Search Documents

By Chonghun Han, Tae-Hwa Choi, Young-Hwan Chu

"A statistical optimization method is proposed to maintain stable operation in a blast furnace with stave coolers. The objective of this study is to find the operating condition which maximizes productivity as well as minimizes the heat load on the stave coolers. In this method, we first analyzed historical data and calculated the heat flux of stave coolers and the burden distribution by mathematical models. In this approach, we determined the variables to optimize and manipulated variables to adjust these response variables. Next, we collected the necessary data for the data variables after preprocessing such as removal of noise and outlier. Finally, we constructed empirical models describing the patterns of response variables in terms of manipulated variables by partial least squares regression method, and then these models were used as objective functions for entire optimization problem. By using appropriate optimization algorithm, we determined the compromised optimum operating condition considering all response variables from the past operating conditions.IntroductionBlast furnace operation which is accompanied by complex physical and chemical phenomena is an essential process for steel industry. In this process, iron ore which is charged into the blast furnace from the top goes downward. It is reduced to iron by CO gas and is melted by the heat of combustion of coke and pulverized coal. The pig iron is tapped at the bottom in liquid phase after removing the slag, which floats on the pig iron.The cooling equipment of the blast furnace wall is changed from the plate type to the stave cooler recently. In order to cool the shell uniformly and eliminate shell spray cooling, Pohang No.2 blast furnace of POSCO (Pohang Iron & Steel Company) was equipped with 11 rows of stave coolers. These staves are only 350mm-thick including the 170 mm-deep refractory on the hot face."

Jan 1, 2001

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By Yury Kapelyushin

Formation of cementite in the reduction of hematite by CO–CO2 gas was studied in situ using high temperature XRD (HT XRD) analysis. Reduction of hematite was examined in the temperature range 873–1173 K by CO–CO2 gas mixture with high carbon activity. When carbon activity in the system was 1.5, cementite was formed only at 1023 K; it was not observed in experiments at 973, 1073 and 1123 K. Formation of cementite was observed at 923–1073 K when carbon activity increased to 3–5; and at 873 K when carbon activity was 10. Formation of cementite at 973–1073 K proceeded through metallic iron; however, in the reduction of hematite at 873 and 923 K, iron was not observed; cementite apparently was formed directly from wüstite. XRD spectra were used to estimate concentration of carbon in austenite in the process of cementite fromation.

By S. N. Monteiro, C. M. F. Vieira, A. P. N. M. de Sa, J. P. D. Vitorino

"This work has as its objective to characterize an ash waste and to evaluate its incorporation into a clay to produce bricks and roofing tiles. The waste is a type of fly-ash resulting from the incineration of a selected part of urban garbage, which is basically constituted of organic matter and plastics. The waste was submitted to mineralogical and chemical characterization. Compositions were prepared with incorporation of the waste in amounts of up to 20wt.% into athe clay. Rectangular specimens were prepared by extrusion and fired in a laboratory furnace at 900°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste is predominantly composed of quartz and calcium compounds. The incorporation of the ash was deleterious to the evaluated properties of the clay. It is suggested that the incorporation should be made in amounts below 5wt. % to avoid deleterious effect in the mechanical strength and water absorption of the clayey ceramic.IntroductionThe world attention has turned to a subject of great concern today, the production and disposal of large amounts of industrial wastes as well as wastes of various sources. When deposed in an unsuitable place, these wastes can cause considerable harm to human health and to the environment. Our planet suffers with air pollution, groundwater and soil contamination as well as silting of rivers and lakes with the growing amounts of our society wastes.The recycling of waste materials is of great interest to the industries, mainly due to the environmental agencies legislation. One of the practices for correct disposal of these wastes being investigated is to incorporate into red ceramics, such as bricks and roofing tiles. The natural variability of the characteristics of the clays associated with the relatively simple processing techniques and also the low performance required for the products allow the presence of relatively high levels of impurities in clayey ceramics."

Jan 1, 2011

By Masaki Imamura

A novel hydrometallurgical process for copper concentrate treatment has been developed by Niihama Research Laboratories of Sumitomo Metal Mining Co., Ltd. The process has numerous advantages with respect to the operational and environmental aspects. For example, copper is leached effectively from chalcopyrite concentrates by chlorine gas under atmospheric pressure. The copper in the leach solution is then separated from iron and silver by solvent extraction and undergoes electrowinning for its recovery as a highly pure copper metal; this does not require any further purification. Moreover, iron metal can be produced from the purified raffinate by electrowinning without generating a large volume of goethite or hematite, which are solid wastes generated due to iron rejection in common hydrometallurgical processes. This process can also realize the efficient recovery of precious metals. The results of batch testing and continuous-operation testing are presented in this paper.

Jan 1, 2006

By Esher Hsu

In Taiwan, around 8,000 tons of batteries are consumed per year but only 17% of which were collected and transported to oversea for recovery. The dumping used batteries have become a potential environment problem. How to increase the collection efficiency of used batteries is an important issue for EPA in Taiwan. Besides, some treatment plants are on process to get permission for recovering used batteries. The objective of this study is to estimate the recycling cost of spent consumer battery and explore the feasibility of recovering used consumer batteries in Taiwan based upon the principle of cost-efficiency. The recycling cost including collection cost and recovery is estimated based on a survey. Results would provide some suggestions to Taiwan EPA regarding feasibility of recovering used batteries in Taiwan.

Jan 1, 2006

By Peter Woodall, Paul Telford, Pengfu Tan

"Arsenic enters the Mount Isa copper circuit in the form of arsenic rich minerals in concentrates from both the Mount Isa and Ernest Henry copper mines. Arsenic is a volatile metal, and will partition in the copper smelter between smelter off gases, slag and anode. Most of the volatile arsenic will report to Isasmelt Electrostatic Precipitator (ESP) or Waste Heat Boiler dusts where it will form a re-circulating load within the smelter. ESP dust is produced at a rate of 15,000 - 20,000 t/y and is currently removed from the precipitator and leached in the new ESP Dust Recovery Plant to separate copper and arsenic from the ESP dust. This paper describes the laboratory test works of ESP dust leaching, neutralisation and cementation processes. The planttrial, commissioning and operation have been presented as well.1. IntroductionThe flue dusts generated in the process of copper smelting contain appreciable amounts of copper and other valuable metals including precious metals. These flue dusts also contain appreciable amounts of arsenic trioxide where arsenic occurs in the ore body. The copper smelters processing concentrates generate residuals, such as ESP dust, containing arsenic trioxide. ESP dust contains impurities such as arsenic and bismuth which are harmful to the copper refining process if they report to anode. These impurities are fumed off in the smelting process and report to the dust as arsenic and bismuth oxides.The content of arsenic in the feed of Mount Isa copper smelter is about 0.1 % to 0.4%. Arsenic is a volatile metal, and will partition in the copper smelter between off gases and anode. Most of the volatile arsenic reports to Electrostatic Precipitator (ESP) and Waste Heat Boiler dusts where it will form a re-circulating load within Mount Isa Copper Smelter. Unless arsenic is bled from the smelter circuit, it will build up to a point where both anode quality and smelter hygiene are adversely impacted."

Jan 1, 2011

By A. Mukhopadhyay

Gas stirring, simultaneous arcing, chemical additions are some basic steps in the secondary steel making. From tap to team however, there are enough uncertainties and several in-situ decision making required to match the fmal composition and temperature in the given amount of processing time. Currently available control algorithms rely on overall material and heat balance coupled with a self-learning regression based tuning of model constants. In this paper we demonstrate the capabilities of Computational Fluid Dynamics (CFD) in modeling and analyzing the thermo-chemical aspects of secondary Steelmaking. These models take advantage of scientific and engineering advances in computational tools and provide almost real time speed of analysis. This can be a very effective tool for operator training, process debugging and improvement as well as new innovations. Keywords: Argon purging, Secondary steelmaking, Arcing, Ladle Furnace, Process Control.

Jan 1, 2003

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By R. M. Sweetin

Detailed descriptions by operating area of the Kidd copper smelter are presented, together with accounts of complement staffing, training, and preparation activities for smelter start-up in June 1981. Concentrate tonnages smelted in the first twelve months of operation were constrained by the capacity of the furnace off-gas system. However, modifications designed and introduced over that period, plus sustained efforts by operations and maintenance personnel have resulted in stepwise improvements in smelter performance.. Consistent operation at design feed rates has been well demonstrated over the third and fourth smelter campaigns and efforts continue on further improving the continuous smelter on-line times and increasing campaign life. In November 1982., following a seventeen month preproduction period, the Kidd smelter attained full operating status.

Jan 1, 1983

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By R Bartlett

Process engineering-science originally developed for percolation leaching of ore in heaps is extended to the decontamination of unsaturated soil, either in situ or after excavation and emplacement as a soil heap on an impervious pad. Phenomena considered include: soil matrix porosity and permeability; percolating solution retention, capillarity and flow; washing sweep efficiency; optimum solution application rates during leaching; soil agglomeration to improve soil permeability and soluble contaminant transport by diffusion in soil agglomerates. Practical aspects briefly discussed include leach pad construction, solution distribution and recovery from the soil, and solution containment.

Jan 1, 1994

Conventional ferronickel smelting has five main steps: Drying, calcination, prereduction, smelting and refining. In the scope of the current work, smelting experiments were conducted using Sivrihisar laterite ores (1.26% Ni) of Turkey. The ore samples previously subjected to drying, calcination and prereduction stages were smelted in alumina crucibles in a laboratoryscale horizontal tube furnace under argon atmosphere. Smelting experiments were performed at 1500, 1550 and 1600 oC. The amount of excess coal used in prereduction step was another variable. Sivrihisar laterite ore is a limonitic one with low MgO composition. Therefore, MgO was added to the smelting charge as a flux. The effects of experimental variables on metal Ni content and slag composition were investigated.

Jan 1, 2012

By C. J. Beyke

The U.S. Bureau of Mines has developed a process for the selective recovery of Pb metal from a mixed Pb-Zn concentrate. The concentrate was leached in recycled H2SiF6 at atmospheric pressure and 95° C with a redox potential of 570 mV (Eh). Eighty-five pct of the Pb was selectively leached from the concentrate while 87 pct of the Zn remained in the residue. Pressure leaching of the concentrate was slightly less successful, with 78 pct of the Pb leaching from the concentrate and 80 pct of the Zn remaining in the residue. Pure Pb metal was successfully electrowon from a purified PbSiF6-H2SiF6 solution with 96 pct current efficiency and 0.69-kW.h/kg energy consumption.

Jan 1, 1991

By Benoit DeBecker

Laboratory-scale experiments have shown that chromium metal could be recovered from chromate wastes by modifying slightly the chromium electrowinning flow-sheet. After reduction by sulhr dioxide and precipitation of chromic hydroxide, the solid residue is dissolved in the chrome alum solution and the metallic impurities are removed by cementation on manganese. The presence of dissolved manganese in the electrolyte does not affect the cathodic deposition of chromium and it eliminates the anodic production of Cr(V1).

Jan 1, 1994

By N. Menad

The formation of the dioxins can be dependent on the quantities of carbon, hydrogen, chlorine and oxygen present in a given system, as well as on parameters such as temperature and pressure. Inadequate supply of combustion air ( incomplete oxidation ), low combustion temperatures ( incomplete combustion ), and insufficient turbulence in the combustion are factors which can favour their formation. Dioxins were produced also calatytically from chlorinated phenol precursors, non-chlorinated compounds that were chemically, and reaction of phenol with inorganic chloride. In this paper different precursors such as combination of C, H, 0, Cl, rapid formation/combustion intermediates and routes to PCDFs are reviewed, and the influence of PVC amount on the formation of these isomers is discussed.

Jan 1, 2000

By R. W. Adams

A new process has been developed for leaching zinc sulphide concentrates at atmospheric pressure using air or oxygen plus nitrogen dioxide in dissolved or gaseous form as? an oxygen carrier. The process is flexible and can cope with variations in the degrees of retention and regeneration of dissolved nitrogen dioxide in the leaching phase. By controlled addition of concentrate a leach solution with low residual nitrate concentration can be produced. Following separation by filtration of unleached solids and elementa1 sulphur and conventional oxidation/precipitation of dissolved iron, the leach liquor can be treated with metallic zinc to remove the remaining nitrate and other meta111c impurities such as copper, cadmium and cobalt to provide a solution suitable for electrolytic recovery of zinc. Pilot scale testing of the process .has given zinc recoveries in the high nlnet1es, production of a hi.gh grade jarosite-free Pb/Ag residue (50% Pb.) and a saleable high grade of elemental sulphur. .A wide range of concentrates can be treated containing substantial levels of lead and copper as well as zinc. Indicative cost estimates suggest that the new process is competitive with alternative procedures such as pressure leaching.

Jan 1, 1990

By D. M. Hausen

The term "auriferous pyrite" relates to an association of gold with pyrite in a variety of textural forms that affect metallurgical treatment. Extraction of the gold depends not only on the grain size and distribution of the gold in the pyrite, but also on the crystal size and surface area of the pyrite. Occlusions of medium to coarse gold may be liberated by moderately fine grinding. The amenability of finely dispersed (submicroscopic) gold depends in part on the activity of the pyrite surface for oxidation. Two types of auriferous pyrite at Carlin, Nevada, have been examined by optical microscopy and SEM methods before and after aqueous oxidation test work to show how differences in morphological features can affect rates of oxidation and amenability to gold extractions by methods of chlorination and low temperature oxidation.

Jan 1, 1981

By Mark Cross, Andrew P. Campbell, Koulis A. Pericleous

"Computational Fluid Dynamics (CFD) modelling is being used to simulate the freeze layers formed within direct smelting processes. There has been some concern whether water-cooled elements can withstand the p~ocess conditions and in particular abnormal cases where they may be splashed in molten metal.To validate the models being developed, two cases from literature have been modelled for solidification and stress analysis. The solidification case is presented in detail and is for hot molten metal flowing through a cylindrical pipe. The walls are at a temperature below the melting point for the metal. The resulting solid (or freeze) layer is within 3% of the value calculated by Sampson & Gibson9 •Preliminary modelling of the refractory-slag interactions is presented. Although three basic mechanisms: Penetration; Corrosion; and Erosion will eventually be modelled, only the penetration is considered here. The corrosion mechanism is to be modelled by tracking the time that the penetrated refractory is at the required temperature.Future work, after adding all the required physics, will focus on the modelling of a water-cooled element placed lower in the smelter. Process perturbations will be simulated to examine what these elements will withstand."

Jan 1, 2001

By A. J. Paul, K. O. Yu

"Today, foundries are moving towards the use of models and design tools to gain a competitive advantage in producing castings of high desired quality. This leads to a growing alliance between foundries, software developers and researchers seeking to model, visualize and understand the phenomena taking place during the casting process. In addition, there is a need to develop affordable techniques to produce parts in small lot sizes. This leads to the development of a Flexible Manufacturing System consisting of: (1) up-front computer-aided engineering; (2) computer integrated proto typing with solid freeform fabrication; and (3) fabrication of the actual mold and related equipment to cast the part.This paper discusses some of the developments that are taking place today in the areas of modeling the physical phenomena during the casting process as well as towards developing a Flexible Manufacturing System for producing cast parts. Areas that require most work involve prediction of defects and mechanical properties using simplified analyses. In addition, electronic data sharing for collaborative engineering between geographically dispersed team members is also discussed. Case studies are presented showing successes as well as failures.IntroductionCasting, one of the oldest forms of metalworking, has recently seen a flurry of developments in the area of solidification modeling. These developments have come about after the realization that, in order to stay competitive, foundries need to reduce their scrap rate and production costs, and increase casting quality. Even though this is not new knowledge for foundry engineers, the tools to help them achieve this goal are just being developed and put in place for use by foundries. Several state-of-the-art software packages are currently available to analyze the solidification behavior in complex shaped castings. These packages make use of several different approaches for solving the various problems associated with casting processes. The overall architecture of a comprehensive solidification modeling system is shown in Figure 1."

Jan 1, 1994