Search Documents

By Henry M. Howe

THIS paper gives the composition of the iron and slag at different stages in the "air-furnace" process of preparing "hard metal," or white cast-iron, for conversion into malleable cast-iron by annealing. The details of the process are given in an appendix. One of us had been trying for years to work some chemist of some of our malleable-iron works up to a degree of enthusiasm which would lead him to make such au investigation. It would have had the advantage of the greater familiarity with the conditions which one habitually on the spot must have. Failing in this, he made use of an opportunity which presented itself of taking samples here represented, with such fairness as the conditions permitted, holding firmly that a rough approximation to the truth is better than the complete lack of data, or that a bird in the hand is worth two in the bush. We hope that this attempt may stimulate others effectively to duplicate this work, and thus correct or confirm it. Our results are shown in Table I. and graphically in Figs. 1 and 2. Discussion.-At the time when the first two samples were taken, the metal and slag were still too sluggish to permit fair sampling, and not until sample 6 were the conditions really favorable, because at the time of the fourth sample the metal was not fully melted, and even at the time of sample 5 it was still sluggish. Indeed, the slag was probably very heterogeneous throughout, because it took up silica and alumina rapidly from the bottom, and because it was so siliceous as to be sluggish at this relatively low temperature. This hetero-geneousness is exaggerated in the two samples of slag 8, apparently by the great viscosity due to its extraordinary acidity. Note that the manganous oxide of one sample is about two and

Mar 1, 1909

By C. E. MacQuigg

MAN?S desire to harden metal is older than recorded history and obviously would date from the moment when he found his implements were not equal to the demands of service. This need for hardness in metal may be divided roughly into two main classifications: (1 :I need for hardness through- out-for purposes of greater strength or elasticity of the whole implement or member, and (2) need for surface hardness alone. A strong steel needed to transmit stresses or resist de- formation is an example of the first class. In metals only surface- hardened, the chief need is for resistance to wear. Obviously the whole gamut of all uses can be imagined- from the extreme of a simple cantilever supporting a load in space to that of a solidly supported face plate serving to resist wear. It is the in- creasing of wear resistance which I propose to discuss.

Jan 1, 1939

By Jay J. Burns

TWO zinc concentrating mills are operated by the St. Joseph Lead Co. in St. Lawrence County, N. Y. The Edwards mill is operating at present only sixteen hours a day treating 400 tons daily. The metallurgy at Edwards presents no unusual problems therefore this discussion is mainly limited to the metallurgy of the Balmat ore. The Balmat mill has a capacity of 1,250 tons per day and the operating crew consists of three shift bosses each with five millmen per shift. Two crusher operators work on each of two shifts and one cleanup man on day shift. The repair crew is made up of a foreman and three repairmen, one of the repairmen being capable of taking over any operating job in the mill from shift boss down. Each millman is capable of handling the next job in line and several men in the yard crew are broken into handling the start-off job in the mill so that temporary shortages of men do not cause extensive overtime. Sphalerite, pyrite, and galena, the principal ore minerals, occur in a gangue of calcite, dolomite, and silicates, especially diopside, plus tremo-

Jan 1, 1947

By Charles Austin

IT has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent C0 and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their pro-portional limits and yield points are rela-tively low. Published data1 for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the results shown in the lower section of Fig. I. TABLE I.-Analysis of Material I Percentages Constituent Sample Sample Sample 3125 3124 3123 Si 0.25 0.51 o.6o Fe 4.15 10.70 13.17 Ti I.15 3.58 4.70 Mn 0.30 0.41 0.42 Co (by difference)^ 94.15 84.80 81.71 The cobalt from all three samples, united and tested for nickel, gave 0.54 per cent Ni based on the weight of cobalt. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deforma- tion characteristics in moderately long-time tests at 600°, 700° and 800°C. after quenching from various solution tempera-tures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain in- FIG. 1.-EFFECT OF VARYING AMOUNTS OF FERROTITANIUM (FE2TI) ON PHYSICAL PROPER-TIES OF COMMERCIAL COBALT. (C. R. Austin.1) Upper section. Tested at 600°C. after water-quenching from 950°C. Lower section. Tested at 600°C. after water-quenching from 950°C. and aging 72 hr. at 650°C. FIG. 2.-PORTION OF QUASI-BINARY DIAGRAM COBALT-FE2TI AS DETERMINED METALLOGRAPH-ICALLY. formation on the quasi-binary system Cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufac-turing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table I. The alloys, when originally made up,1 were based upon an iron-titanium com-pound, Fe3Ti, as indicated by the work of

Jan 1, 1940

Adams . Bernard . Student. South Dakota School of Mines .Rapid City . S . D . Ahlskog . Harold A. Student. Washington State College Pullman. Wash . Aldridge. John. Student. New Mexico School of Mines Socorro. N . M . Almstrom . Adne A .. Student. Met . Engrs.. Washington State College ..... .Pullman. Wash . Ancell . Virgil F.. Student. Missouri School of Mines Rolla. Mo . AnkudinoE. N., Mill Draftsman. Arthur G . McKee & Ch., 2422 Euclid Ave., Cleveland. Ohio . Avablaea . Salvador C.. Student. Univ. of California Los Angeles. Cal. Armstrong. Robert E .. Student. Lafayette College .Easton. P a Armstrong . Thomas E.. Student. Univ . of California Los Angela. Cal Aud. Robert A .. Student. Lafayette College Easton. Pa .

Jan 1, 1929

By R. G. Lazzell

THE British are worried about the postwar possibilities of their coal mining industry. Indeed, there are causes for this worry, with the aver- age 1943 cost of production at about $5.40 per long ton, compared to $3.20 in 1938. Average production per man day has dropped from 1.12 in 1938 to 1.03 long tons in 1943. As a comparison, production per man day in the United States is approximately 5 long tons. The average day wage in the British mines is now a little aver $4; in 1938 the average day wage was about $2.25. Great Britain produced 227 million long tons in 1938 from their deep mines, and in 1943 production was 194.5 million, with an additional 4.5 million from strip mines. To meet present wartime needs, output is being supplemented by the production of strip- mined coal, an industry that did not exist prior to the war. Strip mining is now producing at the rate of 15 million long tons per year.

Jan 1, 1944

By N. O. Gray, John Henderson

Hydrogen-reduction data for naturally occurring single crystals and Prepared polycrystals of dense hematite have been presented. Results cover the temperature range 400o to 1000oC, for particles from ten sources, ranging in size from 0.07 to 10 mm and in shape from spheres to cylinders, cubes, and thin slabs. A consistent pattern of behavior has been demonstrated for single crystals and the reduction mechanism shown to be temperature-dependent. Below 579oC reduction is a simple topochemical process but at higher temperatuves it is complex and occurs in two distinct stages. Prepared particles from these laboratories behave in a similar manner to the single crystals. Data from two investigators showing topochernical reduction of Prepared particles above 575°C are inconsistent with that for other dense hematites. It is concluded that topochenzical reaction should not be used as a model for generalized rate expressions for dense hematites. SINCE 1958, McKewan1-6 has brought to prominence a simple concept of dense hematite reduction. This model is that oxygen is lost from a hematite particle undergoing reduction only from an oxide-iron interface that recedes in such a way that the oxide remaining retains the original shape of the particle, i.e., reduction occurs topochemically. An adjunct to this concept is that any intermediate oxides in the transition from hematite to iron only form thin layers so that oxygen cannot be lost from the particle without movement of the oxide-iron interface. Further, the rate of oxygen loss from the particle is said to be proportional to the area of the receding interface so that the iron layer grows linearly with time and the over-all reduction process can be described by the equation where ro and do are the initial particle radius and density, respectively, R is the fraction of the original oxygen lost, i.e., the fractional reduction, at time t, and K is the rate constant. The idea of an underlying simplicity in hematite reduction is attractive because it gives a tractable basis from which general theories of hematite reduction can be developed and it has received wide support,7-14 based mainly on the large amount of data13 that can be fitted to Eq. [I]. However, despite the fact that this equation has been derived for dense materials, the bulk of the data that have been used to test it13 have been for materials of only about 90 pct of theoretical density (5.26 g cm-3) or less, so that its generality for dense hematites has not been demonstrated. In any case, as will be seen, adherence of reduction data to Eq. [1] does not necessarily imply that reaction occurs topochemically. In this work only data for hematites approaching theoretical density are considered and it will be shown that in only one study besides McKewan's is topochemical behavior observed over the whole range of temperature investigated. For the majority of materials a linear rate of interface advance is observed to complete reduction only when wustite is not a stable intermediate phase in the transition of hematite to iron, i.e., at temperatures below about 575°C. Above this temperature, reduction is an exceedingly complex series of reactions that takes place in two distinct stages and it is only in the first stage that reaction in any way resembles a topochemical process. This means then that, far from representing general behavior as has commonly been supposed, topochemical reaction for dense hematites is only a particular behavior that may be observed under some circumstances. EXPERIMENTAL Hydrogen-reduction data have been collected and cross-checked in these laboratories by three techniques, weight loss, collection of water evolved in the reduction reactions, and direct metallographic examination. Details of these techniques are discussed elsewhere," where it is shown that results obtained by the three methods are in close agreement. The weight-loss method, by which most of the results were obtained, consisted of hanging the sample in a platinum mesh basket from an Ainsworth Model AV-AU-1 vacuum recording balance inside a vertical l 1/4-in.-ID alumina tube furnace. Dry deoxidized hydrogen was flowed downwards through the tube at 2 to 4 liters min-1 (stp). Single crystals from two sources and artificial oxides from three sources have been examined. The single crystals were from hematite deposits at Yampi Sound, Western Australia, and Brazil, the latter being obtained from Gregory, Bottley and Co., London, U.K. The "Yampi Blue" crystals were hand-picked from washed, magnetically concentrated, sized fractions, -200 mesh BSS (mean diameter ca 0.07 mm) and —36 + 44 mesh BSS (mean diameter ca 0.4 mm) while 10-mm cubes were cut from the Brazilian crystals with a diamond saw. The starting materials for the prepared particles were hematites designated, respectively, "Specpure Iron Oxide", Laboratory No. S639 from Johnson Matthey & Co. Ltd., London, U.K., "Calcined Ferric Oxide" from B.D.H. Laboratory Chemicals Division, Poole, U.K., and "Pigment Grade Oxide", EPR-50, from C. K. Williams & Co., Easton, Pa., U.S.A. Approximately spherical particles were prepared from the artificial oxides by rolling the material, moistened if necessary, in a glass jar, and cylindrical compacts approximately 10 mm in diam and of approximately equal height were pressed in a steel die at 200 psi. These spheres and cylinders were subsequently fired in oxygen for 20 to 100 hr at 1370°C. The

Jan 1, 1967

By G. A. Beske, P. Hilsch, J. Wulff

The effects of the growth precipitates on the su-perconduching properties of an Al- 15 al. pel Zu alloy have been studied using magneization, transition lem-perature, and residual resistivity measurements. Aging at 230C for 1/2 to 11 he produces an increase in Hfp, Ike field of first penetration, and tut increase in trapped flux. The upper critical field, Hc2 remains constant for such aging tunes. Aging at 200°C produces a decrease in Hfp and an increase in trapped flux. The transition temperature remains constant at Tc - 1.227° ± 0.02°K for aging at 220°C for tims of from 1/2 to 10 hr, and for aging at 200°C it remains constant at Tc. = 1.18° i 0.02°K for times from 1/2 hv to 26 hr. The observed behavior indicates that the superconducting matrix when aged at 220°C behaves tike a type U su-perconducior, but when aged at 200°C behares like a type I superconductor. The magnetization changes after aging can be attributed to the growth and clutnge in distribution of the precipitate in a matrix of fixed composition. IT has been realized for some time that the superconducting properties of alloys are highly structure-sensitive. This is evident in the work of Mould and Mapother1 who examined the properties of an aluminum alloy. Precipitation effects have also been briefly mentioned in other studies.2-4 Bonnin and coworkers5 have observed a sharp inc rease in trapped flux in an A1-Mg alloy when the residual resistivity reaches a value that indicates it is a type II superconductor. Recently Blanc, Goodman, and Nemoz5p have reported on precipitation effects in A1-Ag alloys. Detailed studies of precipitation in Pb-Sn and Pb-Cd alloys made by Livingston6 serve to show that the upper critical fields are enhanced by quenched-in solute. Furthermore. at various stages in the precipitation process? the upper critical field is determined largely by the remanent solute. The observed magnetic hysteresis and trapped flux in such alloys result from the interaction between precipitate and the flux filaments in the mixed state. The flux trapping appears to depend largely on the precipitate distribution and is greater if the superconductor is type II than if it is type I. To examine the effect of precipitation in another alloy system, particularly one in which the composition of the superconducting phase does not change significantly during the course of precipitation, the Al-Zn system seems interesting, especially in view of the transition temperature and resistivity studies of Chiou and seraphim.' Furthermore, the recent detailed electron-microscope studies of an Al-Zn alloy by Richards and Garwood8 provide a guide for relating superconducting properties to changes in structure. For these reasons, magnetization, transition temperature, and residual resistivity measurements for varying times of heat treatment at two temperatures were made with a -15 at. pct Al-Zn alloy. The results are reported in this paper. I) EXPERIMENTAL The alloy used was prepared by Cominco Products Inc. from 99.9999 A1 and 99.999 Zn. It was chill-cast, swaged, and drawn to 0.125-in.-diam rod. The analyzed composition was 15.6 at. pct Zn (31.1 wt pct). A jeweler's saw was used to cut the 0.125-in.-diam rod into the 0.875-in. lengths needed for magnetization measurements. The ends of the cylinders were slightly beveled to remove the sharp edges. A portion of the original 0.125-in.-diam rod was drawn into 0.010-in.-diam wire and used for transition temperature measurements. Specimens were suspended from wires within a vertical furnace during heat treatment. All were homogenized at 500°C for a minimum of 3 days and subsequently solutionized for times in excess of 6 hr. The solutionizing temperature was held constant to +3°C. Individual specimens were homogenized, quenched, and aged several times and no effects indicating loss of zinc were noted. The suspended specimens were quenched by cutting the wires and allowing the specimens to fall into a silicone oil bath held at the aging temperature. They were then isothermally transforked by aging in the same bath used for quenching. After aging for the required time (approximately 10 min aging was necessary before the upper critical field reached a fixed value), they were briefly (1 to 2 sec) dipped into an acetone bath at room temperature to remove adherent oil and then immediately transferred to liquid nitrogen where they remained until inserted into the helium bath (usually within an hour). The temperature of the aging bath was held constant to +3°C for longer aging times. The cryostat used for the measurement of superconducting properties consisted of outer and inner dewars for liquid nitrogen and liquid helium, Stokes 6-in. booster diffusion pump and Stokes Model 212 mechanical pump, temperature controller to measure and control the temperature of the helium bath, and a superconducting solenoid with inserted search coils to provide the magnetic field and measure the magnetic moment of the specimens. A schematic diagram of the cryostat is shown in Fig. 1. An ultimate temperature of 0.85°K was reached with this apparatus. The temperature controller used is similar to the one described by Blake and chase.' A 0.5 pct Allen-Bradley carbon resistor and a nichronle heater (200

Jan 1, 1968

By A. H. Tousley

Current problems in the cement industry are discussed and suggestions for solving them by modernization are made. Cement facility modernization is discussed in considerable detail with examples illustrating before and after conditions. Itemized are the improvements realized in better working conditions, better efficiency, higher production, lower costs, and better community relations. These improvements are related to the overall profitability of the particular plant or facility.

Jan 1, 1972

June was the month in which AIME was founded in the year of 1871. For some reason, February was selected as the month for the legal Annual Meeting. One can't help thinking wistfully of Annual Meetings in June but of course this is not the reality. Because the Centennial Ceremonies are taking place in February, that month has been chosen as the one in which MINING ENGINEERING, the monthly magazine of the Society of Mining Engineers, a constituent society of AIME, is publishing its Commemorative is- sue to celebrate the event. SME and ME take a proprietary air about AIME. This is mostly because AIME started as the American Institute of Mining Engineers. Metallurgy was added to the name in 1919 and Petroleum in 1956. The official abbreviation of "AIME" has been retained, however.

Jan 1, 1971

By C. S. Barrett

WhEN a collimated beam of protons or other energetic particles is scattered by a single crystal, the emerging particles produce patterns that contain much crystallographic information. Calculations of the trajectories of individual particles can predict with reasonable accuracy the complete pattern (which is related reciprocally to channeling, now studied in detail6) but the task is a lengthy one which has been completed for very few cases. A many-beam dynamic diffraction calculation of the patterns would be even more difficult and in some cases may be invalid. Because of these complexities, simple methods that will predict to a rough approximation the relative intensities of the lines in films of the back-scattering patterns of a given crystal are wanted. I have found a method which, although it is not a valid computation of intensities or of film darkening by either dynamic or kinematic diffraction principles or by trajectory calculations, nevertheless is found to be useful in practice. It has been tested on several crystal types,7 and is here tested on additional ones. The method consists in first calculating the structure factor F(hk1) for the (hkl) plane, of spacing d, by the familiar equation: where the summation extends over the atoms in the unit cell and fj is the atom scattering factor of the jth atom (using tables computed for electron diffraction, preferably those computed without exchange). Then the F values are squared and summed over all the orders, n, for which F2 has an appreciable value, giving a quantity: Finally, I, is expressed as a percentage of Ic for the

Jan 1, 1970

By Charles F. King

THE only investigations on record of the reactions occurring during the Bessemer blow are of charges containing a large percentage of manganese, with the exception of two partial analyses by Snelus and Barker of the. English method, where a low percentage of manganese was used. They do not give the analysis of the spiegel, nor do they report any graphitic carbon after the first stage of the process. Both report only traces of manganese after the first stage until the addition of spiegel. The slags corresponding to the samples of metal were not analyzed.

Jan 1, 1881

By Arthur A. Center

WAR demand- motivated developments in the zinc industry during 1942. Stocks of Prime Western were built up and High-Grade remained tight. The Prince The Prime Western stocks are expected to be cut down and the demand for High-Grade more easily filled as the Depue reflux plant of the New Jersery Zinc Co. increases - production. Subistition of steel for brass in artillery shell cases will have a considerable effect on the zinc situation of the country one estimate of the saving in zinc in 1943 by this substitution being a little under 100,000 ton, of metal. The metal saved will, of course be High-Grade. If the substitution occurs, the present tight situation in High-Grade may be entirely relieved as new production comes on the market and zinc may find itself approaching a situation as comfortable as that of lead provided the supply of zinc-hearing raw materials is sufficient to keep all reduction plants tip to capacity production. The premium price of the per pound of zinc over set quotas which went into effect early in 1942, helped to bring about the new lead-slag-fuming plant and other new sources of raw materials.

Jan 1, 1943

By R. S. Dean

REQUIREMENTS for war materials have led to large scale experimentation upon metallurgical innovations. It is of interest to inquire what this may contribute of permanent value to our existing technology, as innovations adopted during war are apt to be discarded promptly at its end. This is because utilization of substandard ores usually requires a new technology for ore treatment, and a new use-pattern for employment of the products. Thus two very different problems are involved: first, devising a process; then, adopting its products by industry, with readjustments of the use-pattern if necessary. A new process may be as good or better than an old one, but the readjustments required for use of its products may prevent its general adoption if this implies scrapping existing plants and investing much additional capital. Metallurgical innovations are of three kinds: I. The use of substandard material in processes already established; 2. The grading-up of substandard material to render it more suitable for established processes; 3. The adjustment of technology and use-pattern to the raw materials that we have.

Jan 1, 1945

By WILLIAM BOWIE

THE development of the isostatic idea during the last century would make an interesting paper in itself. But the various steps in the development have been covered in a number of papers and books which are readily available. Therefore this short paper should not give space to. the historical phases of the subject. Isostasy is really an old idea, but it is only in the last few decades that it has taken on any great prominence or importance in the study of earth phenomena. It is really remarkable how closely Dutton' sensed the isostatic principle 40 years or more ago. His general principles of isostasy as outlined by him have stood the test of time and fit in closely with the general ideas held today. It would seem, however, that some of his views with regard to the application of isostasy to geological processes must be modified or abandoned.

Jan 1, 1930

By Zárate G. E.

Practical and statistical considerations concerned with the sampling, sample preparation and chemical analysis of precious metal ores are reviewed. The principal requirements related with the characteristics of sample cutter, sample preparation, equipment and methods are discussed. The main errors introduced in the different stages of the sampling systems are defined. The application of statistical techniques to evaluate these errors to determine the ore grade variation and to design the number of increments needed to get an accurate assay are presented. Finally, results obtained with the application of this method to gold and silver ores are analyzed and some recommendations are given.

Jan 1, 1984

By Kingman, Robert I.

SUFFICIENT testing has been .performed with the Dutch State Mines Cyclone for thickening and desliming flotation feed at the concentrator of the National Lead Co., Tahawus, N. Y., to prove its application for this work. It is the purpose of this article to present some of the test results, operational details and advantages of cyclone thickening and classification. The metallurgy of the mill operation was described by Frank R. Milliken, assistant manager of the titanium division.

Jan 1, 1950

C. Edward Stafford, Chester, Pa.:—Doring all my business life, I have been engaged in the manufacture of Bessemer and open-hearth steels, but, during my long connection with the Shoenberger Steel Co. of Pittsburg, I had some experience in the manufacture of high-grade puddled iron for horseshoes, and in making, by Dr. Otto Wuth's process, extremely pure, low-phosphorus puddled blooms (analyzing from 0.005 to 0.01 per cent. of phosphorus and sulphur), which were melted with low-phosphorus pig-iron in acid open-hearth furnaces, to make extra locomotive fire-box steel. I have also seen the Danks puddlers in operation at different times and places, notably where they were most successful, at the Otis Steel Works, Cleveland, Ohio; then under the management of our friend, Mr. S. T. Wellman. These Danks blooms were made solely for open-hearth melting-stock, to which they were well adapted. (The unavoidable presence of bits of ore-fix imbedded in the mass of the metal always prevents the profitable manufacture of merchant iron from Danks' blooms.) With the experience just described, I was to some degree in position to value fairly the means, methods and results of Mr. Roe's mechanical puddling from the metallurgical or technical and economic points of view, when given an opportunity by Mr. Roe to see his puddling-furnace or machine in operation in Pottstown, Pa. Briefly, the furnace, with water-cooled bottom, is rectangular in plan, about 20 by 8 ft. in the clear, suspended by trunnions at the middle of the long sides, at a height of 17 or 18 ft. above the general level. The oscillation (65" each way from the vertical) is accomplished by geared segments (attached to the downward-projecting side or trunnion-plates) with which engage pinions driven by a reversing engine. The whole section

Jan 1, 1906

By H. Rees

This paper supplements and brings up to date a report prepared earlier this year and presented at the Eleventh Pan American Railway Congress in Mexico City. Most of the original report is contained in this paper in order to acquaint the reader with the project background. On December 1, 1961, construction of this locomotive was completed. Stationary testing started immediately, and a host of problems in various areas were uncovered. Many of these had no relation to the use of coal in a direct fired gas turbine. All of them emphasized the problems which plagued previous projects of this kind. In 1944 the Locomotive Development Committee of Bituminous Coal Research, Inc., was formed to study the problems of combustion, coal handling, and fly ash removal which would have to be solved before coal could be used to fire a gas turbine. By 1947 this committee was composed of the chief executive officers of nine eastern railroads and five eastern coal companies. All of the members of this committee were vitally concerned in a coal fired gas turbine because coal cost only one-fourth as much per heat unit as fuel oil. A number of research projects were started to develop and test components on a small scale. This included work at John Hopkins University, Battelle Memorial Institute, Institute of Gas Technology at Chicago, Purdue University, and Southern Research Institute. By 1946 a pilot plant had been installed at the Dunkirk, New York plant of Alco Products Div. of American Locomotive Co. The U. S. Bureau of Mines made available to the Locomotive Development Committee (hereafter called LDC) a Houdry process gas turbine plant, originally destined for a Russian oil refinery. The full scale pilot plant was used to evaluate the results obtained from the small scale studies under actual gas turbine conditions. Operation of this plant disclosed a number of problems which had not been discovered in the small scale tests. By 1951 four 250 hr tests had been conducted with the Houdry gas turbine to test out a variety of equipment. The major problem concerned the removal of abrasive fly ash from the products of combustion so that wear on turbine blades would not be excessive. The first 250 hr test showed that the original fly ash separating equipment was inadequate. Large ash particles passing through the turbine blading were nicking the leading edges of the first row blades. At the conclusion of the second 250 hr test, erosion was so severe that the first row of stator and the first row of rotor blades were replaced. At the end of the third 250 hr test, it was necessary to replace the first three rows of stator blading. The fourth test was used to test out a new design fly ash separator developed by LDC and named the Dunlab tube. This device gave more encouraging results than any of the others tested. Early enthusiasm for overcoming major difficulties had resulted in placing an order in 1946 with Allis-Chalmers Mfg. Co. for a 3750 hp regenerative gas turbine. The gas turbine, together with associated combustion and ash removal equipment, coal handling equipment, generators and gear reduction unit was installed at Dunkirk by 1951. A 750 hr test was made in 1952 with the LDC-Allis Chalmers gas turbine power plant. At the end of this test it was necessary to replace the first four rows of both rotor and stator blading. Rows 5 and 6 did not require replacement. In 1953 the American Locomotive Co. joined with LDC and assumed an active role in equipment development and manufacture. During 1954 LDC-Alco operated the rebladed gas turbine 300 hr to determine if a new fly ash separator was adequate. Performance of the improved separator was considerably better, but trouble was experienced with clogged blowdown lines from the Dunlab tubes. When these lines clogged it permitted the passage of abrasive particles. In 1955 a total of 1421 hr was run. This included 243 hr of cycle operation on Union Pacific coal from the D. O. Clark mine at Superior, Wyoming. During the 243 hr a total of 370 tons of coal was consumed. The purpose of this test was to determine if U.P. coal was suitable for use in a coal fired turbine. It was the unofficial opinion that it was as good or better than the eastern coals that had been tested.

Jan 1, 1964

By E. H. Griswold

PETROLEUM production engineering is essentially the application of the laws of 'physics and mechanics to the production of oil. A true production engineer is one who can apply the principles of mechanics, hydraulics, thermodynamics, and other physical arts so as to facilitate' the efficient and economical recovery of oil. To this end he must have wide knowledge of practical field operations and a working knowledge of geology, with a thorough understanding of the underground state of the fluids which he seeks to control. Generally speaking, there have been two schools of production engineering, the California development and the Mid-Continent development. In California the preliminary production engineering was done by representatives of the U. S. Bureau of Mines and the State Mining Bureau, and was essentially subsurface work in regard to casing patterns, water shut-offs, and completion procedure, inasmuch as these were problems of the utmost immediate importance to the California industry. The oil companies were impressed with the value of such work and placed engineers, or more strictly speaking, engineering geologists on their field staffs. These men, realizing the need of further technical study in the mechanical phases of producing operations, added mechanical and mining engineers, and out of the blend developed what is now known as a production engineer.

Jan 1, 1932