Search Documents

By Richard F. Hewlett

This report describes a comparison of methods for computing grade and tonnage of ore, leach, and waste material for a mined-out portion of the Silver Bell Oxide porphyry copper deposit, and these computed values are compared with the actual tonnage of these classes of material produced during mining operations. Comparisons with production records have been made by using both exploration drill-hole assays and development blast-hole assays. The polygonal method is the most accurate for this deposit, because it more closely represents the lateral mineral distribution in the deposit. This is demonstrated by plots of the total-copper assay distributions of the development blast-hole assays for a specific bench. The investigation also shows that the smaller vertical assay interval (based on a 5-foot vertical churn-drill-hole sample) yields a more accurate estimate of both grade and tonnage than the 40-foot composite assay interval (based on the average of eight 5-foot assay values). This can be attributed to the fact that selective mining within a bench can separate out much of the waste and leach material that is included as ore in the 40-foot composite assay computations.

Jan 1, 1970

By F. N. Kissell

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By William L. Porter

From the first day of new miner training until the day they retire, mine workers will experience changes due to the normal aging process. It is an unfortunate fact of life that many age-related changes result in diminished physical, sensory, or cognitive capabilities. Of course, workers also gain a tremendous wealth of experience, knowledge, and insight as they age, making them a vitally important resource for their company. Effective leveraging of this precious resource requires both an appreciation of the changes that occur with age and an understanding of methods that can be used to reduce the injury risk that may result. The purpose of this training is to provide the information necessary to accomplish these objectives. Aging workers may not necessarily have a higher injury risk overall; however, the effects of a musculoskeletal injury (MSI) on older workers may be more extreme. MSHA data show that not only does the percentage of MSIs increase when workers are over age 30, so does the number of days lost per injury, as shown in the graph below [MSHA 2005]. [ ] Protecting the safety and health of aging workers requires matching the demands of the job to worker capabilities. This means reducing or eliminating risk factors for injuries, such as heavy lifting, awkward postures, static postures, repetitive movements, and/or vibration exposures. In other cases, it may mean improving visibility or streamlining processes. Designing jobs to accommodate the changing capabilities of older workers will not only reduce injury risk for older workers, it will have the added benefit of protecting younger employees as well.

Jan 1, 2008

By R. D. Leitch

"REASONS FOR AND PURPOSE OF WORKIn 1924 the United States Public Health Service was requested to undertake a special study of stream pollution. At that time the proposal that the United States Bureau of Mines take up the study was made by the Public Health Service because in point of training and experience the personnel of the latter was considered not to be as well, suited to this type of investigation as was that of the Bureau of Mines. H. Foster Bain, then Director of this bureau, promised to undertake the work, and, accordingly, field investigations were begun in the spring of 1925. The problems of mine-drainage wastes and of gas-house and coke-oven waste were investigated in the laboratory, and a method of treatment by sodium hydrate and benzol was found to be promising. The idea was obtained by A. C. Fieldner, chief engineer of the Bureau of Mines experiment stations, while in Germany in 1924, where he was shown a practical application of the process, but no information was obtained as to definite chemical or mechanical processes. Because of the then pending American patent application by the German firm, we made no attempt to develop our findings further. Shortly after, a similar method of treatment was developed in the United States, and since that time we have devoted our attention entirely to mine drainage. This paper is a presentation of some general facts and information gathered during the past five years on coal-mine drainage.SCOPE OF WORKAt the time our work was begun there was such a diversity of opinion on the whole subject and apparently so little was accurately known, that it was decided to undertake a basic study from which (1) certain definite information might be evident, and (2) what might be considered side issues of the original investigation would be suggested for subsequent study.A stream in a district thought to be representative of those in low to average sulphur bituminous coal fields and another in a high sulpbur district were selected for study, A fair (weber of factors entered into the tentative selection of these streams, the chief ones being their accessibility and freedom from other industrial or domestic pollution, besides, of course, the presence of mine drainage in these streams."

Apr 1, 1931

By Henry E. Perlee

In a Bureau of Mines study two-dimensional mathematical equations were solved that describe the transient thermal response of a rock dust particle in a cloud of similar particles in a gas flame's preheat zone subject to a radiant field from the approaching flame. The description includes both radiant energy absorbed and emitted by the particle and thermal conduction inside the particle and into the surrounding gas environment moving relative to the particle. Two situations were studied; in one the radiant energy incident on the particle is converted to thermal energy at the particle surface, and in the other the radiant energy is converted to thermal energy uniformly over the volume of the particle. The result of the study showed that for a 10-µm-radius particle, a 200-mg 1-1 loading density, and a flame approach velocity of 30 m sec-1, the particle temperature rise was twice that previously calculated by Singer and Cook based on the model of Essenhigh and Csaba. It was further established that under the conditions examined a rock dust particle temperature never increases more than about 200 K before crossing the flame front.

Jan 1, 1976

By Thomas H. Dubaniewicz

Fiber optic systems are being deployed in locations where explosive gas atmospheres are normally present or are present under fault conditions. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (NIOSH, PRL) conducted a study of laser safety in potentially flammable environments. Researchers conducted experiments to estimate the mean and standard deviation of laser powers needed to ignite 6% methane-air atmospheres using single mode optical fiber tips covered by two types of iron oxide (Fe304 and (FeMn)203) mixed with a ceramic adhesive. The iron oxides, heated by a 1064 nm continuous wave laser, ignited the methane-air mixtures ,at similar powers. The minimum igniting power and maximum non-igniting power (10 tests) were 407 and 350 mW, respectively, using a 62.5 pm fiber. Laser beams guided by 125 and 80 pm diameter cladding single mode fibers produced similar methane-air igniting powers. Ignition was not observed using coal particles at powers that produced ignition with the iron oxides. Threshold ignition delays using the single mode fiber were approxinlately proportional to the inverse square of the igniting power. Ignition delays were significantly longer than the reported activation time for a comnlercial fiber optic power limiter. Comparisons are made with the results of other researchers. Published by Elsevier Ltd.

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

By George D. Drechsler

The purpose of this review is to provide an analysis of the supply and demand for coal in Europe in 1955-56 and estimates of future growth in European requirements as a medium for appraisal of the effects and benefits to the economy of the United States. This review stems from observations and evaluations made in contacts with Government and industry representatives of the principal countries of Europe and is based on detailed data selected from the established flow of unclassified economic and statistical material originating in overseas areas for use and deposit in the Bureau of Mines, Foreign Solid Fuels Section. This material includes current reports and analyses prepared by the United States Foreign Service, official reports of individual countries, foreign industry and trade publications, and the committees of the several European organizations engaged in continuing review and study of problems relating to fuels and energy. The review is presented in four sections: 1. Discussion of the more important factors relating to the present and future fuels and energy position of Western Europe.

Jan 1, 1957

By B. P. Martinez

This report presents the results of a research and development program in recovering waste-rolling oils conducted by the Bethlehem Steel Co., before 1954 at its Sparrows Point plant, Sparrow Point, Md., with the cooperation of the Bureau of Mines, U. S. Department of the Interior, College Park, Md. The objective of the program was twofold: First, to recover oil for reuse in the plant; and second, to stop pollution, by oil, of the stream and harbor areas in the immediate vicinity of the plant. The sequence of the investigations was laboratory and pilot plant studies on sedimentation, simple aeration, and flotation for the separation of oil and water; and construction of a production unit using standard flotation equipment. This work was only preliminary for the Bethlehem Steel Co. and it has continued research on this problem. Recent progress indicates that new, improved processes will soon replace the flotation units described in this report. The first efforts to separate oil and water by simple sedimentation were unsuccessful. To establish the cause of this failure, microscope examinations and measurements were made on cold-reduction rolling mill cooling-water effluents containing oil in suspension. It was discovered that an average oil globule, held in suspension, was only 0.001 inch in diameter and would not coagulate with other globules for normal sedimentation at room temperature. The next step in the sequence of studies was to coagulate the oil suspension by simple aeration with air under slight pressure. The aeration methods studied were effective in removing up to 68 percent of the total oil but were approaching flotation in principle. The final investigation of the series was flotation of the oil in conventional laboratory-size flotation cells. The small-bubble method, without reagents, floated up to 89 percent of the total oil held in suspension and was the process selected for pilot-plant development.

Jan 1, 1959

By David C. Oyler, Paul B. Stubbs

The Bureau of Mines and United States Steel Corp. are conducting a joint project to monitor formation pressures at a large (23-well) coal- bed gas drainage field near Oak Grove, AL. Three monitor holes were drilled in late 1981, and pressure monitoring began in December 1981. The Bureau of Mines direct method was used to obtain gas content data from cores taken in the monitor holes. Comparison of the 1981 gas con- tent data from the monitor holes with initial gas content values obtain- ed from the production wells in 1977 indicates a 50-pct reduction in ad- sorbed gas content inside the pattern and a 29-pct reduction at one point 500 ft outside the pattern. The combination of pressure and gas content data has also allowed an in situ isotherm curve, relating the formation pressure to adsorbed gas content, to be developed for the area of the production wells. From the current rate of pressure decline (1 lbf/inz per month), the observed changes in gas content, and the isotherm curve, it appears that most of the early gas production came from within the pattern, but since 1981 (and possibly earlier) most of the gas produced has been migrating to the wells from outside the pattern area.

Jan 1, 1985

By Lisa Steiner, Robin Burgess-Limerick

In 2004, underground coal mines in the United States reported 3,405 injuries to the U.S. Mine Safety and Health Administration (MSHA). Of these, 17 percent were associated with the use of bolting machines, 8 percent with continuous miners, and 4 percent each with scoop/load-haul-dump (LHD), shuttle cars and personnel transport. Analysis of the injury narratives identified five hazards that required attention. They are rock falling from supported roof inadvertent or incorrect operation of bolting machine controls, handling continuous miner cable, collisions while driving underground vehicles and driving or traveling in underground vehicles on rough roadways. The rate of lost-time injuries has steadily decreased during the past 10 years (from more than 10 per 100 FTE in 1995, to six in 2004). However, underground coal mining remains a hazardous industry. One of the contributors to this elevated injury risk is working with or near underground coal mining equipment. Roof bolting machines and continuous miners have been consistently identified as high risk equipment. They account for approximately 24 percent of all injuries to underground coal miners (Sanders and Shaw, 1989). LHD's, shuttle cars and personnel transports are also associated with injuries in underground coal mines (Burgess-Limerick, 2005). Conventional analyses of injury statistics typically provide tables detailing the breakdown of injuries by body part nature of injury or mechanism of injury. Such analyses are worthwhile and may be helpful in tracking broad trends over time. Further information is available in the narrative text field completed for each injury reported. The detail contained in these narratives varies. However, they generally provide some insight into the causes of the injury, such as the activity being performed at the tune of

By Robert J. Willard

This chapter includes tables for 1982 that were not available in time for publication of the 1982 Minerals Yearbook, but does not include corresponding tables for 1983. The value of raw nonfuel minerals produced in the United States during 1988 was estimated at $21.1 billion, an increase of $1.5 billion over the value for 1982. This is a reversal of last year's downturn in value from that of 1981, which was the only decrease noted since 1971; hence, an overall trend of increasing values has been maintained for 12 years, except for 1982. Although the reversal is a basis for cautious economic optimism, it is tempered by continued problems in the domestic mining industry: inadequate funds for capital investment and competition with other countries that have lower production costs. Output of metal commodities in 1983 increased for 8 out of 21 metals, and metal values, in general, increased for 9 of the metals. Output of nonmetal commodities was mixed, with 24 nonmetals showing increases, 20 showing decreases, and 2 unchanged. Nonmetal values were also mixed in 1982: 25 showed increases, 20 declined, and 1 was unchanged. Improvements in the international metals market have not been forthcoming because of the continued depressed prices for major metals. Governments in foreign producing countries have been concerned with maintaining employment and continuing foreign exchange flows through mineral exports. Consequently, the excess of supply in the face of shrinking demand brought downward pressure on metal prices in general, except for the precious metals. On the domestic front, this situation means U.S. mining companies must become even more cost efficient. The major trend in the mining industry in 1983 was to cut costs further, reduce or stabilize total production, reduce outlays for major capital equipment, modify existing systems and equipment, and streamline operations. Most of the accomplishments reported herein reflect this trend.

Jan 1, 1984

By Kenneth L. Rubow, Virgil A. Marple, Bruce K. Cantrell

"In a cooperative study by the University of Minnesota and the U.S. Bureau of Mines, diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and in five underground coal mines. Three mines utilized diesel-powered haulage equipment and two used all-electric equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations measured. The first technique, using a micro-orifice, uniform deposit impactor (MOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of the aerosol is predominantly submicron and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance (CMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 µm. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling.Based on the results from the size selective sampling, a personal diesel aerosol sampler has been developed for measuring diesel aerosol mass concentrations. Th.is sampler uses an inertial impactor to size separate the respirable aerosol at 0.8 µm. All material less than 0.8 µm is collected on an after filter for subsequent gravimetric analysis."

Jan 1, 1990

By R. M. Winslow

"The phosphorus content of an iron ore is a determining factor as regards the value of the ore and also its metallurgical treatment. If some method of treatment, such as concentration, leaching, etc., could be used and the phosphorus con- tent of the ore reduced, it would be an important advancement in the iron mining industry towards the utilization of high phosphorus ores. Large bodies of material toe high in phosphorus to be marketable under present conditions would be made available, and a great deal of ore from the Cuyuna Range and other places, which is relatively high in phosphorus but otherwise suitable for making spiegel, could be reduced in phosphorus content sufficiently to permit its use in furnaces producing speigel.The form in which phosphorus occurs in iron ore is a much disputed question and it probably varies with the type and location of the ore. The statement has been made that ore piles on long exposure to the atmosphere often decrease in their phosphorus content. (Emmons, S.F. - Ore deposits, 1913, p. 652; Leith, C.K., Mesabi iron bearing district, U.S.G.S. Monograph 43, 1903, p. 275) There is described below experiments on the leaching of iron ores high in phosphorus, to determine whether it was economically possible to reduce the phosphorus content appreciably by leaching. As the research had a practical as well as a theoretical application, only low concentration of acids and alkalies were used.A number of variables were tried, among these being: (1) The solvent used, (2) strength of the solvent, (3) volume of solution used, (4) time ore was agitated (5) type of ore, and (6) screen size of the ore. The amount of ore taken was kept constant."

Jul 1, 1921

By Thomas Varley

Data on the consumption of reagents used in flotation during the years 1923 and 1924, in metallurgical plants in the Unites States, are presented in this paper. Two previous reports Lave been issued by the Bureau of Mines on consumption of oils and other reagents used to flotation - namely, "Statement of Flotation Oils," by O. C. Ralston, issued in 1913, and Serial No. 2203, "Consumption of Reagents Used in Flotation," by Thomas Varley, for the year 1919, issued in January, 1921.

Jan 1, 1925

By Ben E. Argyle

"The tungsten area in southern Mecklenburg County, Virginia, was studied by the Bureau of Mines during the period August 1944 to March 1945. The explorations were an expansion of the work done by the Bureau in 1943 in the tungsten area of Vance County, North Carolina, which joins Mecklenburg County on the south.3/Outcrops of quartz veins in the area were searched for and examined, and the only Promising showing found (a vein on the Gladys N. Taylor tract) was explored by trenching, test pitting, and diamond drilling (fig. 1).Mecklenburg County, Virginia, is in the southeastern part of the State, bordering on North Carolina,U. S. Highways 1, 15, and 58 traverse the County, and State and County roads provide ready access to most parts of the area.In 1942, Joseph and Richard Hamme discovered tungsten-bearing quartz veins in Vance County, Forth Carolina, and started mining and milling the ore. The first concentrates were shipped in July 1943. In August 1943, the Hamme holdings were acquired by Haile Mines, Inc., who continued the mining operations.The Bureau of Mines began exploratory work in North Carolina in June 1943. Reconnaissance work showed that the mineralized belt extends north-ward into Virginia. The Kimball tract, which joins the Taylor property on the north, was explored in 1943 by trenching and drilling by the R. G. Lassiter interests of Raleigh, Y. C., with disappointing results.The topography of the district is mature and characterized by wide, shallow valleys and low, rounded ridges. The main ridges trend northeast. Most of the area ranges from 300 feet to 400 feet above sea level.The relief apparently is controlled by resistant quartz lenses and the associated hard, silicified zones. The enclosing schists and granites are usually deeply weathered. Consequently, most of the quartz veins are found on the ridges."

Apr 1, 1946

By Lars Osen

The Bureau of Mines investigated (1) the effect of torsion on yield and ultimate strengths of bolts when the torsion is applied first and tensile load is applied independently of torsion and (2) various methods of increasing the tension-torque ratio and/or narrowing the data spread of the tension-torque relationship. A special torsional attachment was fabricated to attach to a universal testing machine to independently subject rock bolts to combined tensile and torsional loads. It was found that initially installed torsion is nullified during tensile loading and the tensile yield and ultimate strengths are not significantly reduced. Lubricating various components of a bolt assembly or using hardened washers will improve the tension-torque relationship during conventional installation; however, the torsional load is not nullified during this type of loading. Hence, a bolt is subjected to a combined stress throughout the loading cycle; the yield point will thus be lowered compared with the pure tensile yield if care is not taken during installation to stay below the torsional yield.

Jan 1, 1966

By H. H. Schrenk

[A colorimetric method5/ for the determination of benzene in amounts as low as 0.001 mg has been developed recently at the U.S. Bureau of Mines Pittsburgh Experiment Station by the authors, with the assistance of chemical personnel fro a the Allegheny County (Pa.) Relief Works Division. The method is based on the direct nitration of either liquid - or gas - phase benzene, followed by neutralization, extraction with butanone, and final treatment with sodium hydroxide which produces a violet color. The color is matched with color standards of known values. Although the method is adaptable to many conditions the primary objective was a procedure that would be suitable for hygienic investigations. The development worth included a study of possible interference by chemicals that be present in those situations in which the method. would be employed. In this study it was found that a specimen of hexane prepared by the Gulf Research Laboratory, Pittsburgh, by fractionation of West Virginia natural gas gave positive result for benzene, whereas a specimen of pentane prepared in the same manner showed only a trace, and specimens of n -heptane and octane (2,2,4 trimethylpentane) supplied by Eastman Kodak Co. save a negative result. According to information obtained from the Eastman Kodak Co. the latter two compounds were highly purified, the n-heptene being prepared from line and the octane synthesized in the laboratory. On nitration of a larger amount of tae natural hexane a visible quantity, of needlelike crystals which resembled those of m-dinitrobenzene was obtained. The hexane from this nitration was recovered by distillation and again nitrated, but no crystals or colorimetric indication of benzene was obtained. This imitated that the specimen of natural hexane contained a substance which at least had the chemical behavior of benzene.]

Jan 1, 1935