Search Documents

By Thomas J. Fisher, Christopher C. Jobes, Edward F. Fries

This report (Software Safety 2.2) is the third in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended or use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and non networked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety .• 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the Safety File is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be don and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treaty of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 9, 2001

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a long-wall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1986

By George R. Schottler

The Bureau of Mines investigated the distribution of uranium and various methods of ore sampling in a uranium deposit typical of those in the Morrison Formation sandstone of the Ambrosia Lake area, Grants mining district, north-western New Mexico. Chemical and radiometric assays of diamond-drill core samples are compared in detail by statistical techniques, and the assay data are correlated with the stratigraphy of the deposit. Conclusions applicable to ore-reserve estimation in geologically similar uranium deposits are drawn.

Jan 1, 1971

By Arthur M. Hartstein

The Bureau of Mines through contract with Ultrasystems, Inc., obtained gram per gram data of products formed on thermal oxidative degradation of selected compositions, both under dynamic and static conditions. Four broad classes of materials were studied! Polyvinyl chloride compositions, neoprene compositions, rigid urethane foams, and variously treated woods. Whenever possible, comparisons between pure components and composites were attempted. Thermogravimetric and differential thermal analyses were performed to gain understanding of the processes occurring and to explore the feasibility of using these analyses as a method of material identification. The toxic products detected and quantitated included HC1, H2S, CO, S02, CS2,COS, HCOOH, CH3COOH, formaldehyde, acrolein, C 6H6, chloroprene, chloroethanol, benzyl chloride, aniline, and furfural.

Jan 1, 1974

By Elizabeth A. Johnson

The effect of slag composition on lead losses to slags and on the behavior of associated accessory elements in lead blast furnace smelting has been studied by the Bureau of Mines. Equilibrations of 30 g of lead and synthetic slag doped with Cu, In, TI, and Sb at 1,200° C in CO-C02 atmospheres revealed the importance of the FeO:Si02 ratio and the basicity ratio, (CaO+MgO):SiO2, of the slag. Lead losses to slags increased with an increasing FeO:Si02 ratio and decreased with an in-creasing basicity ratio. Copper and indium distribution coefficients, [Lx =] increased from 15 at the lower basicity ratios to near 60 at higher basicity ratios. LTI values increased from 20 to 150 as slag basicity increased. Lcu, Lin, and LTI were relatively in-dependent of the FeO:Si02 ratio, but increased with greater amounts of accessory elements in the system. Antimony distribution alone was shown to be strongly affected by FeO:Si02 ratio, although data were scattered. LSb values ranged from 20 to 800 and decreased sharply with increasing FeO:Si02 ratios. The basicity ratio and the level of accessory element load did not have any noticeable effect on LSb.

Jan 1, 1983

By J. J. Forbes

The rapid increase in the quantity of coal being mined by stripping methods is one reason for the increased interest evinced by safety and other agencies in the hazards that are inherent in this Method of mining. The coal-mining laws of some States contain general provisions governing the mining of coal by open-cut methods, but none contains a complete list of specific safety regulations or laws for-the safe operation of such mines. The cool-mining laws of one State empower the head of the coal-mining inspection organization to proscribe regulations for coal-stripping operations and gave him the authority and power to enforce the rules and regulations promulgated by him.

Jan 1, 1944

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a mini-computer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns an echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display discs, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 10, 1980

By S. H. Ash

"INTRODUCTION Mine fires have occurred since underground mining of minerals began, and they are still occurring. The technical literature is replete with papers relating to mine fires.Means and methods for controlling and extinguishing mine fires and preventing explosions and other accidents require the collection and analyses of samples of the atmospheres surrounding the fire. Such atmos¬pheres are complex mixtures of gases (1, 3, 4, 15, 21, 23).3/SUMMARYExperiences at mine fires (1, 3, 4, 15, 21, 23) have proved conclusively that mine-air analyses furnish the only means of judging what is going on in a mine fire area. Mine-air analyses give evidence of conditions that require immediate protection, govern the order and control the manner in which a fire is fought, show the necessity of bulkheads and establish the places to construct them, indicate whether or not a fire is being controlled or is being extinguished, and govern procedure in sealing and unsealing mine fires.It is commonly believed that danger to life and property from mine-fire atmospheres is greatest in coal mines; this is true only to the degree that the explosion hazard is greater in coal mines than in noncoal mines because of the presence of combustible gases. The problem of gas poisoning is greater in noncoal mines because of the more frequent occurrence of poisonous and innocuous gases, oftentimes the lack of controlled ventilation, and usually greater difficulties in sealing mine-fire areas. Sulfide minerals present a serious hazard in many metal-mine fires when sulfur dioxide is formed. The country rock or ore body itself may contain or be limestone, which may be calcined. Emanations of carbon dioxide are found."

Dec 1, 1950

By D. R. Tesarik

An instrumentation and numeric modeling study was conducted by the Bureau of Mines at the Magmont Mine in Bixby, MO. An isolated section of this room-and-pillar mine was monitored with borehole and closure extensometers during a pillar recovery program to determine stress redistribution. In situ stress measurements were taken in the rib before pillar extraction began. Sample cores from the boreholes were taken for analysis of the properties of the host rock in the laboratory. The extensometers recorded no measurable displacements during most of the operation. Two-dimensional, finite-element; three-dimensional, finite-element; and three-dimensional displace-ment discontinuity codes were used to model the area of study. The finite-element models were run with two initial stress conditions, i.e., stress due to gravity only and stress obtained by in situ measurements. Horizontal stresses in the models reduced the calculated factor-of-safety in the mine back by up to a factor of 10, but did not have a significant effect on calculated pillar stability.

Jan 1, 1989

By Paul Sands

Single- and two-stage tests were made with 6-inch, coal-cleaning hydrocyclones to determine the effect of hydrocyclone geometry, operating conditions, and feed composition on performance. Most of the testing was conducted in an open-circuit pilot plant that had a maximum capacity of about 9 tons per hour. The coals used in the investigation had top sizes of 1/4 inch and 28 mesh. Considerable latitude was found in the range of geometry variables that could be used without affecting performance adversely, although a certain minimum ratio of overflow to underflow openings had to be maintained for best operation. Two-stage cleaning proved distinctly better than operation with a single hydrocyclone, because clean coal lost in the refuse product of the primary unit can be partly recovered in the secondary. There is an unusually great difference in the specific gravities at which the individual sizes of the feed are separated in the hydrocyclone. This militates against high efficiency because maximum yield occurs when all sizes are cleaned at the same specific gravity. The size composition of the feed and, more particularly, the size composition of the impurity have a greater influence on the efficiency attainable in the hydrocyclone than in most other types of fine-coal cleaners.

Jan 1, 1968

By E. Chin

The mineral industry of Bangladesh was totally dominated by natural gas production and its downstream uses. A small amount of cement was produced, and clays were used locally for ceramics and construction materials. Nitrogenous fertilizer was produced from natural gas and a modest, scrap-based steel industry produced steel for local consumption. The country has been developing and using its abundant and inexpensive gas reserves as fast as practical. The population, however, was predominantly dependent on agriculture for its livelihood. The industrial sector accounted for 10% of the economy, and most of the industrial output was directly associated with agricultural products jute, tobacco, and textiles. Industrial expansion, even with the availability of gas, was severely constrained because of limited domestic demand, lack of skilled work force and management, poor infrastructure, and a low rate of domestic savings. To put greater emphasis on the industrial sector, the Government established a National Committee for Industrial Development in July. The Committee instituted policy reforms in the areas of trade and investment. One important step was to move from a positive import list to a negative list, thereby permitting imports of items not restricted or banned. The system for recovering and approving new domestic or foreign industrial investments was streamlined to expedite what had become a cumbersome, bureaucratic exercise. To encourage industrial development in areas away from the crowded urban centers, several economic incentives reportedly were adopted. These included a reduced tax rate on imported machinery, exemption of import license fees, a reasonable debt equity rate, and a 9-year income tax exemption period.2 In the trade sector, imports increased 12% in fiscal year (FY) 19843 mainly

Jan 1, 1987

By T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed was investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By C. L. Brown

Coal has been transported by belt conveyors in mines for many years; however, only since the beginning of the general mechanization period have complete transportation system of this type been employed. Aside from my complete belt-conveyor transportation systems, belt conveyors are frequently used in conjunction with other transportation. Many early installations, for the most part, were made without standards as a guide. As a result, some States have outlined certain requirements based more or less on experience following mine fires. Correlation of these regulations should result in more uniformity in connection with standardization of regulations. The National Electrical manufacturers Association has published standards for mining-belt-conveyor installations2/ that should be helpful to the coal-mining industry generally. Bureau of Mines Schedule 2F3/ requires certain controls for permissible-belt- conveyor drives, and similar requirements are listed in Bureau of Mines bulletin 514.4/ Committees of the American Mining Congress have prepared much valuable information concerning operation of belt conveyors, and a subcommittee on fire-resistant belting has been active. 5/

Jan 1, 1956

By Foster Fraas

A method is presented for the linear evaluation of adsorption data using the equations dC = Ae-rv dv and v = [jT] - q, where dC is the phase composition increment, v a calculated parameter, T the absolute temperature, and A, r, h, g, and q the constants. The value of v is calculated from the composition C for both the adsorption surface and the immersion phase. A plot of v for each phase on Cartesian coordinates results in straight line graphs. With temperature variation, a plot of v versus,[ ] also results in straight line graphs. The equations are applicable to electronic and salt equilibria.

Jan 1, 1962

By F. D. Wang

The Bureau of Mines has developed a computer program for evaluating pit slope stability by the finite element stress analysis and limiting equilibrium method. The program includes the finite element method of stress analysis using triangular elements, finite-element model mesh generation, plotting of the model mesh and stress contours, calculation of a factor of safety along a circular or a plane failure surface, and location of a critical circular failure surface. Instructions for preparation of input data, an example problem, and the program listing are presented.

Jan 1, 1972

By R. M. Santmeyers

This paper presents one of a series of digests of foreign mining legislation and curt decisions that is being prepared in advance of a. general report relative to the rights of American citizens to explore for minerals and own and operate mines in various foreign countries. This interpretation of the mining legislation of Madagascar was prepared from the best information (in French) available in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it dill be referred through the courtesy of the Department of State. INTRODUCTION The basic mining law of Madagascar is the decree of 1923, signed at Rambouillet by the President of France on July 19, and published in the Journal Official de Madagascar et Dependances. It has been modified by a number of subsequent laves and regulations, generally of minor importance.

Jan 1, 1933

By Walter T. Ackley

[The geophone has occupied a prominent position as a mine signalling device since its first introduction. The Bureau has carried out tests at different times with a view to improving the early geophones. The following paper describes briefly the adaption of the vacuum-tube audio frequency Amplifier to a new form of geophone. It is not intended to convey the idea that the results described are sufficient to warrant the drawing of definite conclusions as to the practicability of the electrical geophone, but the data and tests liven herein are made public because of their possible use to the industry and as a result of inquiries received as to the feasibility of such adaptions and modifications of the early geophones. Because of the limited time available to the authors, only one geophone with its auxiliary amplifier was constructed. As is well known, two geophones are necessary in order to determine the direction of a sound. Although the principles upon which the electrical geophone operates appear to be fundamentally correct, it is not possible to state whether two such devices 'rill function as efficiently, (as regards determining direction of sound) as the present geophone. In order to operate efficiently as a direction finder, the amplifiers of the electrical geophone must each amplify with exactly the same degree of magnitude. By proper design and adjustment this can probably be accomplished without greatly complicating the design. inasmuch as audio frequency amplification is used, no tuning; is necessary as is the case with tuned radio-frequency circuits. The same filament and plate batteries can be used to operate the amplifiers and by the use of dry cell tubes, requiring shall filament and plate currents, it if believed that a compact, portable and practical instrument can be evolved. Further investigations of the electrical geophone should be conducted to determine the points outlined in this preliminary report.]

Jan 1, 1924

By F. J. Smith, W. A. Gallagher, C. A. Herbert

"INTRODUCTION A fire started about 10 a.m., November 10, 1947, at the Kings mine, Princeton Mining Co., Princeton, Ind., about 1,800 feet inby the main shaft bottom on the main west haulage road at a point estimated to be 2 miles from the faces of the main west entries. No lives were lost, as 27 men escaped from the mine after a series of explosions, which necessitated sealing the mine on the surface. This information circular shows"" how adverse conditions might be overcome, when reopening a sealed mine, by expert planning and close cooperation on the part of various organizations. Conditions found in the mine after it was reopened were comparable to the worst that had been anticipated, yet the mine was recovered with comparatively little difficulty and a minimum of risk. The open workings in the mine covered a vast area, but most of the mine resumed production of coal after being sealed for only 37 days.The information contained herein also points to the desirability of adhering as closely as possible to a predetermined schedule of operations."

Feb 1, 1949

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines to evaluate the effectiveness of 10 additives to inhibit the self-heating of coal. Aqueous additive solutions were applied to a bituminous coal with a high spontaneous combustion potential, and the minimum self-heating temperatures (SHT's) of the dried coal-additive mixtures were determined in the Bureau's adiabatic heating oven. The relative effectiveness of the additives was determined by the observed changes in the minimum SHT's of the mixtures, or by the time required for the sample temperature to reach 150" C, compared with the untreated coal and a coal-water blank. Sodium nitrate, sodium chloride, and calcium carbonate were found to be the most effective inhibitors, followed by ammonium dihydrogen phosphate, calcium chloride, ammonium chloride, sodium acetate, and potassium chloride. Two additives, sodium formate and sodium phosphate, promoted the self-heating process. Differential scanning calorimetry experiments on the coal-additive mixtures showed that reactions occurred between the coal and some of the additives, but these reactions did not influence the self-heating process.

Jan 1, 1988