Search Documents

By Raymond M. Stateham

The Bureau of Mines evaluated temperature increases on the heads of resin-grouted bolts as indicators of the integrity of the anchoring of the bolt. Expected increases were calculated by the finite difference method; the calculations were checked by bolthead temperature measurements, both in the laboratory and in the field. The accuracy of the calculations varies with the validity of assumptions necessary to the process. Measurements in the laboratory produced a temperature rise of about 4.00 F on the head of a 4-foot bolt when installed with a full column of resin. This increase remained for about 30 minutes. Similar increases were noted on bolts installed at the White Pine mine, White Pine, Mich., but bolthead temperature increases in the mine lasted only about 10 to 15 minutes. When partial columns (reduced amounts) were used, the temperature increases were smaller.

Jan 1, 1976

By D. A. Lucero, J. E. Brockmann, L. A. Mondy, K. L. Rubow, D. J. Rader

"Department of Mechanical Engineering, University of Minnesota, Minneapolis, MNExperimental and correlated stage responses (the fraction of particles entering an impactor that are collected on a stage) are presented for the Andersen Mark III and Marple personal cascade impactors. The impactors were operated upright and fully assembled so that interstage interference and wall losses could be properly studied. The observed stage responses showed maxima that fell significantly short of unity, meaning that a monodisperse aerosol is never collected exclusuvely on one stage, but is distributed among several stages and internal losses. Correlations for the stage responses are presented so that the experimental results can be used to determine size distributions with available data-inversion algorithms. Simulations with log-normal distributions show significant differences between dpa50 histograms and the more accurate distributions that result by taking the response functions into account.Cascade impactors are widely used for the measurement of aerosol size distributions; their ruggedness and simplicity of operation make them an attractive choice for a variety of environments. In one common application, the aerosol of interest is drawn through the impactor, and the amount deposited on each stage is determined gravimetrically. The primary objective is to extract as much information as possible about the initial size distribution from the resulting set of weights. Unfortunately, the reconstruction of contin-uous size distributions from finite data sets is an ill-posed problem. Not surprisingly, a variety of such reconstruction techniques are presently in use; the success of each method depends on the particular nature of the aerosol sample and the instrument response.Inversion of impactor data by any of these techniques requires that the response functions for each stage be known. The stage response function gives the fraction of particles entering the impactor that deposits on that stage. Values of the response function range from zero to one, and depend on impactor operating conditions (e.g., geometry, flow rate, and gas properties) and particle properties (e.g., diameter, density, and shape factor). As interstage interferences and particle losses will affect each stage's response, experimental determination of stage responses should be made for fully assembled impactors. Unfortunately, impactor stage response functions are rarely reported; rather, single-stage efficiency curves are given that provide an incomplete description of impactor performance.This paper presents experimental stage responses for two fully assembled cascade impactors: the Andersen Mark III and Marple personal impactors (model 298, Andersen Samplers, Inc., Atlanta, Ga.). These calibrations were performed with monodisperse liquid droplets for both impactors and also with monodisperse solid spheres for the Marple personal impactor. The calibration results for the Mark 111 impactor presented here have been previously reported in the response-function format (Rader et al., 1989). The calibration results for the Marple personal impactor, however, were originally presented in the single-stage efficiency for¬mat (Rubow et al., 1987) and have been reanalyzed in this work. Losses within both impactors are considered, and their treat¬ment within data inversion techniques is dis¬cussed. In addition, correlations for each impactor's response functions are presented so that these calibration results can be easily included in data-inversion algorithms. Size distribution inversions using these response correlations are compared with the standard cut-point method for two lognormal test dis¬tributions."

Mar 1, 1992

By Robert N. Roby

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are made primarily to provide preliminary information to Department of Interior agencies and others concerned with the planning of the proposed Federal power developments within the Missouri River Basin . The present report has been designed to permit public distribution of the factual data obtained . The field investigations in Meagher County were made during tually all 1948 ; Vir- known metallic mineral occurrences within the county were investigated ; some nonmetallic mineral deposits also were investigated . The investigations cannot be considered complete , however , because some long-inactive mines or prospects may have been missed . Most of the old mine and prospect openings are caved; many are completely inaccessible . Many of the claims located years ago have been abandoned ; others have been relocated under different names and ownerships . Because of such conditions , much of the information regarding their development and operation necessarily has been obtained from Federal and State publications , supplemented by information provided by owners and local residents .

Jan 1, 1950

By Jr. Norman

The Bureau of Mines investigated the thermoelectric properties of yttrium selenides and tellurides from room temperature to 900° C. X-ray crystallographic data were determined for the yttrium-selenium and yttrium-tellurium compounds that were orthorhombic with a cubic substructure. The yttrium selenides and tellurides exhibited semimetallic to insulator conduction properties with figures of merit of 10-9 to 10-4 °C-1. The mono-selenide and monotelluride behavior was partially degenerate; unsatisfied bonds were the source of the large number of charge carriers. The higher stoichiometry selenide compounds were intrinsic semiconductors) but with high electrical resistivities. A critical defect or impurity ionization energy for carrier activation appeared to exist in the majority of telluride compounds. Mobility and energy band determinations are required to interpret completely the observed effects in most of the compounds studied.

Jan 1, 1966

By Harold E. Heide

The United States is the world's largest consumer of tin and depends entirely upon foreign imports for its major source of supply. Only a small quantity of tin is produced on the North America continent. The advent of the war in Europe in 1939?brought a threat to our foreign sources of supply, and the Congress took steps to forestall shortages of tin and other metals. By authority of the Strategic Minerals Act, passed by Congress in 1939, and subsequent legislation, the Bureau of' Mines ?and Geological Survey conducted investigations of domestic tin deposits. Most of the tin that has been produced in North America came from the Seward Peninsula, Alaska.

Jan 1, 1948

By John E. Pahlman

The Bureau of Mines has conducted research on a dual leaching method that offers the potential for the economic recovery of the silver, as well as of the manganese, contained in some domestic manganiferous silver deposits. The method consists of an initial leach of manganese with aqueous sulfur dioxide (S02) followed first by a neutralization rinse, and then by a second leach with cyanide solution for the extraction of silver. Refractory silver in these ores was either (1) intimately associated with the manganese, (2) chemically resistant to cyanide leaching, or (3) rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization. Less than 10 pct of the silver was extracted when minus 2.5-plus 1.3-cm ore pieces were leached directly with cyanide. However, extractions of 25 to 82 pct of the silver and 65 to 96 pet of the manganese were attained in laboratory column-leach tests using the dual leaching method on equivalent-sized ore pieces from seven domestic deposits.

Jan 1, 1987

By R. M. Santmyers

Except for optical purposes and a few other special uses quartz and quartzite are to a considerable degree interchangeable. This also may be said with respect to pulverized quartz and ground silica sand, which are discussed in a separate paper of this series. All these materials, except perhaps quartz crystals of optical grade, are abundantly available in many parts of the United States. In the form of ordinary crushed stone much of it is sold at $1 a ton or less, and ordinarily

Aug 1, 1931

"INTRODUCTION While investigating prevention of sabotage and maintenance of production of essential war minerals, engineers of the Bureau of Mines visited more than 1,400 metal and nonmetallic mines, quarries, and open pits in all parts of the United States.The need for, uniform safety practices is indicated by the fact that during 1938-1940, inclusive, the Western Safety Conference, under the sponsorship of the California Department of Industrial Relations, undertook the prepara¬tion of a set of standard safety regulations for the 15 participating political subdivisions. The membership of these political subdivisions is comprised of representation from Alaska, Arizona, British Columbia, California, Colorado, Hawaii, Idaho, Lower California, Montana, Nevada, New Mexico, Oregon, Utah, Washington, and Wyoming, For the guidance of its own engineers; the Bureau of Nines found it necessary to prepare a set of safety practices that could be used uniformly throughout the United States. These safety practices were compiled from State mining regulations, mining company safety rules, and the experience of Bureau of Mines engineers for more than 3 decades, and represent the best safety practices of the Nation's' mineral industry.The purpose of this publication is to make safety practices available for the non-coal branches of the mineral industry, with the hope that they may assist in reducing accident occurrence. The Bureau will welcome questions and suggestions regarding these practices in order that changes may be made as necessary.Where the adoption of any practice would not materially increase the safety of employees or would work undue hardship on the operator, the Bureau does not recommend such adoption."

Sep 1, 1946

By J. A. Organiscak

The Bureau of Mines recently investigated dust generation and methane liberation during half-and full-web cutting at a double-drum shearer longwall face. This study was conducted to ascertain the health and safety aspects of wider web shearing at longwalls. Results from these underground tests showed that deeper web cutting reduced dust generation and methane liberation per ton of coal mined, while significantly improving shearer production rates. When cutting with the airflow (head-to-tail cut pass) full-web cutting decreased dust generation per ton by 16 pct at the shearer and 6 pct at the tailgate, with an increase in shearer production rate of 72 pct. Methane liberation per short ton also deere~sed by 36 pet at the shearer and 22 pct at the tailgate. Full-web cutting against the airflow (tail-to-head cut pass) decreased dust generation per ton by 41 pct at the shearer and 37 pct at the tail-gate over half-web cutting, with an increase in shearer production rate of 61 pct. Methane liberation per ton also decreased by 35 pct at the shearer and 41 pct at the tailgate. These improvements for full-web cutting are a reflection of improved cutting efficiency (less dust and methane produced from cutting) and less new face area exposed per ton of coal mined (less methane liberated from face per short ton of coal mined).

Jan 1, 1988

By J. B. Gayle

The Bureau of Mines studied the effects of air oxidation on the recovery of float coal. Both batch-and continuous-type tests were made on six bituminous coals, representing the range in rank of coals now commercially used for carbonization, and on one anthracite coal. The effects on flotation recovery of oxidation at 1000 C for periods up to 50 days were investigated using an alcohol-type frother and a kerosine-pine oil reagent. Two series of release analysis tests were made, using one medium-volatile bituminous coal. Float coal recovery was adversely affected by oxidation in all tests where the alcohol-type frother was used. Conversely, a small degree of oxidation improved recovery with kerosine-pine oil frother for some of the coals in continuous tests. Prolonged oxidation (beyond about 14 days) adversely affected float coal recovery for all coals, the effect being more pronounced for batch-type tests and for tests using alcohol-type frother. Reagent selectivity for the rejection of both ash forming and sulfur bearing minerals was reduced by oxidation. Severe reduction of reagent selectivity required only about 3 days' oxidation for alcohol-type frother but more than 10 days' oxidation when the kerosene-pine oil reagent was used.

Jan 1, 1965

By M. M. Jones

A procedure for the spectrophotometric determination of uranium has been developed in support of minerals research being conducted by the Bureau of Mines. Uranium is separated from the sample by tributylphosphate extraction from acid solution containing added aluminum nitrate and (ethylene dinitrilo)-tetraacetic acid solutions. The colored uranium-dibenzoy1methane complex is developed in the organic phase by adding an ethanol solution of dibenzoylmethane buffered with triethanolamine. Absorbance is measured at 410 nanometers, and the response is linear up to at least 100 micrograms U30S in the aqueous aliquot taken for analysis. Aliquots containing as little as 8 micrograms U30S may be analyzed with relative errors no greater than ±5 percent. For aliquots containing at least 35 micrograms U308, relative standard deviation at the 95-percent confidence level is about ±2.2 percent. Appropriate procedures are given for analyzing a wide variety of samples.

Jan 1, 1980

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By L. B. Pankratz

Heat content measurements were conducted for GaPo.996 and InPo.986 over the temperature range from 298° to 1,100° K, and for In2S2.897 over the range from 298° to 1,200° K. Both the actual experimental data and values adjusted to conform with the stoichiometric compositions (GaP, InP, and In2S3) were reported. Entropy increments above 298.15° K were calculated for the stoichiometric compounds, and heat content and heat capacity equations were derived.

Jan 1, 1965

By V. M. Benson

A simplified, routine method for determining lithium in lithium-bearing rock is presented. The sample is decomposed by repeated treatments with nitric, hydrofluoric, and perchloric acids. Since this procedure does not appreciably dissolve beryl, interference by beryllium (the principal interfering cation) is minimized for most samples. The salts are brought into solution with water and enough citric acid-ammonium citrate buffer is added to make the final volumetric dilution 0.20 M with respect to citrate. The addition of citrate greatly reduces anion interference in the hydrogen-oxygen flame, slightly increases the intensity of the lithium 671 millimicron emission line, and reduces the effect of most of the interfering cations to the extent that analytical separations are not necessary. The accuracy of results of single determinations of lithium in a pegmatite containing spodumene, lithium-bearing mica, and beryl are approximately equal to that obtained by other flame methods, INTRODUCTION This investigation was undertaken in Bureau of Mines laboratories to develop a reliable, rapid, routine analytical method for determining lithium in lithium-bearing minerals. The requirements of the procedure were that the method should be applicable to the analysis of a variety of lithium-bearing ores and test products, and the results would be reasonably accurate for materials containing 0.05 to 8 percent Li20.

Jan 1, 1961

Vanadium, molybdenum, and a titanium-10 percent vanadium alloy were evaluated for their susceptibility to stress corrosion cracking in a number of corrodents. Tests were conducted utilizing conventional U-bend techniques with subsequent evaluation in a pneumatic constant-load apparatus. Vanadium and molybdenum were generally resistant to stress corrosion cracking in the media studied. U-bend specimens of vanadium showed evidence of stress corrosion cracking in 6 li hydrochloric and 18 li sulfuric acids; however, tensile stress specimens exposed to these solutions did not exhibit stress cracking. Similar results were obtained when U-bend specimens of molybdenum were immersed in 10 percent formic acid. Titanium-10 percent vanadium alloy was susceptible to stress corrosion cracking in 10-percent (2.85 li) hydrochloric acid solution. Heat treating the alloy greatly reduced its corrosion rate and its susceptibility to stress cor-rosion cracking in this medium.

Jan 1, 1965

By Earl L. Hastings

Although the principal market for diatomite in the United States is in the East,4 production of the material is presently restricted to the West, because the deposits are larger, mining costs are cheaper, and the quality of product is better than that obtained from other domestic deposits. However, Tallahatta diatomite, occurring in Choctaw and Clarke Counties, Ala., has a freight rate advantage, which should encourage competition for those market that are now being supplied with the purer diatomites from the western deposits. For this reason, diatomite occurrences in the Tallahatta formation were examined by the Bureau of Mines and physical properties of samples from the deposit were determined to obtain additional data for use by any potential producer who wished to evaluate the material for its commercial possibilities. In 1894 K. M. Cunningham5 found that the buhrstone formation (now known as the Tallahatta formation) contained "siliceous shells of marine diatoms, radiolaria and foraminifera, thus being rather of the nature of tripoli or diatomaceous earth than of a true clay." Cooke6 and Semmes7 also reported the Tallahatta formation to be composed principally of diatomaceous earth with accompanying beds of sand, clay, and sandstone.

Jan 1, 1963

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

By Bernard J. Steblay

Two instruments have been constructed that extend microseismic data collection and processing capability for Bureau of Mines research in rock burst, coal bounce and outburst, and roof fall monitoring. The first instrument is a 13-channel tape-triggering system. This system allows better utilization of instrumentation tape recorders by collecting data digitally, turning the tape on only when valid data are present, and increasing the dynamic range of the recorder by using digital data. A digital-to-analog converter is used to provide analog output of the recorded digital data. The instrument records a much larger time slice of transient events than do current commercial devices. The second instrument is a microseismic energy measurement device. This device uses recent developments In integrated circuits to overcome the dynamic range and accuracy limitations of previous instruments. The analog signal is converted to a digital one, and then high-speed multiplication techniques are used to square the amplitude value in real time and integrate it.

Jan 1, 1983

By A. R. Taylor

This report describes the design, construction, and operation of a low temperature adiabatic calorimeter for measuring heat capacities of solids or liquids from 60° to 300° K. A brief discussion of the basic theory involved in chemical thermodynamics and the problems involved in obtaining accurate experimental data is presented. The operation of the calorimeter was tested by measuring the heat capacity of a sample of benzoic acid obtained from the National Bureau of Standards over a temperature range of 60° to 300° K. The measured heat capacity values of the benzoic acid compared favorably with similar values obtained by the Bureau of Standards, the maximum deviation being 0.5 percent. THEORY A brief discussion of the basic theory involved in chemical thermodynamics will illustrate the applications of heat capacity data and the problems involved in obtaining accurate experimental data.

Jan 1, 1962

By L. M. Demers, D. C. Kuhn, N. El-Ayouby, C. F. Stanley

"Oxygenated metabolites of arachidonic acid (MJ are produced by the alveolar macrophage (AM) and have been shown to mediate inflammatory reactions. We therefore assessed the production of eicosanoids by AM harvested from the lungs of rats ex· posed to a bituminous coal dust for 2 wk in an inhalation chamber in order to determine if AA metabolism was altered in a manner that may promote an inflammatory response in the lung. Exposure to coal dust resulted in a 66% increase in the number of AM harvested, an increase in thromboxane A2 (TxA;i) and leukotriene 84 (LTB,j) production to 222% and 181% of control values, respectively, and a decrease in prostaglandin E2 (PGE:i) production to '62% of control values. In AM harvested from rats allowed to breath clean air for 2 wk following coal dust exposure, PGE2 production returned to control levels but TxA2 and LTB4 production remained elevated. The TxA2 synthesis inhibitor UK 38,485 reduced TxA2 production in dust-exposed AM both immediately and 2 wk following exposure. Thus, exposure of rats to coal dust significantly alters the metabolism of AA in AM, with potentially important aspects of AA metabolism remaining altered even after a 2-wk recovery period. Based on the established role of eicosanoids in inflammatory and fibrotic processes, these results suggest that the alteration of AM eicosanoid production as a result of the inhalation of coal mine dust may be an important factor in the pathophysiology of coal workers' pneumoconiosis.The authors are grateful to Joan Greenwood and Barbara Scheetz for their excellent technical assistance and to Brenda Pavone for the preparation of the manuscript. This research was supported by the U.S. Department of The Interior's Mineral Institute Program administered through the Generic Mineral Technology Center for Respirable Dust under grant 1135142.Request for reprints should be sent to Douglas C. Kuhn, Ph.D., Department of Pathology, The M.S. Hershey Medical Center, Hershey, PA 17033.INTRODUCTIONPulmonary alveolar macrophages (AM) are activated by foreign particles and microorganisms that enter the small airways (Kass et al., 1966; Herscowitz, 1985). This defensive reaction involves phagocytosis, lysosomal enzyme release, and the generation of reactive oxygen species by the AM (Snella, 1986; Rich et al., 1987). A number of agents, including phorbol esters, zymosan, adenosine diphosphate, organic hydroperoxides, and calcium ionophore, have been shown to activate the AM in vitro (Badger, 1986; Marshall and Lands, 1986; Snella, 1986). The AM response to these activators appears to be mediated in part by the oxygenated metabolites of arachidonic acid (AA) (Bertram et al., 1988; Demers et al., 1987; Mcleish et al., 1987).The AM may metabolize AA through cyclooxygenase- and lipoxygenase- catalyzed pathways to produce a variety of eicosanoids including prostaglandin (PG) E2, thromboxane (Tx) A2, leukotriene (LT) B4, LTC4, LTD4, and several hydroxyeicosatetraenoic acid derivatives (HETEs) (Willis, 1970; Camp et al., 1983; Poubelle et al., 1986). The production of these eicosanoids may enhance the. defensive ability of the challenged lung since they stimulate chemotactic cell recruitment to the site of invasion, enhance extravasation of circulating immune cells, and promote local vasodilatation. However, continued stimulation of the AM population, with the consequent production of proinflammatory eicosanoids, may ultimately enhance the disease process by contributing to chronic bronchoconstriction, fibrosis, and the persistent release of toxic oxygen species."

Jan 1, 1990