Search Documents

By W. A. Calhoun

The purpose of this investigation was to develop a procedure for removing excess iron from representative samples of bauxite ore from the Quapaw deposit of American Cyanamid Co., Saline County, Ark., in order to produce a beneficiated ore suitable for use in the alum industry, At the request of the sponsoring company, the samples were reduction-roasted at 800° C. and then magnetically separated. Although some rejection of iron was effected under these conditions, the general results were not satisfactory, A much more successful procedure, from the standpoints of both rejection of iron and recovery of alumina, consisted of a short (l5-minute), low-temperature (400° C.) oxidizing roast, followed by a 2-minute interval in a hydrogen atmosphere, then cooling to room temperature, and, finally, high-intensity magnetic separation to remove the iron.

Jan 1, 1957

By Ann G. Kim

Methane in coal constitutes a serious hazard during mining. Draining the methane from large blocks of coal in advance of mining is an effective method of improving the safety and efficiency of coal mining. Because of the similarity of the two gases, drained methane can be recovered and added to pipeline supplies of natural gas. To effectively apply advance drainage techniques and recover drained gas, a gross estimate of the methane content of coal is necessary. Using data from previous investigations, the virgin reserves of the Pittsburgh coal in the central and southwestern parts of Washington County, Pa., are estimated at over 1.5 billion tons, with a methane content of 50 to 100 fts/ton. The Pittsburgh bed in this area of approximately 265 mi2 contains over 130 billion ft3 of methane.

Jan 1, 1974

By Jay F. Colinet, John A. Organiscak

In This Chapter [Which dust source to address first How much air and water are needed Keeping dust out of the walkway Moving workers upwind Dealing with the stage loader-crusher Gob and wing curtains to aid airflow The shearer-clearer system Modified support movement practices and Dust control for future longwalls ] Controlling longwall dust is not easy. Longwall production levels are high, and there are several different sources of dust to contend with. If dust levels are high, the initial effort should be devoted to finding which source is the cause. Then, efforts to reduce dust can be concentrated where they will have the most impact. To control dust at longwalls, a large amount of ventilation air and spray water must be used. The water must be sprayed correctly so as not to blow dust into the walkway. Techniques to change local airflow patterns can be helpful. The shearer-clearer, as well as gob and wing curtains, are examples of such techniques. DECIDING WHICH DUST SOURCE TO ADDRESS FIRST [If a longwall is out of compliance with dust standards, knowing where the extra dust is coming from helps to get back in compliance quickly.]

Jan 6, 2003

By Kevin Connor

Exports of agricultural products, mostly coffee, continued to account for more than 90% of Burundi's foreign exchange revenue. The country's ban on commercial mining was lifted in 1987. Mining of peat for fuel, limestone for agriculture, and clay for insecticides continued as in previous years. At yearend, Burundi's external debt stood at almost $700 million.2 Amoco Burundi, a subsidiary of the Amoco Petroleum Co., drilled two exploration wells in northern Lake Tanganyika in 1987. No oil was found, but preliminary findings were encouraging enough that further seismic surveys and offshore and onshore drilling exploration were planned in 1988. Any oil or gas finds would have substantial impact on the Burundian economy because a major portion of the country's trade deficit was directly attributable to petroleum and gas imports. The Zaire Government agreed in June to let Amoco Burundi explore Zaire's side of Tanganyika using the same equipment and personnel being used in Burundi.

Jan 1, 1989

By Daniel C. Boteler

Data from 68 entrained-bed carbonization tests were treated statistically by the Bureau of Mines, and several useful relationships were developed among the major variables. Nine coals, ranging in rank from lignite A to high-volatile A bituminous, were carbonized in two entrained-bed carbonization pilot plants. The carbonizing reactors employed were vertically mounted cylinders, internally heated, refractory-lined, and 10 inches ID. The range of carbonization temperatures was from 825° to 1,600° F. Using a regression-analysis computer program, empirical equations were developed by which carbonization temperature, air-to-coal ratio, devolatilization of coal, char yield, and volatile matter content of product char may be predicted.

Jan 1, 1973

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992

By D. Z. Hobbs

Because an economic method for preparing pure boron has not been developed, a program was started by the Bureau of Mines to evaluate existing techniques or to develop new methods for preparing the pure element. This report describes investigations directed toward the development of techniques for the preparation of pure boron by fused-salt electrolysis. Only two of the several fused-salt baths tested were satisfactory for the preparation of boron. These baths contained (1) potassium fluoride, lithium fluoride, potassium fluoborate and boron trioxide; and (2) potassium fluoride, potassium chloride, and boron trioxide. Of these two mixtures, the latter was more satisfactory. Elemental boron of from 90- to 95-percent purity and, in isolated cases, as high as 98-percent purity, was prepared from these two types of fused-salt baths. There appeared to be no distinct differences either in the yields or the purity of boron prepared at current densities ranging from 795 to 1,000 amperes per square foot. Current efficiencies were as high as 85 percent.

Jan 1, 1961

Provide a means to (1) rapidly disconnect a multifunctioning signal channel from a multichannel data collection system, (2) protect electronic devices from damage while causing the minimum amount of data collection disruption, and (3) operate electronic devices under gassy mine conditions. Background Data collection system instrumentation and cables are often located in hazardous areas of underground coal mines. As a result, frequent damage to the instrumentation cables occurs from roof falls, heavy equipment, and the relocation of air, water, and power lines. A similar problem exists in surface areas where cables and instrumentation can be damaged by animals and by vehicle traffic. Without a circuit-breaking feature, the damaged cables could cause instrumentation to be ruined, cause power supply failure, and otherwise disrupt data collection in some situations the lack of a circuit-breaking feature might cause an ignition in a methane atmosphere.

Jan 1, 1990

In December's marketing of 99.5 percent aluminum ingot, domestic producer pricing remained at 53$ per pound, while dealer quoting rose from 47.5¢ to 48.5¢. BORON Domestic production of boron minerals and chemicals reached an all-time high in 1977--1.4 million short tons valued at $236 million. Combined sales of the three California producers topped the 1976 level by 15 percent in quantity and 28 percent in value, a consequence of healthy demand in the glass and insulation industries. Unprecedented demand for boric acid as a flame retardant for cellulosic insulation stimulated producers to utilize fully all available capacity, thereby achieving a record output of 158,000 tons. One company increased output from its existing boric acid facilities and initiated production at another plant that historically had produced only sodium borates. A second company achieved a previously planned 25 percent plant expansion.

Jan 1, 1978

By J. M. Stuve

Calorimetric data for the dissolution of scandium sesquioxide and scandium trichloride in 4.360 molal hydrochloric acid were used to evaluate the standard heat of formation of ScCl3(c). The heat of reaction for Sc(c) + 1.5Cl2(g) = ScCl3(c) at 298.15° K was computed as -225,440 ±340 cal/mole.

Jan 1, 1965

By S. J. Hussey

A jig tailing with gold content ranging from 0.33 to 0.43 oz/ton was leached in weak cyanide solution with extractions of up to 97 pct in 24 hours. By countercurrent batch leaching studies and laboratory pilot plant operation, minus 10- plus 20-mesh and minus 6- plus 16-mesh coconut carbon were loaded to 700 oz/ton of Au. Minor silver in the ore reported in the carbon in amounts of up to 100 oz/ton. Gold adsorption rate data and an equilibrium adsorption curve for minus 10- plus 20-mesh carbon at ambient temperatures were developed and used in the successful application of a cascade design theory. The work was performed as a part of the overall Bureau of Mines research effort to help maintain an adequate domestic supply of metals by making improvements in mineral-processing technology.

Jan 1, 1979

By John P. Gooch

Data for the ternary phase diagram for the system 1,1,2,2-tetrabromoethane/water/2-propanol at 25° C have been measured. Experimental methods used are described, and the complete ternary phase diagram is presented. A simple example is given to review the use of the ternary diagram.

Jan 1, 1972

By J. P. Morris

This paper describes a gas-transport method for measuring vapor pressures of liquid metals. Vapor pressures of iron and nickel were determined at temperatures between 1,540° and 1,620° C. The results can be represented by the following equations: log Pmm (iron) -19,460/T + 9.147, log Pmm (nickel) -2l,030/T + 9.689. The study was undertaken as part of a program to determine thermodynamic activities in liquid iron alloys.

Jan 1, 1957

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 4 Description of Subroutines There are thirteen subroutines in the program: PROGIO HOIST MINER SMOKE STENCH MSMOK

Jan 1, 1976

By G. R. Friggens

A nuclear method for continuously monitoring the coalbed and ash levels and void formation in commercial-scale, fixed-bed, pressurized gas producers is proposed. Measurement of gamma ray transmission through the coalbed is the basis of the method. The coalbed level is monitored by detecting the trans-mission of gamma rays from a 1 to 2 Ci Co-60 source positioned on the outside wall of the vessel. Coal bridging or, alternatively, ash level is monitored by a 10 Ci Co-60 source at the center of the coalbed. Source activities and geometries are calculated for a 12-foot-ID producer designed to operate at 350 psi. Source capsule and detector specifications and operational safety are also discussed.

Jan 1, 1973

By T. O. Llewellyn

Laboratory batch and semicontinuous studies showed the feasibility of using methylene bromide and trichloroethylene in heavy liquid cyclone concentration of a Nevada brucite ore. Cyclone tests of minus 20- plus 200-mesh material at specific gravities of 2.42 and 2.44 recovered 71.6 to 74.9 percent of the MgO at grades of 95.5 and 95.4, respectively. Neither increasing the feed pulp density from 5 to 25 percent solids, nor varying feed pressures from 25 to 60 psig had any apparent effect on the heavy liquid separation.

Jan 1, 1971

By E. D. Gardner

"The Bureau of Mines has studied blasting practices in metal mines of the Southwest. The investigation of blasting drift rounds showed among other results, that cut-holes in ground difficult to break could be chambered to advantage under some conditions.In open--cut mines, chambering nearly all holes before blasting is the common practice. Two or more free faces are generally maintained in this type of work, and the amount of explosive necessary to break any bench or bank can usually be estimated from the yardage to be moved. However, in blasting drift or tunnel rounds only one free face is available before the cut-holes are shot, and the quantity of explosive required is generally ascertained best by trial.In addition to being the most difficult to break, the cut-holes are the most important of a drift round. When the cut-holes ""break bottom"" less work is required of the other holes, and a full break of the round is generally obtained. In ground difficult to blast, extra care and expense are justified to insure that the cut-holes ""break bottom.""At many mines the work is so organized that all blasting is done at the end of the shift, and a decided advantage would have to be gained to make chambering of the cut-holes economical. Also, in many mines blasting during the shift would not be practical. One or two holes could probably be drilled during the time necessary to do the chambering. However, under certain special conditions, such as in small operations or those where ""leasers"" or contractors are working, drill holes could be chambered should there be an advantage in doing so. Moreover, in some mines it might be practical to chamber the cut-holes at the lunch hour. In ordinary rounds the cut-holes are generally drilled by noon. It would not be necessary to tear down the drill or remove tools from the face to do this work of chambering."

Feb 1, 1928

By A. B. Hooker, L. C. IlsLey

The greatest hazard of early mining was from explosions of methane ignited by open lights . With the advent of safety lamps and forced ventilation this hazard was greatly reduced until the application of electricity to modern mining not only multiplied the sources of gas ignition but the accompanying , machines and haulage systems increased the amount of explosive dust , through which a methane explosion is more liable to become a major mine disaster , and thus greatly furthered the need of adequate ventilation to keep down the concentrations of methane . Adequate ventilation is still the best preventive of such explosions . However , even with a well laid out and controlled ventilating system the amount of air passing through entries and rooms is liable to vary within wide limits because of open doors , falls of rock , or other accidental causes . The percentages of methane under normal conditions should therefore be kept so small that they will not be increased to explosive proportions by short interruptions in ventilation . Mine ventilation and methane detection are inseparable safety precautions . The increasing importance of ventilation necessitates more accurato determinations of the methane concentrations throughout the mines . This paper discusses in detail some of the steps in the development of methane detection and specially notes the more accurate detectors now available . One of the earliest means of detecting methane was by a candle . About 1835 , John Buddle , Sr. , a noted mining man of his period , when questioned by a Parliamentary Committee as to the safety of using candles , replied :

Jun 1, 1933

By Judith A. Eisele

The possibility of improving the volatilization of gold through the formation of a metal-gold chloride vapor complex was investigated. Gold-silica mixtures, containing ferrous and nonferrous minerals and salts as additives, were treated in a laboratory tube furnace with a flow of chlorine gas at various temperatures. The addition of pyrite (FeS2) to a charge of gold-silica increased the volatility of the gold from 3, 20, and 62 percent of the total gold to 62, 93, and 100 percent at 200°, 300°, and 400° C, respectively. Chemical analyses of the condensate indicated the volatile species to be FeAuCl6.

Jan 1, 1971

"At the request of the Anthracite Institute, the United States Bureau of Mines during February, March, and April 1935, made a field survey of commercial anthracite shipped from collieries scattered throughout the Anthracite regions. In all, 268 samples were taken at 41 breakers from Carbondale at the northern end of the field to Pottsville at the south. These collieries ship approximately 50 percent of the industry’s total production. The geographical distribution of the breakers sampled was as nearly as practicable in proportion to the tonnage of the companies from each region cooperating in the plan.The following are the weighted average analyses, by sizes, of the samples taken in this survey;"

Jul 1, 1935