Search Documents

By J. L. Liow

Studies have been carried out on the causes and effects of slopping in an annular cylindrical geometry such as the top submerged combustion reactor. Properties of standing waves formed such as the wave profile, period, pressure distribution and velocity have been derived analytically. The wear profile due to wave erosion was calculated based on the assumption of linear motion and that the wear is a dissolution process. The use of the j, factor showed that the wear was proportional to the square root of the wave velocity at any point. Using the dimensions of the lsasmelt reactor given by Errington et al. (1987)[11, the wear profile due to wave erosion was calculated using the analytical solution. The wear profile calculated was shown to have a maximum just below the initial bath surface. The wear was found to be concentrated in the region where the first asymmetric standing wave was most active. The results showed that the refractory near the bath surface will be affected by wave erosion, more so than any other parts of the reactor. The contribution of wave erosion on wear must be accounted for in assessing the total refractory wear of a vessel in which slopping exists.

Jan 1, 1991

By F. Chabchoub

A mathematical model has been developed to study the influence of process variables on the horizontal Ohno continuous casting process. The model simulates the heat transfer and fluid flow in a wide plate ingot of pure tin. A two dimensional numerical analysis based on a control-volume finite difference approach, the Semi-Implicit Method for Pressure-Linked Equations algorithm (SIMPLER), and an Enthalpy Transforming Model was used. The shape and position of the solid-liquid interface were calculated at different casting speeds, ingot thicknesses, and cooling device characteristics, as well as various mould temperatures. Results of the mathematical model were compared with

Jan 1, 1992

By Robert H. Hsu

Palladium finely dispersed in a substrate of kieselguhr, Pd/k for short, has been successfully used for hydrogen storage, separation and pumping for a number of years at the Savannah River Site (SRS). Recently SRS has developed a new pd/k flow through bed (FTB) prototype for separating hydrogen from other gases and simultaneously storing the hydrogen on palladium. The FTB uses single-pass liquid nitrogen cooling during hydrogen absorption/separation/storage and electrical heating for desorption/unloading of hydrogen. Fourteen absorption-desorption or loading/unloading cycles using hydrogen have been conducted with the new FTB prototype. Test results show that all design performance objectives have been successfully achieved: recover 295% of hydrogen gas from feed gas, produce 99.9% hydrogen product gas and < 5% hydrogen in discharge gas. This paper will discuss characteristics of the palladium-coated kieselguhr or diatomaceous earth, design and operation of the FTB, and results of performance tests such as separation efficiency, hydrogen storage capacity and system heat transfer characteristics.

Jan 1, 2002

By L. Salinas

Lance injection of gas and particles into a molten bath is currently practised in metallurgical processes (Mitsubishi lances for example). Several experimental and theorical studies have been conducted in the past on this topic. However, neither detailed calculations nor experimental studies of local flow patterns have been published. In the present work, a numerical simulation of the interaction of a gaseous vertical descending jet and a liquid surface was done, using the turbulence k-e model. There is a fair agreement between the calculated and the experimental values. The results of this study demonstrate that it is crucial that the gas jet velocity profile and turbulent characteristic are correctly formulated in order to correctly simulate the system.

Jan 1, 1999

By Levent Özmen

Colemanite is a mineral containing varying amount of boron that is found in abundance in Turkey. It has a good possibility to be used as a flux in iron and steel industry. In this study a review of the use of colemanite, as a flux agent in steel production has been carried out and various related aspects such as its influence in metal-slag reactions, solubility of lime and magnesia in the slag are discussed along its performance in several points of views including its technical and environmental usage characteristics. Positive and negative factors of using this material as a flux are also underlined.

Jan 1, 2006

By M. W. Wadsley

Despite the convenient subdivision of extractive metallurgy into hydro- and pyro- divisions, many flowsheets contain both types of process. When complex materials are used as feed, combinations of hydro- and pyro-metallurgical processes are even more common. Hydrometallurgy is used to treat many by-products and waste-products. (Bio-metallurgical processes may be considered to be a sub-set of hydro-metallurgical processes.) Combinations of the different processes in the Australian metallurgical industry are described. Selected international examples demonstrate that the use of combked processes is not a unique. Antipodean phenomenon. The motives for selection of combined pyre- and hydro-metallurgical processes in a flowsheet are examined.

Jan 1, 1994

By Manuel Zamalloa

The outstanding metallurgical performance of the Noranda continuous converter (NCv) in operation since November 1997 has allowed the company to meet production and environmental targets. This achievement positions this new technology as a strong alternative continuous converting technology for copper production. Knowledge of slag chemistry has been important in this respect. The purpose of this paper is to discuss the effect of key parameters including temperature, oxygen potential, slag composition and levels of copper oxide in slag on the conditions leading to magnetite precipitation, as well as on the conditions affecting the liquidus ranges of NCv slag. The above variables are evaluated using industrial data and thermodynamic predictions. Practical implications of customizing operational fluxing procedures to determine optimum operating windows are also discussed.

Jan 1, 1999

Electrocrystallization studies were conducted in a concentrated acid-copper electrolyte to determine the influence of chloride ions and glue on copper nucleation and on the structure of thin copper layers. Electrochemical experiments allied to SEM and XRD examination were performed to characterize the mechanism of nucleation in the presence of additives at 65°C. Results indicated that most of the copper nucleation from a 83 g dm-3 Cu2+ solution, with 140 g dm-3 of H2SO4 is achieved in a matter of milliseconds, Although the presence of chloride and glue, at the concentration levels tested, does not seem to substantially modify the nucleation mechanism, the morphology, nuclei density and the copper film structure and orientation are changed by the presence of additives and by electrolyte stirring.

Jan 1, 1999

By Stober, Frank Allan

The paper describes the development of components in an lntegrated Furnace Control system for shielded-arc smelting focusing on operation and crucible integrity enhancement. The paper reviews the mechanisms of power, feed and energy input and losses into the shielded-arc smelting process and describes the furnace control system module development and integration to tailor the process. The ultimate success of a furnace control system application is transfer of knowledge, training, and operational support during furnace start-up and ramp-up phases and a model for how this has been achieved is discussed. The control modules of a shielded-arc laterite smelting furnace are described in detail including measured results and screen captures from application in a laterite smelting furnace. This paper focuses on developments in Integrated Furnace Controls tailored to shielded-arc laterite smelting but development of common furnace control modules for improved crucible and tapping operation integrity applied to other furnace processes, including immersed-arc smelting, is also covered. Keywords: IFC, Power, Feed, Supervisory, Control

Jan 1, 2004

By George Grandy

Kvaerner experience is being used to develop software to design or simulate crushing and screening plants. The model techniques discussed are presently being used for open-circuit plants and are being extended to closed circuit plants. The program contains a library of routines, each representing a piece of equipment or unit operation, which are assembled into one of several open-circuit plant configurations. Routines include gyratory primary crushers; standard secondary and shorthead tertiary cone crushers; single, double or triple deck screens; and stockpiles, feed bins and belt conveyors. The program uses steady-state models to simulate the performance of crushers and screens that have small residence times and quickly reach equilibrium when operating conditions and/or parameters are changed. The dynamic aspect of the total circuit model concerns the storage units within the circuit, i.e. stockpiles and bins, and, in the closed circuit configuration, circulating loads and size distributions. In many cases, just vendor&apos;s catalog data are necessary for a pre-feasibility simulation; in other cases, actual plant test data are required to obtain more accurate simulations. The entire plant is shown in a single graphic screen so the user can see all the relevant information he might want, and soft-keys are provided for the user to make on- line parameter changes and observe the effects on storage elements, equipment feed rates and the final product size distributions. The model also reports equipment utilization in percentage, power consumption, and other related operating information, and soon, will be able to report estimated capital and operating costs.

Jan 1, 1999

By Philippe Charlier

Recycling of aluminium contained in used aseptic beverage cartons is a difficult task which has nevertheless to be tackled by our modern societies. Techniques have earlier been developed by the paper and pulp industry for the recycling of the board fibres from collected post-consumer beverage cartons. A joint technical feasibility study by Granges and a leading beverage carton producer has dealt with different techniques for handling residues from repulping facilities. The aluminium obtained can be used as raw material for the production of thin gauge foil, thus closing the recycling loop.

Jan 1, 1995

By R. H. Rubisov

Sulphuric acid pressure leaching of nickeliferous laterites has attracted considerable attention from the nickel industry during the past five years. The process is especially advantageous for limonitic laterites that mostly contain goethite, because iron precipitates releasing acid and thus rendering low acid consumption. It is also applicable to mixtures of limonites and saprolites, although at higher acid consumption due to magnesium. Effective process design requires the solubility of metals that precipitate during the process to be known. In the present work, determination of metal solubilities is based on a simple speciation program that assumes the presence of only one dominant complex for each metal. The thermodynamic data for the precipitation reactions are extracted from high-temperature experiments with monometallic systems published previously. The validity of the approach is then tested against mixed bimetallic systems, and finally applied to calculate the solubility of aluminium, iron and magnesium in laterite leaching effluents "at temperature". In both cases of limonitic feed and limoniticfsaprolitic blends, the prediction closely follows metal solubilities measured experimentally at temperatures from 230 to 270°C and at terminal he acidities ranging from 10 to 75 g/L.

Jan 1, 1999

By Yoshisada Michiura, Junko Umeda, Katsuyoshi Kondoh

Rice husks or straws, one of the main agricultural wastes in South-east Asia, have a large possibility to be employed as usefully renewable resources to produce energy and high-purity silica (SiO2), because they consist of about 70% organics such as cellulose or hemi-cellulose, and 20% amorphous SiO2. The former is utilized as bio-mass energy; for example, thermal or electric energy, and bio-mass ethanol. High-purity silica can be used as raw materials in the industrial uses. It would be possible to extract silica elements from rice husks and straws by burning them in air because their main contents are organics. In the previous studies, a strong acid leaching treatment on rice husks before burning was carried out by using H2SO4, HCl and HNO3 to prepare high-purity silica materials. This was available to accelerate the hydrolysis of celluloses and hemicelluloses contained in rice husks, and remove the above metallic impurities. A strong acid leaching treatment, however, is significantly hazardous to environment and human life, and causes an increase of the process cost. In this study, the environmentally benign, harmless to human and economically effective process to produce high-purity amorphous SiO2 materials from rice husks has been established without using strong acids. From a viewpoint of the harmless influence on human body, the carboxylic acids were used in the leaching treatment on rice husks. TG-DTA measurement and GCMS analysis indicated that the leaching was effective for the hydrolysis of celluloses and hemicelluloses contained in rice husks at 473K~873K, which produced the same results in using the conventional sulfuric acid. The metallic impurities could be also removed from the husks via a chelate reaction between carboxyl groups (-COOH) and the metal elements. In particular, it was clarified that cadmium (Cd) were completely removed from rice straws by this reaction. Concerning the burning conditions of rice husks after the acid leaching, it was necessary to supply a suitable amount of air to completely combust organics; for example it required air supplement of 50 ml/min. or more. The burning temperature should be less than 1273K to obtain amorphous structured silica. High-purity amorphous silica materials with 99% or more were prepared from rich husks by applying the citric acid leaching treatment and burning process at 1073K in air.

Jan 1, 2008

By Sung-Joo Lee, Gi-Chon Han, Nam-Il Um, Hee-Chan Cho

"In Korea, almost all of bottom ash produced by coal power plants is disposed of in ash ponds. Ash storage areas comprise more than 80% of most coal power plant sites. This disposal method is causing environmental problems and a managerial burden for plant operators. In this study, investigations to develop a beneficiation process for separating coal pond ash into various products were undertaken. To improve efficiency of the separation, coal ash was separated by sizes and each size fraction was subject to various beneficiation processes. The separation process used were flotation (-200 mesh size), hindered settling (16x200) and tabling (16x200 and 8x16 mesh). The results showed that various marketable products, such as lightweight aggregate, sand, high-carbon fuel, could be recovered from coal pond ash using simple physical separation techniques.IntroductionDue to the increased use of coals every year, about fifty million ton of coals were used in 2007 alone. As a result, about 6 million tons of coal ash were generated. In Korea, the coal bottom ash is classified as a general industrial waste and is usually disposed of in ash ponds. The costs for this disposal method continue to increase due to rising costs of site management and development and more strict environmental regulation. Therefore, utilities are constantly looking for ways to increase utilization of coal ash. In this study, various beneficiation processes were evaluated to examine the possibility of separating coal pond ash into various products which can be used as aggregates and high-carbon fuel."

Jan 1, 2008

By A. N. Lasseigne

Hydrogenation behavior of the NaAlH4 intermetallics is investigated utilizing thermoelectric power and magnetic analyses. Using both thermoelectric power and magnetic susceptibility measurements on these intermetallics allows for confirmation and further insight into hydrogen&apos;s role in altering the material&apos;s electronic structure. The electronic and magnetic property correlations will indicate the direction for further alloy development to optimize hydrogen storage.

Jan 1, 2006

By L. N. Ertzeva

The process for thermal treatment of current pyrrhotite concentrate in reducing environment with the use of disperse metal iron as an iron-bearing additive (optimal volume 20-30%), with downstream magnetic separation of the calcine, has been studied. The reduction process has been performed in conditions emulating those of both tube and fluidize-bed furnaces.

Jan 1, 2006

By G. J. Shiflet

This paper will review work done in our laboratory on the formation, thermodynamics and crystallization of aluminum based metallic glass with the addition of rare earth elements. The results demonstrate that the metallic glasses are truly amorphous and not microcrystalline and that they are unusual in their formation because the alloys contain 90 at. % aluminum and there is no deep eutectic present in the phase diagram. Tensile strengths that exceed 900 MPa are obtained for several of the compositions and exceed 1000 MPa after partial crystallization.

Jan 1, 1992

By Mikio Kobayashi

Extraction of valuable metals from sulfide ores continues to be a very important, process and so the strict control of discharge of harmful metals in effluents from refineries becomes more important in the future. The recovery methods for heavy metals have been developed. Some metals such as Se and As are still difficult to be removed to very low concentration, although the techniques for recovery and removal for many kinds of heavy metals have already been developed. Especially, in case of Se the recovery system from water with low concentration has not be developed yet, although the WHO decided Se to be harmful for human beings and then the discharge control is under obligation now. In general Se exists as selenite ion and/or selenate ion in aqueous phase and selenite ion is able to be recovered by coprecipitation with ferric hydroxide or by reduction to solid selenium by general reductants. Selenate ion, however, has a strong resistance to conventional treatments. Therefore the new technique for the recovery of Se from water including selenate ion has to be developed. In this presentation the new approach for removal of selenate ion using the reaction in which ferrous ion is oxidized to ferric ion is presented. Selenate ion is reduced to selenite ion during the reaction and then to solid selenium, while ferrous ion is oxidized to ferric ion. The coexistence of activated carbon is very useful to increase the reaction rate. The use of iron powder is also effective and very useful for reducing gel-like precipitates mainly consisted of ferric hydroxide. The concentration of the residual selenate ion is probably under 0.1 ppm after recovering Se by the mentioned-above approach. In addition to the mechanisms of these reactions, the effects of pH, coexistent positive and negative ions, and reaction temperature are also presented. Furthermore the investigation of the behavior of selenosulfate is presented.

Jan 1, 1998

By Vânia L. L. Andrade

Igarapé Bahia Mine is located in Carajás area, northern Brazil. Currently Companhia Vale do Rio Doce operates there a CIP / heap leaching plant treating an oxide gold ore containing about 4 g Au /t and 0,2% Cu, which produces 11 t of gold per year. Recent geological survey has identified a signifcant copper-gold reserve underneath the oxide gold ore. The processing aspects of this copper-gold sulphide ore are described in this paper. It includes ore characterization studies, grinding and flotation tests, orebody variability assessment, flowsheet selection and preliminary economical evaluation Emphasis is given to studies aimed at depressing fluorine bearing minerals to achieve a clean and marketable flotation concentrate.

Jan 1, 1999

By A. G. Raraz

Reactive metal electrorefining presents a number of problems that pose obstacles to commercial operation. Cerium has been chosen as the surrogate for certain reactive metals because of its thermodynamic and electrochemical characteristics. A comparative review of the properties for cerium and plutonium has been presented to justify the choice of cerium as the surrogate metal for studying electrorefining. This review has addressed the electrochemical, thermodynamic, and kinetic parameters of molten salt electrorefining of cerium metal to provide an insight to this extremely important process. The cell components and configuration, current efficiency of the process, purity of the cathodically deposited metal and the power requirement of the system are evaluated for a molten CaCl2-MgCl2 salt electrolyte using a molten, stirred impure anode. Crucible designs, salt electrolyte, cell temperature and electrode materials are also evaluated. Selection of the salt electrolyte and the cell temperature have been suggested from this study.

Jan 1, 1992