes a case history involving the use of the Equivalent Driving Energy concept for evaluating timber piles that failed to achieve the termination criterion traditionally based on final driving resistance and minimum pile depth. It was assumed that a pile would be acceptable if the overall energy delivered during pile driving was at least equal to that of an ideal pile that achieved the design pile capacity established during an initial load test. The equivalent driving energy was determined by integrating the cumulative driving resistance profile over the embedded length of the pile within the founding soil strata. The required equivalent driving energy was calibrated using representative restrike PDA capacities of production piles as piling progressed. This approach enabled piles that failed to meet the original acceptance criterion to be re-evaluated, resulting in a significant reduction in the number of rejected piles that would otherwise have to be replaced.

By Frederic A. Verheyde

The CPT pile design method of the ‘Laboratoire des Ponts et Chaussées’ (LPC) uses the cone resistance (qc) for the design of axially loaded piles. It was originally proposed in 1982 and was revised in 1993 and 2012. It has been widely used in France for several decades and is included in the current French pile design code. The objective of this paper is to summarise the two first versions (1982 and 1993) of the method and to detail the most recent one as described in the current French pile design code (AFNOR 2012).

Nov 1, 2022

By Babak Mamaqani, Pirooz Barar

The Heights project was located at Fashion Valley North, San Diego, CA. The scope of the project was to replace two existing commercial buildings with a large 7-story multi-family residential building. There was an existing 1:1 slope on the north side of the site. A permanent soil nail wall, 1,000 linear ft long, with a maximum height of 100 ft, was needed to replace the 1:1 slope at the north side of the project to accommodate the development. Previously there was a design for the permanent soil nail wall which required up to 115 ft long soil nails with large diameter rebars and 13 in. thick permanent facing. PB&A was engaged by the owner to conduct soil nail design optimization and value engineering to reduce construction costs and improve scheduling. First, the SnailPlus program was used to check the stability under static and seismic conditions and to design soil nail lengths and sizes. Then, soil nail head forces were calculated to design the permanent facing using FHWA recommended procedure. Another challenge of the project was to evaluate the interaction between a future San Diego Gas and Electric (SDG&E) tower and the soil nail wall. Finite element analyses were conducted with the PLAXIS program to ensure the deflection of the future tower would be within the acceptable range. The soil nail design optimization helped the owner to save approximately $800,000 in construction cost and improved construction scheduling.

Sep 8, 2021

By D. Cantali

This paper will be presented in two parts. The first part will present the latest advancements in pile installation techniques using state-of-the-art press-in piling technology by Giken. By pressing in sheet piles and large modulus contiguous steel tube pile walls – as opposed to the more traditional installation methods using percussive hammers or vibrators – retaining structures can be constructed effectively noise and vibration free. For over water and coastal projects with limited access, this provides significant environmental benefits in the form of minimising the construction foot print and the impact to surrounding communities and the marine natural habitat. Typical noise and vibration data will also be presented. The second part of this paper will review the current manufacturing techniques for sheet piles and introduce innovative new materials used in the current piling market for embedded sheet pile walls. Materials include long service life non – ferrous materials such as new age plastics and fibre reinforced polymer piles. Their excellent long term performance and durability make them an effective solution in the marine environment. For steel piles, a number of steel grades with reduced corrosion characteristics will also be discussed including a newly developed steel to combat corrossion in the low water zone, an area often exhibiting the highest moments in a retaining wall. A number of project case studies will also be presented to reinforce their relevance in today’s changing construction landscape.

Nov 1, 2022

By Masaru Sakakibara, Ngo Tuan Anh, Mitsuo Nozu

"In the southern region of Vietnam and the southern United States, numbers of Deep Mixing (DM) columns have been installed to increase the stability of slopes and mitigate ground settlement. However, in some cases, there were some quality problems for in-situ cement mixing such as inclusion of unmixed lumps. According to the investigations by the X-ray diffraction analyses, electrical conductivity (EC) test, and careful observations of in-situ mixing quality, it has been observed that the existence of expansive soil and its high EC value cause the insufficient in-situ mixing. The countermeasures to address these problems have been taken.INTRODUCTIONIn South Vietnam, under the guidance of numbers of references and standards (Miki, 1998, JGS, 2000, Kitazume et.al., 2001, BS 2005), Deep Mixing (DM) has been used in recent years for soft clay improvement to increase the stability of slopes and to reduce consolidation settlement (Nozu 2005, Tung et.al., 2009, S. T. G. Peng et.al, 2009). However, at the initial phase of the DM operation, the authors have encountered some unusual phenomena such as (1) lower strength and inclusion of unmixed lumps (Figure 1), (2) less amount of up-heaved soil, and (3) sticking of large lumps of clay to the mixing blades. In regard to the above (3), Photo 1 shows one of the countermeasures against the sticking. By means of the placement of additional plates, the stuck clay has been reduced significantly.Subsequently, we have noticed that the quality of DM columns has not been so good, which meant that there have been some unmixed lumps in the column despite high cement dosage such as more than 300kg/m3. The authors also have encountered the similar incidents in Vietnam and United States during the deep soil mixing work. For example, Photo 2 is the core samples taken from the DM test column in northern Vietnam adopting cement injection during penetration (CIDP) procedure. To solve this problem, various tests and investigations have been performed so far (Nozu 2010, 2012)."

Jan 1, 2015

By Gustav Jahner, Michael Baltrusch, Norbert Hoffmann

Near the port city of Whitby in the north-east of England, Anglo American (AA) is setting up the deepest mine in the UK, which will have a depth of 1,500m. The purpose of the project is to extract and transport polyhalite, both underground, and to market it globally. As part of the construction works, BAUER Technologies Ltd, the UK subsidiary of BAUER Spezialtiefbau GmbH, constructed three different shafts using the diaphragm wall technique, with depths of up to 120m. In order to ensure the specified vertical tolerance of maximum 200mm, several measurement methods were applied, and the results were documented in a 3D model. Complex de-sanding plant technology and specially developed polymer products were adopted to regenerate the trench supporting bentonite-slurry.

Sep 1, 2022

By Xavier Pita, Alexandre Pinto, António Cristovão, Rui Tomásio

"The cutter soil mixing technology was been applied in Portugal since the last seven years. The aim of this paper is to present the main design and execution criteria, related with both the cofferdam and foundations solutions, using soil-cement panels, reinforced with steel profiles, at the new Leixões Cruise Terminal, located at the Leixões Port, in Portugal. The Terminal building was built with one basement on a marine environment, over very difficult geological and geotechnical conditions, which demanded the use of some unusual and integrated geotechnical solutions. It is also pointed out the importance of the QC/QA, as well as the technical, economic and environmental advantages of the cutter soil mixing technique, comparing with same more conventional solutions.1 INTRODUCTIONThe construction of the new Cruise Terminal at Leixões, main gate of the Atlantic Ocean to the North of Portugal and Spain, as a consequence to the constant increase of the cruise traffic, was a challenge from both the geotechnical and structural point of views, mainly due to very difficult and unusual conditions, ranging from the geological and geotechnical scenario to the existent and under operation Leixões Port infrastructures, mainly the South break water, as well as the existent cruising boarding deck (Figure 1).According to the Terminal Project it was necessary to build one basement below the water table level, including several earth retaining structures in order to allow the excavation works on dry conditions leading to a global cofferdam effect. For this purpose soil - cement panels, using CSM technology, reinforced with steel profiles, micropiles (both for foundation and cut off effect) and the existent sheet piles were used. Also pointed out are the adopted special foundations of a very complex structure, including bored piles and micropiles (Figure 1)."

Jan 1, 2015

By Reinaldo J. Villa, Joshua C. Adams

The I-395/SR-836/I-95 reconstruction project is an $818-million design-build construction effort that includes construction of viaduct, segmental and signature bridges in Miami leading into Miami Beach in Florida. Based on the load testing performed during the design phase, the design-build team determined that conventional driven pile and drilled shaft foundations were not feasible for support of segmental and signature bridges. Due to the weak limestone formation and successful use of auger cast-in-place (ACIP) piles in the Downtown Miami area on commercial developments, ACIP piles were selected as a foundation system to support bridges. This is the first time in history where the bridges will be supported by ACIP pile foundations in an interstate highway in the State of Florida. The design build-team worked closely with the Florida Department of Transportation to develop requirements for the load test program. The paper will provide an overview of the geotechnical data collected, results of dynamic/bi-directional load testing performed on test piles, data collected, installation of piles, and lessons learned. The load test program included a total of fifteen test piles with dynamic, bi-directional, and lateral load testing on 30 and 36-inch diameter ACIP piles and instrumented with thermal integrity profiling wires.

Sep 8, 2021

By Ken MacLeod

A development at 83 Queens Road in Melbourne, Australia required construction of a three level basement. The normal geotechnical constraints of excavating adjacent to an existing relatively new building were challenging enough for the complicated soils profile occurring at the site. An additional significant challenge faced by the designers, was the requirement to excavate underneath the entire footprint of an existing heritage listed building, known locally as the Mansion, in the centre of the site. Maintaining the structural integrity of that building was afforded the highest priority during the 10m excavation. This paper describes geotechnical aspects of the analysis, design and construction of the secant retention system adjacent the new building and support of the Mansion enabling the 10m excavation to proceed without causing damage to the structure. The secant wall comprised hard-soft interlocking piles constructed using CFA methods. CFA piles along the length of the Mansion provided short term support, with the building load being transferred to the piles by large steel beams jacked under the building. Survey results confirmed that movements of the retaining wall and also the load bearing piles were minimal and well within design expectations.

Jan 1, 2006

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.