Search Documents

By M. K. Mohanty

Over the years, screen bowl centrifuges have been widely used for dewatering fine coal in coal preparation plants in the United States and elsewhere. Its popularity is attributed to its relatively low cost, its high capacity of providing low moisture content product and its relative ease of operation and maintenance. It is generally recognized in the engineering and scientific communities that screen bowl centrifuges provide some degree of particle size separation while dewatering fine coal in a common application. However, the extent of differential partitioning of coarse and fine particles achievable by a screen bowl centrifuge has not been systematically studied in the past. The present investigation was aimed at conducting a parametric study using a statistically designed experimental program to better understand and optimize the size classification performance of a screen bowl centrifuge. A continuously operating screen bowl centrifuge having a bowl diameter of 0.5 m was used for this study at the Illinois Coal Development Park. Three key operating parameters, i.e., feed flow rate, feed solid content and pool depth, were varied to conduct a total of 17 experiments using a three-level factorial test matrix. Some of the best size separation performances achieved in this study may be described as having an imperfection value of 0.13 at an effective separation size (d50c) of 38 µm and an imperfection value of 0.27 at an effective separation size (d50c) of 2.8 µm. Due to an effective separation of ultrafine high ash materials, the ash content of the screen bowl feed was reduced from 22.3% to a minimum of 8.84% with a combustible recovery of 84.1% and an ash rejection of 71.6%. A higher combustible recovery of 92.1% was achieved at a product ash content of 12.5% with a d50c of 2.8 µm and imperfection of 0.27.

Jan 1, 2008

By P. M. Prasad

Off-grade molybdenite concentrates, mainly derived from secondary sources as by-products of the processing of copper, uranium and tungsten ores, do not satisfy the purity requirements (percent MoS2) for the production of molybdenum bearing products. This investigation is a continuation of a successful effort to refine a low-grade molybdenite concentrate to prepare a high-grade MoS2 using a mixed acid (HF + HCl) leach procedure. Specifically, this investigation is concerned with an understanding of the separation chemistry underlying the removal of the oxide/silicate gangue and the base-metal sulfide associations present in the low-grade molybdenite by their selective dissolution in the two acids. Experiments were conducted on an off-grade concentrate containing 42.6% Mo. Results of the controlled dissolution tests indicate that both HCl and HF are suitable for the removal of the associated alumina and both work well for iron, nickel and copper. However, HF was found to be the most effective for dissolving silica/silicate and magnesia. An attempt was made to rank the leaching efficiencies of the acids used singly, sequentially or in a mixed mode. Scale-up (300 to 2,000 g) experiments were conducted to validate this approach. Excellent purification of the concentrate was possible by processing the off-grade concentrate with 10% HCl plus 15% HF at 363 K for 7.2 ks in open polypropylene reactors with internal stirring. These conditions leached practically all of the oxide and silicate gangue and 96% of the metallic impurities. Starting from the low-grade molybdenite concentrate (42.6% Mo; 71.1% MoS2) it was found feasible to obtain a refined product containing 97.8% MoS2, which is suitable for industrial use.

Jan 1, 2007

By Cary Hirner

The Metropolitan Water Reclamation District of Greater Chicago (District) is in the final phase of completing the Calumet System component of the Tunnel and Reservoir Plan (TARP) by bringing the Thornton Composite Reservoir online by 2014. The Thornton Composite Reservoir will provide nearly 30 billion liters (7.9 billion gallons) of additional storage for minimization of combined sewer overflows(CSO) and flooding in the Chicago metropolitan area. The project requires that the existing 6.7 m (22 ft) diameter Thorn Creek tunnel conveying overbank flood flows is re-routed and connected to the Thornton Composite Reservoir. This paper presents the components of the Thornton Composite Reservoir and specifically the detailed evaluation of a drill-blast tunnel. Other project features include an access shaft, control gate, energy dissipating structure, bulkheads, and live tunnel connection. The construction contract will be procured in late 2009.

By S. C. Chelgani

The Thor lake deposit is a world class resource of rare earth (REE) metals and minerals in Canada. Development work to optimize a REE mineral recovery process flow sheet is underway, however, given the ore mineralogy; the developed reagent scheme is relatively complex. As part of a research project, micro flotation tests were conducted on a feed sample in order to examine factors affecting stream partitioning. SEM-EDX was performed to evaluate variability in grain composition between streams (concentrate and tails) and TOF-SIMS surface analysis was used to determine statistically significant differences in surface species particularly related to potential activation (or depression) of the examined mineral phases. SEM-EDX analysis reveal that the concentrate has a significantly higher proportion of REE bearing grains (carbonates and phosphates) relative to the tail (almost none were identified). Spectral fingerprinting by TOF-SIMS has allowed for the identification of all reagent species investigated. Reagent signal intensity discrimination on test stream mineral surfaces was observed by the TOF-SIMS analysis using reagents at plant concentration levels. TOF-SIMS analysis confirmed that REE bearing grains reporting to the concentrate are doing so in response to collector attachment whereas grains reporting to the tail are doing so in response to a lack of collector and/or in combination with the presence of the depressant. The surface analysis of gangue phases reveal a similar reagent discrimination; the signal intensity of collector species was significantly higher on the concentrate samples relative to the tails while depressant species were significantly enriched on the surface of the gangue phases in the tail samples. A detailed evaluation of the surface species representing the various reagents used in flotation scheme revealed a distinct competitive relationship between two of the reagents. The surface analysis identified that when used in concurrently, there appears to be a negative feedback resulting in a significant reduction in loading for several of the collectors on grains reporting to the concentrate. An evaluation of the effect of reagents on REE mineral in pilot plant is currently under way. Key words: Rare earth minerals, Flotation, Surface chemistry, TOF-SIMS, SEM-EDX

Feb 27, 2013

By Clay Haynes

In 2005, Black & Veatch Corporation began designing a raw water conveyance system for San Luis Obispo County from Lake Nacimiento to the city of San Luis Obispo. The first element of the water transfer system will be a raw water pump station and lake tap. The wet well of the pump station will consist of a concrete lined shaft approximately 180 feet deep constructed in the very incompetent sandstone of the Vacqueros Formation. The lake will be wet tapped at approximately 172 feet below grade using a slurry earth pressure balance tunnel boring machine. The 48 to 72-inch finished diameter microtunnel will be approximately 500 feet in length. Construction is scheduled to begin in the winter of 2007.

Jan 1, 2008

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Antonio De Biase

In October 2006, a 7m Double Shield TBM, boring through very poor volcanic formations, was pushed back by fluid mud, which presence had not been detected during previous field investigations, due to the high covers characterizing the majority of the tunnel axis. The present work describes the investigations made to gain better knowledge of the conditions in front and all around the TBM, the special measures implemented, the exploratory and bypass tunnels excavated, the extraordinary occurrences came true during the execution of these tunnels, the drainage campaigns, the design of the chamber excavated to free the TBM, the dismounting and restarting of the TBM.

By G. F. Jenkins, P. S. Hobden

Toronto as a geographical area provides an exceptionally wide variety of subsoil stratiphication. Tunneling consequently required a very wide range of adaptabilities to meet its changing conditions. This discussion will provide a summary of work performed in both earth and rock formation using three of our recent works to describe a Contractor's experience. The general subsoil stratigraphy is known to consist of deposits laid down during the Illionian Glaciation followed by the Samgamon Interglacial Stage and finally the Wisconsin Glaciation. All these deposits are underlain by shale bedrock of the Dundas formation. As a whole the Dundas formation is predominantly a greyish blue, thinly bedded shale. The engineering characteristics of the shale vary considerably, however, between a blue clay (argillaceous) shale and a much lighter (in colour) silty and sometimes sandy (arenaceous) shale, and occasional limestone layers. The Illionian deposits are usually found to be layers of pebbly clay till and an overlaying layer of contorted varved-clay. These glacial deposits can be overlain by a thick layer of sandy silt to silty sand which is identified as the Samgamon Interglacial sediments. Because of the action of erosion the Wisconsin till sheets, many times separated by interstadial sands, can vary greatly in their number of layers from zero to three or more.

Jan 1, 1997

By K. A. Grace

K.A. Grace's article advocates usage of the terms describing resources as defined by the US Bureau of Mines (USBM) and the US Geological Survey (USGS). Originally recommended in 1943, the terms were revised in 1976 and again in 1980. Mr. Grace further recommends that the term reserves should be severely restricted and that it should encompass mining and processing factors. The list of references quoted in the article does not, however, mention the study concerning reserves that was made over a period of almost four years by a joint Committee on Definitions. This committee was sponsored by three societies - the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the Society of Economic Geologists (SEG), and the American Institute of Professional Geologists (AIPG). Most of the detailed work was done by a working party appointed by the Society of Mining Engineers (SME) of AIME. After studying previous definitions in the US as well as in the United Kingdom, Canada, Australia, France, and other European countries, the following definitions were proposed and accepted in 1974 by the SME board of directors. (Ore reserve definitions in Rhodesia, South Africa, or New Zealand were not mentioned as having been reviewed.) Table 1 lists definitions from MINING ENGINEERING, July 1975. Notice in Table 1 it was mentioned, under Resources, that the definitions of reserves were recommended for the purposes of commercial evaluation. It was further stated that the terminology adopted by the USBM and the USGS, as released to the public, covering resources, was recognized as such. Mr. Grace also recommends that reserve calculations should allow for future losses in ore tonnage, ore grade, milling, and smelting. Unfortunately, it might take years to develop a prospect after it has been discovered. Mining methods have to be tested before being finalized in order to know what tonnage of ore is going to be lost, or how much dilution is likely to occur. The same problems are present in concentrating or in smelting. Operating mines usually know how mined grade compares with ore reserve grade. They can usually predict fairly closely what their final metal recoveries are probably going to be. It is, however, expecting too much to have to delay quoting reserves from say a recently drilled prospect. Any responsible mining geologist or mining engineer (or company for that matter) should state several things about an ore reserve calculation: that it is or is not a preliminary estimate only; that estimated grades have not been diluted to allow for a future, as yet unknown, mining method; that metal recoveries are or are not only tentative, based perhaps on drill hole samples only or on no metallurgical testing at all. Reserves of a partially explored prospect are always quoted when it becomes necessary to raise capital. If they are described as preliminary only (really just tonnage and grade estimates and not true "reserves") in addition to being accompanied by some of the items just mentioned, nobody is going to be misled. If, on the other hand, a report by a member of the SME or SEG is intentionally misleading, the individual must be reported and eventually disbarred from his or her society. To summarize, let us stay with the definitions of ore, ore reserves, and related terms as recommended and accepted by SME. I might add that on occasion I have used a fourth category in my ore reserve calculations, namely Geologically Possible Ore. This category is more or less the same as Inferred ore defined by the USBM and USGS. I have never given a grade to this category, which may be based only on geological mapping, geochemical sampling, or geophysical traversing.

Jan 8, 1985

By R. D. Begley

This paper will present detailed design drawings of a flexible single floor residential superstructure proposed for both longwall and room and pillar mining conditions. All efforts were made to provide an immediately available economical alter- native for future home builders on subsidence prone land. Based on this fact, a basement was not included in the design because additional costs and measures would be required to minimize cracking and leakage. A cost comparison with a traditional superstructure demonstrated that this would be a cost effective alternative. The criteria used to determine the design of the residential structure was as follows: 1. The appearance should not be different then a typical three bedroom residence; 2. Only commercially available devices and present architectural and engineering technology should be used to achieve the required "flexibility" of the super- structure; 3. The structure as completed would be capable of resisting a predetermined amount of vertical and horizontal movement; and 4. If the structure was to experience stresses beyond its capabilities, it could be easily removed from the foundation and releveled.

Jan 1, 1986

By C. Bazin

The separation of rare earth elements is a complex process that is industrially carried out using liquid/liquid extraction. Detailed flow sheets of solvent extraction plants for the separation of rare earth elements are rarely available in the literature which limits the opportunity to teach and test the application of data reconciliation, process optimization and control to these types of plants. The basis of a simulator for a rare earth elements separation plant is described in this paper. The simulator is used to adjust the organic phase and stripping acid flow rate in a separation circuit of heavy rare earth elements from light one?s.

Feb 27, 2013

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Thornton L. Neathery

Vertical magnetic surveys have been made over about 3, 150 miles of the crystalline area of east-central Alabama. A contour map (100-gamma interval) showing regional magnetic anomalies has been prepared (scale 1:250,000) from data points located at quarter-mile intervals on all public roads. Small one- and two-station anomalies were eliminated, leaving only areally extensive anomaly features associated with regional geology. The regional gradient was "filtered" from the basic data and the resulting magnetic configuration compared to the regional geology. Regional lines of vertical magnetic intensity trend northeast and follow the structural framework of the area. Correlations can be made between a large number of geologic and magnetic features. The strongest regional anomalies are associated with the Goat Rock, Bartletts Ferry, Towaliga, and Brevard fault structures. The Inner Piedmont area is characterized by a broad regional high. The magnetic values of the northern Alabama Piedmont grades gently northwestward, disrupted occasionally by elongate highs and lows associated with amphibolites or granites. Scattered throughout the Piedmont are anomalous areas of high magnetic intensity; some are related to magnetic-bearing rocks, and some Indicate possible mineralization. Most of the anomalies have not been evaluated,

Jan 1, 1972

By Hassell E. Hunter

The Wyoming Mineral-Conoco Crownpoint Project represents the first time that big hole drilling has been exclusively used to develop totally a privately financed mine below a depth of 1000 feet. Three shafts, one ten feet in diameter and two six feet in diameter, were successfully drilled to depths of 2243', 2188' and 2188' respectively and cased with hydrostatic designed steel casing. The largest shaft is to be used to handle muck and water from station excavation and enlargement of the other two shafts. A reverse circulation system with potassium chloride base mud was used for drilling. The mud was cleaned by settling in steel lined tanks with assistance by cyclone type separators. Deviation was monitored by gyroscopic surveying at 30 foot intervals and did not exceed 16 inches off plumb. Casing was designed to withstand hydrostatic pressures with a 1.5 safety factor to the large shaft and 1.25 safety factor for the smaller shafts. All casing welds were x-ray tested prior to lowering the casing in the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1983

By G. Tiravanti

A recurrent concern in mining operations is how to deal with the large volumes of fresh water used which in turn generates large volumes of effluents that have to be treated. Water treatment can focus in one of two main strategies: treat the effluent as it is produced, or use a simulation tool to optimize water use in the process and reduce volume of effluents, contaminants concentrations, operational costs, and so on. This article shows a successful tool developed in Matlab-Simulink® that allows modelling a mining process and simulating potential improvements to evaluate the results. This tool has been proven in Cu-Mo operations and recently it has been used in poly-metallic operations. This article reviews the 4 Key Steps required to achieve our goals: a) Elaboration and verification of the mining Operation?s Block Diagram, based on a field survey; b)Model construction and input flows and qualities in selected streams; c)Model Validation and Simulation of new alternatives like recirculation, changes in reagents and dosage, partial treatment, flows merges/separation, and others; d)Development of the Optimal Solution which consists on determining the CAPEX and OPEX.

Feb 27, 2013

By G. Bulut

The recovery of copper and cobalt from ancient copper slags from the Küre region of Turkey was investigated. A fayalitic-type of ancient copper slag containing 1.24% Cu, 0.53% Co and 53.16% Fe were subjected to an experimental study. Two different routes were followed to recover the metal values. The first route was roasting the slag with pyrite followed by leaching. The second route was flotation of the slags, roasting of the flotation tailings with pyrite and leaching. The second route was found to be suitable for the treatment of the copper slag studied. In the flotation step, a copper concentrate containing approximately 11% Cu was produced with a 77% recovery while 93% of the cobalt stayed in the tailings. In the roasting experiments, the effects of roasting time, pyrite: slag ratio and roasting temperature on the dissolution efficiencies of Cu and Co were investigated, and the optimum conditions were determined. In the tests, 87% of the cobalt dissolution was observed after one hour of roasting at 500°C with a pyrite: slag ratio of 3:1. The copper dissolution in the tests was 31%. Based on the results of this study, a process flowsheet is proposed for the evaluation of these slags.

Jan 1, 2007

By Bhaskar B. Thapa

The design of the Caldecott 4th Bore, located along State Route 24 in Oakland, California, is based on the principles of the New Austrian Tunneling Method (NATM). Typical NATM initial support design practices used in Europe were adapted for this project to account for U.S. conditions and requirements, such as degree of experience with NATM construction, the prevailing contractual environment, and preferences for contractual simplicity. Key design features are: (1) support selection criteria based on ground behaviors and ground conditions; (2) a prescriptive design with allowance for support adjustments based on observations during construction; and (3) organization of support requirements into only four major support categories, while permitting some adjustment for variations in ground behaviors and conditions using a few subtypes and additional support measures.

By J. P. Brady

A major spontaneous combustion incident occurred in the sealed goaf of the SL3 Panel; Southland Colliery in 2003 resulting in the loss of a longwall and sealing of the mine. The most important issue for the new owners, Yancoal Australia Pty. Ltd, was to effectively manage the atmosphere in the fire affected sealed area. This atmosphere comprised of flammable gases, the products of combustion and excessive levels of oxygen due to pressure differentials across the panel isolation seals with a potential ignition source associated with the residual spontaneous combustion event. The challenges were met in the first instance by the erection of pressure balance chambers with limited success. The problem was not solved until the pressure chambers were pressurized using a Floxal Nitrogen Plant supplied by Air Liquide Australia. Given the success of this approach on a small scale, a higher capacity Air Liquide Floxal Unit was acquired to manage spontaneous combustion at the recommencement of longwall mining operations. This provided the ability to pressurize pressure chambers that were installed in the Maingate Seals behind the face of the adjacent Longwall Block effectively preventing the ingress of oxygen and permitting the goaf to self inert in a reasonable time period. This paper summarizes a new proactive method of mitigating the risks associated with active and sealed goaves. Proactive management of these areas using low flow nitrogen into pressure chambers to maintain a positive pressure has eliminated typical reliance in explosion proof or explosion resistance seals as the primary control.

Jan 1, 2009

By A. Moergeli

The Swiss are building the world’s longest tunnel, the 57-Kilometer (35-mile) long Gotthard Base Tunnel. Lot 252, Tunnel Amsteg: Two Hard Rock Tunnel Boring Machines (TBM) crossed hydro-thermally decomposed granite. While the East TBM advanced slowly but steadily, the West one got stuck for five months and had to be recovered by special means and methods. Both TBMs have finished their more than 11-Kilometer (7 miles) long drives successfully. Lot 360, Tunnel Sedrun: For the first time in tunneling, roadway support machines are used through most challenging, squeezing geology. They constantly advance in full face mode for about one Tunnelmeter/24 hours.

Jan 1, 2007