Search Documents

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Brooke County and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 191 million short tons as of January 1, 1954. Of this total, 190 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Edward L. McHugh

The appraisal of mineral resources of the Challis National Forest, Idaho, by the U.S. Bureau of Mines, was made so that the mineral resources of the forest could be appropiately considered in land use planning. Information from this study is intended to tip the U.S. Forest Service to incorporate mineral resource data into forest plans The study was done in conjunction with the U.S. Geological Survey, which released a companion report on the geology and mineral potential of the Challis National Forest in 1989. This summary report is derived from a more detailed USBM Open-File Report (MLA 6-91) that includes descriptions of mines and prospects, commodity profiles, and development cost models. Since the 1860's mines within the Challis National Forest have produced mineral commodities worth more than $590 million at current (1989) commodity prices. Identified mineral resources have a gross value of about $2 billion at current prices, including 8 strategic or critical minerals. The U.S. Bureau of Mines study identified and described 723 active and inactive mineral properties within the forest. Mineral properties with identified resources were evaluate to determine their economic significance, and an assessment was made of the feasibility of mineral development. Of the 2,516,191 acres in the Challis National Forest, about 390,000 acres were classified as having mining development interest. Commercially important mineral production, mainly of molybdenum, gold, and silver from the Challis National Forest is likely for the foreseeable future.

Jan 1, 1991

By Ben E. Lindsly

The study of "bottom-hole samples follows in natural sequence the study of samples obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1930, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs.. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, That physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing Tells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental data were obtained in the study of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at higher pressure, and later became mixed with the original undissolved gas.

Jan 1, 1933

By Maria I. De Rosa

Table 19 and figure 7 show the number of fires and fire injuries for surface metal/nonmetal mines by state during 1990-2001. Table 19 also shows the injury risk rates, employees' working hours, and lost workdays. A total of 79 fires occurred in 16 states during 1990-2001 for these mines. Forty-five of the fires caused 44 injuries and 2 fatalities (including 9 fires and 7 injuries involving contractors). The yearly average was 6.6 fires and 3.7 injuries. Sixty-five fires with 31 injuries and 2 fatalities occurred at metal mines, and 14 fires with 13 injuries occurred at nonmetal mines. The Ewhr value was 546 x 106 hr (In = 0.016), and the LWD value was 13,134. Nevada and Arizona had the most fires (19 fires, 10 injuries, and 1 fatality; and 19 fires and 11 injuries, respectively). They were followed by Minnesota (11 fires, 4 injuries, and 1 fatality) and Alaska (6 fires and 4 injuries). Of these states, Alaska had the highest injury risk rate value (In = 0.079). Table 20, partly illustrated in figure 8, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased during the second period, then decreased during most of the remaining periods. The number of fire injuries decreased during most of the periods (a small increase is seen during the last period), accompanied by a decline in employees' working hours during most of the periods (a small increase is seen during the third and fourth periods). The In values follow patterns similar to those shown by the number of fire injuries. Tables 21-26 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 9 shows the major variables related to fires for 1990-2001. Table 27 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By N. S. Dalal, V. Castranova, X. Shi, W. Wrr, V. Vallyathan

"SUMMARY Data presented here indicate that freshly fractured silica exhibits surface characteristics and biologic reactivity distinct from aged silica, and on this basis we propose that these surface features may lead to enhanced manifestations of lung Injury. Grinding of silica produces ~10"" Si and SI-O (silicon-based) radicals per gram of dust on the particulate surface which are characterized by an electron spin resonance (ESR) spectrum centered around g = 2.0015. These silicon-based radicals react with aqueous media to produce OH radicals, which are demonstrable using a DMPO spin trap. The concentration of silicon-based radicals in silica decreases with aging in air and exhibits a half-life of ~30 h, whereas its ability to generate OH radicals in aqueous solution decreases with a half-life of ~20 h. However, on storage in aqueous media, the concentration of silicon-based radicals end the dust's ability to generate OH radicals decrease significantly within a few minutes. Freshly ground silica is also more biologically reactive than aged silica, because freshly crushed silica activates a greater respiratory burst In alveolar macrophages than aged silica, i.e., storage of ground dust in air decreases silica-Induced superoxide anion secretion, hydrogen peroxide release, and NBT reduction by 25%, 68%, and 43%, respectively. Furthermore, compared to aged silica, freshly ground silica exhibits a greater cytotoxic effect on cellular membrane Integrity, i.e., a 1.5-fold increase in LDH release from macrophages, a 36-fold increase in hemolytic activity, and a three-fold increase in the ability to induce lipid peroxidation. Because acute silicosis is frequently associated with occupations in which freshly fractured crystalline silica of respirable size is generated, the present study suggests that fracture-generated silicon-based radicals may play a significant role in the pathogenesis of this disease. AM REV RESPIR DIS 1955; 133:1213-1218IntroductionOccupational exposure to crystalline silica can be associated with either chronic or acute pulmonary disease. Chronic silicosis becomes manifest 20 to 40 years after first exposure and is characterized by development of concentric hyalinized nodular lesions in the lung with the de-velopment of dyspnea over a period of several decades. Acute silicosis, on the other hand, is manifested by a rapid on-set after exposure and is characterized by the accumulation of an amorphous granular lipoprotein exudate in the airspaces and rapid development of respiratory disability within a few years (1-3).Information is growing concerning the etiology of chronic silicosis. Studies sug-gest that several mechanisms may be in-volved in the development of fibrosis. Lung injury may result from silica-induced release of lysosomal enzymes from alveolar macrophages (4, 5). In ad-dition, silica-induced activation of su-peroxide anion and hydrogen peroxide release from alveolar macrophages may result in oxidant-induced damage to lung parenchyma (6). Silica exposure can also result in the release of mediators from alveolar macrophages which enhance the proliferation of fibroblasts and the syn-thesis of collagen by these pneumocytes (7, 8)."

Jan 1, 1988

By B. D. Nash

The Bureau of Mines continued its research into the recovery of fluorine by the phosphoric acid acidulation defluorination of phosphate rock concentrates. A small process development unit with a capacity of about 10 kilo-grams of charge per hour was operated, and concentrates from both Idaho and Florida were processed. Over 80 percent of the fluorine was evolved and recovered as a dilute fluosilicic acid solution. Phosphate extraction from the concentrates always exceeded 98 percent. The fluorine was converted to a synthetic fluorspar product (3CaFa?SiOa) suitable for use as a slag conditioner in electric furnace steelmaking operations.

Jan 1, 1977

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal, (2) to upgrade marginal coals through effective preparation, and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the seventh of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Floyd County, KY., which comprises parts of the Paintsville, Prestonsburg, Harold, Hindman, and Pikeville quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all avail-able data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By R. Blickensderfer

Laboratory wear testing was conducted by the Bureau of Mines on a variety of typical wear-resistant alloys used in mining and mineral-processing equipment to establish their relative spalling and abrasion resistance. Test specimens in the form of 75-mm-diam balls were subjected to repeated impacts until they broke, spalled excessively, or received several hundred thousand impacts. Pin specimens removed from the balls were evaluated for high-load abrasive wear. The alloys in-cluded commercial forged steels, cast steels, manganese steels, and four types of white cast iron, with a range of heat treatments. The effects of hardness and microstructure on impact wear and abrasive wear are discussed. The data should help mine operators select the compositions and heat treatments that best suit service conditions.

Jan 1, 1985

By James Paone

This report shows the feasibility of predicting drillability, analytically, by using regression analysis techniques. The approach is new in diamond-drilling research. Further, the study shows that this technique may be of value to drill manufacturers and others in mathematically delineating performance characteristics of new drills in specific rock types. Another application might be the prediction of penetration speeds in extraterrestrial material based on the physical properties of the materials as samples become available. Prediction equations for penetration rates are presented for 9 rocks drilled in the laboratory and for 20 rocks drilled under field conditions. The prediction equations are based on drill operating parameters and on characteristics of the rock penetrated. No single physical property appeared consistently in the best predictor equations, and all the physical properties were found to be highly correlated with each other.

Jan 1, 1966

By Robert L. de Beauchamp

The Bureau of Mines reviewed aluminum chloride technology to determine the problems associated with its preparation from minerals, and to ascertain the best areas for research to solve these problems. Commercial AlC13 production processes are described and the ?state of the art? for the preparation of AlC13 from aluminous materials is evaluated. Areas for further research are indicated.

Jan 1, 1969

By A. J. Fejes

The purpose of this Bureau of Mines report is to provide mining industry personnel and regulatory authorities with a subsidence-reference list and annotated bibliography that will aid them in locating subsidence information and in developing their own subsidence information sources. Over 700 references are listed in the Bureau's subsidence information center bibliography; approximately 600 of these references were obtained for assessment. Of these 600 references, 167 were selected to be rated, categorized, and annotated. All literature referenced in this report was published prior to 1984. Table 1 is a cross - referenced index that classifies and rates selected references with respect to specific keywords. References are rated not on quality of content but rather on applicability to given subject areas. Appendix A is an annotated bibliography of the references listed in table 1 and provides further information of each article to aid the user in selecting articles for specific areas of subsidence technology. Appendix B is a copy of the subsidence information center bibliography.

Jan 1, 1985

As part of the United States Department of the Interior, Bureau of Mines Health and Safety Research Program, Walter C. McCrone Associates, Incorporated has examined 71 samples of airborne mine dusts using the techniques of x-ray diffraction, electron microprobe analysis and light microscopy. This report details the procedures which were used in this work and documents the results which were obtained.

Jan 1, 2011

By Ben E. Lindsly

The study of "bottom-hole' samples follow,-is in natural sequence the study of samples3 obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1530, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, what physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing wells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental rata Mere obtained in the stud of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at some higher pressure, and later became mired with the original undissolved gas.

Jan 1, 1933

By J. J. Shields

The Bureau of Mines observed two different types of longwall mining; the advancing longwall method and the retreating longwall method at seven bituminous coal mines located in five of the coal producing states. In two mines using the advancing face method, the coal faces were abandoned because of roof failures and poor production. In the other five mines using the retreating method, roof control was good as was production. The success of longwall mining depends on good roof control and good production. The use of self-advancing hydraulic roof supports, such as Westfalia, Dowty, and Wanheim props along with Westfalia coal planers and the Anderton and Eickhoff shearer-loaders have been a factor in recent successes.

Jan 1, 1967

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants. On account of extensive folding and faulting of the coal measures, mining in Washington presents many difficulties; therefore a description of the methods employed at some of the mines may be useful in planning operations in other regions, and is presented in this bulletin. The coals of Washington differ in quality, ranging from true lignites in Cowlitz County in the southern part of the State to anthracites in the Mount Baker district of Whatcom County, in the north~ rn part. Most of the output consists of subbituminous and bituminous coals, the latter including both coking and noncoking varieties. Analyses of the coals of the State and descriptions of the beds from which the samples were taken have been printed in publications of the United States Bureau of Mines.2 Details of coal beds and analyses of the coals of King, Kittitas, and Pierce Counties have also been published by the Washington Geological Survey; 3 and most of the coal beds of the State are described in some detail in a bulletin of the United States Geological Survey.4 In 1918 mining was in progress at 72 mines in the State 4a; 46 of these mines each employed more than 10 men underground. These mines were distributed as follows: Thurston County, 1; Lewis County, 7; Kittitas County, 14; King County, 16; Pierce County, 6; Skagit County, 1; and Whatcom County, 1. During that year a total of 5,847 men were employed, 4,172 underground and 1,675 on the surface. The average number of days worked in the State was 275, and the average yearly output per man was 706 tons. Coke is made only in Pierce County by four companies, which have a total of 341 beehive ovens. In 1918 they produced 93,699 tons of coke. Up to 1919 mining machines were little used in the State. In 1917 only 6.61 per cent of the coal :produced was undercut by machines. In that year 58.95 per cent of the coal was mined by hand, and 34.44 per cent was shot off the solid. The explosives used were as follows: Black powder, 36.6 per cent; dynamite, 38.l per cent; and permissible, 25.3 per cent. The State of Washington is divided naturally into two parts by the Cascade Mountains which extend north and south somewhat west of the middle of the State. The coal areas east of the range will hereafter be referred to as eastern Washington-though nearly all of it is west of the middle of the State-and that on the west side as western Washington. The geographical distribution of the coal fields is shown in Plate I. Exploration of the State has not been exhaustive enough to preclude the possibility of discovering, besides the foregoing, other districts that contain deposits of coal in commercial quantities.

Jan 1, 1924

By G. L. Neumann

The Guymard mine in Orange County, N. Y., is reported to have been discovered in 1862 and mined until 1876, producing 10,000 tons of lead and zinc ore. The property was examined by an engineer of the Bureau of Mines in 1948. Development work was done by the Bureau in April and May 1949 and March 1950. During these two periods four drill holes totaling 2,090 feet were completed. The mineralized sections of the core were sampled and assayed.

Jan 1, 1952

By G. H. Martindill

Complex chemical and physical changes occurring during carbonization result in a heterogeneous system composed of gaseous, liquid, and solid phases, whose relative proportions and chemical compositions change constantly as temperature increases. Studies in which the participating variables are isolated and controlled should be useful in formulating the mechanism of coal carbonization. The most characteristic property of a coking coal is its ability to form a plastic mass at a certain stage of the carbonization process. During this period it is believed that fluidity of the coal influences the properties of the resultant coke. This report gives results of an investigation by the Federal Bureau of Mines of the influence of the maximum fluidity attained by the charge on the physical quality of the coke or char produced. As a first approach to the problem, researchers investigated high-melting-point pitches, which are relatively simple carbonaceous materials. The plastic properties of these pitches, prepared specially for this work, varied greatly; their fluidities, as measured by the Gieseler plastometer, covered most of the fluidity range characteristic of coking coals. Blending these pitches with increasing pro-portions of fine coke progressively reduced their fluidities. Coal-pitch and coal-coke blends also were treated; their fluidities were varied by changing their blending ratios. The various blends were carbonized in a small-scale carbonizer and the resistance of the carbonized residue (char) to abrasion was determined in a small-scale tumbler test, using the Roga drum.

Jan 1, 1960

By G. St. J. Perrott, N. A. Tolch

"The testing of explosives for permissibility for use in coal mines was begun by the technologic branch of the United States Geologic Survey in February, 1909, and continued by the United States Bureau of Mines from July, 1910; this testing has been carried on from year to year as the explosives were submitted by manufacturers. As a result of these many years of testing for permissibility a large amount of data has accumulated regarding the characteristics of permissible explosives. The manufacturer expects a sample of explosive submitted for test to meet the requirements for permissibility, otherwise the sample would not be submitted. However, in spite of the careful regulation and preparation of the formulas a certain percentage of explosives fails to pass the gallery tests. It is therefore interesting to note the proportion of failures at the gallery for a given composition of explosive. The fact should be emphasized that this discussion deals with all explosives submitted for test, both those which passed the tests and those which failed to pass. Explosives that failed to pass the tests were never designated as permissible explosives and have never appeared on any list of explosives permissible for use in coal mines.The Bureau of Mines classifies permissible explosives in two ways, according to the quantity of poisonous gases produced and according to the characteristic ingredient of the explosive.4 In this paper only two types of the latter classification are considered, as follows:"

Dec 1, 1929

1. Proposals were submitted to the Western Administrative Center of the US Bureau of Mines, Denver, Colorado on 30th December, 1974 and Contract No J 0255003 was awarded, the effective date being 8th May, 1975. Dames and Moore, Denver, are associated with PD-NCB Consultants in regard to environ-mental problems, surface mining practice and legislation in US. BACKGROUND TO THE STUDY 2. Under the threefold pressures of -increased domestic fossil fuel demand -increased value of domestic energy resources -increased demand for environmental protection and safety

Jan 1, 1976

By Floyd D. Varley, C. M. K. Boldt

Toolbox training is often described as short, informal training conducted at a worksite by technically competent persons for the benefit of a work team. The key feature of toolbox training is the focus on a work team and what is important to that group in its workplace. Toolbox training conducted by peers can connect miners and establish the feeling that the hazard is a real threat to them. This feeling can bridge the gap between delivery of a safety message and behavioral changes that can prevent an accident. Toolbox training is a popular form of "maintenance" training that should not be used to teach a new skill. The 10- or 15-minute toolbox session is simply too short a time to teach or learn a new skill and test for skill development. However, the toolbox format is an excellent way to inform workers of changes in workplace rules, conditions, or hazards by bringing the discussion of change to the level of the work group and suggesting how a change will affect the way workers perform their jobs. Toolbox training should be structured to address a very specific hazard. That is, the hazard source should be identified and the effect of the hazard on the worker described. The temptation to discuss a safety subject in broad terms will result in an equally vague result. For instance, discussing "equipment guards" is inappropriate for a 15-minute training session. There simply is not enough time to cover all the hazards and their remedies. A more appropriate topic would be "placing guards on a conveyor return roller" or "hazards of cleaning a conveyor return roller." Each topic is concise enough to allow the trainer time to define a particular threat to the safety of miners and discuss ways to defend against that threat. The clearest way to a safe workplace is to identify hazards methodically and eliminate them. This cannot be done with sweeping, generalized training. Some best practices that will protect a worker from the hazard should be presented, and the hazard should be located at the specific worksite. Toolbox training is an opportunity for the work team to participate in learning and share experiences and knowledge, often through storytelling. Storytelling is an ancient form of passing along information in an entertaining way. It is entertaining because it draws the listener in with imagination and creativity. Stories told within work groups are a way for miners to exchange experiences in which they made mistakes that resulted in an accident or a near-miss and learned a valuable lesson. Thus, co-workers can learn from others without the pain or fear that accompanied the storyteller's learning path. To encourage these shared experiences, the people in the group must be comfortable with one another. Participation doesn't stop with listening to a near-miss story or informing the group of an unsafe work practice. Participation by sharing experiences, knowledge, and skills should lead toward action in changing the unsafe tool, practice, or machine (Wallerstein, 1992). This power to change is called empowerment. Empowered workers use toolbox training sessions to discuss a problem; direct their own knowledge, experience, and talents in the context of their work environment to solve the problem; and put into practice what they have learned by sharing (Baker, 1992). A worker is much more likely to implement changes they have contributed to creating than changes forced upon them. Toolbox training functions best when the group size is small (under 20) and composed of workers with similar job functions. While combining all workers on a shift or multiple shifts may be convenient, the level of participation will drop dramatically as group size increases and participants are less connected. Similarly, when the work group participants are from different job functions, keeping the materials relevant to the individual becomes more difficult. The role of management in the toolbox training system is to communicate among various groups so that all groups at a mine site are hearing the same message. In very small operations, combining work groups can be productive if the trainer can promote open discussions and lead the group to solutions that address the needs of all and not let one group or individual dominate the discussion. WHY USE NARRATIVE METHODS An effective communications tool is to use stories as a means of describing a hazard and its consequences. Historically, using stories to transfer knowledge between individuals of the same and different generations is well established. All good stories share the same elements required to communicate safety principles. Stories require a setting (the part of the workplace), a plot (the circumstances that lead to a hazard), the solution (best practices), the lesson (what can happen), and the result (what will be done to prevent the hazard) (Dennehy, 1999).

Jan 1, 2002