Search Documents

By A. J. Forney

A high-Btu gas was made at the Bruceton, Pa., laboratories of the Bureau of Mines to demonstrate the feasibility of using the gas as a nonpolluting fuel for automobiles. The pilot plants at Bruceton were revised to combine the processes of coal gasification, gas purification, and catalytic methanation in one overall system. Tests in the Bureau's test automobiles at Bartlesville, Okla., showed the Synthane gas was less polluting than natural gas.

Jan 1, 1972

Provide reasonably priced, reliable fire protection for front-end loaders. Approach Automatic fire sensing and suppression systems were developed and ruggedized for use on front-end loaders operating in harsh mine environments. How It Works Temperature sensors mounted in the loader's engine, transmission, and articulation areas detect the heat from a fire while it is still small and controllable. This triggers the release of the ABC class dry chemical extinguishing agent through a fixed piping system onto the fire. The system can also be manually activated from either the cab or ground level. Locations of the principal components of the system are shown in the drawing. Two control subsystems were designed to respond to varying fire protection needs and mine conditions. One subsystem only initiates discharge of the extinguishing agent. The other subsystem initiates visual and audible operator alarms if there is a fire sensed or if there is a fault in the control circuit.

Jan 1, 1979

By R. N. Roby

In the course of the Bureau of Mines investigations for suitable sources of high-aluminum clay for the production of alumina, the Whiteware clay deposit was examined in August 1942 by G.N. Bennett, mining engineer, Bureau of Mines, Montana District Office. This report presents the factual data obtained by the investigation, which also includes data on trenching and drilling, and the results of some refractory tests and chemical analyses of representative samples of the clay later taken from some of the best trench exposures and from adit dumps.

Jan 1, 1949

By L. Cheng

This report describes a laboratory investigation of the effectiveness of low-pressure steam and a steam-water spray sequence for the collection of airborne respirable (<10 µm) coal dust. Comparison of present results to previous results obtained with water spray alone indicates that the use of steam in a steam-spray sequence increases the collection efficiency by about 14 percent over that obtained by water spray alone. However, the use of steam to collect airborne dust requires cooling the steam-dust mixture in order to achieve condensation of the steam, and steam does not appear to be an attractive approach for collecting airborne dust in underground coal mining operations.

Jan 1, 1974

By John C. Franklin

A radon survey was made at five different locations in the Twilight mine near Uravan, Colo., to determine chances in radon concentrations in an inactive mine. Data were taken with a continuous monitor set for 1-minute count periods and readings were taken 24 hours a day for 9 days. The 12 readings per station each hour accurately showed how t w radon concentration varied during the day. From the data collected from the intake portal to station 4, the average radon emanation rate was estimated at 18 picocuries per second per square foot (pCi/sec/ft3). A daily cycle in radon concentration was detected that apparently was related to barometric pressure change.

Jan 1, 1976

By E. D. Eastman

There are three researches upon the specific heat of water vapor by the method of explosion that are sufficiently advanced in technique and suitable in plan to justify careful study of their results , with the double purpose of fixing the best available experimental values and indicating the attainable accuracy of the method. These three researches comprise the work of Pier , Bjerrum , and Siegel.5 The work of earlier date than Pier's suffers from obvious inaccuracy of measurement , while the experiments more recent than Siegel's , such as those of Womersley6 , of Bone and his collaborators , and of Maxwell and Wheeler , 8 are for the most part not well designed for the accurate determination of the heat capacities in question . Some of the errors to which they are especially subject have been discussed by David and by David and Thorp.

Sep 1, 1930

By A. S. Prokopovitsh

A spectrophotometric method for the determination of small amounts of copper in tungsten metal powder using the principle of solvent extraction has been developed by the Federal Bureau of Mines. The metallic sample is dissolved in hydrogen peroxide, tartaric acid added, the pH adjusted, and the excess peroxide destroyed by boiling. Copper is reduced to the cuprous state, and the reagent neocuproine (2,9-dimethy1-1,10-phenanthroline) is added to form a colored complex with the copper. This colored complex is then extracted into chloroform and the absorbance of the separated chloroform layer measured on a spectrophotometer. Copper contents as low as 1 p.p.m. (parts per million) can be determined. The method is limited to finely divided tungsten powder. The interest of the Bureau of Mines in developing more sensitive methods for the determination of trace impurities in high-purity tungsten prompted an investigation of the possibility of using solvent extraction-colorimetric methods. The organic reagents now commercially available make possible many extremely sensitive colorimetric methods for the determination of metallic ions. Extraction of the colored complex into a small volume of organic phase can be used to further increase sensitivity (4) .4/ This general approach has the added advantage that no special equipment beyond that normally found in an analytical laboratory is required.

Jan 1, 1961

By A. C. Johnson

This report is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods, and costs at various mines in the United States. It describes operations at the Black Rock mine, Wah Chang Mining Corp., Mono County, Calif. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods, practices, and costs. The Black Rock tungsten mine of the Wah Chang Mining Corp. is 33 miles north of Bishop, Calif., in the Benton Range, Mono County, Calif. The property was acquired in August 1950 and a well-planned program of exploration, development, and exploitation resulted in a good production record with low costs. Operations were halted in July 1957, about 6 months after suspension of the tungsten purchase program by the Federal Government.

Jan 1, 1960

By B. J. Scheiner

Extraction of molybdenum from molybdenite ore by an electrolytic oxidation procedure was investigated by the Bureau o f Mines. Various parameters affecting molybdenum extraction, such as salt concentration, temperature, treatment rate, current density, and particle size, were studied. Molybdenum extraction of 95.2 percent was achieved on a laboratory scale from an ore containing 0.35 percent molybdenite. Corresponding power consumption was 24 kwhr per pound of molybdenum extracted with a base consumption of 4.5 pounds of sodium carbonate. Laboratory and pilot plant experiments are in progress on low-grade molybdenum concentrates containing rhenium and copper. Preliminary results indicate that molybdenum extractions in the 90- to 99-percent range and rhenium extractions of 93 to 99 percent can he obtained without appreciable oxidation of associated copper minerals.

Jan 1, 1972

By K. E. Stanfield

Oil-yield results are presented for 65 oil-shale sections in Piceance Creek Basin, Colorado, sampled during the period 1957 through 1963. Including previously published data, oil-yield results for 203 sampled sections have now been released by the Bureau of Mines to aid in appraising the shale oil potential of the basin. Oil yields of core samples (135 sets) were regarded as reliable bases for appraising the Mahogany-zone interval, but only 5 sets of cores sampled the deeper, lower-zone oil shales. Drill cuttings (68 sets) sampled the lower-zone oil shales, but their oil yields are principally indicative and should be confirmed by analyses of cores. More complete core sampling of the lower-zone oil shales is needed.

Jan 1, 1967

By C. J. Thompson

Two sulfur compounds--the 2,2,5-trimethyl- and the 2,2,5,5-tetramethyl derivatives of thiacyclopentane--were identified in Wilmington, Calif., crude oil, using microdesulfurization and gas-liquid chromtography techniques.

Jan 1, 1963

By Frank A. Peters

This Bureau of Mines report is the second of a series of process evaluations planned to determine the relative processing costs of producing metallurgical-grade alumina from low-grade aluminous materials. Included in these evaluations are recommendations for additional research and development to improve the processes and to lower their costs. The design for each process is based on published work. The processes considered in this report are designed to extract alumina as aluminum chloride from calcined clay with 20 percent hydrochloric acid and to remove the silica residue by filtration. Iron is removed by one of the following processes: Isopropyl ether extraction, in which iron chloride is extracted before decomposing the aluminum chloride; gas precipitation, in which the aluminum chloride is precipitated with hydrogen chloride while leaving the iron chloride in solution; gas precipitation-isopropyl ether extraction, in which the aluminum chloride from precipitation is extracted with isopropyl ether, if necessary; caustic purification, in which a crude alumina is produced and then purified by a modified Bayer operation; or sinter purification, in which a crude alumina is produced and then purified by a lime-soda sinter operation. For plants producing 1,000 tons of alumina a day the estimated operating costs per ton of alumina are: [Isopropyl ether extraction process $ 65.09 Gas precipitation process 89.04 Gas precipitation-isopropyl ether extraction process 119.65 Caustic purification process 73.79 Sinter purification process 80.47] The estimated fixed capital costs per annual ton for these plants on a Marshall and Stevens chemical equipment basis of 240.0 are: [Isopropyl ether extraction process $229.03 Gas precipitation process 287.16 Gas precipitation-isopropyl ether extraction process 356.59 Caustic purification process 266.48 Sinter purification process 279.13]

Jan 1, 1962

By J. A. McAllister

In the course of a study of domestic Manganese resources, 2-ton representative samples of ore were taken by Bureau of Mines&apos; engineers from the Payday claim, Weber County, and the Newcomb-claims, Rich County, Utah. The Payday No. 1 deposit is situated 13 miles northeast of Huntsville, Weber County, Utah. The manganese ore is a. replacement deposit in limestone and consists of manganese oxides imbedded &apos;in clay and also as the cementing agent consolidating small pebbles and pieces of quartz and limestone.

Jan 1, 1949

By Mary F. Koehler

Interoxidic compounds, such as vanadates, have not been studied extensively in the field of thermodynamics. This is a report of three vanadates of sodium--metavanadate, pyrovanadate, and orthovanadate. Vanadates of other metals will be considered in future reports. The heats of formation at 298.15° K. of the three sodium vanadates (both from the oxides and from the elements) were derived from the results of sodium hydroxide solution calorimetry. Free energies of formation were obtained by combining heat and entropy values. The results support the conclusion that the three sodium vanadates were stable with respect to all possible decompositions in which vanadium retains its pentavalency.

Jan 1, 1960

By Gerald W. Elger

A new process under development by the U.S. Bureau of Mines for producing synthetic rutile from ilmenite is described. Rutile formation is based on oxidation and fluxing of titania slag produced by electric furnacing of ilmenite. Laboratory tests show that phosphorus pentoxide flux additions to oxidized slag enhance conversion to rutile by forming a phosphate-based glass matrix. This matrix contains most of the major impurities, including the oxides of iron, aluminum, magnesium, manganese, and silicon. Rutile crystals of 5 to 150 microns in size were formed in slags heated to temperatures of 800° to 1,550° C. The synthetic rutile crystals were liberated from ground slag by treating with phosphoric acid to weaken the glass matrix, followed by attrition scrubbing. Rutile fractions analyzed as high as 94 percent titania content. In several instances, more than 90 percent of the titanium in the shag was recovered to yield combined rutile fractions containing 90.2 to 92.6 percent titania.

Jan 1, 1971

By Phillip N. Yasnowsky

This Bureau of Mines report examines the percentage depletion allowance rate structure in relation to several criteria that are indicative of U.S. mineral import dependence. These criteria are the minerals considered as strategic and critical for stockpiling purposes, the ratio of reserves to forecast cumulative demand (1976-2000) for selected minerals, and the U.S. net import reliance as a percentage of apparent consumption (1978), also for selected minerals in general, it was Found that there does exist a direct, although not perfect, relationship between the percentage depletion allowance rates and the degree of import dependence as indicated by these three criteria. The higher percentage rates tend to he associated with those minerals for which the United States is, or will likely he, heavily dependent on foreign sources. In addition, a basic discussion of the mineral depletion allowance is provided, including numerical examples illustrating the computation of the allowance under several assumptions. Also, the percentage depletion allowance rates for individual minerals are tabulated.

Jan 1, 1980

By W. H. Ode, W. A. Selvig

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County Colo., in connection with a survey of carbonizing properties of American coals 4/ and investigations of their chemical and physical properties. 5/ The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the as from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

May 1, 1937

By Charles Vaught, Richard S. Fowkes, Ronald S. Conti, Barbara Fotta, William J. Wiehagen

The purpose of this study was to determine mine workers&apos; state of fire-fighting preparedness and the technology being used to detect and respond to underground coal mine fires. To investigate this problem, 214 underground coal miners were interviewed by U.S. Bureau of Mines researchers. Frequency distributions of workers &apos; responses are presented in this report, along with segments of narrative accounts, to profile miners&apos; fire-fighting capabilities. The data indicated that much variability exists from mine to mine and that there are several important changes operators may undertake in order to make miners better prepared to deal with fire underground: select appropriate sensors, establish and test a warning and communication protocol, construct a system capable of delivering hundreds of gallons of water per minute for sustained periods, institute formal fire preparedness audits, develop case studies of events that occur at an operation to use as teaching and assessment tools, and provide structured practice that can be incorporated into fire drills.

Jan 1, 1995

By R. Karl Zipf

In some instances, extensive room-and-pillar working scan collapse with little warning and pose a serious risk to underground miners. Traditional strength-based pillar design methods applicable to coal or hard-rock mines use a factor of safety defined as pillar strength divided by pillar stress. Factor of stability, defined as local mine stiffness divided by post-failure pillar stiffness, may offer a way to design room-and-pillar mines and eliminate collapses. Three alternative design approaches to decreasing the risk of large-scale catastrophic collapses are described: the containment approach, the prevention approach, and the full-extraction approach. Until good data on the post-failure behavior of pillars become available, the containment and full-extraction options are the safest. The limitations in our ability to evaluate both the stability of old workings and the long-term performance of room-and-pillar mines are described.

Reduce the potential of haulage related injuries in underground mines by providing a method for quickly assessing the state of repair of mine haulage track. The Problem Currently, there are no established standards or procedures for inspection or cleaning of underground mine haulage track. Many track defects are hidden from an inspector because of layers of dirt and debris on the ballast, spikes, fishplates, etc. When a visual inspection can be performed, it may be highly subjective, except for a few items that can be categorized or counted, such as missing bolts or spikes. Track inspectors may even become tolerant of defects that can gradually worsen. For these reasons, mechanical inspection methods are needed to supplement visual inspections. Approach The Bureau investigated this problem and designed a towed vehicle to both mechanically clean and inspect underground coal mine haulage track. The vehicle was developed using a systems approach, paying particular attention to human factors issues such as operator field of view, operator ingress-egress, control positioning, and seating design. The prototype was built using simple fabrication techniques and off-the-shelf components.

Jan 1, 1990