Search Documents

By C. Liu, F. Ye

"To extend the variety of lump ores that are used in the COREX shaft furnace and to optimize iron ore blending, the original evaluation method for iron ores that was proposed by Voestalpine AG has been improved. Physicochemical and metallurgical properties of iron ores, including Sishen lump ore and CVRD pellets, which are currently used in the COREX process, and three other lump ores, were assessed and compared. Ore matching principles were proposed and five optimized iron ore blending schemes designed and verified by laboratory experiments to prove the effectiveness of the improved evaluation method. The replacement of Sishen lump ore by the alternative L2 and L3 lump ores without varying the proportion of CVRD pellets could improve the degree of reduction and rate of metallization, and decrease the bonding index. Based on the results of laboratory test work and industrial- trials, an ore blending scheme of 60% CVRD, 20% L2, and 20% L3 is recommended for use in the COREX process. IntroductionIn recent years, problems such as environmental pollution and a shortage of coke and coal resources for blast-furnace ironmaking have become increasingly apparent. Based on sustainable developments in the iron- and steelmaking industries, the environmentally friendly COREX smelting-reduction process with low energy consumption was developed and introduced (Zhou and Du, 2013; Song, Lv, and Yin, 2015; Xu et al., 2016; Kurunov, 2010). The evaluation system for lump ore that was proposed by Voestalpine AG recommends that only Sishen lump ore from South Africa be used in the COREX process, because of the stringent physicochemical and metallurgical property requirements. This situation significantly hampers improvements to the technical and economic aspects of the COREX ironmaking process, especially in China (Eberle, Siuka, and Bohm, 2006). No theoretical or technical basis has been provided for the evaluation system, and the assessment approach for iron ores also presents problems that need to be discussed and resolved.The COREX process consists of two reactors: the prereduction shaft furnace and the melting gasifier as shown in Figure 1 (Wu et al., 2017). Pellets and lump ores which are charged to the prereduction shaft should have a good reducibility and metallization with a low degradation index (Li et al., 2016; Wu et al., 2011; Kumar et al., 2009; Kang, Gupta, and Sahajwalla, 2007). The properties and microstructure of the iron ore pellets which are required to achieve a high productivity and a lower fuel rate in the COREX process have been investigated (Umadevi et al., 2011). Some efforts have also been made to investigate the behaviour of lump ores in the COREX shaft furnace, including the disintegration characteristics and the reduction degradation (Umadevi et al., 2011; Zhou et al., 2015; Xu et al., 2013; Li, Feng, and Zou, 2013; Hou et al., 2014). However, few studies have focused on the optimization of ore blending for partial or total substitution of the expensive Sishen lump ore by other, cheaper lump ores to reduce the production cost. The technology for the utilization of blended lump ores in the COREX process is still in its early development stages (Zhou et al., 2017; You et al., 2017)."

May 1, 2019

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By A. Rödfalk, P. Bloemer, J. P. Nilsson, N. Brogden

"Reliable and accurate metal transfer information during silicon tapping from an EAF is invaluable for decision-making and process optimization, while obtaining such information safely is a necessity.Elkem Thamshavn Norway, a producer of metallurgical-grade silicon, identified inherent safety problems with gauging fill levels in ladles using dip bars while molten metal was continuously pouring from a rotating EAF. Operator safety was a paramount concern, and an alternative automatic method of controlling the tapped fill level needed to be found.It was also considered that further benefits could be achieved such as monitoring the tapping flow from the EAF in order to identify any clogging, as well as the potential to use the live feed from such a system to assist decision-making regarding work around the taphole area.Agellis Group AB, Sweden, a company with over 30 years of experience in gauging molten metal levels in the metals industry, was able to design a solution for Elkem Thamshavn that would provide the required real-time process data while enhancing operator safety.This paper shows how the Agellis AB EMLI-L system was successfully installed at Elkem Thamshavn’s EAF continuous tapping area, how ladle fill levels were constantly monitored, and how full ladles were replaced by empty ones without the need for operators to be in the tapping area to take level readings. The results were used to compare the accuracy and reliability of Elkem Thamshavn’s current measuring methods with that of the EMLI-L system. The paper also covers how problems such as how to connect, run, and protect cables in and around the EAF tapping area, as well as connector and cabling survivability during the three day refractory pre-bake period, were solved. Finally, the paper discusses the potential production improvements, maintenance requirements, and data integration attainable through the installation of the system, as well as the major safety improvements that have been achieved."

Jan 1, 2014

By B. X. Huang

Hydraulic fracturing technology is presented as a solution to improve permeability and thus solve the extraction problem of coal seam gas in low-permeability gas-bearing coal seams. Given an existing group of original cracks, the propagation of main hydraulic cracks and hydraulic wing cracks was simulated using realistic failure process analysis software. The process represents the structural transformation of hydraulic fracturing and permeability improvements caused by it. In addition, a field test for improving the permeability of gassy coal seams by hydraulic fracturing was also conducted. The propagation of the main cracks and wing cracks by hydraulic fracturing forms a network of original joint cracks, hydraulic wing cracks, and main hydraulic cracks, which improve the permeability of the coal seam. High-pressure water in the drill hole and in the main hydraulic cracks permeates the two flanks of the hole, forming the permeating water pressure. With an increase in drill water pressure and an extension of the main hydraulic cracks, the permeating water pressure on both sides of the main hydraulic cracks in the coal mass also increases. Hydraulic cracks tend to form connections through rock bridges. The extension of hydraulic wing cracks through connections in the rock bridges between the cracks transforms the rock mass to a fractured structure and improves its permeability. Hydraulic fracturing technology for improving permeability in underground conditions can increase the amount of gas drainage by a factor of 15. A stress relief area develops at a radial distance of 10-2.0 m from the hydraulic fracturing drill hole, while an area of rising stresses, called the pressurized area, develops a further 15 m away from the pressurized hole. Practice has proved the existence of the stress transfer phenomenon and the high stress area after fracturing. This kind of hydraulic fracturing technology is more effective in holes drilled from underground than in surface drill holes, with respect to costs and controllability, and is therefore the major trend in gas drainage development in coal mines.

Jan 1, 2012

By Y. Qin, L. Han, P. Gao, Y. Han, Y. Lia

In the present study, an innovative comminution technology of high-voltage pulse discharge was proposed for galena to weaken the mechanical property. The results of pre-treatment experiments indicated that the optimal operating conditions of spherical gap spacing 25 mm, pulse numbers 120, and loading voltage 25 kV were obtained, where the relative grindability of pretreated products was improved significantly, although with the prolonging of grinding time, the superiority of high-voltage electric pulses was gradually weakened. The galena ores were subjected to a high-voltage pulse discharge, and then the crack generating along the boundary between galena and gangue was observed under an optical microscope, and the surface burning which appeared in the ores. The scanning electron microscope (SEM) results indicated that the pretreated products were in a state of melting and then condensation, accompanied by some pore formation. Pulsed discharge pre-treatment not only produced more micro-cracks and cracks in the sample but also extended the original crack. Keywords: High-voltage pulse discharge; galena; relative grindability; micro-crack

Jan 1, 2020

By G. C. Lindeque

"A downward trend in tyre life on haul trucks at an open pit iron ore mine prompted an investigation into the current tyre management strategy in order to improve tyre life. ‘Best practice’ was compared to the current tyre management strategy at the mine to determine aspects that could be improved. Aspects that showed significant room for improvement included employee tyre awareness, tyre pressure maintenance, and road conditions. For each of these aspects a plausible alternative was suggested.A new tyre management strategy was formulated as a step-by-step guide on how to implement the proposed changes. Each step introduces new initiatives but at the same time builds on the previous step’s success. A sensitivity analyses was performed to determine the impact of the proposed changes, with the variables being the reduction in the percentage of premature tyre failure, and the reduction of the site wear rate.The ‘most likely’ scenario showed an increase in tyre life of 41% for the Komatsu 730 trucks and 105% for the CAT 777 trucks if the entire tyre management model is implemented. This would result in a possible annual saving related to tyre usage of R9.2 million. OverviewThe study focused on the tyre life on the main haul fleet at an open pit iron ore mine. The haul fleet consisted of 17 Komatsu 730 (180 t) haul trucks and 12 CAT 777 (90 t) haul trucks.The haulage operation consists entirely of tyre-based haul trucks. Five per cent of the total mining budget is related to tyre costs. Since 2012 there has been a steady decrease in tyre life as measured in operating hours (Figure 1) due to the high percentage of tyres that fail prematurely. In 2014 a total of 41% of all tyres failed prematurely and 61% were classified as ‘worn out’."

Jan 1, 2016

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining Industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of ?Google maps?? underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum?s new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2012

By I. B. Fernandes, M. A. Reuter, A. Abadias Llamas

Metallurgical simulation and evaluation of the resource efficiency of whole production processes are of key importance for impact assessment, in terms of environment and resources. Exergy is a measure of resource consumption, taking into account energy, raw materials, water, and chemicals; which allows for the evaluation of different technologies to find the most resource efficient and environmentally friendly process. This paper compares the sustainability for production of rare earth magnets from primary and secondary resources through an exergetic evaluation of the production process, in addition to traditional life cycle assessment (LCA). The methodology makes use of simulation tools for tracking material flow and resources used, based on thermodynamic laws, from ore exploitation to magnet production and recycling. It highlights areas with the greatest potential for improvements in terms of resource consumption and environmental impact generation, having a thermodynamic-validated flowsheet for primary and secondary production of NdFeB magnets, present in several low-carbon technologies, such as wind turbines, electric vehicles, and cooling systems. It demonstrates the minimum exergy destruction for magnet production, through an irreversibility breakdown chart, showing where irreversible material and energy losses occur. Results show that CO2-equivalent emissions for producing NdFeB permanent magnets from primary resources could be twice as high when compared to magnets produced from recycling technologies. The theoretical maximum exergetic efficiency for primary production is 57.61%, whereas for permanent magnets produced from secondary resources, the exergetic efficiency reaches up to 82.89%. Two magnet recycling technologies were evaluated, i.e. in acidic medium and via hydrogen decrepitation, and it was observed that their exergetic efficiency and environmental impact performed better than production from primary resources. Keywords: Resource efficiency, exergy analysis, permanent magnet recycling, process simulation, system design

Jan 1, 2020

DD3-tunnels (PD BH's) ? Rotary coreholes 111no. (124) ? Percussion holes Ono. (37) ? Sampling (rock and soil) ? Soil and rock permeability ? testing ? BH Televiewer Surveys [ ]

Jan 1, 2007

Metso Minerals Cisa have developed VisiofrothTM - a system which calculates parameters of the froth surface using vision from remote cameras mounted about individual flotation cells. The parameters calculated from this system can be utilised within process control strategies to achieve stabilisation or optimisation of the flotation process. As part of a JKMRC AMIRA P9 field campaign, froth vision was collected from various cells operated at different air rates and froth depths within Rio Tinto's Northparkes copper roughing and scavenging circuit. At the same time, samples were collected to determine the cell metallurgical performance at each operating condition. These froth images have been processed using the VisiofrothTM system with froth velocity, bubble size, froth collapse rate and various froth colour parameters calculated. These parameters have been compared to the measured concentrate flow and concentrate grade produced at each condition. This analysis shows that the concentrate tonnage flow is strongly correlated with froth velocity whereas the concentrate grade is best correlated using froth velocity in combination with a bubble stability parameter which affects the bubble size distribution on the top surface of the froth. This paper summarises the results from this analysis as well as an overview of the VisiofrothTM system and the parameters that are measured by the software.

Jan 1, 2007

By A. Singh, K. Bisaka, G. Marape, T. Mokgomola

This paper investigated the pre-concentration amenability of sovite (carbonatite) ore to enhance the grade of rare earth elements (REE) bearing minerals by rejecting calcite, and to improve total rare earth elements (TREE) recovery using gravity and magnetic separation. A high proportion of calcite affects downstream processes like leaching due to high acid consumption. Multiple flowsheets combining gravity and magnetic separation were employed to target > 60% TREEs recovery to the final concentrate and > 60% calcite rejection to the tailings. Head analysis of the feed showed the sample’s main constituents as Fe (15.61%), Ca (16.04%), SiO2 (7.13%), and lastly TREEs (1.12%). Mineralogy liberation data at 2mm top size indicated poor liberation of TREEs, with the majority of minerals displaying < 30% mass greater than 80% liberated. Grain size distribution data showed that the majority of REE minerals are fine grained and report to the < 20 μm size class. Calcite liberation mineralogy showed < 60% mass greater than 80% liberation.A combination of a single-stage shaking table with a wet high intensity magnetic separator at a magnetic intensity of 7520 G was found to be the optimum flowsheet. For a shaking table feed with P80 of 150 μm followed by tails regrind to P80 of 45 μm as feed to wet high intensity magnetic separator, the overall mass balance results showed that 60.5% TREEs are recovered to the concentrate while 63.0% calcite is rejected to the tails. However, due to the fine-grained nature of This paper investigated the pre-concentration amenability of sovite (carbonatite) ore to enhance the grade of rare earth elements (REE) bearing minerals by rejecting calcite, and to improve total rare earth elements (TREE) recovery using gravity and magnetic separation. A high proportion of calcite affects downstream processes like leaching due to high acid consumption. Multiple flowsheets combining gravity and magnetic separation were employed to target > 60% TREEs recovery to the final concentrate and > 60% calcite rejection to the tailings. Head analysis of the feed showed the sample’s main constituents as Fe (15.61%), Ca (16.04%), SiO2 (7.13%), and lastly TREEs (1.12%). Mineralogy liberation data at 2mm top size indicated poor liberation of TREEs, with the majority of minerals displaying < 30% mass greater than 80% liberated. Grain size distribution data showed that the majority of REE minerals are fine grained and report to the < 20 μm size class. Calcite liberation mineralogy showed < 60% mass greater than 80% liberation.A combination of a single-stage shaking table with a wet high intensity magnetic separator at a magnetic intensity of 7520 G was found to be the optimum flowsheet. For a shaking table feed with P80 of 150 μm followed by tails regrind to P80 of 45 μm as feed to wet high intensity magnetic separator, the overall mass balance results showed that 60.5% TREEs are recovered to the concentrate while 63.0% calcite is rejected to the tails. However, due to the fine-grained nature of TREEs, no flowsheet improved their grade.

Nov 6, 2024

By T. Mützea, L. Schützenmeister, G. Kacheb

High-Pressure Grinding Rolls (HPGR) are employed in cement plants worldwide. Although the technology has been mastered in the majority of applications, design-, scale-up- and operationalchallenges still exist today. In addition to modelling throughput, energy requirement and comminution success, the prediction and avoidance of malfunctions is of great importance in current research. The performance of the mill is highly influenced by the roll speed and the fineness of the feed material. Another parameter influencing the composition of mill feed is the circulating load, which is determined by the grinding circuit configuration, the target fineness and the separation efficiency of the classifier. In order to meet this circumstance and simultaneously maintain a reasonable level of material input and testing effort, a complete grinding circuit on a small technical scale was set up in the research centre of Thyssenkrupp Industrial Solutions AG. The present study varied the roll speed (0.5-2 m/s) and the proportion of fines in the feed (0-75 %) in order to investigate the influence of both parameters on the finish grinding of a Portland cement with a target fineness of 4000 cm²/g according to Blain. The experimental results are compared with model concepts and critically examined with regard to their transferability to industrial plants. Keywords: Cement grinding, grinding circuit, HPGR

Jan 1, 2020

"Chairman: Professor C. O. Frush Rapporteur: Mr A. C. SchmidtPapers:Planning of underground copper mining by J. K. Williams, L. Smith and M. P. WellsLinear programming models of copper leach and solvent extraction plants by W. P. C. Duyvesteyn, J. R. Cutland and J. R. L. RusselPlanning and forecasting stope production by D. W. Kappes and P. F. X. Moussett-JonesA proposed method of dynamic ore reserve assessment for a caving system of mining by A. F. Spinks and S. P. NicholsThe initial point made by Mr L. Smith in presenting his paper was that the planning aid outlined in the preprint was neither sophisticated nor complicated. However, it was a system which worked and was a very real way in which the computer was being used to assist miners, in particular, who at the present moment have very little experience in the use of computers.Mr Smith apologised for the fact that the editors of the paper had eliminated all reference to &apos;time&apos;. This was very unfortunate because the essence of the system was that it saved time, which was one of the main points made in the paper.The operations being planned by this means cover the Rokana orebody which is a stratiform body mined by open stoping.The planner has to decide how much ore to mine from each base in each time period of his plan, that is, from three to four months hence to a year ahead. Normal procedure is for the planner to have discussions with the underground manager on some of the information he requires. The sort of information needed is (i) tramming limits for each face, (ii) extraction and grade factors, (iii) the present status of mining operations so that the planner knows where to start the new plan, and, (iv) details of any other mining consider¬ations that need to be incorporated in the plan.The objective at this point is to produce an initial plan for discussion purposes. All the information required comes from one sheet per stops and shows, inter alia, the stope identifier, the length along strike, the ore tonnage, the copper and cobalt grades and, finally, the extraction and grade factors.The program itself, among many other things, checks the data for validity, compatibility, completeness and credibility and prints error messages accordingly. Output from this system is in the form of a summary of production from each face, as well as giving the figures of ore reserve depletion. This summary indicates which slopes are to be mined in this time period, the original survey grades (copper and cobalt), the estimated production grades, how much is to be mined from each stope and the copper and cobalt production accordingly."

Jan 1, 2014

By Thomas V. Fame, William E. Porter

"As geological and mining conditions become more complex, and as overall mining economics become more marginal, short- and long-range decision-making regarding multiple-seam surface mining becomes more difficult. The decision-making problem involves a study of economics, cut-off grades and ratios, equipment capabilities, sequencing and selective mining practices.This paper is concerned primarily with multiple-seam mining of bituminous coal. The research has led to the development of an economic decision-making model for use as a day-to-day tool to aid mine operators and pit geologists to decide what and how to mine.The model is designed as an aid for feasibility decision-making in multiple-scam situations and for situations where selective mining is needed or desired. In effect, a simulation of the feasibility and preliminary mine planning phases has been developed. The model is divided into four separate segments: decision-making, simulated mining, cost calculations and the determination of the discounted cash flow return on investment."

Jan 1, 2014

By I. O. Ondicho, E. K. Mutinda, B. O. Alunda, E. Agyekum

Driven by the necessity to improve blast performance regarding fragment size distribution in limestone mines, this paper introduces the prediction and measurement of blast fragmentation distribution through the modified Kuz-Ram (MKR) and Kuznetsov-Cunningham-Ouchterlony (KCO) models. Precise prediction and measurement of rock fragmentation resulting from blasting play a critical role in hard rock ore extraction. This is due to the substantial influence of post-blast ore size distribution on the efficiency of all subsequent downstream rock handling and processing operations. Additionally, employing secondary breakage of boulders, when necessary, leads to an unjustified rise in production costs. In this paper, the MKR and KCO models were utilised to identify the most appropriate model for application in Bisil and Simba quarries situated in Kajiado County, Kenya. Split-Desktop was used for blast fragment measurement by processing digital images obtained after blasting and computing the fragment size distribution of the blasted rock. As per the investigation, the recorded percentages of boulders generated at the sites ranged from 7% to 12.3% for the Simba quarry and from 11.2% to 23.9% for the Bisil quarry, respectively. Regression, correlation, and root mean square error (RMSE) were employed as the primary performance indicators. The study concluded that KCO outperformed MKR in accurately predicting blast fragment sizes in the examined quarries.

Mar 5, 2025

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best `grade descriptor&apos; is discussed.

Jan 1, 2007

By G. Akdogan, C. Dorfling, L. Bumhira

Hydrometallurgical recovery of rare earth elements from phosphors obtained from end-of-life fluorescent lamps involve leaching followed by extraction of dissolved metals from solution. The similar properties of rare earth elements make selective recovery of individual elements challenging. The aim of the paper was to investigate the extraction of primarily Ce and Tb from a hydrochloric acid leach solution also containing other REEs (Y and Eu) as well as impurity metals (Ca and Al). Batch solvent extraction tests were performed with di-(2-ethylhexyl) phosphoric acid (DEHPA) at various extractant concentrations, pH conditions and organic-to-aqueous ratios. Extraction isotherms and separation factors for the range of conditions tested in the project are presented in the paper. Separation of individual REEs was not possible at the conditions investigated, but a mixed REE product can be obtained in a single extraction stage operated at a pH of 0.5 using 1 M extractant at an O/A ratio of 1; these conditions resulted in complete Y and Eu, 95 % Ce and 99 % Tb extraction with Ca and Al coextraction below 7 %. A better quality mixed REE product can be produced by operating at lower pH and extractant concentration conditions, but this would require a larger number of extraction stages. Keywords: Cerium, fluorescent lamps, phosphors, rare earth elements, solvent extraction, terbium

Jan 1, 2020

1. Mintek reports The folowing reports are available from Mintek, Private Bag X3015, Randburg, 2125 South Africa. They are available at R25 (plus R3,25 GST) per copy to South African addressees, and US$25 per copy (including airmail postage) to addressees elsewhere. Report M91D A mineralogical investigation of samples from the Renosterkop tin prospect near Upington, by M.J. Southwood. First issued Jul. 1983, reissued May 1989. 16 pp. Report M256D The upgrading of Mamatwan manganese ores heavy-medium separation, by P. W. Overbeek. First issued Apr. 1986, reissued May 1989. Report M299D A mineralogical investigation of samples from the Eenzaamheid cobalt-molybdenum deposit, by C.D. de Nooy. First issued Jan. 1987; reissued May 1989. Report M301D The evaluation of manganese metal powder by automatic image analysis, by E.J. Oosthuyzen. First issued Feb. 1987, reissued May 1989. 13 pp. Report M311D Mineralogical and beneficiation studies of ore from Lutzputz, by R.N. Guest and C.T. Logan. First issued Mar. 1987, reissued May 1989. 13 pp. Report M314D The beneficiation of a sample of magnesium ca/crete, by L. Jonker. First issued Apr. 1987, reissued May 1989. 13pp. Report M369 The determination, by flow-injection analysis, of thiocyanate, by E.A. Jones and M-J. Hennings. Jun. 1989. 7pp. Report M389 A spectrophotometric method for the determination of zinc by flow-injection analysis, by D.E. Barnes and RA. Jones. Jul. 1989. 15 pp.2. Recent publications Pumps-principles and practice. Available from K. Myles & Associates CC, P .0. Box 2212, Northclif 2115. :200pp. R99 including GST. Standard handbook of hazardous waste treatment and disposal, edited by H.M. Freeman. Bergano Book Co., P .0. Box 190, Fairfield, CT 06430, USA. 1120 pp. US$130.Quality control handbook, by J. Juran and F. Gryna Jr. Bergano Book Co. (address as above). 4th 00. 1536pp. US$125.Refractories in the manufacture and transport of pig iron. Verlag Schmid GMBH, P.O. Box 6609, 7800 Freiburg, West Germany. DM 100. The user-computer interface in process control, byW.E. Gilmore, D.I. Gertman, and H.S. Blackman. London, Harcourt Brace Jovanovich Ltd, 1989. " 312pp. $29.Aluminum alloys-contemporary research and applications, edited by A.K. Vasudevan and R.D. Doherty. London, Harcourt Brace Jovanovich Ltd, 1989. " 676 pp. " £90.3. TMS publications issued recently The folowing publications are available from The Minerals, Metals & Materials Society, 420 Commonwealth Drive, Warendale, PA 15086, USA (Telephone: (412) 776-9000, Telex: 9103809397, Fax: 4127763770). Advances in magnesium alloys and composites, by H. Paris and W.H. Hunt (eds.). 145 pp. $65. Arsenic metallurgy-fundamentals and applications, by R. Reddy (ed.). 515 pp. $104. Casting of near net shape products, by Y. Sahai (ed.). 7oopp. $155.Continuous casting of non-ferous metals and alloys, by H.D. Merchant, D.E. Tyler, and E.H. Chia (eds.). 360 pp. $90.Dislocations and interfaces in semiconductors, by K. Rajan, D. Ast, and J. Narayan (eds.). 210pp. $75.

Jan 1, 1989

By M. M. Makhofane

Anhydrous zirconium tetrafluoride can be used as a precursor for the manufacturing of nuclear-grade zirconium metal. This can be done by fluorinating plasma-dissociated zircon with ammonium bifluoride in a batch reactor. This paper describes the batch process. It was proved that anhydrous zirconium tetrafluoride can be manufactured by this route as confirmed by X-ray diffraction. The process shows potential for scaling up to the kilogram scale and possibly the tonnage scale.

Jan 1, 2012

By E. L. J. Kleynhans, J. I. J. Fick, J. P. Beukes, P. G. van Zyl

"Ferrochrome (FeCr) is vital for the production of stainless and high-alloy ferritic steels, since it is the only source of new Cr units. FeCr production is an energy-intensive process. The pelletized chromite prereduction process is most likely the FeCr production process with the lowest specific electricity consumption (SEC), i.e. MWh/t, currently in operation. However, due to increases in costs, efficiency, and environmental pressures, FeCr producers are attempting to lower their overall energy consumption even further. Recently, it was proven that pre-oxidation of chromite ore prior to pelletization and prereduction significantly decreases both the SEC and lumpy carbonaceous reductants required for smelting. This paper presents the first attempt at conceptualizing the technoeconomic feasibility of integrating chromite pre-oxidation into the prereduction process. Financial modelling yielded a net present value (NPV) at a 10% discount rate of approximately R900 million and an internal rate of return (IRR) of approximatelyy 30.5% after tax, suggesting that the implementation of pre-oxidation prior to pellet prereduction may be financially viable. Sensitivity analysis indicated that the parameter with the greatest influence on project NPV and IRR is the level of prereduction. This indicates that the relationship between maintaining the optimum pre-oxidation temperature and the degree of prereduction is critical for maximium process efficiency. IntroductionStainless steel is a crucial alloy in modern society. Virgin chromium (Cr) units used in the manufacturing of stainless steel are obtained from ferrochrome (FeCr) – a relatively crude alloy consisting predominantly of Cr and iron (Fe) (Murthy, Tripathy, and Kumar, 2011; Beukes, van Zyl, and Ras, 2012). FeCr is produced mainly by the carbothermic reduction of chromite ore in submerged arc furnaces (SAFs) and direct current arc furnaces (DCFs) (Neizel et al., 2013; Beukes, Dawson, and van Zyl, 2010; Dwarapudi et al., 2013). The energy required to heat, smelt, and reduce the chromite ore to the metallized state is supplied by electricity (Pan, 2013). FeCr production is an energy-intensive process, with a specific electricity consumption (SEC) varying from 2.4 MWh/t to more than 4.0 MWh/t FeCr produced, depending on the process applied (Pan, 2013; Neizel et al., 2013). Daavittila, Honkaniemi, and Jokinen (2004) stated that the typical operational costs of FeCr smelters can be divided into four categories, i.e. chromite ore (30%), carbonaceous reductant (20%), electricity (30%), and other production costs (20%). This makes electricity consumption the joint largest factor that influences operational costs in FeCr production."

Jan 1, 2017