Search Documents

By R. Robertson

Dense medium cyclones are the preferred means for cleaning 112 in. x 14 Mesh to 28 Mesh (12.7 mm x 1.0 mm to 0.6 mm) raw coal and are becoming a common choice for cleaning raw coal from a nominal top size of 2-1/2 in. to 3 in. (63.5 mm to 76.2 mm) down to 14 Mesh to 28 Mesh (1.0 mm to 0.6 mm). During the last ten years, dense medium cyclone circuitry design has undergone changes which have combined to improve process efficiency. This paper describes these improvements and compares present day design with the design used prior to the mid 1980's. Improvements in the following areas are described: Raw coal desliming, cyclone configuration, drain and rinse applications, dilute medium circuitry, and instrumentation and control.

Jan 1, 1997

By M. Shriwas, F. Calizaya

"Recirculation is prohibited in many coal mining countries because of the fear that the re-use of return air would allow the build-up of air contaminants at the workings. The incorrect design and location of a booster fan in any ventilation network can create unsafe condition due to recirculation. The current approach to investigating recirculation using simulation software requires manual effort which becomes tedious in a complex and a large network. An algorithm-based C++ program was designed to detect the recirculation in a booster fan ventilation networks. This program needed an input file prepared from output file generated by any ventilation simulator. This program created an output file for recirculation. This program demonstrated the strong capability to detect the recirculation in a sample network and a coal mine ventilation network. The outcomes of this program were documented in this paper. INTRODUCTION The proper design and location of booster fans eliminate the safety hazards associated with high main fan pressure. Conversely, the incorrect design of booster fans in any ventilation network can create unsafe conditions due to uncontrolled recirculation. The proper utilization of a booster fan derives benefits to reduce the main fan pressure, leakage, and consequently ventilation cost especially with high resistance network due to deep and extensive working area in a mine. However installation of booster fan may create uncontrolled recirculation, if it is not sized and located properly with respect to main fan. Recirculation is prohibited in many coal mining countries because of the fear that the reuse of return air would allow the build-up of air contaminants at the workings. Therefore, it is imperative to check the recirculation while designing and operating booster fan for a ventilation network. This paper deals with an algorithm based C++ program to detect the recirculation in a booster fan ventilation networks. This program was implemented to detect the recirculation in a sample network and a coal mine network. STATEMENT OF PROBLEM The currently available ventilation simulation programs do not give much information about recirculation for the generated solution (fan pressures). The current approach to investigating recirculation using simulation software requires manual effort, i.e., traversing from node to node in the output network by the simulator while keeping tracks of all the nodes that form recirculation paths. This is an easy task in a simple ventilation network, but it becomes tedious and sometimes very confusing in a complex and large network. Moreover, the presence of multiple recirculation paths makes the manual effort more complex and difficult, especially in separating multiple loops that are connected together. Thus, there is a need for a more efficient program that will detect and quantify the recirculation efficiently, for the generated fan pressures. A program is developed to detect the recirculation(s) in a network."

Jan 1, 2015

By C. D. Harrison

This paper presents the results of 18 high-G centrifuge tests performed at the Electric Power Research Institute's Coal Cleaning Test Facility in January 1985. These tests, using -28 mesh (0.6mm) froth flotation product, show that the high-G, solid-bowl centrifuge can produce clean-coal moistures of less than 12 percent at solids recovery rates exceeding 98 percent. The high-G centrifuge achieved these low moistures by applying centrifugal forces up to 2,000 times gravity. Because these forces are two to three times the forces used in a screen-bowl centrifuge, the high-G centrifuge can use a solid bowl and still produce a low-moisture product. The solid bowl captures ultrafines that would pass through a screen bowl, and thus obtains higher recovery rates than a screen-bowl centrifuge.

Jan 1, 1985

By F. Duan, W. G. Pariseau, C. S. Schmuck

Three dimensional comparisons between calculated and measured displacements in the hanging wall of a rock mechanics study region at the Homestake Mine show correlation coefficients of 0.7 or higher. Two and three dimensional back analysis of the data lead to different scale factors for determining rock mass strengths and moduli from laboratory values and seemingly to different rock mass properties. A simple analytic model suggests that indeed not only are there two independent scale factors, one for strength and one for moduli, but that there is a logical relationship between the scale factors obtained from two and three dimensional back analyses of the same mine measurements. The three dimensional modeling procedure implemented in the finite element code UTAH3 thus seems to have a realistic potential for investigating underground hardrock mine questions not amenable to two dimensional analysis.

Jan 1, 1987

By A. Gene Collins

The demand for lithium may increase because of its potential use id lithium batteries and in the generation of electrical power by fusion. Therefore, lithium abundance in some United States oil-field brines was surveyed. Oil-field brines from numerous locations were found to contain more than 100 mg/l lithium and several exceeded 500 mg/l. An area of 25,000 km2, with a reservoir thickness of 60 m, an effective porosity of 5 percent, and a brine with a specific gravity of 1.2 containing 100 mg/l of lithium, contains about 0.75 x 106 tonnes (1 tonne = 1 metric ton = 1,000 kg) of lithium in 7.5 km3 of brine. It is postulated that the brines were enriched in lithium by lithium-rich spring water or lithium leached from volcanic rocks followed by evaporation sequences.

Jan 1, 1978

By K. C. Nathsarma

An attempt was made to extract niobium oxide from ~98.5% Nb2O5 using solvent extraction processes. Nb2O5 is used as the feed material in carbothermic reduction processes aimed at producing high-homogeneity, super-conductor-grade niobium on a laboratory scale. The Nb metal used for superconductor applications requires a residual resistivity ratio (RRR) > 300, which in turn needs a stringent purity of Nb and allows impurities (substitutional and interstitial) in ppm levels only. In this paper, solvent extraction of niobium was studied under various experimental conditions, such as effect of different extractants, concentration of methyl isobutyl ketone (MIBK) in the organic phase and concentration of various acids. The concentrate was digested with hydrofluoric acid, with ammonium fluoride (NH4F) as a stripping agent. The extraction of niobium from low hydrofluoric- (HF-) bearing solution was found to be low. Thus, various concentrations of hydrofluoric acid and sulfuric acid, as well as hydrofluoric acid and hydrochloric acid, were investigated towards obtaining a maximum amount of niobium in the filtrate and a minimum amount of niobium in the residue. A McCabe - Thiele plot for extraction of niobium from the aqueous phase, HF-bearing solution using HCl with 85% MIBK in kerosene has been constructed to determine the O:A ratio and the number of stages of the process.

Jan 1, 2011

By K. C. Nathsarma

An attempt was made to extract niobium oxide from ~98.5% Nb2O5 using solvent extraction processes. Nb2O5 is used as the feed material in carbothermic reduction processes aimed at producing high-homogeneity, superconductor-grade niobium on a laboratory scale. The Nb metal used for superconductor applications requires a residual resistivity ratio (RRR) > 300, which in turn needs a stringent purity of Nb and allows impurities (substitutional and interstitial) in ppm levels only. In this paper, solvent extraction of niobium was studied under various experimental conditions, such as effect of different extractants, concentration of methyl isobutyl ketone (MIBK) in the organic phase and concentration of various acids. The concentrate was digested with hydrofluoric acid, with ammonium fluoride (NH4F) as a stripping agent. The extraction of niobium from low hydrofluoric- (HF-) bearing solution was found to be low. Thus, various concentrations of hydrofluoric acid and sulfuric acid, as well as hydrofluoric acid and hydrochloric acid, were investigated towards obtaining a maximum amount of niobium in the filtrate and a minimum amount of niobium in the residue. A McCabe - Thiele plot for extraction of niobium from the aqueous phase, HF-bearing solution using HCl with 85% MIBK in kerosene has been constructed to determine the O:A ratio and the number of stages of the process.

Nov 1, 2011

By Gabriel Böde Jimenez Leon, Michael Karmis, Christopher Newman, Zach Agioutantis

"When utilizing high recovery underground mining methods, such as longwall or high-extraction room-and-pillar mining, the movement and deformation of the overburden propagate toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidenceinduced changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, the resulting strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed ruptures, upward, blocking stream flow or having the stream diverted into the fracture zone at the base (Iannacchione, et. al., 2010).Recent investigations on the effects of underground mining on surface bodies of water suggest that to determine the degree of stream impact one must also consider the geologic structure and thicknesses, surface topography, watershed drainage areas, width of river bed and rate of mining. Due to the complex nature and number of parameters affecting surface streams, subsidence modeling tools and software packages should be implemented throughout all stages of subsidence planning, prediction and control. The Surface Deformation Prediction System (SDPS) utilizes the influence function for the calculation of final subsidence deformations with respect to the angle of influence, supercritical subsidence factor as a function of the percent hard rock, edge effect offset distance, and surface topography. Developed more than 25 years ago, SDPS has been continually updated with new analysis and prediction features, providing a reliable and versatile program for subsidence management methodologies. Most recently, the program has been updated to evaluate the effect of varying surface topography in the prediction of horizontal displacements, referred to as ground strain, allowing for the accurate three-dimensional representation of surface deformations in mountainous terrain (Agioutantis and Karmis, 2014). Ground strain has become one of the predominant deformation indices used in the evaluation of potential damage to surface structures (Karmis et al., 1995). Ongoing work with SDPS software seeks to investigate the calculation of ground strain in SDPS and its ability to accurately and realistically predict damage to surface streams due to underground mining operations."

Jan 1, 2015

By Henry E. Swanson

In the early 1960's the Company, then named the United States Smelting Refining and Mining Company, was drilling the Continental ore body located near Fierro, New Mexico. Reserves of underground ore of sufficient quantity were indicated to build a mill. At the same time some ore from the Continental No. 1 mine was being milled at the Company's Bullfrog Mill, formerly a lead-zinc mill. The copper ore in comparison to the lead-zinc ores was very hard, abrasive, and heavy. These factors pointed out the possibility and attractiveness of autogenous grinding. While prior to this some study had been given to autogenous grinding, no large scale tests had been made. Such a program was carried out and from the pilot plant data the following was established: 1. Grinding of the ore by autogenous means could be accomplished. 2. This could be done in one stage; however, not at a satisfactory tonnage throughput rate. Thus, the use of a secondary unit has been employed. 3. Grinding in the secondary unit could be done by pebbles generated in the primary unit. This resulted in the scheme whereby the ore would be ground 100% autogenously. 4. Liberation of the copper minerals was excellent so that good recovery at a satisfactory concentrate grade would be obtainable.

Jan 1, 1976

By James W. Bass

Atmospheric fluidized bed combustion (AFBC) is an improvement in coal-fired boiler design that offers several advantages over conventional boilers. AFC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling which can, in turn, increase a boiler's fuel flexibility. This report discusses, in general, AFBC technology and, in particular, progress at the 20-MW Pilot Plant built by the Tennessee Valley Authority (TVA) at its Shawnee Power Station near Paducah, Kentucky.

Jan 1, 1985

By S. J. Zagula

Improved desulfurization of Illinois coals is a widely Shared research goal. The development of a physical cleaning strategy and the results of a project to demonstrate technical and economic feasibility of producing a low sulfur compliance coal from the Illinois Basin are reported. Processing flowsheets to extend or retrofit existing preparation plants are considered. Comminution, conventional and micro-bubble flotation, and selective agglomeration technologies were investigated to maximize pyrite rejection while maintaining high product yield. Batch bench scale testing was followed by continuous pilot plant studies. Parameters included grind size, flow rates, pulp density, aeration, agitation, and reagent dose. An economic evaluation of targeted processes is included.

Jan 1, 1987

By D. Robert Weir, Roman M. G. S. Berezowsky

Pressure oxidation can virtually always render refractory auriferous sulphidic ores and concentrates amenable to cyanidation. Its effectiveness as a pretreatment of refractory gold feedstocks is reflected by the successful startup and operation, over the past four years, of four commercial plants. At least three more are scheduled to come on stream during the next three years. Over the past eight years, a variety of ores and concentrates have been subjected to integrated miniplant testing and process demonstration by Sherritt, and data derived from these studies have been used in the design and construction of several of the commercial facilities. Some factors affecting the selection of pressure oxidation in gold recovery processing are discussed.

Jan 1, 1989

By John B. Mitchell

Approximately 90% of all potash produced is employed as a fertilizer, either directly or with nitrogen and phosphorus. The remaining 10% is utilized in the manufacture of other chemical products, The original source of potassium was wood ash (hence the name potash), However, today the term potash refers to all commercially important salts of potassium. Sylvite, usually found associated with halite, is the predominant economic potash mineral; carnallite a lesser important source of potassium chloride, while langbeinite is important as a source of potassium sulphate. The world's first potash mining operation commenced in Strassfurt, Germany about 1860, Since that time the industry has grown steadily to its present annual volume of about 30, 000, 000 tons of potassium chloride products or 18, 000, 000 tons of K2O equivalent, potassium chloride or "muriate of potash" being equivalent to 63. 1% pure K2O, WORLD POTASH RESERVES ARE NOT EVENLY DISTRIBUTED The earth's crust contains 2 to 3 per cent potassium, mostly in the form of insoluble silicate minerals. The economically important deposits, however, are formed from brines concentrated by evaporation. The world's most important commercial deposits are of Devonian and Permian age, however soluble potassium bearing salts are presently being concentrated by evaporation in several drainage basins, notably Searles Lake, California, Great Salt Lake, Utah' and in the Dead Sea. At least twenty-four countries are known to have reserves of potash: Canada and the USSR have over 80% of the presently known world reserves, (Figure 1)

Jan 1, 1972

By H. A. von Schonfeldt, H. Douglas Dahl

INTRODUCTION During the past decade, significant pro¬gress has been made in applying rock mechanics principles to mine design problems by a great number of researchers. Some of these new techniques have found their way into the engineering and planning offices of the operating mine. In spite of these advances, however, the application of rock mechanics in the day-to-day mine planning and design of our domestic coal mines is rela¬tively rare. There are a number of reasons responsi¬ble for this relatively slow progress, not the least of which is the question of how to measure the success or cost effectiveness of a sizable rock mechanics effort in an opera¬ting mine. Firstly, the properties of geologic materials generally vary over a wide range and it is, therefore, difficult to assess whether an improvement in the mining conditions is due to a design change or due to a change in the geologic conditions. A second reason for the slow acceptance of rock mechanics in engineering thinking is the fact that some of the concepts are quite difficult and that physical evidence of their validity to mine design is still rare. Thirdly, com¬munication between research, engineering and applications oriented people appears to function only intermittently. In our view, however, the most important impediment lies in the "state-of-the-art." Exactly how much can rock mechanics help the mine operator? The best that rock mechanics can do at present is determine whether one approach is better than another when weighed against some design objective (stress, strain, deformation). We cannot determine the abso¬lute best ground control design -- only what is better. If ground control is lost, the statement that "it's the best one we looked at" means very little to the harried operator. While the "state-of-the art" has advanced a great deal, it has certainly not been reduced to an engineering matter in that design hand¬books are available -- they are not. The success of a rock mechanics program, there¬fore, can be determined only over a long period of time of continuous effort.

Jan 1, 1977

By L. W. Pommier

In the field of minerals processing the concentration of valuable minerals normally takes place in suspensions of ore particles in liquids. The fluid resistance offered by Newtonian liquids to the movement of free settling spheres for the limiting cases of creep flow and turbulent flow is well described by Stokes' and Newton's Laws. However, these equations are not applicable to non-Newtonian fluids, since the relationship between applied shearing stress and resulting rate of shear is a non-linear function, and more than one viscosity parameter is necessary to describe their rheological properties. For this reason, the term "apparent viscosity," which has been commonly used to explain the flow resistance of the non-Newtonian systems including suspensions, may be misleading. A rigorous analysis of the mechanisms of momentum transport of solid-liquid systems is complex indeed. There are many variables that affect the properties of such systems, and precise limitations and assumptions are necessary in order to produce quantitative relationships for predicting their behavior. Very dilute suspensions of spherical particles in Newtonian liquids of identical density as the solids have been examined in the past (12); however, the study of suspensions in which there is a considerable difference in density, between the liquid and the suspended solids has been neglected.

Jan 1, 1968

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

By V. T. McLemore

The Steeple Rock district is a major epithermal .gold-silver district in New Mexico that exhibits district zoning. Five types of ore deposits occur in the district. The base-metal veins (with Au and Ag) form the center of the district and occur along the Carlisle fault. The gold-silver veins occur along northwest-trending faults outward from the base-metal veins. The margins of the district are formed by copper-silver, fluorite, and manganese veins. In addition, areas of older acid-sulfate alteration occur throughout the district and also exhibit zoning: massive silica/chert zone (inner), silicified zone, and clay zone (outer). This alteration overlies regional; alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow but older epithermal hot springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1994

By Thomas F. Joyce

N L Industries, Inc., MacIntyre Development produces ilmenite and magnetite concentrates from its own open pit operation at Tahawus in New York's Adirondack Mountain region. The ilmenite concentrate is used within the company for the production of titanium dioxide pigments and the magnetite concentrate is sold to heavy media processors. Current production is from South Extension mine, loading by by six-yard Marion electric shovels into 85 ton Lectra Haul trucks. Bench heights are 44' and are drilled with a Robbins Rotary 9 7/8" diameter hole on 25' spacing for a yearly production of 3.4 million total tons of rock. The ore deposit occurs in veins dipping on the average at 40 degrees to the west. The ore body, which is divided into three zones, outcrops at surface and continues to depths of 800'. Zone 1 is a high grade band of thickness 150-200' with an Fe/Tio2 ratio of 2. Below this band is Zone 2, a low grade band of thickness 50-100' with an Fe/Tio2 ratio of 2 and beneath that seperated by a band of anorthosite is Zone 3, a high grade band of irregular thickness 50-450' with an Fe/Tio2 ratio of 1.6.

Jan 1, 1973

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965

By G. Jalkanen

Parameter estimation of the inverse distance estimation algorithm is presented. The objective function to be minimized is a sum of squared cross validation errors. The unknowns to be estimated are the exponent of the inverse distance estimator and anisotropic angles and ratios that are used in determining the distances in the algorithm. Examples are presented for both two and three dimensions data sets.

Jan 1, 2009