Search Documents

By G. Zhu

Bulk and differential laboratory flotation tests have been carried out using a synthetic mixture of chalcopyrite and molybdenum ore. In addition to boiling and roasting, six different depressants are tested so that the best conditions of separation can be identified. These reagents include sodium cyanide with and without zinc sulfate, potassium ferrocyanide, sodium hydrosulfide, arsenic Noke's reagent, and sodium sulfide. The data indicate that most of these reagents are effective chalcopyrite depressants. However, sodium hydrosul fide can be used preferably if economic, operational, and environmental factors are taken into consideration.

Jan 1, 1983

By Delon Hampton, Francis K. Mensah-Dwumah

INTRODUCTION The state-of-the art in the area of soil-structure interaction is not sufficiently developed that one can accurately predict the earth load distribution on buried structures. This lack of knowledge has led to the use of high factors of safety in their design and conservative assumptions for the loading diagrams. As a step towards the improvement of the design methodology for buried structures, it is important to be able to apply new analytical techniques and monitor the performance data obtained on full-size buried structures. The performance data should preferably include: 1) the actual stress distribution on the buried structure, 2) stress distribution in the buried structure and surrounding soil media, 3) vertical and lateral movements in the soil adjacent to the buried structure, and 4) deflection of the buried structure. Brown (1967), Davis (1972), Krizek, et al (1974), Krizek and MacQuade (1978), and some few others have compared the performance of full-size culverts with finite element results. Despite all these efforts, a complete understanding of the soil-structure interaction problem has not yet been fully achieved. In an effort to make improvements in the existing design procedures for buried structures constructed in an open-cut, the Department of Environmental Services (DES), Washington, D.C., in conjunction with Howard University, undertook a detailed study of Section II of the Capitol Hill Relief Sewer (CHRS). Inclinometers were used to measure lateral movements of the excavation wall and the total normal interface stresses acting on the concrete sewer were obtained using glotzl total pressure cells. This paper describes the results of the field instrumentation program for acquisition of data, their comparison with the design assumptions, and the results of a series of post-construction finite element analyses of the CHRS project.

Jan 1, 1979

By W. R. Reed, Y. Zheng

A recent study conducted by the National Institute for Occupational Safety and Health (NIOSH) evaluated the roof bolter canopy air curtain (CAC) systemin a blowing face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. This study evaluates the roof bolter machine CAC while operating in an exhausting face ventilation system. This study considers two similar locations to allow comparison with the previous blowing face ventilation (Zheng et al., Min Metal Explor 36(6):1115–1126, (2019)) study: (1) a roof bolter machine bolting the roof at 20 ft (6.1 m) from the face and (2) a roof bolting machine bolting at 4 ft (1.2 m) from the face. The environment introduces 6.0 mg/m3 of respirable dust to represent the roof boltingmachine operating downstreamof the continuous miner. However, the exhausting face ventilation uses an exhaust curtain with 9000 cfm (4.25 m3/s) of air. Two roof bolter machine working positions are simulated with the use of dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8%. When the roof bolter machine operated close to the face, increasing CAC airflow was required for adequate protection since the dust reductions can be as low as 39.5%. Additional CAC airflows of 350 cfm(0.17 m3/s) and 450 cfm(0.21 m3/s) were evaluated and demonstrated that dust reductions increased to 59.7% (350 cfm) and 72.0% (450 cfm) for the worst location where the roof bolter operators located.

Aug 26, 2020

By J. C. Fox, V. L. Ketellapper

The Summitville Mine, located in the mountains of Southwest Colorado, is an abandoned gold mine. From 1984 to 1992, Summitville was mined for gold using an open pit heap leaching technology. During this period, the volume of acid mine drainage released from the mine significantly increased. This was attributed to the development of the mine pits, the waste rock piles, the heap leach pad, and increased discharges from the drainage adit. The release of this acid mine drainage resulted in the destruction of the aquatic ecosystem for more than twenty miles downstream of the mine. Beginning in 1993, plans were implemented to reduce the amount of acid mine drainage released from the mine. The majority of this work has been completed at the mine. This work includes removal of the Cropsy Waste Pile, closure of the Heap Leach Pad, and revegetation of disturbed areas. Significant improvements to water quality downstream of the mine have occurred resulting from mine reclamation. Aquatic life has returned to portions of the previously mining impacted areas. This study discusses the actions taken to reduce the amount of acid mine drainage generated at the Summitville Mine, the costs of these actions and the resulting reduction in metal loadings. Over 250 samples taken at over 10 locations since 1993 form the basis of this evaluation. Copper loading is analyzed as an indicator of the effectiveness of the actions taken.

Jan 1, 2002

By Staff

"In 2014, the estimated value of total mine production of nonfuel minerals in the United States increased. The quantity of production increased for most mineral commodities mined in the United States, as did prices. Notable exceptions were the declines in prices for most precious metals. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Following the reduction in construction activity associated with the 2008- 2009 recession that continued through 2011, the construction industry continued to expand in 2014, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction. Other segments of the nonfuel minerals industries increased as well. Trends in other sectors of the domestic economy were similar to those for industrial mineral production (Table 1).Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals. Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. The materials with the highest unit values, usually metals, tend to have very low production rates compared with those of many low-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the minerals industry in general, the value of production is used rather than tonnage produced. Although the value of metals and industrial minerals mined in the United States are similar, if tonnages are compared, construction aggregates dominate, dwarfing the production of all other minerals combined.Mineral industry performanceThe estimated value of nonfuel mineral raw materials, including metals and industrial minerals, produced at mines in the United States in 2014 was $77.6 billion, a 3.5-percent increase from $75 billion in 2013 (Table 2). Net exports of mineral raw materials and old scrap were $15 billion (Fig. 2). Domestic raw materials, along with domestically recycled materials, were used to process mineral materials worth $697 billion. These mineral materials, including aluminum, brick, copper, fertilizers and steel, and net imports of processed materials (worth about $41 billion) were, in turn, consumed by downstream industries with a value added estimated to be $2,530 billion in 2014.In the United States in 2014, mine production of each of 14 mineral commodities was worth more than $1 billion. These were, in decreasing order of value, crushed stone, copper, gold, cement, construction sand and gravel, iron ore (shipped), industrial sand and gravel, molybdenum concentrates, phosphate rock, lime, salt, zinc, soda ash and clays (all types)."

Jan 1, 2014

By D. H. Desy

This research was undertaken to establish the lncendivity of aluminum alloys against rusty steel under frictional impact conditions at typical coal mine fan speeds, to determine any differences in incendivity among various aluminum alloys, and to Investigate less incendive materials as substitutes for aluminum alloys. With a specially designed apparatus, three aluminum casting alloys and three constructional steels were tested for incendivity in frictional impact against rusted steel in flammable methane-air mixtures. Although varying in degree, all aluminum alloys investigated exhibited a high ignition probability under the test conditions; none of the steel specimens tested caused any ignitions under the same conditions.

Jan 1, 1973

By C. R. McKee

In-situ mining of hard rock deposits will only become successful as we understand the engineering parameters involved and the design limitations they impose. As recognized by Wadsworth1 the most critical area is the enhancement of permeability in a hard rock mass. Along with creating permeability, the appropriate flow and fragment size conditions must be generated to insure economic rates of mineral recovery. In this article our interest is confined to true in-situ processes in which boreholes are drilled from the ground surface or a mine drift to deeper strata. We assume that fractures and permeability enhancement will be due to explosives detonated in boreholes. Other techniques such as hydraulic fracturing do not produce the necessary size distribution to promote economic extract ion rates unless the medium is already highly fractured and interconnected. Notable exceptions where hydraulic fracturing is applicable are many oil, gas and salt deposits. For many in-situ processes, an array of explosive charges offers the opportunity of creating a distribution of many fractures not achievable by other techniques. Such a situation would be suitable, for example, to in-situ mine hard rock gold, uranium, copper or oil shale deposits and may enhance oil and gas recovery in certain situations. The purpose of our article is to review and extend the explosive permeability theory of McKee and Hanson 3,4,5 and to apply its results to derive design parameters suitable for in-situ mining.

Jan 1, 1981

By Rafael C. Castro

As part of its risk management plan, the South Central Connecticut Regional Water Authority (RWA) is assessing the condition of its system of raw water conveyance tunnels and connecting pipelines. In 2006, the RWA inspected one of the system?s main tunnels, a 4-mi, 1950s-era tunnel that had not been inspected since its construction. The inspection team prepared extensively for the unknown conditions in the tunnel, and the inspection was completed safely and successfully. This paper describes the team?s pre-entry preparations, dewatering and ventilation efforts, surface-to-tunnel communication, access, physical inspection of the tunnel, and the lessons learned throughout the process. Additionally, this paper will preview planning for the subsequent inspections.

Jan 1, 2008

By R. J. Pugh

The coagulation of dispersions of weakly magnetic oxide mineral ultrafines (such as natural hematite or chromite) in an external magnetic field can be described from inter-particle forces. Essentially, coagulation occurs when the short range London-van der Waals interactions and the long range magnetic forces outweigh the stabilizing electrical double layer repulsion. From the classical colloid chemistry theory, we have calculated the various components of the potential energy for different sized particles at a series of ionic strengths and magnetic field intensities. We have related this theoretical analysis to experimental studies where the magnetic field-induced coagulation of ultrafines of natural hematite and chromite in aqueous suspensions was investigated using a laboratory scale electromagnetic solenoid. The experimental results relate the coagulation process (as determined by magneto-sedimentation analysis) to the particle size, the slurry pH and the external magnetic field. In the magnetic fields, maximum coagulation occurred near the pH of zero point of charge (pHzpc) of the minerals (where the electrostatic double layer repulsion was reduced to a minimum) enabling the particles to enter the "primary minimum" energy sink. On the other hand, in cases where the electrostatic repulsion was not suppressed, then the long range magnetic forces enabled coagulation to occur in the "secondary minimum". This caused the formation of chains which appeared to be relatively stable during sedimentation.

Jan 1, 1993

By J. M. Mutmansky, Y. J. Wang

The usual method employed to determine the direction of flow in a connecting airway in advance is to conduct a survey between the two existing nodes being connected by means of the new airway. It is then assumed that airflow will take place from the node with higher pressure to the node with lower pressure. The purpose of this paper is to examine this direction-of-flow problem -- using properties of the system characteristic curve for a two-terminal network -- and specify some conditions that ensure that flow will take from the higher-pressure node to the lower-pressure node. It is concluded that the only requirement is that all characteristic curves of fans in the network should be strictly decreasing. Five numerical examples illustrate some important properties of the direction-of-flow problem.

Jan 1, 1999

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960's. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By J. Kretschmann, N. Nguyen

"The Vietnamese economic growth of more than 5% per year leads this country to an enormous demand for raw materials. In the duration of ongoing expansion, the big challenge in the coming decades will be to make this process as sustainable as possible when it comes to economic, environmental and social objectives. Risk management especially in occupational safety and health (OSH) in enterprises is one of the most important tools to achieve this aim. But until now, this has not been taken into priority by Vietnamese coal mining enterprises. Main reasons for this situation can be found in deficient legislative conditions and in non-synchronized risk management systems. In contrast, Germany has implemented an adequate legal system and the German mining industry has gained lots of experiences in risk management, especially in occupational safety and health. This paper seeks to point out specific challenges how to improve occupational safety and health in Vietnam by transferring and applying German methods and standards."

Jan 1, 2011

By L. "Andy" Anderson, Stephen N. Short, James E. Friant

Since the introduction of "boxhole" drilling in South Africa in 1973, the concept of a blind raise, drilled upward from below, has become an accepted mining practice. A combination machine, capable of constructing raises to a mining level below, or blind raising upward from a single setup position adds a further dimension in versatility. A machine with these dual operating modes was designated by The Robbins Company as the 53R and was introduced into the Western Deep Level Mines, South Africa in 1984. The unit is powerful (200 hp) and compact (18,000 lbs., in a 10 ft x 4 ft 5 inch x 4 ft 6 inch package). This paper describes the design considerations for the new machine, provides field data from early trials, and looks briefly at its overall market and potential.

Jan 1, 1985

The molecular structures of isobutyl xanthate (IBX), diisobutyl dithiophosphate (DIBDTP), O-isobutyl-N-ethyl thionocarbamate (IBETC), O-isobutyl-N-ethylcarbonyl thionocarbamate (IBECTC) and O-isobutyl-N-ethylcarbonyl thiourea (IBECTU) were fully optimized using density functional theory (DFT) at the B3LYP/6-31+G(d,p) level with the integral equation formalism for the polarizable continuum model (IEF-PCM) in the aqueous phases. The effects of the polar groups in these thiol molecules on their collecting performances were determined by the energies and compositions of frontier molecular orbitals and the atomic charge values. Our results indicate that the sulfur atom(s) in IBX, DIBDTP, IBETC, IBECTC, or IBECTU molecule is the centre of reactivity. And the collecting abilities of these reagents for copper sulfide minerals follow the order as: IBX > IBECTU ? DIBDTP ? IBECTC > IBETC, and the order of their selectivities against pyrite is suggested as: IBX < DIBDTP < IBETC < IBECTU < IBECTC. The theoretical analysis provides an insight into the collecting powers of these collectors, and offers an atomic scale approach to understand the experimental data available in the literature. Keywords:xanthate; dithiophosphinate; thionocarbamate; thiourea; density functional theory; structure-activity relationship; copper sulfide mineral

Feb 27, 2013

By Igor Gonzales G.

The Southern Peru Copper Corp. (SPCC) recently built an integrated copper project consisting of dump- and heap-leaching operations at its mine complex in Peru. The pregnant leach solution (PLS) containing the solubilized copper from the leaching operations is processed in a new solvent extraction/electrowinning (SX/EW) facility to produce high-purity cathode copper. The dump leaching and SX/EW facilities are located near the Toquepala mine site. The crushing and heap-leaching operation is located at the Cuajone Mine. The pregnant leach solution from Toquepala and Cuajone is pumped 35 km (22 miles) to the SX/EW plant at Toquepala. The SX/EW plant consists of three trains of solvent extraction (SX), a tank farm area and an electrowinning (EW) facility. The solvent extraction plant has a total PLS flow capacity of 3,210 m3/hr (113,360 cu ft/hr). The electrowinning facility has an expected long-term production capacity of 97 t/d(107 stpd) or about 35 kt/a (38,500 stpy) of cathode copper. However, present production exceeds the expected long-term by about 20%.

Jan 1, 1996

By Richard A. Grieve

A 63.5 metric tons per hour (70 TPH) demonstration coal preparation plant was constructed on the Iowa State University campus, Ames, Iowa, as a part of the Iowa Coal Project funded by the state of Iowa and administered through the Energy and Minerals Resources Re-search Institute. Processing equipment in the plant circuit includes a heavy media separator, concentration tables, separating and dewatering screens, and conveying equipment. Coal samples of size 907 metric tons (1000 tons) with sulfur contents ranging from 2.5 to 8.75% sulfur from seven mines in the state of Iowa have been pro-cessed in the plant. Sulfur reductions have averaged 35%. With ash reduction averaging 45%. Equipment for advanced fine coal beneficiation research is currently being installed in the plant to include a slurry pretreatment circuit, froth flotation, oil agglomeration, pelletization, hydrocyclones, advanced design thickener and disc filtration.

Jan 1, 1978

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept.9, 2006 at the Museum Convention Center in Leadville, CO. The four inductees are Earl H. Beistline (1916 to present), R.A.F. Penrose (1863-1931), Robert M. Reininger (1912-2006) and John Stanton (1830-1906). The inductions will bring to 193 the number of mining “greats” whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2006

By R. Snoby

Since its introduction in 2002, the modern air jig has processed a wide array of coals throughout the world. This paper explores the reasons and justifications for the installations and provides case history performance data. Specifically highlighted are air jig plants processing metallurgical coal in Colombia, bituminous coal in the United States and India and lignite in the United States and Spain. Each installation has unique reasons to justify an air jig facility. It is important to note that not all of the justifications were based on the ?most cost effective yield?, normally a mantra for coal preparation plant designers and owners. Dry jigging of coal has long been a proven technique for upgrading coal, the modern air jig, with its improved efficiency and operating systems simply extended the range of applications. In some cases, it even allows market quality coal to be produced when no other option is possible.

Jan 1, 2009

By W. L. Price

Recent publication of United States Bureau of Mines figures showed that the sand and gravel (3) industry is the largest single mining industry in the United States in term of yearly tonnage produced. The yearly production of over 500,000,000 tons per year now exceed bituminous coal production. This disclosure caught unawares many observers who have not been following closely the rapid-growth of this phase of mining. Along with this steady growth in production, the sand and gravel industry has gone through an accelerated and varied program of beneficiation in a period of the last ten years.

Jan 1, 1958

By J. Jorge, J. Mariño-Salguero, B. Álvarez-Rodriguez, J. M. Menéndez-Aguado, J. J. de Felipe

"This work focuses on the characterization of heat generation during dry fracture by direct impact of a tantalum ore. Moreover, an attempt was made to quantify the heat energy loss to the environment during the grinding process of a ball mill. The study was carried out using mineral samples from a Spanish mine that were characterized by measuring their density and specific heat. During the experiments, increases of temperature ranging from 5.9 to 7.3 °C after the fracturing process were observed. A numerical model was then applied to calculate temperature distributions through the mill wall. Three possible combinations of heat transfer coefficients were analyzed, from (1) Kapakyulu and Moys, (2) Duda and (3) the heat transfer laboratory of Universitat Politècnica de Catalunya. The models with the coefficients from Kapakyulu and Moys and the heat transfer laboratory of Universitat Politècnica de Catalunya were found to provide results that were in best agreement with the experimental data. IntroductionEvery year, several billion tons of metallic ores, minerals, cement and other solids used in the ceramic and chemical industries are subjected to size reduction in ball mills around the world. The U.S. Department of Energy (2005) reported that in the United States about 29 percent of the total energy used by the mining industry, or 0.4 percent of total U.S. energy consumption, is used in comminution. In Canada and Australia, comminution is responsible for about 2 percent and 1.5 percent of total energy use, respectively. In nonindustrialized countries where mining constitutes higher fractions of their industrial sectors, comminution costs represent a significant contribution to mine operating costs. The specific energy consumption values for the grinding of these materials typically range from 5 to 50 kWh/t. Thus, a significant amount of electrical energy is consumed in the ball mill grinding operation (Aguado et al., 2006; Gupta and Sharma, 2014). Grinding can represent up to 50 percent of the direct operating cost in a mineral processing plant, especially as comminution devices operate in highly inefficient ranges of 4 to 8 percent (Wang, Yang and Yu, 2012)."

Jan 1, 2017