Search Documents

By Miles B. Royer

The experimental blast furnace has attracted increasing interest during the past decade as a practical means for investigating a broad range of blast-furnace smelting problems. Under experimental-furnace conditions, information can be obtained with less expenditure of time and raw materials and, therefore, at lower cost than comparable information could be obtained under industrial operating conditions. Furthermore, the experimental furnace may be operated beyond the range of smooth operation, even to failure, to delineate the limits of operability. Such deviation from normal operating practice would be economically intolerable in industrial operations where production and operating stability might be disrupted. The Federal Bureau of Mines experimental blast furnace at Bruceton, Pa., near Pittsburgh, has been operated and under development since 1951. However, the usefulness of this experimental data to industrial practice was somewhat nebulous in early experiments, and the correlation of the experimental blast furnace with the industrial blast furnace was not known.

Jan 1, 1961

By S. L. May

Tantalum and columbium can be extracted from several of their ores or concentrates by chlorination procedures. Direct chlorination of high-grade minerals in the presence of carbon at temperatures between 500° and 800° C will extract up to 99 percent of the tantalum and columbium. Metallurgical beneficiation of low-grade source materials by carbothermic reduction produces a ferroalloy that is amenable to chlorination at a temperature of 500° C. Over 90 percent of the tantalum and columbium can be recovered.

Jan 1, 1965

As part of the Bureau of Mines subactivity in secondary resource recovery and to expand the Nation's mineral base, the Tuscaloosa Research Center made characterization and preliminary beneficiation studies of the waste residues from various coal-conversion processes: from pilot plant tests of the Synthane process for coal gasification, the Synthoil process for coal liquefaction, and the solvent-refined coal (SRC) process for sulfur removal from coal. Those coal conversion processes selected for this study were based on the availability of pilot plant samples. Physical, chemical, and mineralogical examinations of the wastes made to determine the mineral content prior to physical beneficiation tests indicated that in addition to significant quantities of carbon, some trace elements offer potential for concentration.

Jan 1, 1980

Provide a means of recovering precious metal values from finely ground tailing materials. Approach Determine the procedures needed for agglomerating the finely ground material for subsequent heap-leach cyanidation of the precious-metal-bearing tailings. Applying Agglomeration/Heap-Leaching to Fine Tailings Agglomeration technology was developed by the Bureau of Mines to provide cost-effective recovery of precious metal values though better heap leaching of clayey or low-grade ores. While many precious metal producers have adopted this technology to reclaim precious metals from crushed ores and wastes, other operations have experienced problems in using the heap leaching technique effectively on piles of fine tailings. In contrast to the coarser ore and waste material, most tailings piles contain more than 50 percent minus 200 mesh materials with no coarse material. Fine particles and clays present in the pile can impede 8 uniform flow of the leaching solution through the heap, thus preventing efficient and cost-effective precious metals recovery.

Jan 1, 1986

By Jack E. Fraley

The Bureau of Mines has successfully developed and tested a machine for spraying sealant onto coal mine roof and ribs. Dry material is transported pneumatically to a water-adding nozzle designed to provide dust-free spraying while being nonplugging and self-cleaning. The machine is self-cleaning, 35 inches in height, and capable of applying l/2-inch-thick coatings at over 1,000 ft2/hr.

Jan 1, 1978

By Robert W. Freedman

The Bureau of Mines investigated methods of analysis of free silica in respirable dust, including both work done at the Bureau of Mines and work done elsewhere. The review covers both coal dust and noncoal dust, taking into account both existing and proposed chemical and spectroscopic procedures.

Jan 1, 1971

By W. V. Kuster

The investigation described in this report is part of a survey by the Federal Bureau of Mines of the titanium resources of the United States. The purpose of this project was to study a typical coastal deposit of beach sands in the Middle Atlantic States, particularly in the area surrounding the Delmarva Peninsula. The field investigation consisted of a reconnaissance survey of the Eastern Shore of Maryland, followed by surface sampling and drilling of the sands on Assateague Island, off the Atlantic coast of Maryland. The study covered the period January-December 1957. Detailed analyses were made of 5-foot sections of eight drill holes along the Maryland section of the island. The heavy-mineral fraction of these samples was separated by sink-float tests, using acetylene bromide as the heavy liquid. The minerals comprising the heavy fraction were examined microscopically, and mineral counts were made on selected samples.

Jan 1, 1959

By H. Polat, Q. Hu, S. Chander

"The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l "", however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent. INTRODUCTIONSeveral methods are used to control dust in mines. These include: ventilation, foam, scrubbers and sprays. This article is concerned with improving the effectiveness of water sprays, which are widely used to remove dust particles during continuous mining, by adding small quantities of surfactants. Water sprays produce small droplets which act as collectors of dust particles suspended in air. Sprays directed at the actual source of dust have the additional property of wetting the coal before the ·particles become airborne (Hamilton, 1974). Wetting agents, also called surfactants, arc known to play an important role in many applications where dust is a problem. However, conflicting reports exist in the literature with regard to the effectiveness of surfactants in water sprays (for a review, see Chander et al., 1988). In spite of the conflicting reports, the use of surfactants for dust control has increased over the years. In a recent study by the Bureau of Mines, a 27'6 reduction in respirable dust levels was observed in a mine test when surfactants were added to sprays (Foley, 1991)."

Mar 1, 1992

By G. St. J. Perrott, N. A. Tolch

"PURPOSE OF TESTSThe propulsive strength4 developed by the Cardox blasting device depends on the thickness of disk, weight of heater element, and weight of carbon dioxide charge. It might be supposed that the maximum weight of carbon dioxide that can be charged into the shell should give the greatest strength. However, according to the ballistic pendulum, the maximum weight of carbon dioxide with certain conditions of heater and disk has less propulsive strength than a smaller charge; in one condition of test a loss of 39 per cent in propulsive strength was noted. It is therefore of interest to study the effect of the variables that determine the strength of Cardox.ACKNOWLEDGMENTGrateful acknowledgment is made to A. B. Coates, associate mechanical engineer who developed the testing method for measuring pressures in the Cardox shell.DESCRIPTION OF DEVICEThe Cardox blasting device as fully described by the bureau in Report of Investiga¬tions 2920 (1929), consists essentially of hollow—steel shell, cylindrical in shape, an electrode, valve assembly, shearing disk, and discharge cap. The shell is prepared for use by inserting a heater element, closing the open end with a shearing disk, and screwing in place the discharge cap. The charge of carbon dioxide enters the shell through the electrode.The heater element is fired by an electric igniter of the match—head type. The heat released by the heater element completely gasifies the carbon dioxide and raises the pressure of the gas until it is enough to shear the disk."

Apr 1, 1931

By T. A. Henrie, E. K. Kleespies

Electrolytic studies were conducted to determine the transfer rates of the alloying constituents from molten titanium anodes to solid titanium cathodes in molten salt systems . The metals , nickel , tin , copper , bismuth , and manganese , were selected on the basis of thermodynamic data and the melting point of the alloy system . The transfer of nickel , tin , and bismuth was very low . The content of these elements in the cathode was in the range of less than 0.01 to 0.001 percent . The copper transfer was 0.6 to 0.8 weight - percent in electrolytes containing titanium chlorides and 0.12 weight - percent in titanium fluoride salt systems . The manganese transferred at rates comparable to that of titanium . Highpurity titanium and titanium- manganese alloys of uniform composition were produced by electrorefining molten titanium alloys in chloride electrolytes . Comparisons are made between the calculated and the actual quantities of metal transfer .

Jan 1, 1964

By John E. Kelley

Laboratory equipment, which simulates abrasive impacts between steel and minerals that might be present during pneumatic transport of coal, was used by the Bureau of Mines to characterize the potential explosion hazard of such collisions in an atmosphere of fine coal dust, air, and methane. A variety of coal mine rock materials, including sandstone, limestone, and pyrite-bearing limestone, were impacted with specimens of pipeline steel. Tests were con-ducted in atmospheres containing zero to 6.4 vol-pct methane mixed with zero to 300 mg/l coal dust. Coal dust in air alone was not ignited by abrasive impacts, but additions of as little as 1 vol-pct methane to the coal dust and air mixture resulted in ignitions. Steel impacting against sandstone caused ignitions in mixtures of coal dust, air, and methane, and the probability for ignitions increased with an increase in methane. No ignitions occurred with impacts of steel on lime-stone or pyrite-bearing limestone, even when large showers of sparks were produced. Studies of the effect of tangential collision velocity showed that no ignitions of coal dust, air, and methane occurred below 900 fpm (4.57 m/sec). Ignitions in coal-air-methane mixtures were found to be caused by a hot friction-induced smear on the impacted rock at the impact site rather than by sparks. High-speed photography was used to verify this observation.

Jan 1, 1976

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

By R. W. Lewis

The Federal Bureau of Mines Boulder City Metallurgy Research Laboratory conducted experiments in order to develop a spectrochemical method for determining the concentrations of impurities In high-purity tungsten. This report presents a procedure, developed by these experiments, for determining 19 impurities in high-purity tungsten. Metal samples were thermally converted to the oxide, mixed with graphite, which was prepared and mixed with an internal-standard element, and excited in a d.c. arc. Sixteen of the impurity elements were determined with one set of conditions, using germanium as an internal standard. Lanthanum was used as an internal standard in the tests for boron and chromium. Molybdenum required the substitution of sodium chloride for the graphite and the use of copper electrodes. Data on the precision of the method are included in this report. The coefficients of variation vary considerably but average about 15 percent. Higher concentrations of impurities than those investigated may be determined with some modifications of the testing procedure, provided attention is given to the possibility of interelement interferences.

Jan 1, 1961

By Paul W. Jeran

Subsidence over a series of longwall panels undermining sloping terrain in southwestern Pennsylvania was monitored to verify the Bureau of Mines subsidence prediction model for the northern Appalachian coal region. Comparison of the field data to model output shows close agreement. Vertical movements over each panel ceased with the mining of the adjacent panel. Horizontal movements were significantly affected by topographic slope. The distribution of horizontal strains over each panel were similar, with a zone of compression occurring over the center of each panel. The zones of compression were flanked by zones of tension toward the rib. The magnitude of the tensions were affected by the slope. The strains developed at the completion of each panel were not significantly altered by the mining of subsequent panels.

Jan 1, 1988

By William H. Lewis

This paper describes the Bureau of Mines efforts in the research and development of a new and innovative mine lighting system which is based on fiber optics technology. The new lighting concept offers significant advantages over conventional systems in the areas of both safety and long- term maintenance costs. An overview of Bureau research into the problems and limitations of present-day mine lighting systems is also presented.

By R. V. Ramani, J. Qin

"During the mining process, the insitu material is broken into different size ranges, from very, large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable. dust is associated with health and safety of the miners: The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper.. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined.The amount of respirable dust airborne is on the average only. 0.016% of the respirable dust generated. On the average, 61% of the total .airborne dust measured is in the respirable size range. The amount of respirable airborne' is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (<0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of 'the airborne propensity of respirable dusts in mine atmospheres.INTRODUCTIONMining is a sequential process of breaking, gathering, loading, and transporting the in-situ .materials.' In underground coal mines, duet in both the non-respirable and respirable size ranges is generated and entrained in every phase of the process. Even though large amounts of dust particles' adhere to run-of-mine coals, part of the dust generated becomes airborne (Cheng and Zukovich, 1973). Studies have shown that bit type affects the amount of dust generated'(Evans and Pomeroy, 1966; Kurth et al., 1975; Roepke et al., 1976; Stecklein et al., 1982; and Khair and 'Reddy, 1986). Deep cutting can reduce airborne dust generation (Black and Schmidt, 1977 arid, Black et 1978). Mechanical properties of. coal seams are also important factors in dust generation. Laboratory studies have shown that Hardgrove Grindability Index (HGI) of the coal has a relationship with the amount of respirable. dust generated (Beafi and Ramani, 1979; Moore and Bise, 1984; and Moore, 1986). However, these relationships have not yet been validated with' data from the mines. The amount of dust airborne depends on a number of factors. Suppression of the airborne propensity of dust by water sprays is'widely practiced and is very effective. Water flow rate; pressure and configuration of water sprays have been identified as major factors affecting dust capture by sprays (Courtney and Cheng, 1977; Courtney et al., 1978; and Kissell et al., 1979). Ventilation is a very important means of controlling the dust level at the coal face (Jayaraman, 1977). According to a National Academy of Sciences study (1980), the mechanism of dust generation and the process by which the generated dust becomes airborne are complex and not yet completely understood coal seams are also important factors in dust generation. Laboratory studies have shown that Hardgrove Grindability Index (HGI) of the coal has a relationship with the amount of respirable dust generated (Beafi and Ramani, 1979; Moore and Bise, 1984; and Moore, 1986). However, these relationships have not yet been validated with data from the mines. The amount of dust airborne depends on a number of factors. Suppression of the airborne propensity of dust by water sprays is widely practiced and is very effective. Water flow rate; pressure and configuration of water sprays have been identified as major factors affecting dust capture by sprays (Courtney and Cheng, 1977; Courtney et al., 1978; and Kissell et al., 1979). Ventilation is a very important means of controlling the dust level at the coal face (Jayaraman, 1977). According to a National Academy of Sciences study (1980), the mechanism"

Jan 1, 1989

By B. Dimitriades

Data on smog-forming reactivities of exhaust aldehydes are scarce. Such data were obtained by irradiating in a smog chamber typical exhaust aldehydes, individually and in exhaustlike mixtures. Observed reactivity manifestations were rate of nitrogen dioxide formation (RNO2) and yields of oxidant, peroxyacetyl nitrate, and formaldehyde. Results showed that exhaust aldehydes vary widely in reactivity. Formaldehyde showed high RNO2 reactivity but low oxidant yield; benzaldehyde, [m]-, and [p]-tolualdehyde were totally unreactive when irradiated individually; [o]-tolualdehyde was reactive. In mixtures, benzaldehyde manifested reactivity in terms of peroxybenzoyl nitrate yield. Exhaust aldehydes as a group are judged to be as reactive as the exhaust olefin group. The importance of the aldehyde contribution to exhaust reactivity and methods for assessing such contribution are discussed.

Jan 1, 1971

By Raymond M. Stateham

Calculations based on data obtained from measurements of smoke from coal-fired powerplants predict that infrared imagers will be useful tools for smoke vision. Infrared imagers operating in the 3-to 5-um spectral region have been evaluated for this purpose. A mine opening 110 meters long was filled with smoke from burning coal, and two men, wearing breathing apparatuses, moved through the smoke to serve as targets. The men were detected and identified at 80 meters.

Jan 1, 1976

By A. W. Khair, M. Ahmad, Gehi. L. D.

"This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.INTRODUCTION Research has reduced the prevalence of Coal Workers Pneumoconiosis from 15 to 5 percent according to NIOSH reports (Breslin 1982). However CWP still have not been eliminated as a hazard to mine workers. To prevent coal workers from having black lung MSHA has established a very strict standard for coal mine operations (2.0 mg/m3 with silica content equal to or less than 0.1 mg/m3,). There are numerous coal operations still experiencing great difficulty with meeting the 2mg/m3 dust standard. Among these are the longwall sections and continuous mining sections. In order to meet the rising demand of energy and coal, the number of longwall operations and continuous mining operations would have to be increased. Thus a long term research commitment is required to develop basic solutions that are more generic and greater benefit to the mining and mineral industry.In continuous-mining operations, the miners are exposed to the dust produced during the fragmentation of the coal from the face plus the dust produced during loading and transferring of the coal. The fragmentation process generates most of the respirable dust. The amount of dust generated during fragmentation depended on the coal properties, cutting parameters and cutting bit configuration. Bit wear changes bit configuration, therefore, it also affects dust generation. Bit wear can be defined as the removal of material from surface as a result of mechanical action. In soft coal mines bit wear may not be a serious problem but in hard coal seams bit wear is very significant. In addition, as the good coal seams are depleted, the operators are mining thin seams and the seams with rock partings. During cutting these seams operators are sometimes forced to cut roof and floor rock or rock partings which result in more rapid wear of bits."

Nov 1, 1995

By Wilbur Duvall

For the past few years the Applied Physics Branch has been investigating, experimentally, the generation and propagation of strain waves in rock. The strain waves are produced by the detonation of a high-velocity explosive placed in a small cavity in the rock. Strain gages mounted in the solid rock surrounding the cavity record the strain pulses propagated away from the source. Numerous strain-wave pulses have been recorded in different rock types for charges of various sizes and at various distances from the charge. Analysis of these records has shown, among other things, that there is associated with the strain wave a characteristic pulse width. This pulse width is dependent on the rock type and the distance from the shot point to the gage, but is apparently independent of the charge size or cavity size. Recent published literature on the generation and propagation of seismic waves indicates that the characteristic frequency of an elastic wave generated by an explosion should be a function of the rock type and the size of the cavity created by the explosion. Also, internal friction in the rock would produce absorption of high-frequency components, which would cause continual change in the shape of the pulse propagated. As the experimental data did not verify the expected change in pulse shape with cavity size, a theoretical investigation of the vibrations associated with a spherical cavity in an elastic medium was undertaken.

Jan 1, 1950