Search Documents

Jan 1, 1960

By Warren C. Bracewell

At your request, am submitting to you several suggestions for the amendment of our safety code which you felt should be kept up to date. These suggestions are the individual opinions of the several members of the Committee who have expressed (heir wishes to me in the form of letters. I am particularly indebted to Mr. Daniel Harrington, Mr. Wm. Littlejohn, Mr. Warren Bracewell, Mr. James Dalrymple and Mr. Hugh McLeod. Would recommend the following amendments Section 1. Wherever practical trolley wires should be securely hung to roof or timbers at a distance of not less than five feet and not more than six and one-half feet above rail and six inches to one side. Spacing of hangers should be from 20 to 25 feet apart. (Adopted.) Section 2. 500 volts D. C. should not be allowed in any installations. Trolley wires should not carry a voltage of more than 250 D. C. nominal voltage. (Referred back.) Pumps, mining machines and other small machinery units where A. C. power is used should not carry a voltage of more than 220. Large units, such as pumps, motor generator sets and hoists, may use a volt- age of 2,200. When power cables to operate same are of armored construction, cables should be securely buried at all crossings, on haulage-ways or where men travel. (Adopted.) Section. 4. Where power lines pass through door frames or stop- pings they should be properly insulated with porcelain compound or rubber tubing. Wherever men get on or off man-trips in vicinity of trolley wires same should be secure1y guarded and should also be protected with a cut- out switch, same to be pulled before men are allowed to get on or off trips. (Adopted.)

Jan 1, 1926

[Addison, Herbert Big Horn Colleries Co., Colo. Bldg., Denver, Colo. Aleshire, N. C c-o Roberts & Schaefer Co., Wrigley Bldg., Chicago, Ill. Alexander, John Dacona, Colo. Allan, David Lafayette, Colo. Allen, John Ludlow, Colo. Allen, Thomas Box 420, Glenwood Springs, Colo. Alley, Gerald C. F. &I. Co., Pueblo, Colo. Allison, ArchieBox 562, Walsenburg, Colo. Allison, D. S 1331 Roberta St., Salt Lake City, Utah Allison, Park Engineer, Standard Coal Co., Standardville, Utah Allonier, Howard R c-o Lunkenheimer Co., Cincinnati, Ohio Ambler, J. B c-o Ambler & Riter, Kearns Bldg., Salt Lake City, Utah Anderson, A. E 403 Ideal Bldg., Denver, Colo. Andrews, Sam 503 Pike Ave., Canon City, Colo.. Angster, Joe Walsen, Colo. Angus, William B. W. Snodgrass, 1575 Lafayette St., Denver, Colo. Apperson, A. B Tramway Bldg., Denver, Colo. Armstrong, C. D Apperson Vallery Co., Tramway Bldg., Denver, Colo. Arnoldi,, Victor Ideal, Colo. Autrey, J. S Perrenaud Apts., Denver, Colo. Bachman, W. H 1601 Alcott St., Denver, Colo. Bailey, R. E Utah Power & Lt. Co., Kearns Bldg., Salt Lake City, Utah Baird, Elmer A Equitable Bldg., Denver, Colo. Bartlett, G. F 311 Ernest & Cranmer Bldg., Denver, Colo. Baxter, John M 3748 Lafayette St., Denver, Colo. Becker, J. A Box 682, Rock Springs, Wyo. Beebe, John. D 1414 Court Place, Denver, Colo. Bennett, F. C Colorado Fuel & Iron Co., Berwind, Colo. Benson, Geo Cumberland, Wyo. Betcher, B. L Standardville, Utah Beuchat, Charles Pryor, Colo. Bevan,John 1625 North Corona St., Colorado Springs, Colo. Bisch, James L Van Houten, N., M. Boissier, A. H. C Boston Bldg., Denver, Colo. Bottomley, Edward Kleenburn, Wyo. Bowen, James V Union Coal & Coke Co., Colorado Bldg., Denver, Colo. Bowie, Alex R Bowie, Colo. Bowie, John S Bowie, Colo. Bowie, Wallace D Bowie, Colo. Bowns, W. J Castle Gate, Utah Boyer, F. E 631Jackson St., Denver, Colo. Boyle, Chas Sweetwater, Wyo. Brandenburger, L 59 W. Broadway, Salt Lake City, Utah Brennan, W. D Dawson, N. M. Brewster, Burt B Walker Bank Bldg., Salt Lake City, Utah Brockman, A. L Sugarite, N. M. Brooks, Ed 513 Second St., No. 1 Hill, Rock Springs, Wyo. Brown, Geo. A Cumberland, Wyo. Brown, L. E :.1212 Walker Bldg., Salt Lake City, Utah Brown, Mark Y 629 East Main St., Trinidad, Colo. Bubb, H. H Cokedale, Colo. . Bullock, W. H 1052 Gas & Electric Bldg., Denver, Colo. Bunning, P. C Rock Springs, Wyo. Burnite, Thomas B 523 Boston Bldg., Denver, Colo. Butler, T. H Hanna, Wyo.]

Jan 1, 1924

[Mr. Houston T. Aars Carter Mining Co PO8 3007 Gillette, WY 82716 Mr. Jay Abbott Union Supply Co 7458 S Jackson St Littleton. CO 80122 Mr. Ronald H. Achziger Midwest Rbr & Sply Co 6404 E 39th Ave Denver, CO 80207 Mr. Randy Acre Dorchester Coal Co 9350 E Arapahoe Rd Englewood, CO 80112]

Jan 1, 1983

The 75th Regular Meeting of The Rocky Mountain Coal Mining Institute convened at The Mark Conference Center, Lionshead Village, Vail, Colorado, and was in session at 10:00 a.m. Past President, Shirl C. McArthur, President and General Manager, American Coal Company, Huntington, Utah, called the meeting to order. The membership was asked to stand and pledge allegiance to the flag. He introduced President Robert E. Murray, President, Western Division and Subsidiary Companies, The North American Coal Corporation, Bismarck, North Dakota. A biographical sketch follows: Since 1974, Mr. Murray has been President of the Western Division of The North American Coal Corporation, as well as President of The Falkirk Mining Company and The Coteau Properties Company, wholly-owned subsidiaries of North American. Previously, Mr. Murray, who has been associated with North American for twenty- three years, served as Vice President-Operations, Vice President - Eastern Division, and Assistant to the President of the Company. In these positions, he was responsible for North American operations in Pennsylvania, North Dakota and Utah.

Jan 1, 1979

Jan 1, 1938

Jan 1, 1930

Jan 1, 1970

Jan 1, 1951

Jan 1, 1932

CHAIRMAN I. N. BAYLESS: Will you come to order, gentlemen? They told me that you had a very interesting meeting yesterday and a good time last night. Our program is rather long this morning, and I am not going to take up any of your time, as we got started a little late. I will ask Mr. Marchant to make a few announcements. (Announcements.) SECRETARY MARCHANT: I just noticed in this morning's paper a rather serious accident at Hobbs, New Mexico, in which George Kaseman, a former President of the Institute, and a loyal member ever since its organization, was killed. I think that this meeting should go on record and prepare a resolution of condolence, etc., and with your per- mission we will have the Committee on Resolutions do that. I assume that will be all right. CHAIRMAN BAYLESS: Our first paper and discussion this morning will be Education of the Miner, by Thomas Allen, Chief Coal Mine Inspector of Colorado. Mr. Allen.

Jan 1, 1938

By Glen A. Knox

The writer has been asked to set forth for this Institute, the experience of the past eleven months in the mining operation conducted at Sweetwater Mine in which coal has been produced by the use of Link-Belt Conveyors on long faces. The coal in this mine has an average of six feet three inches in thickness, and lies on an average pitch of five degrees. The roof is a sandy shale of medium hardness and has been generally considered as good top in the room and pillar method of mining. When our company became interested in conveyors, the writer visited most all of the mines in the East where conveyors and other mechanical methods of mining were in use and decided that the modified method of w-hat is in use at the Norton-West Virginia mine would be the most feasible for our conditions. We in- stalled three hundred feet of conveyor as an experiment to see whether or not our roof could be handled and taken care of on long faces. This three hundred feet was installed as two separate conveyors, one as a face conveyor-100 feet in length, the other as a heading conveyor that delivered the coal into the mine car on the main entry. This face was worked directly on .the strike and down the pitch. This did not prove to be a success as the caving of the roof carried over to the working face and necessitated propping between the conveyor and the face and it was also necessary to shovel coal on the conveyor up the pitch. After working out this block, 200 feet in length, we installed these two conveyors at a place adjoining this worked out block, but on a half V shape shown on the sketch. This block of coal was sixty feet wide. This method proved to be very successful. We cut a place, moved the conveyor against the face before shooting and carried two rows of cribs between the conveyor and the cave, and caved the roof every second cut. After working out this block we were satisfied that this system was feasible with our mine. We then ordered twelve hundred feet more of the same type as the trial conveyor with the exception of a very few modifications. We then installed this fifteen hundred foot unit on the four faces shown on the sketch, with one hundred feet to each face, two hundred feet on each heading and three hundred feet on the main conveyor that delivered the coal into the pit cars. We also had a head and rear section for each of the four advancing places shown on the sketch. As the sections were taken out of the heading conveyors they were installed on the advancing conveyors, and when the faces approached the main conveyor, the main conveyor was taken out and installed in the next uphill or main conveyor place. The roof caved very well in line of the points and was broken about every twenty feet. It broke in a straight line and did not curve at each V. We encountered no trouble unless we permitted one of the points to get behind. The maximum tonnage possible to be produced on this method was estimated to be seven hundred and twenty-five tons a day, assuming that all places were cut and cleaned up in one shift, and this we did for several consecutive days. While this was a success from a cost standpoint, we felt that we could

Jan 1, 1925

The Wednesday morning session was called to order by President Lewis at 9:00 am, He called on Bob Wilson to conduct the business meeting. In the absence of any of the Auditing Committee, the treasurer's report, which had previously been examined by them was read. He asked for a motion of approval. It was made, granted and approved. The Resolution Committee was called on to make its report. Mr. Shirl McArthur read the following report: (1) "WHEREAS, the Pneumoconiosis or Black Lung provisions of the Federal Coal Mine Health and Safety Act which have been construed and administered largely as a welfare program rather than as just compensation for occupational disease has resulted in enormous expenditures and commitments from the Federal Treasury, WHEREAS, the imposition of the full cost of future welfare oriented black lung awards on coal operators without regard to workmen's compensation standards and without due process in granting benefits is grossly unfair and discriminatory to the coal operator and places an undue burden on the present cost of coal,

Jan 1, 1973

By Glen A. Zumwalt

Coal's Dynamic Legacy The first session presented by Mr. Zumwalt emphasized Western coal development, the heritage of the industry and its growth in the West. The session began with a brief description of the geologic origin of coal followed by a short history quiz given the audience to stimulate their curiosity and involve them in the presentation. Slides and flip charts were used as visual aids and a demonstration of energy resources and uses was made by playing the famous Skyline jelly bean game. Coal Mining Today Today's coal mining practices were dealt with in the second session as Mr. Zumwalt appeared dressed in the garb of the modem day miner. He then led a discussion of coal production in the Western states, its uses and the different techniques used in extracting coal from both a surface and an underground mine. Current coal transportation and markets were also touched on. Our Exciting Future Recent coal growth in the marketplace and new uses of coal products to the year 2000 were dealt with in the final session. Mr. Zumwalt covered things that currently impede the expanded use of coal and things that can negatively or positively affect the future use of coal. In each of the three sessions, Mr: Zumwalt was ably assisted by Mrs. Janet Gwilliam, his secretary at Utah Fuel Company.

Jan 1, 1984

[ACC, Inc. Bucyrus-Erie Company CINCO (Coal Industry Consultants, Inc.) Coal Magazine Colowyo Coal Company Coors Ceramic Company Crane & Hoist Sales, Inc. Cummins Power. Inc. Cummins Southwest, Inc. Cyprus Coral Company Denver & Rio Grande Western Railroad Company Energy Fuels Corporation FMC Corp.- MHE Division Ford. Bacon & Davis Inc. T.J. Gundlach Machine Company Hemscheidt American Corp. GH Hensley Industries Honnen Equipment Company Jennmar Corporation Soy Technologies, Inc. K&P Sales Engineers, Inc. Kennametal, Inc. Kerr McGee Coal Corp. McLanahan Corporation National Mine Service Company Peabody coal Company Pitrsburg & Midway Coal Mining Co. Pyramid Parts, Div. American Alloy Ramsey Technology. Inc. Roberts & Schaefer Company Santa Fe Pacific Coal Corporation Scandura. Inc. Tamarron Resort TIC (The Industrial Company) Tribol Utah Power & Light Western Energy Company]

Jan 1, 1988

Jan 1, 1951

By Wm. Moorhead

Safety Measures Employed at the Dawson Mines Preventive measures for eliminating and localizing explosions is a subject of special interest to Coal Mining operators at the present time. I shall endeavor in this paper to present the practical methods which have been developed at the mines of the Stag Canon Branch of the Phelps-Dodge Corporation, Dawson, New Mexico. Adobe Dusting Adobe is used for practically all dusting on the main haulage roads. It is obtainable in sufficient quantities adjacent to the mines. Loaded into railroad cars by a clam-shell loading crane, and transferred to the mine pit cars at the nearest available point, it is readily distributed along the motor roads by means of the mine locomotives. Of first consideration for adobe dusting is the preparation of the roadway. It is essential that all loose coal and dust be removed, at least to a depth of three or four inches below the top of the rails. The adobe, in a more or less moist condition is unloaded by hand from the pit cars and stored along the previously prepared roadway, to be later scattered to a depth of several inches over the floor, and over the ribs and roof such as is possible by the use of a shovel. The adobe soon loses its moisture and becomes pulverized. Due to the disturbance caused by passing motor trips, men and animals, the dust is effectively scattered along the ribs and roof of the roads. The velocity of the intake air aids materially in sustaining the suspension of this inert matter. Another scheme for distributing the fine dust in use is to chain the top of a pine tree to the rear of the trips, both empty and loaded. Dragging it along the motor roads stirs up the dust and aided by the intake air it is carried for long distances into the workings. The adobe is continually loosened and raked, all rock, coal, etc., being collected in piles and later loaded out in pit cars. One man is employed for each six thousand feet of entry. Dusting Main Return Air-Courses The air-courses are first thoroughly cleaned. All the loose coal and rock is loaded out, the ribs and roof washed down several times. Every five or six hundred feet, the stoppings between the main and return entries are broken through and small doors installed. Blowers are used to force the fine dust into the return air-courses through these openings. Thus suspended the dust travels a considerable distance before it is deposited on the floor, ribs and roof. The material used is chiefly adobe, sun dried, and screened on the outside. A two ton car load of this dust will cover several hundred feet of airway as very little loss occurs, often depositing from 2 to 6 pounds per running foot of entry. Methods of Insertion Blowers are used to force the dust into the main returns. One unit consists of a small Buffalo blower mounted on a truck with a two H. P. motor. A six-inch pipe is attached to the blower and runs the full length of the truck with a projection over the end. A hopper is built over the pipe and connected. Stove pipe or canvas tubing is led from the pipe through door in stopping. When the blower is started dust is fed into the

Jan 1, 1924

By Richard Woodward

Presentation Outline ?What types of coal analyzers are there? ?What do they measure? ?How do they work? ?How accurate are they? ?Most common applications ?Sorting ?Blending ?Prep plant optimization ?Boiler Control

Jan 1, 2006

Jan 1, 1950

By Thos. A. Stroup

From time to time the question of shearing or vertical cutting of rooms and entries especially as an adjunct to the usual horizontal cuts, has cropped up in the literature of coal mining and in the discussions of mining men. Exact and definite data based an thorough tests have usually been lacking however and the present article is written to supply as far as possible this deficiency. The tests given below were made over a period of 90 days in the summer of 1921 and the object was to investigate the general .economics, if any, that might result from the introduction of vertical cutting as a standard practice into the Clear Creek mines. The machine used was the Oldroyd Universal coal cutter and comparative tests were made against the Goodman Straight- face machine and the 35 B Jeffrey Shortwall. The tests however should be held to apply only to the various methods of cutting and not as a study in the relative merits of the various machines. The first series of tests were made in the 2nd East district of No. 3 mine, where only entries were being driven at the time, the tests therefore cover only entry work. The presumption was that the entry width would be 12 feet but the oxerrun in some cases was marked enough to make the work comparable to rooms. The first test made was to determine the time necessary to shear as well as cut the places, and the results were reduced to the time necessary to cut a ton of coal. The time for shearing in the table includes the time necessary to revolve the cutter bar to the vertical position.

Jan 1, 1924