Search Documents

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By M. J. Ferrante

High-temperature enthalpy and X-ray powder diffraction studies were con-ducted on aluminum sulfide (Al2S3) as part of the Bureau of Mines effort to provide new data for the advancement of mineral technology consistent with environmental preservation and energy conservation. Relative enthalpies were measured with a copper-block calorimeter from 298.15 to 879 K. Tabulated values are listed for heat capacity, entropy, Gibbs energy functions, and relative enthalpies between 298.15 and 900 K. Enthalpies were also given in the form of an equation and combined with published data to calculate standard enthalpies of formation and Gibbs energies of formation for reactions of crystalline aluminum with crystalline, liquid, and gaseous diatomic sulfur. The hexagonal, rhombohedral, and cubic phases of Al2S3 were identified by X-ray powder diffraction studies, and the indexed powder diffraction patterns of these phases are given. The hexagonal phase was stable to about 852 K and was partially converted to the rhombohedral form at 879 K.

Jan 1, 1981

Provide roof to floor closure rate measurements during underground mining, especially retreat mining of coal pillars, thereby helping the miners predict an imminent roof fall. Approach An electronic device and rugged potentiometric extensometer were developed to provide a means fur measuring total closure and the rate of closure. How It Works An intrinsically safe, battery operated instrument is enclosed in a rugged, hand carried field case. The unit is constructed using low-power, integrated circuits to provide minimal battery drain. Two digital Light Emitting Diode (LED) readouts are used; one displays the rate, the other displays the total closure. The unit will measure one extensometer continuously or two extensometers alternately. Two potentiometric extensometers with a closure measurement range of 6 inches are attached to the readout unit. As the roof to floor closure changes, the potentiometric resistance

Jan 1, 1982

By Fred N. Kissell

Methane flows and pressures were measured in mines in the Pittsburgh, Hartshorne, and Pocahontas No. 3 coalbeds. From the data, the permeability of each of these coalbeds was computed. It was found to depend strongly on the type of coal and on the amount of water in the coalbed, and it was found to increase with time. All of the coalbeds had a high-permeability zone adjacent to the face or rib, and the Pittsburgh bed exhibited directional anisotropy. Surprisingly, little or no overburden effect was observed.

Jan 1, 1972

By W. K. Overbey

Knowledge of fracture systems in oil or gas reservoirs is essential to the efficiency of both primary and secondary production operations. A relationship was established between structural features of the surface and both natural and induced fractures in oil and gas reservoirs, thus providing a method of predicting the direction of rock fracture prior to field development and well completion. Correlations between the surface features and under-ground fractures resulted from analysis of joint strike measurements, bottom-hole impression packer surveys, photographs of hydraulically fractured wells, fracture data from oriented cores, in situ strain measurements from formation outcrops, and lineament analyses from aerial photographs. The mean orientation of surface fractures, lineaments, and stress field directions ranged from N 53° E to N 73° E, compared with an average orientation of N 63° E for the hydraulically induced fractures. Tectonic stress field was shown to influence the direction of hydraulically induced fractures. This report presents the details and application of techniques to obtain the orientation of the principal horizontal compressive stress field component and thus the direction of induced fractures.

Jan 1, 1971

By J. Roger Loebenstein

Demand for arsenic exceeded supply, and major domestic and foreign producers allocated available supplies to customers for the fourth consecutive year. Major demand for arsenic was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-Effective April 1, 1981, taxes were collected from companies producing and importing 42 chemicals and petroleum products designated as hazardous, The revenue was used to begin funding of the 5-year, $1.6 billion "superfund" being established under Public Law 96-510, the Comprehensive Environmental Response, Compensation, and Liability Act, designed to help clean up spills of hazardous substances throughout the United States. As hazardous chemicals, arsenic metal and arsenic trioxide were taxed at the rate of $4.45 and $3.41 per short ton, respectively.

Jan 1, 1982

By Michael J. Brnich

Since 1991, Pittsburgh Research Center (PRC- formerly part of the Bureau of Mines) researchers have recorded extensive interviews with 30 individuals who are experts in the area of mine emergency response. These individuals, who have an average of 35 years of mining experience and 29 years of mine emergency response experience, related stories and observations from events that they experienced during their combined 850 plus years in mine emergency response. The purpose of this effort was to gather information that could be passed onto both today?s and tomorrow?s mine emergency responders to train and guide them in handling future events.

Jan 1, 1997

By E. D. Regad, W. E. Wallace, V. Vallythan, V. Castranova, P. Hathaway, F. H. Y. Green, M. J. Keane

"Abstract—Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modelled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiological saline. Lecithin adsorbs to the dusts upon incubation at 3TC and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defence system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modelled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica haemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin haemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate that most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in the same time; that which is. results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.INTRODUCTIONERYTHROCYTE HAEMOLYSIS and pulmonary macrophage enzyme release assays show quantitatively comparable high cytotoxicities for both silica quartz and kaolin respirable sized dusts (BROWN, et al., 1980; DANIEL and LE BOUFFANT, 1980.) This contrasts with the strong potential for respirable quartz dust to induce pulmonary fibrosis and the much more limited potential of kaolin dust to do the same (MORGAN and SEATON, 1975).In an attempt to understand this anomalous situation, assays were performed on quartz and kaolin dusts incubated with dipalmitoyl lecithin emulsified in physiological saline, to simulate the initial contact of a respired dust with the pulmonary alveolar hypophase. The ability of kaolin dust to adsorb dipalmitoyl lecithin from physiological saline has been quantified (WALLACE, et al., 1975). Such lecithin treatment suppresses the cytotoxicity of both silica and kaolin to background levels (WALLACE, et a1.,1984).Surfactant coated detoxified dusts should then be phagocytised by pulmonary macrophages, incorporated into a macrophage secondary lysosome and exposed to hydrolytic lysosomal enzymes. Among these is phospholipase A2, which hydrolyses diacyl lecithin to lysolecithin. This was modelled by incubating lecithin treated dusts with phospholipase A2 in vitro to determine if the enzyme can digest the dust-adsorbed lecithin, and if the retoxification differs between the two dusts in a manner which might distinguish their pathogenicity."

Jan 1, 1988

By Ann G. Kim

The Bureau of Mines investigated factors that influence the formation of methane and other hydrocarbon gases in coal, which is an integral part of the coalification process. Coalification begins with a biogenetic stage in which plant debris decomposes and peat is formed; methane and CO2 are the predominant gases produced during this stage. During the diagenetic stage of coalification hydrogen and the hydrocarbon gases methane, ethane, ethylene, propane, propylene, butene, iso-and normal butane, and pentane are formed by dissociation of the organic material. Methane may also be produced by a secondary reaction of hydrogen with unsaturates or by the reduction of CO2. The gas contained in coalbeds is a mixture of methane, C2 through C5 alkanes, CO2, O2, N2, H2, and He; its heating value is equivalent to that of natural gas. The gas content of coal depends on many variables, but an empirical relationship between adsorptive capacity, rank, and depth has been observed.

Jan 1, 1978

Improve the health and safety of underground mine workers by finding ways of keeping them away from unsupported areas of the mine. Background Roof falls have been the leading cause of fatal accidents in the underground coal mining industry. During 1985-89, 92 coal miners were killed by falls of roof and rib, with more than 4,000 miners injured. According to accident investigation reports from the Mine Safety and Health Administration, 47% of the victims of these fatal roof fall accidents were in the area of unsupported roof al the time they were killed. There is an urgent need to find out why miners go under unsupported roof and to devise strategies for preventing this unsafe behavior. Approach To discover what can be done to prevent miners from going under unsupported roof, confidential interviews were conducted with 297 miners who work in the face crews of 6 different coal mines. The interview topics included company policies and actions regarding going under unsupported roof, how foremen react to people who go under unsupported roof, circumstances likely to cause some people to go under unsupported roof and how to prevent these situations, and observations concerning those who go under unsupported root.

Jan 1, 1991

By Rollien R. Wells

A REPORT of technological advancements restricted to a specific 12-month period is impractical. Inherent in the nature and development of technology is the element of time; rarely can a new process or product be attributed to a particular year. An overall picture of general trends and pattern changes, however, is indicative of technological growth. This paper presents selected observations and discussions of current metallurgical research and practices in an attempt to develop&apos; such a picture. Of the estimated $16.5 billion spent for research and development in the United States in 1962, at least 80 percent was earmarked for the aircraft, electronics, chemical, and machinery industries. Much of the effort was of the end-use variety and was oriented closely to the national defense and aerospace programs. Only a small fraction of the total research money was directed to studies of the utilization and improvement of metals. Even if the investigations in allied fields such as solid state physics are included, the total research expenditure for metal and mineral materials barely reached $500 million. An additional $200 million was spent by industry and government for development of minerals recovery and processing methods.

Jan 1, 1963

By Richard L. Unger

Equipment is the primary cause of injury in 11% of all mining accidents and a secondary cause in another 10%. Purchasers should select new equipment carefully to ensure that the machine incorporates good ergonomic design criteria that maximize the safety of their mine workers. One potential problem area is the workstation-the control center of the machine. Safety problems often occur when the workstation provides insufficient clearance or visibility to the operator or has controls that are difficult to reach. This is especially true for underground mines, where confined space is an issue. In reclined or stooped postures, operators will have less strength and agility and often experience reduced visibility. We have conducted and published much research in Human Factors design of mining machine workstations. This information is currently being compiled into a series of Human Factors design recommendation reports. The reposts dl cover many topics, including workstation layout, control design, seating, and visibility. Each topic has a list of basic or first principles of design. Understanding these principles is the key to designing or purchasing a workstation that is both safe and efficient. Following is a sampling of these main topics and first principles.

Aug 1, 1996

By B. W. Madsen

Bureau of Mines research to recover arsenic from mining industry waste material and process streams is reported. Batch and column approaches were investigated for adsorbing arsenic from acid leach solutions and ion-exchange eluate solutions with hydrated titanium dioxide granules. A method for producing hydrated titanium dioxide granules was devised to provide material suitable for use in a packed adsorption tower. Selective adsorption of arsenic from acidic leach solutions was achieved. The loading capacity of arsenic on the granules was 14 wt-pct when synthetic solutions were used, but lower when actual leach solutions were used. Other elements in the leach solution were Zn, Cd, and In. The granules were used in an attempt to lower the arsenic content in a solution containing 0.95 g/l W and 0.027 g/l As from a process devised by the Bureau of Mines to treat Searles Lake brine. The arsenic content was lowered to less than 0.001 g/l, but unacceptable amounts of tungsten also were adsorbed by the granules. Adsorbed tungsten was partially stripped with pH 11.5 NaOH, and both tungsten and arsenic were completely stripped with 5M NaOH solution. Repeated loading and stripping of the granules had no effect on the loading capacity for arsenic.

Jan 1, 1983

To develop a magnetic levitation transport system that can reduce the cost and improve safety in transporting coal from the face of underground coal mines to the surface. Background Many conventional mining operations use conveyor belts to transport coal from an underground face to the surface of the mine. The Mag-Lev Transport System design replaces conveyor belts with magnetically levitated coal haulage containers moving through a dedicated pipe¬line. Cost estimates, based on current design data, show the Mag-Lev Transport System would have operating and capital costs that are less than or equal to those of an equivalent-capacity conveyor belt system. The safety hazards associated with conveyor belt systems include exposure to moving parts and pinch points, potential fire hazards due to mechanical friction, and the exposure of miners to respirable dust. These hazards would be eliminated or significantly reduced by this novel technology. Approach The Mag-Lev Transport System uses magnetic levitation technology that allows noncontact, frictionless conveyance of a levitated body within a dedicated transit corridor. The mag-lev technology utilizes two types of permanent magnets coupled with an electronic position control system to achieve noncontact levitation. Levitation is provided by neodymium-iron boron (NdFeB) magnets mounted in the base of the haulage containers and inexpensive ceramic-5 magnets located in the bed of the transit corridor. An electronic position control system is used to overcome the inherent instability of the repelling permanent magnets. Proximity sensors, a signal processing circuit, electromagnetic actuators, and fixed ferrous side rails are the major components of the positioning system.

Jan 1, 1994

By C. J. Chindgren

The Bureau of Mines investigated the technical problems involved in recovering commercial-grade vanadium products from alkaline solutions of low vanadium content. Conditions were defined for precipitating calcium vanadates from sodium vanadate solutions with calcium chloride and calcium hydroxide and for dissolving the precipitates with acid, sodium carbonate, and sodium bicarbonate to obtain vanadium-enriched solutions from which either red cake or ammonium metavanadate was recovered. Calcium vanadates with CaO:V205 mole ratios of 2, 3, and 4 were produced with recoveries of 93 to 100 percent. Optimum recovery of the low-lime variety of calcium vanadate was obtained by employing excess calcium chloride and adjusting the pH to a range of 8.0 to 8.5. High vanadium extractions were obtained in concentrated solutions by dissolving the calcium vanadate precipitates with any of the reagents tested. The resulting extracts contained 25 to 125 grams V205 per liter. Conventional procedures used to precipitate either red cake or ammonium metavanadate from the enriched solutions gave excellent vanadium recoveries.

Jan 1, 1967

By D. E. Wolfson

The Bureau of Mines carbonized 21 coal samples from Fayette, Greene, and Washington Counties, Pa., at 900° C, using the Bureau of Mines-American Gas Association (BM-AGA) method, and determined yields of products and physical properties of the coke. These samples represented high-volatile A Pittsburgh, Sewickley, Waynesburg, and Upper Freeport and medium-volatile Upper Freeport and Lower Kittanning coals. About 20 percent of all coals presently carbonized in commercial coke ovens in the United States are mined in Greene and Washington Counties, principally from the Pittsburgh seam. Sulfur content of the Pittsburgh coals in these counties is moderately high (1.0 to 3.2 percent) but, because of extremely large reserves, accessibility to eastern United States markets and excellent blending characteristics to yield strong coke, these counties will continue to be an important source of metallurgical coals in the future. Most coals from the other seams contained more than 2 percent sulfur, which would limit their use as metallurgical coals.

Jan 1, 1968

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Its estimated recoverable reserves in Fayette County are between 670 and 800 million tons. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in determining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ton of coal.

Jan 1, 1977

By Vijia K. Karra, John J. Sammarco, Robert Paddock, Edward F. Fries

Workers in hazardous environments such as mining are constantly exposed to the health and safety hazards of dynamic and unpredictable conditions. One approach to enable them to manage these hazards is to provide them with situational awareness: real-time data (environ-mental, physiological, and physical location data) obtained from wireless, wearable, smart sensor technologies deployed at the work area. The scope of this approach is limited to managing the hazards of the immediate work area for prevention purposes; it does not include technologies needed after a disaster. Three critical technologies emerge and converge to support this technical approach: smart-wearable sensors, wireless sensor networks, and low-power embedded computing. The major focus of this report is on smart sensors and wireless sensor networks. Wireless networks form the infrastructure to support the realization of situational awareness; therefore, there is a significant focus on wireless networks. Lastly, the “Future Research” section pulls together the three critical technologies by proposing applications that are relevant to mining. The applications are injured miner (person-down) detection; a wireless, wearable remote viewer; and an ultrawide band smart environment that enables localization and tracking of humans and resources. The smart environment could provide location data, physiological data, and communications (video, photos, graphical images, audio, and text messages).

Jan 4, 2007

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today&apos;s coal preparation industry.

Jan 1, 1977

By John C. Holtz

The Bureau of Mines studied air contamination caused by diesel exhaust in a 10,000-ft ventilated tunnel. Sequential air samples were taken at the ends and middle of the tunnel during an operating cycle. Observed and calculated results for carbon dioxide, carbon monoxide, and nitrogen oxides were essentially in agreement. Nitrogen dioxide was present only in trace amounts. It was found that contamination was related to the volume of ventilating air, the number of haulage trips, train speed, and engine load.

Jan 1, 1968