Search Documents

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Boone County, W. Va., as determined by the Bureau of Mines. It is one of a series describing the coals suitable for producing metallurgical coke, either as mined or after beneficiation. Over 6.3 million tons of coal was produced in Boone County, W. Va., in 1959, of which almost 5.5 million tons was mechanically cleaned in eight preparation plants. On December 31, 1959, it was estimated that almost 8 billion tons of coal remained in the county in beds 24 inches or more in thickness. Thirteen samples were collected from nine coalbeds and washability tests were made on these samples.

Jan 1, 1961

By L. B. Pankratz

High-temperature heat-content values of pure lutetium sesquioxide and dysprosium sesquioxide were measured over the temperature range from 298° to 1,800° K. Similar data for cerium sesquioxide were calculated from measurements of a mixture of cerium sesquioxide and dioxide and known values for cerium dioxide. The results for lutetium sesquioxide are regular. Dysprosium sesquioxide has a minor thermal anomaly near 1,590° K, the extra heat absorption being 220 cal/mole, Hexagonal cerium sesquioxide undergoes a transformation around 1,050° K, which is only slowly reversible; consequently results were obtained for both the low- and high-temperature varieties. The original heat-content data are reported, and smooth values of heat content and the corresponding entropy increments are tabulated. Equations were derived to represent the heat-content values.

Jan 1, 1963

By Gregory P. Cole, Jeffrey Shawn Peterson

The Pittsburgh Research center3 conducted research to study and improve electrical fault detection on coal mine direct-current (dc) trolley systems. A suspended trolley line delivers power at voltages of 300 or 600 V dc to the haulage equipment and other loads. Roof falls or other accidents may force the trolley line down so that an electrical fault current may flow between the trolley line and rail. This fault current could result in localized heating, arcing, and perhaps fire. Such faults are not always preventable by the existing circuit protection because the current magnitude is well below typical operating levels of the trolley system. The research discussed in this report studies the applicability of computerized signal analysis techniques to solve this problem. Tests were conducted at cooperating coal mines. Measurements were taken during normal loading of the trolley system (light, intermediate, and heavy traffic), during induced fault conditions (arcing and bolted faults), and during transitions between the two. These data were then used to train and test a microprocessor-based fault detection algorithm. Later, field tests of the detection algorithm found that it correctly classified the state of the trolley system greater than 95% of the time.

Jan 1, 1997

By Doris M. Hyde

Mineral industry activity in many of the smaller Caribbean Island countries has remained minimal. For this reason, specific references to Bermuda, Guadeloupe, Martinique, and the Netherlands Antilles have been removed from textual and trade table presentations. Any significant future developments will be reported as they occur. Readers are referred to earlier Minerals Yearbook editions for previous information. Table 1 production statistics have been modified in some instances. References to certain nonmetal commodities were eliminated because information has often been unreliable. Their inclusion in table 1 was not considered important to either an overview of the area or to compatibility with volume I of the Minerals Yearbook.

Jan 1, 1984

By Gregory M. Molinda

The Bureau of Mines conducted an investigation into the occurrence of outbursts of salt known to be responsible for explosions, fatalities, and damage in domal salt mines. The purpose of the investigation was to develop a basis for predicting these outbursts based on geologic and associated physical properties of salt. The investigation was conducted at the Cote Blanche salt mine in southern Louisiana. Because outbursts are the primary mode of methane emission into the mine, more than 80 outbursts, ranging in size from 1 to 50 ft in diameter have been mapped. These outbursts generally are aligned and elongate parallel to the direction of salt layering. More than 200 salt samples, both random and selected, were tested for methane content. It was found that outburst zones are well correlated with high methane content. Detailed mapping also revealed that the zones are well defined, with salt crystal size abruptly increasing upon entry into the zone. The intensity of folding and kinking of the salt layering within the outburst zone also appears to increase. An interbedded sand layer occurring throughout the mine does not appear to be a significant source of methane. However, fine-grained salt may be related to outburst occurrence.

Jan 1, 1988

By K. C. Strebig

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory with a drill instrumented to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation, and an equation representing the bit performance was derived from the mathematical theory of reliability. The coefficient of friction in drilling increased with the use of additives, although the wear coefficient decreased. The decrease in wear associated with an increase in energy per unit volume consumed and the increase in penetration rate resulted in a net decrease in the cost per foot of drilling. A hypothesis explaining the effects achieved with the additives is given.

Jan 1, 1971

By A. Visnapuu

The Bureau of Mines investigated carbonyl processing techniques for the recovery of the critical metals Ni, Co, Mn, and Cr from domestic primary and secondary sources. In most cases, the source materials require reductive precarbonylation treatment to metallize the contained Fe, Ni, and Co compounds to render them reactive with CO. The critical metals were recovered either by direct conversion to the respective carbonyls or as upgraded products by carbonyl removal of an undesirable metal. Best metal-to-metal carbonyl conversion was under CO pressure, from 80 atm upward, and at 1400 C. Carbonylation was accelerated by the addition of HzS in small quantities. CO pressure, temperature, promoter and pretreatment trends, and other factors enhancing metal carbonyl formation are presented.

Jan 1, 1987

By R. V. Lundquist, H. Leitch

Sodium aluminate is the principal aluminum compound formed in the sinters prepared by the lime - soda sinter process for recovering aluminum from silicate source materials . The properties and characteristics of this compound were studied to improve the efficiency of the process . Crystalline sodium aluminate was prepared by sintering stoichiometric quantities of soda ash and calcined alumina for 1 hour at 1,250 ° C. The extent of aluminum extraction from sodium aluminate was determined in water and in solutions of NaOH and Na₂ CO3 . Nearly complete extraction of aluminum from sodium aluminate was achieved only in solutions containing free NaOH in excess of that supplied by the salt through hydrolysis . About 42.2 to 68.8 percent of the aluminum was extracted in water or in solutions of Na₂ CO . The precipitation of alumina trihydrate from sodium aluminate solutions was shown to be part of a continuous , reversible reaction according to the equation Al (OH ) A1 (OH )3 + OHThe reverse reaction dissolves alumina trihydrate in NaOH solutions to produce sodium aluminate . Approximate equilibrium concentrations were determined for the reaction at 30° , 50 ° , and 70 ° C. False apparent equilibrium conditions for the dissolution reaction appear when only a small excess of alumina trihydrate is present in the NaOH solutions . A large excess of alumina trihydrate must be present before the true equilibrium point is assured . The engineering significance of the data is summarized , showing controls that should be exercised for a successful and efficient process .

Jan 1, 1964

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. DATA INPUT FOR THE OPERATING PROTOTYPE [To run the Rail Haulage Model independent of the Production Sub-system, remove the production data from card type four through the blank card following END DATA on page B18 and change the fourth data element under ADDITIONAL DATA from 1 To 0.]

Jan 1, 1974

By Donald W. Mitchell

The fire hazard of neoprene, polyvinyl chloride, and rubber conveyor belts was studied at the Federal Bureau of Mines Experimental Coal Mine. The effects of intensity of ignition source, velocity of the ventilating air, and type of belt were investigated at three levels in small-scale gallery experiments. Studies were made in the mine on the effects on ignition and flame propagation of belt-entry dimensions, belt widths, and belt configuration. Methods for extinguishing belt fires were also investigated under simulated mining conditions, and during these trials coal dust and grease were placed on the belt. The research showed that conveyor belts will burn. Neoprene, polyvinyl chloride, and rubber belts, with and without carcass, ignited and propagated flame. The highest rate of flame propagation was obtained on rubber belt. The fire hazard increased with increase in intensity of ignition source and air velocity. Flame propagated only when air was forced through the test zone; propagation was not obtained when forced ventilation was not used, as would exist in a neutral entry in a mine. Automatic water sprays and high-expansion foam effectively arrested flame propagation; direct application of water and bicarbonate dusts was ineffective.

Jan 1, 1967

By D. S. Colby

The productive capacity of natural gasoline and cycling plants in the United States or. January 1, 1954, was 926 thousand barrels per day, according to the Bureau of Mines biennial survey. This represented an increase of 114 thousand barrels per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 164 thousand barrels per day. The total number of plants increased from 521 on January 1, 1952, to 535 on January 1, 1954. The number of operating plants increased from 506 to 521. The major increases in capacity took place in Texas, Illinois, Oklahoma, Louisiana, and New Mexico, with the absorption-type plant continuing to account for most of the new construction. In 1954, however, 6 plants reported using a refrigeration process whereas only 1 plant reported this in 1952. The number of operating compression-type plants continued to decline and combination plants showed a decline this year because a number of these plants were reclassified as absorption-type.

Jan 1, 1954

By Don B. Hunter

The Bureau of Mines investigated the extraction of alumina from calcined kaolin by leaching with boiling RCI in a train of three 50-gal continuous, stirred reactors. Slurry discharged from the reactors con-tained an excessive amount of fines, which impeded solid-liquid separation. Autogenous grinding of coarse solids that accumulated in the reactors was the source of the fines. This report describes modifications to the reactors and to the operations that led to decreased fines generation and improved solid-liquid separation. Modifications to the reactors included custom-made impellers, the addition of a baffle system, a subsurface slurry discharge system, and slower rotation of the impellers. Concurrent testing of a continuous horizontal belt filter showed that the form filtration rates were increased from 350 to almost 1,000 Ib/h+ ft-2 when the modified reactors were used.

Jan 1, 1984

By H. Billmayer

This report covers the period from June 17, 1974 to February 20, 1975, and describes the work performed in compliance with the requirements of Contract No. H0346102 and Modification No. 1 thereto. The purpose of the contract was to design protective canopies for an Elkhorn Scoop, a Lee Norse Miner, a Wilcox Miner and a Wilcox Bolter; to construct mockups of the canopies; and to obtain machine operator evaluations of the canopy designs by assessing the mockups while installed on their machines in the mines. The overall program objective was to achieve protective canopy designs for the four machines which would be acceptable to the operators.

Jan 1, 1975

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By J. D. Sargent

Selenium might be described as a paradoxical element, being a metal or a nonmetal, a conductor or nonconductor, amorphous or crystalline, colorant or decolorant, and a hydrogenator or dehydrogenator. Selenium was discovered in 1817 by the Swedish chemist, Berzelius, while studying flue dust from the lead chambers of the sulfuric acid works at Gripsholm, Sweden.

Jan 1, 1954

By N. E. Hanna

The effect of small percentages of sodium chloride on the incendivity of permissible explosives was studied by the Bruceton up-and-down technique in gallery tests. Both the reduction in incendivity achieved by addition of sodium chloride and application of the test method to explosives evaluation are discussed. It is demonstrated that the up-and-down technique in gallery testing is suitable for distinguishing differences in incendivity between different explosive compositions and between lots of the same composition. The study also shows that addition of relatively small quantities of sodium chloride tends to reduce the incendivity of explosives to firedamp, but addition of sodium chloride cannot insure reduced incendivity. Any improvement attributable to the salt can be counteracted by undefined variations in the explosive. The need for experimental investigations of a number of factors that may affect the safety of permissible explosives is emphasized. ACKNOWLEDGMENTS Grateful acknowledgment is made of the assistance of Roy L. Grant in analyzing for normality of distribution of the data obtained by the up-and-down methods and to Harold E. Tubbs for numerous calculations.

Jan 1, 1959

By G. F. Friel

A series of experiments in the U.S. Bureau of Mines Safety Research Coal Mine at the Pittsburgh Research Center evaluated the effects of crosscuts on the travel time of carbon monoxide (CO) along an entry to improve the accuracy of a mine-fire locator program. Three entries, ten single crosscuts, and three double crosscuts were instrumented with CO sensors. One-percent CO in nitrogen was released and monitored as it traveled the entries. In addition to dispersion of CO at the front of the CO wave, CO was entrained from the entry into the crosscuts. It was determined for an entry and single-crosscut configuration that the measured travel time for a concentration change of 5 ppm was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and crosscut volumes. For an entry and double-crosscut configuration, the measured travel time for the same concentration change was 25% greater than the predicted time based upon entry volume only, but 10% less than the predicted time based upon entry and crosscut volumes. An effective dispersion coefficient for CO dispersion along one of the entries was estimated to be 1.5 m2/ s.

Jan 1, 2010

By Lloyd A. Morley, Robert Stefanko

Table

Jan 1, 1974

By Robert P. Vinson

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

The head loss data for coal slurries over a range of concentrations and velocities and the laboratory screen analysis were selected as areas for investigation in the data analysis performed. The analysis resulted in the following: (1) Size distributions for the coal used in the horizontal pipeline tests were fitted to the Rosin - Rammler distribution function. Each of the fits was significant. Corresponding Rosin - Rammler parameters were obtained which were introduced into the regression analysis. (2) A regression equation was obtained which predicts the slurry head loss of 1-inch by 0 coal slurries ranging in volumetric concentration from 20 to 40 percent and line velocities from 1 to 14 feet per second as a function of the square of velocity. The addition of the term for concentration in the regression equation did not contribute significantly c head loss.

Jan 1, 1972