Search Documents

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

By Clyde N. Baker

The paper describes procedures used to predict the settlement performance of drilled shafts constructed under slurry through water bearing deposits to a dense bearing strata, considering both side resistance and end bearing. A full scale instrumented drilled shaft load test on a Jersey City, New Jersey highrise project is used as a case history to compare with prediction.

Jan 1, 1991

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By Brian H. Greene

The U.S. Army Corps of Engineers, Pittsburgh District, is in the final phases of modernizing the locks and dams on the Monongahela River. One facet of this modernization is to replace the existing Locks 4 located on the Monongahela River approximately 40 river miles upstream from Pittsburgh, Pennsylvania. The existing locks consist of a 56-foot x 720-foot main chamber and a riverside 56-foot x 360-foot auxiliary chamber built in the 1930s. Two new lock chambers, each 84-foot wide by 720-foot long, will be constructed at the location of existing Locks 4 and will be named Charleroi Locks. The purpose of the new project is to facilitate navigation on the lower Monongahela River. Pittsburgh is currently the second largest inland waterway port in the nation, and the new locks will be an important component of the navigational infrastructure. The existing lock walls are of mass concrete construction and are founded on wooden timber piles driven to rock through alluvial sands and gravels. The new lock walls were designed to be supported by approximately 300 reinforced concrete drilled shafts, varying in diameter from 4 to 6 feet. To handle axial loads, the drilled shafts were designed for end bearing, with some skin friction. The tips of the shafts will be founded within competent rock. Since the walls will undergo lateral loads, the drilled shaft design also had to consider this loading condition. Some of the drilled shafts will be installed within coffer boxes, which will incorporate a tremie concrete seal down to top of rock. Complicating the design even further was the fact that some portions of the new walls will be supported by shafts that extend some 9 feet above top of rock through alluvial soils, producing a cantilever effect. The first phase of the new lock construction was initiated in the summer of 2005 with a contract awarded to replace the river wall. This required shutting down the existing riverside lock chamber and diverting all river traffic to the longer existing land chamber. The foundation of the new river wall will use 144 drilled shafts. To optimize the design embedment of drilled shafts in rock for the river wall, an exploratory drilling program was conducted by the contractor in July and August, 2005. Based on the quality of the sedimentary bedrock, the shafts will be embedded in rock from 31 to 38 feet. To achieve adequate end bearing resistance, the tips of each shaft will extend through predominantly claystones into a more competent siltstone unit for a minimum embedment of one foot. The contractor also performed an exploratory pile driving program to aid in the construction of the drilled shaft casing and the cut off walls that will encapsulate the river wall. Two demonstration drilled shafts located outside the footprint of the new river wall, will be constructed prior to the drilling of any production shafts. The demonstration drilled shafts will verify that the contractor is able to meet the design criteria and quality requirements of the contract. The river wall contract is currently underway and is scheduled to be completed in 2010.

Jan 1, 2006

By B. M. Das

Several laboratory model test results for the determination of the ultimate uplift capacity of single and group metal piles embedded in near-saturated clay have been presented. Based on the uplift test results for single piles, the variation of the adhesion factor with the undrained shear strength of clay has been determined, and an empirical correlation for estimation of the adhesion factor in soft and medium clays has been presented. The group efficiency of piles under uplifting load depends on factors such as embedment ratio, undrained shear strength of clay, the number of piles in a group, and the center-to-center spacing of the piles.

Jan 1, 2010

By Ahmad F. Souri, Murad Abu-Farsakh

"In this study, the static lateral resistance of vertical and battered pile groups was analyzed using 3D finite element analysis. The battered pile group finite element model was verified using the results from a case study performed on the M19 pier foundation of the I-10 twin span bridge in Louisiana. The vertical pile group model was created by adjusting pile inclinations of the verified battered pile group model. The finite element models utilized nonlinear constitutive models for materials behavior and a soil-pile interface model. The results showed that the battered pile group had greater lateral resistance than the vertical pile group with 60-70% lower pile cap displacement. The largest lateral load share was found in the middle rows in the battered pile group, while it was in the leading row for the vertical. The soil resistance profiles showed that the vertical pile group mobilized greater soil resistance compared to the battered pile group.INTRODUCTIONThe lateral resistance of a pile-soil system depends on both pile stiffness and soil reaction. The soil reaction is a nonlinear function of deflection, depth, pile stiffness, and soil stiffness and strength. The lateral capacity of single piles is evaluated at the maximum deflection limit, and can be predicted using established methods such as the p-y curve method (e.g., Matlock 1970, Reese et al. 1974), elastic solution by Poulos and Davis (1980), the strain wedge model (Ashour et al. 2004), and the finite element method (e.g., Yang and Jeremic 2002, Comodromos and Pitilakis 2005, Isenhower et al. 2014). For pile groups, the lateral capacity of a pile-in-group is less than the isolated single pile case because the soil in front of the pile-in-group is weakened by the overlap of stress zones from surrounding piles. The latter is referred to as the shadowing or group effect (Fig. 1). Prediction of the lateral capacity for pile groups is based on the p-y curve method for single piles with the use of empirical factors called “p-multipliers”. The p-multipliers accounts for the shadowing effect, and are a function of pile-pile spacing and soil type (e.g., Brown et al. 1987, 1988, McVay et al. 1995). Moreover, the lateral capacity of pile groups is also influenced by vertical load, piles arrangement, and slenderness ratio (e.g., Rao et al. 1998, Patra and Pise 2001, Ilyas et al. 2004, Hussien et al. 2012).Battered piles refer to piles installed at an angle with respect to the vertical to increase their lateral capacity. The greater lateral resistance is achieved by the additional axial reaction in the pile. Battered piles are called “negative battered” when inclined in the load direction, and “positive battered” when inclined opposite to the load direction (Fig. 1). Previous studies concluded that the lateral resistance is highest in positive battered piles followed by negative battered and vertical piles, respectively (Murthy 1964, Meyerhof and Yalcin 1993, Zhang et al. 1999)."

Jan 1, 2017

By M. J. Preim

Two case histories are presented on the evaluation of static bearing capacity of piles driven in soils that exhibit time dependent strength changes. Under consideration are a steel and a concrete pile driven into soils generally consisting of silty and clayey fine sand. Pile dynamic measurements and analyses were performed on both piles during initial installation, and also during restrike one week later. This information was used to predict each pile's long term capacity (defined as 14 days after initial drive), which was then compared to that measured with a static load test. Agreement between predicted and measured capacities were remarkably good, with an average error of only 4.5 percent. Two weeks after driving, total pile capacities were three times those at the end of drive. If only the skin friction was considered, however, it increased by an average factor of 16. The increase in pile capacity was determined to be linear over the time period considered.

Jan 1, 1989

By Niels Krebs Ovesen

Close economic cooperation was established among the countries in western Europe during the seventies. As a consequence, among others, a need for harmonized technical specifications for civil engineering works arose. Technical specifications for design and execution of building and civil engineering structures exist in most of the European countries. In some countries such technical specifications are part of the building regulations and in other they are independent codes of practice and standards. The works on the Eurocodes was initiated by the Commission of the European Communities about 1976. The Eurocodes are intended as common unified design codes for different load bearing structures constructed from different materials. They are also intended to cover design of geotechnical structures. They are established with a view to promote the free movement of goods and services within the member states of the European Community - the so called Internal Market - and within the member countries of the European Free Trade Association, EFTA by removing obstacles arising from different rules for calculation and design.

Jan 1, 1994

By Naresh Koirala

The Greater Vancouver Regional District completed installation of a 2.5 Km long, 2400 mm diameter concrete sewer in Delta, British Columbia in 2000. The sewer traverses through area of peat and soft ground. The ground investigation along the sewer alignment consisted of cone penetration tests and auger drilling with standard penetration tests. The gravity sewer is supported on precast, pretensioned spun concrete piles imported from Malaysia which had never been used for a major project in North America. The capacities of the installed piles were tested using pile driving analyzer (PDA) and three static load tests. A total of 46 PDA tests were carried out during pile installation. The paper describes the pile vetting process the owner went through prior to accepting the piles for use in the project and performance of the piles. It compares the pile capacity estimated from the PDA tests with that estimated from soil mechanics methods using data from cone penetration tests and standard penetration tests. The ranges of estimated capacities calculated by different methods are discussed from design capacity selection considerations.

Jan 1, 2004

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Z. Y. Ding

This paper emphasize two points in piled wharf design which are important than structure calculation. First, during design of piled wharf on soft stratum, the bank slope stability is the first important item. Second, the live load, the backfill and the original ground's settlement will influence the wharf structure causes cracks. Two practical examples were illustrated.

Jan 1, 1991

By N. S. Yet

This paper shall present the design and construction of bored pile and diaphragm wall for the proposed MHA complex in Singapore. The work was carried out by L&M Foundation Specialist Pte Ltd and PWD Consultants Pte Ltd was the consultant for this project. A brief description of the project is first presented to illustrate the scope and scale of the work involved, which includes the construction of bored piles and diaphragm walls and installation of steel stanchions in the bored piles. This is followed by a description of the methodology used to analyse and design the wall and bored piles. As both towers in this project are supported on bored piled foundation and are constructed by top down construction method, the analysis of the wall has taken into consideration the sequence of work phase by phase and this was carried out by means of a commercial finite element program called CRISP. Modelling of the problem will be briefly described and the findings from the numerical analysis will be presented. This is followed by a description of the structural and geotechnical design aspects of bored piles. The paper shall then describe the difficulties encountered for this project and solution used to solve the problem. The subsoil condition will be described with special mention on the encounter of very strong granitic rock at depth above the maximum excavation level of the basement at certain locations, hence necessitating the drilling of rock for a considerable depth for both bored piles and diaphragm wall. At this juncture, the construction method used to drill through the rock will be briefly described. For construction of bored piles, penetration of rock was carried out by chiselling or drilling using reverse circulation rigs. For construction of diaphragm wall, it requires the employment of Bauer hard rock cutter which uses cutting wheels fitted with roller bits and are capable of excavating into granitic rock of compressive strengths more than 100 MPa.

Jan 1, 2000

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By A. Frits van Tol, Rodriaan Spruit, Jan H. van Dalen

"Abstract In recent years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse in Singapore the quality of the D-walls was not the cause. However in other projects, like the problems with the major leak in the walls of the Boston Big Dig and with leakage in a few projects in Belgium and The Netherlands was related to poor D-wall quality. Leakage through the D-walls at the joints in deep excavations led in these cases to very serious settlement behind the walls, in the case of the North- South line in Amsterdam, there was severe damage to historical buildings. This paper describes ongoing research that focusses i on acquiring more knowledge on and improvement of D-wall installation, in particular the flow process prior and during casting ii on the detection of anomalies prior to excavation and iii on the composition of the concrete mixture in view of a better and more sustainable concrete quality of D-walls.INTRODUCTIONIn the case of deep excavations in urban areas close to neighbouring buildings, diaphragm walls are one of the best feasible solutions for the retaining structure. Although the costs of D-walls generally exceed the costs of alternative wall solutions, the advantages are decisive in many situations. The main advantages of D-walls are the limited impact of the installation on the built environment, the high stiffness and bearing capacity and the retention of water, even at considerable depths. This makes Dwalls often the preferred solution for deep excavations Sometimes the D-walls are the temporary support while for the final stage a complete concrete box is constructed in the excavation. In many other cases the D-wall has the permanent function of retaining soil as well as groundwater.In the last ten years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse, 2004 , the quality of the Dwalls was not the cause. In other important failures like the collapse of the Archives in Cologne, 2008 and Dubai Infinity Tower Flooding, 2007 a combination of design and quality issues played a role. However, the major leak in the walls of the Boston Big Dig was related to poor D-wall quality (McNichol, 2000). Van Tol et al, (2010) describe a number of case studies in Belgium and the Netherlands, with leakage through the D-walls at stop end joints. In several cases with deep excavations these leakage caused serious surface settlements behind the walls. In the case of the North-South line in Amsterdam, there was severe damage to historical buildings. All these cases have generated considerable additional costs and delays, and subsequently public and political concern. Van Tol et al. (2010) present several possibilities to improve the quality of D-walls.Other disputes related to D-walls deal with the quality of the concrete and the sustainability of D-walls applied as a permanent wall. In particular the porosity of the concrete cover is sometimes problematic."

Jan 1, 2014

By Markus Schönit

Double rotary drilling combines continuous flight auger drilling with a casing for producing a cast-in-place pile. When producing a pile an outer casing and an auger (hollow auger) rotating inside the casing are driven into the ground in counter-rotation. The outer casing serves to support the surrounding soil and the inner auger excavates the drilling cuttings to the surface inside the casing. After reaching the projected drilling depth concrete is pumped through the hollow stem of the auger and outer casing and auger are extracted. After their complete extraction a reinforcement cage can be inserted in the fresh concrete. Compared to Kelly drilling the double rotary drilling method offers numerous advantages, including, for comparable diameter and length, shorter production times and higher accuracy (pile inclination and excess concrete) combined with increased occupational safety and lower noise emissions. Moreover, pile tests have proved that piles produced by double rotary drilling feature higher axial load-bearing capacities than comparable piles produced by Kelly drilling. This article offers an overview of the basic theoretical principles of double rotary drilling lists the required and currently available machinery and, finally, discusses the results and conclusions of a current jobsite.

Jan 1, 2011

By Donald Bruce, Mark Harris, Wesley Schmutzler, James Sanders

"This paper evaluates the history, construction and most importantly the performance of two remedial seepage cutoff walls installed in two major dams in the United States. Beaver Dam, on the White River in northwest Arkansas, was completed in 1966 and seepage through the karstic limestone under the embankment was apparent almost immediately upon filling of the reservoir. Several attempts to stop the seepage by grouting were unsuccessful. In 1994 a cutoff wall consisting of secant piles drilled with 32"" diameter down-the-hole hammers to a maximum depth of 185'?was completed and the seepage was reduced to a negligible amount. It has been over 20 years since the completion of the cutoff wall, and all indications are that the cutoff wall is performing as expected. Walter F. George Lock and Dam on the Chattahoochee River near Fort Gaines, Georgia, was completed in 1963 and suffered the same problem as Beaver Dam due to the limestone on which the dam was founded. Cutoff walls were installed in both embankments (1980s) and solved the problem in these areas, but under-seepage at the concrete lock, dam and spillway structures increased to the point that remediation was essential. The cutoff wall had to be installed through 110'?of water and another 100'?into rock upstream of an active dam that continued to generate electricity during the construction of the cutoff wall. A secant pile wall, in combination with a diaphragm wall, was completed in front of these structures in 2004. It has been over 10 years since the completion this cutoff wall and, again, the cutoff wall is performing as expected. The paper describes the construction of these cutoffs, but focuses on the long-term performance in terms of controlling seepage and piezometric levels.BEAVER DAMBeaver Dam is located on the White River, 609 miles above its mouth, in Carroll County, Northwest Arkansas. The construction of the dam and Beaver Reservoir was authorized on September 1954 by the Congressional Flood Control Act for purposes of water supply, flood control and hydroelectric power generation. The dam site was selected in 1957: construction began in November 1960 and was completed in June 1966. (FIG. 1)"

Jan 1, 2017

By Pan Shisheng

Amodified load transfer method computing the displacement, axial compression, skin resistance, toe resistance, and other static bearing behaviours of piles, is propoesd in this paper. Through deriving a new concrete computational method with simple integration, many complex factors, such as different soil properties of each layer in layered soil, variation of soil parameters with the changes of the depth, different elastic moduli of piles under different loads, and even different areas in the same pile, can all be easily considered. This method fits in with many types of piles, including friction and point bearing piles, precast and cast-in-situ piles. Observation of static loading test on pile is given, and the computed values from the modified load transfer method are found to agree with practical measured results.

Jan 1, 1991

By D. V. Karandikar

Contiguous bored piles have been used in the past for retaining the sides of deep excavation. An innovative version of this method was adopted successfully in two prestigeous projects in Bombay in which in a very constricted and congested locality, adjoining seashore at Walkeshwar, 14 m deep excavations with vertical sides were required. 600 mm dia bored cast-in-situ piles were first installed at 1.2 m c/c and subsequently as the excavation proceeded, they were tied to cast-in-situ RCC waling beams. The shear connectors to the beams were pre-fixed to the pile reinforcing cage at specified depths. The pile / waling beam system was anchored into the ground by installing inclined prestressed cable anchors at the designed depths. The waling beams were also used to support the brickwalls, which formed the required backup wall for fixing the tiled water proofing system. Catch-drains were installed behind the brickwalls for relieving the ground water pressure and thus ensuring a very economic design. The adequacy of the system was proven in that where the system was not installed in time, failure of the sides occurred during monsoon. Whereas in the areas where the above retaining system was installed, there were no problems inspite of heavy monsoon and surcharge of construction materials and equipment. The system became a very effective and economic alternative to an anchored diaphragm wall. The paper presents the case studies of these two projects.

Jan 1, 1996

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

By Satyajit Vaidya, Rudolph Frizzi, Luis Berroteran

This paper presents design and construction challenges associated with a high-capacity rock-socketed drilled pile foundation system for a 60-story building recently constructed in an urban environment. The site is in very close proximity to surrounding 1-to-6-story buildings and a commuter rail subway tunnel structure. High compression, uplift, and lateral loads imposed by the tall, slender tower constructed over a relatively small site footprint posed a significant design challenge due to the close proximity of the subway tunnel and other structures. Construction challenges included those associated with advancing the drilled pile casings through overburden materials using internal flush method mandated by the Transit Agency, advancing the casings through very dense glacial till materials encountered above top of rock, and drilling rock sockets in variable rock conditions. This paper provides a brief overview of the site and subsurface conditions, and discusses the resulting design and construction challenges for the drilled pile foundation system and how they were addressed. SITE AND SUBSURFACE CONDITIONS The 8,350-square-foot site is located in a busy neighborhood in downtown New York City (NYC). Buildings neighboring the site are supported on shallow foundations, and their basements extend about 15 feet below the sidewalk level. A NYC-Landmarked building is located within a NYC Department of Buildings (DOB)-designated 90-foot influence limit from the Project site. NYC Transit Authority (NYCTA) subway tunnel and station structures are located in close proximity to the Project site. The subway tunnel structure extends about 50 to 55 feet below the sidewalk level. Although the upper portion of the tunnel structure is about 13.5 feet away from the site property line, the lower portion is only about 1 foot away from the property line. A site location plan is presented as Fig. 1. Geotechnical borings revealed subsurface conditions generally consisting of successive strata of surficial fill, sandy and silty soils, and glacial till (predominantly consisting of cobbles and boulders) overlying mica schist bedrock. A generalized subsurface profile is presented in Fig. 2. The surficial fill stratum was about 10 to 23 feet thick, and generally consisted of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick. The underlying sandy and silty soil stratum was about 60 to 79 feet thick and generally consisted of loose to medium dense inter-bedded layers of fine to coarse sand, silty fine sand, and silt. The underlying glacial till stratum was about 26 to 70 feet thick and generally consisted of cobbles and boulders embedded in a very dense soil matrix. Top of bedrock was encountered in the borings about 110 to 150 feet below sidewalk level. Groundwater level was measured at about 30 feet below sidewalk level.

Jan 1, 2018