Search Documents

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

Jan 1, 2006

By J. M. Mutmansky

Procedures for the determination of the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques has been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the multitudinous mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the solution of problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To establish a major simplification in the development of procedures for the determination of the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1984

By J. D. Pitts

The worldwide production of iron ores was approximately 880 million metric tons in 1975. This level is the result of an annual growth rate of nearly four percent during the period 1967 to the present. The high growth rate was particularly significant in that two relatively severe worldwide recessions occurred in 1971 and 1975. The current upturn in world economic growth will probably allow future annual iron ore production growth rates in excess of the four percent figure, and, in fact, the International Iron and Steel Institute (IISI) has predicted that a five percent rate should be realized through 1985. The IISI figures would indicate a 1.4 billion metric tons per year output by 1985 or an increase in current production levels of around 500 million metric tons per year (MMTA)1. Even the more conservative four percent growth rate prediction from historical data would provide an 2 increase over current figures of nearly 350 MA by 1985. A large portion of world iron ore production is being provided by large resource-rich countries with relatively new industrial bases. These countries are typified by heavy export of raw materials such as iron ore and ore products and a large capital investment in the facilities to recover these raw materials. Brazil and Australia are typical of such countries and, indeed, their production of iron ore in the period 1967 to 1973 increased at annual rates of 17 to 30 percent, respectively, The continual reassessment of resources in these and other major iron ore exporting countries such as Venezuela and Liberia would indicate chat these high growth rates may continue for some years to come to meet anticipated world demand for raw steel production.

Jan 1, 1976

By H. D. Dahl

In January, 1969, the Central Research Division of Continental Oil Company initiated a research program on roof control. The purpose of the research was to improve roof stability. Toward this end, it was necessary to determine which of the many geological and geometrical variables have a significant effect on roof stability. The isolation of these significant variables would allow research effort to be concentrated where it would be most effective in improving roof control. The research effort was directed toward two major objectives. One was to de-fine the geological and/or geometrical parameters that affect the severity of roof conditions in any particular area of the mine. This study was concerned with roof fall intensity. The second was to define why roof falls in Humphrey No. mine (and in northern West Virginia-south-western Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. This study was concerned with roof fall orientation. To provide a reference framework for further discussion, a geological description of the area is presented in Part II. In Parts III and IV, the procedures, methods, and 'results of the research applied toward the afore-mentioned major objectives are presented. Part V contains the conclusions and recommendations for-warded by this study.

Jan 1, 1971

By Robert G. Pinkerton

Boyles Bros. Drilling Co. and Gibbons and Reed Company, both of Salt Lake City, Utah, have successfully combined into two joint ventures on the San Juan-Chama project of the U. S. Bureau of Reclamation. The Azotea Tunnel is 12.7 miles in length; the inlet portal is on the Navajo River in Archileta County, Colorado, and the outlet portal is in New Mexico, about 10 miles south of the state border. The Oso Tunnel lies immediately to the north of the Azotea Tunnel and discharges water directly into it. We are presently driving both tunnels with mechanical boring machines from their portals at the Navajo River. Both tunnels are circular, fully concrete lined. The Azotea Tunnel has a finished diameter of 10 ft. 11 inches while the Oso Tunnel is 8 ft 7 inches in diameter. Both tunnels are supported with circular, structural steel rings as required by ground conditions. In good ground rock bolts and steel roof plates are used.

Jan 1, 1967

By Janet E. Lamarre

Current statistics show that 90% of new-business failures are caused by the unsuitability of the entrepreneur for the business he has started. Are you a suitable candidate for success as a consulting geologist? Should you start your own geologic consulting business, and when? This paper investigates the demand for consultants with respect to general economic trends and mineral exploration activity trends. Furthermore, the study reveals certain technical skills and personal characteristics important to the success of the consulting geologist. Research shows chat certain expectations which prompted geologists to change careers are fulfilled while other unanticipated expectations often are also met.

Jan 1, 1985

By Peter Riba

Up until ten years ago the industry had arrived at a relatively conventional, and consistent design of coke ovens. Through the years the designers and builders were not being heavily taxed to come up with revolutionary new designs. However, the stimulus for design change was ever present. These stimuli for change are quite important and they are the driving force which produce improvements. The most obvious stimulus to change a design is commercial. To "build a better mouse trap and the world will beat a path to your door" is the well used cliche which best befits this philosophy. As in all businesses, coke oven designs require that all of the considerations, which affect the cost or the desirability of the design, be optimized. One way to increase the desirability of the particular design, 1s to make the design in- expensive to operate. Or, put another way, to increase production for the same operating cost

Jan 1, 1980

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 feet and diameters of over 30 inches have become numerous and widespread. Fifty such holes have been drilled for access shafts to LPG mined caverns, Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-inch diameters with 1600-foot depths, 120-inch diameters with 570-foot depths, and 72-inch diameters with 4800-foot depths. Equipment is now available to drill a wide range of ?big holes? for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of "big holes". The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The illustrations to be presented concurrently with this paper show the various equipment and accessories now in use. (See Appendix I for captions of illustrations.)

Jan 1, 1966

By Charles A. Gargano

The current state of the mass transit industry in America will be examined. How and why this important urban activity shifted entirely, or almost entirely, from the private sector to the public sector. Who pays for transit? For day to day operating costs? For capital investment? The prospects for transit's future will be the next major issue addressed. In a word, they are rather good. Over the past decade there have been major new transit investments made in Atlanta, Baltimore, Washington, D.C. and Miami, as well as constant re-investment in such cities as New York, Boston, Philadelphia and Chicago. While the current administration has put a temporary halt on the initiation of any major new rail transit projects using Federal funds, there are several mechanisms localities have for using other resources for such projects. These will be explored.

Jan 1, 1983

By Whitmell J. Smithwick

Lime is one of the most extensively used chemicals in industry. Other than sulfuric acid, it is used in greater quantities than any other man-made industrial chemical. In 1974 there were 20,368,000 tons of lime used in the United States, which amounts to approximately 190 pounds for each man, woman and child in our nation. Lime also is perhaps the most diversely used of any industrial chemical. It is used in such areas as pharmaceutical, chemical, steel making, glass making, production of copper and aluminum, sugar refining, agriculture, construction, ecological endeavors, potable water treatment and sanitation. Figure I lists the major uses of lime for 1974, which is the latest year for which this data is available. The impact of the use of lime for ecological reasons did not show up to any appreciable extent in 1974, but we expect this to be a significant factor within the next few years. Fortunately, in the United States and also in most of the world, there are many deposits of high quality limestone available for the production of hood quality lime. For this discussion, we will assure that a limestone of a suitable quality and size consist will be available in a storage bin or stockpile near the kiln. Quality requirements for the lime product will be covered. We also will give a brief description of the three most popular types of lime calcining systems, how they function, and expected lime product quality from each of these. Commercial fuels and major accessory equipment will be discussed briefly.

Jan 1, 1976

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2018

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2017

By C. Frenzel, N. Blechschmidt

"INTRODUCTION There is no doubt about the time and effort companies put in establishing and maintaining their equipment. However, the question about how these companies can map the benefits comes up. Neither do they have the tools to quantify the benefit of their action, nor do they have the tools to know the actual quality of their current maintenance system. The resources used in the process seem futile to observers. It seems impossible to trace improvements and to get information about the impact of actions in retrospect. Improvements in maintenance performance cannot be recognised by management or shareholders. Thus the necessity for measuring the performance of maintenance systems is given. In this paper ConMoto is systematically showing the strengths and weaknesses of many companies' maintenance management and is providing field-tested proven design elements for measuring maintenance systems and implementing Value Oriented Maintenance. Considering only business assets in production facilities and related machinery out of all investment goods in Europe, you reach a value of around 9.7 trillion euros in 2008. In Germany alone the equipment replacement value amounted to about 1.9 trillion euros [8,10,11,13]. If you calculate a cross sector maintenance costs rate of 4.8 % (corresponding to the average value identified in this study), direct maintenance costs in European production locations add up to over 450 billion euros per year [3]. These figures speak for themselves. Yet maintenance is not only of enormous significance for European enterprises. Our experiences show that maintenance and asset management, particularly sustainability issues, are also increasingly moving to the forefront in the BRIC states, in the Middle East and in many emerging countries. First of all, in order to meet the resulting high quality and cost related requirements of maintenance systems, a comprehensive overview of the issue is needed. This overview is provided by a detailed analysis of 83 companies and production plants from various sectors – with amazing results. SIGNIFICANCE OF MAINTENANCE Current studies show the high financial significance of maintenance and asset management. According to the market study in the Asset Manager [9], in industrialised countries about 10 to 15 per cent of the labour force are employed in maintenance and facility management tasks. In Europe about 40 to50 million people are directly and indirectly involved in retaining the value of machinery, plants, buildings, transport systems and infrastructure facilities. A glance at the costs side also demonstrates the great relevance of maintenance. EU-wide annual direct maintenance costs amount to a total of more than 1,500 billion euros. In Germany alone they are about 250 billion euros. This impressive total is considerably exceeded by indirect maintenance costs caused by technical failures. Indirect costs are estimated to be five times higher (Figure 1). [7,12,14]"

Jan 1, 2018

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.

By William A. Macaitis, Frank E. Dalton, Leo R. DiVita

The Metropolitan Water Reclamation District of Greater Chicago's Tunnel and Reservoir Plan (TARP) is a multi-purpose urban public works project with a total cost of $3.7 billion. Currently 51 miles of TARP tunnels are completed and operational and 34 miles are under construction. The excavated TARP tunnels have been constructed in rock utilizing 29 tunnel boring machines, ranging in size from 6.5 to 35.3 feet in diameter.

Jan 1, 1993

By F. Shigeyoshi

The development of pelletizing during the last ten years has continued, however, self-fluxing pellets have not been regularly and commercially produced for use in blast furnaces, except as Kobe Steel, Ltd., Japan. This paper tells about unique developments for self-fluxing pellets, and their effects when used in Kobe Steel's No. 3 blast furnace at the Nadahama Works (inner volume 1845 Nm3, hearth diameter 9.5 m)., Several phases of the pelletizing process are discussed individually, and also their relation to performance in blast furnace operation. Special emphasis is placed on proper preparation of the limestone added to the raw materials, and indurating at optimum conditions. Means of improving pellet quality by correct control of size distribution of the raw materials used in pelletizing, and indurating temperatures, are also discussed. As basicity (CaO/SiO2) of pellets increased 0. 1, coke consumption decreased 3. 8 to 4. 2 kg per ton of hot metal, when using 70% pellets in the iron burden.

Jan 1, 1969

By T. A. Ring

The bed filtration of colloidal particles has been modeled by performing a differential particle balance. The balance considered the localized particle deposition rate to be the sum of three rate resistances: 1) mass transfer to a region near the surface; 2) adhesion onto a partially filled surface; and 3) resuspension from a partially filled surface. The differential particle balance equations, one for the free particles and one for the adhered particles, were solved by a finite difference algorithm. The results of this model are compared to experimental filter breakthrough curves.

Jan 1, 1983

The 29th annual American Mining Hall of Fame Awards Banquet and Fundraiser sponsored by the Mining Foundation of the Southwest (MFSW) will be held at the JW Marriott Star Pass Resort, Tucson, AZ on Saturday, Dec. 3, 2011. Each year, one living inductee, two recipients of Medals of Merit, and up to five honorees from mining history are chosen by the MFSW for their outstanding contributions to the mining industry. Chilean Minister of Public Works and former Minister of Mining, Laurence Golborne Riveros will be the guest of honor, featured speaker and inductee into the American Mining Hall of Fame. Golborne Riveros was instrumental in managing the rescue of the 33 Chilean miners in October 2010 and in the coordination/management of the ?townsite? for family members, rescue support and the media. His engineering background and executive management skills made him ideally suited to assist in both a technical and managerial role in this emergency.

Jan 1, 2011

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983

By J. A. Herbst

Fine coal cleaning by froth flotation has become common practice in the U.S. with more than 80,000 tons treated in this way per day. In spite of this large tonnage, developments in the automatic control of coal flotation circuits have lagged significantly behind those for mineral systems. One reason such developments have been limited is that instruments have not been available for the on-line measurement of carbon or ash and another critical variables in coal slurries. A second reason is that the influence of the operating variables on coal flotation has not been completely understood. During the last few years some of the required instrumentation has been developed and an improved knowledge of the flotation process itself has occurred through mathematical modeling; as a result certain control strategies for coal flotation are beginning to emerge. This paper attempts to evaluate several control strategies using a detailed flotation dynamic simulator, DYNAFLOAT. After constructing a process matrix for the system of interest, promising alternatives for linking manipulated and controlled variables have been analyzed. In order to develop combined grade and recovery control strategies, the authors found it necessary to construct a grade/recovery map with the aid of the simulator to drive the system to known final, feasible grade/recovery operating conditions. Finally, an advanced strategy which uses an on-line model to identify disturbances and take control actions is proposed.

Jan 1, 1983