Search Documents

By T. H. Miller

This piper is a continuation of a series of yearly review articles started in 1925 by Thomas Varley. The development of flotation has been rapid, and better understanding of the functions o' flotation reagents has resulted in many changes in the kinds and quantities o reagents used. It is the purpose of this report to present the information in such a manner as to be of value to the milling industry as well as to the manufacturer of flotation reagents. These data have been compiled from a. survey of approximately 250 flotation plants of all classes within the United States. Many of these plants made complete reports of their operations, out others were apparently unable to supply this information in sufficient detail to meet the requirements of this investigation. Although it is realized that the data obtained in this survey are not as full as they should be to render the greatest service possible to the milling industry, it is hoped that succeeding articles will include complete information regarding milling; conditions and recoveries. As in the past, every effort has been made to conceal individual plant operations. RESULTS OF INVESTIGATION Table 1 gives the tons of ore treated by gravity and flotation methods and the concentrates produced as reported by 208 plants. The totals of 77,043,535 tons of ore and 4, 596,640 tons of concentrates from this table compare with totals of 78,973,012 tons and 4,683,972 tons respectively (furnished by the Bureau of Mines, Division of Mineral Statistics), indicating that the milling survey is about 98 per cant complete.

Jan 1, 1930

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By W. F. Hazen

This paper describing the mining practices at a 100 per cent mechanized mine working the Pittsburgh or No. 8 coal bed in eastern Ohio is one of a series being prepared by the U. S. Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The purpose of assembling this data is to place before those interested in the mining industry the methods employed and the cost data on the items involved in the winning of the coal and its removal to the railroad car at the tipple. Mining costs are governed by the mining method used, which is selected for its adaptability to local natural physical conditions such as the nature and thickness of the coal, its dip, the character of the roof and floor, and the thickness of the overlying strata.

Jan 1, 1929

By Steven R. Ruggieri

This report documents the work performed and the results obtained during the field demonstration of the Remote Sealing System at the USBM's Jenny Mine near Inez, KY in the Fall of 1978. Although various portions of the Remote Sealing System had been used on a number of prior occasions, the field demonstration at Jenny Mine marked the first use of the complete upgraded system including the use of the inert gas generating system for seal placement and the first application of the new froth foam system. The objective of the field demonstration at Jenny Mine was to demonstrate the complete system by emplacing and evaluating several complete underground seals under conditions representing those of a mine fire situation. Several critical sealing conditions were identified including: ? High entry airflow ? Standing water (1 to 2 ft) in the entry ? Flowing water (150 gal/min) ? Irregular roof ? Sealing a 4-way intersection. Four seals were successfully placed under the conditions mentioned above. The demonstration served to verify proposed techniques to handle these conditions as well as to dispel any doubts about the system's capabilities. As a result of the successful field demonstration, the Remote Sealing Equipment is now under the jurisdiction of MSHA's Mine Emergency Operation ready for a mine fire emergency.

Jan 1, 1980

Low-cost housing, like automobiles, should be appraised in the light not merely of first cost but of upkeep as well. Even more important than the number of miles the family car will go on a gallon of gasoline is the number of days the family home can be kept comfortable on a ton of fuel. A furnace tender who tossed every third shovelful of coal into the ashcan would lose his job promptly, but the effect is the same when homes continue year after year to pour out precious heat through uninsulated roofs and walls, Greater economy in household heating means even more to the national economy than to the individual, especially now that we are preparing for defense. Our fuel resources, although large, should be conserved. If less fuel is used for civilian needs, augmented requirements for defense can be met without unduly increasing the number of men needed at the coal mines and oil ells or adding new producing units that might complicate ultimate readjustment to peacetime conditions when the emergency is past and over-expansion of many industries brings new problems if unnecessary demands for transportation facilities are reduced, public carriers will be able to haul more munitions, and manpower needed for national defense will be released; and by protecting workers from health hazards in their homes additional man-hours of productive effort will be gained. Moreover, reducing the running expenses of houses by proper heat insulation helps home owners to maintain payments on property, and by minimizing foreclosures helps to stabilize the financial structure of the country. In short, here is a situation where the interests of the individual and the Nation are identical and the greatest good for the greatest number is obtained without sacrifice to anyone.

Jan 1, 1941

By A. J. Barry

Recent developments in mechanizing longwall it mining in Europe have aroused considerable interest among American coal-mine operators because this method provides an opportunity to improve safety, production, efficiency, and recovery. The success of longwall mining in Europe has depended to a large degree on development of effective roof-control systems. One of the major contributing factors in designing these systems is development off improved supports, which combine high load-bearing capacities with controlled yield characteristics, to use in the face areas. Other factors that relate to successful longwall mining involve knowledge of the structural properties of the strata above end below the coal bed being mined, movements of these strata induced by mining, and effects of the strata movements on the strata itself, as well as on the support system used. Extensive studies of the above factors relating to long-wall mining have been made in coal-mining countries abroad, and corresponding studies (1, 2, 3, 4, 5)3/ of room-and-pillar operations have been made in this country. Although descriptions and results of experiments of mechanized longwall operations in the United States have been published (6, 7, 8), this is the first instrumented study of roof behavior on a longwall operation. In view of the possible widespread application of this method of mining to American coal mines, where underground mining conditions are different from those found in European mines, an investigation was conducted at a mechanized longwall operation inn the Lancashire No. 15 mine, Barnes & Tucker Co., Cambric County, Bakerton, Pa., to study the factors that affect roof control. This report describes this investigation and discusses the results. ACKNOWLEDGMENTS This investigation was made under a cooperative agreement between the Bureau of Mines and the Barnes & Tucker Co., Barnesboro, Pa., end was conducted in the Lancashire No. 15 mine located at Bakerton, Cambria County, Pa. The authors acknowledge the cooperation given by Richard Z. Todhunter, Sr., president, Richard T. Todhunter, Jr., general manager, and other mine officials and employees of the Barnes & Tucker Co. Mr. Edward Thomas, chief, Roof Control Section, Bureau of Mines, Washington, D. C., and Dr. Leonard Obert, chief, Applied Physics Branch. College Park, Md., collaborated in the planning and promulgation of the program investigation.

Jan 1, 1954

By E. L. Burwell

Preliminary results of an in situ oil shale retorting experiment conducted by the Bureau of Mines in a shallow bed of Green River oil shale at Rock Springs, Sweetwater County, Wyo., are described. Eleven wells were drilled into a 20-ft-thick section of the shale lying between 68 and 88 It deep, and attempts were made to connect the wells through the shale with a fracture system created by application of high-voltage electricity (electro-linking), hydraulic fracturing, and explosive fracturing. Ignition of the shale through the central well was easily achieved with a propane burner, and shale oil began to collect in three wells within 3 hours. Propane injection was discontinued after 7 days, and combustion continues, although attempts to control the direction of the combustion front have been unsuccessful. Production rates as high as 4 ½ barrels of nil per day have been recorded, but too little is known about underground conditions to permit an estimate of recovery efficiency at this time.

Jan 1, 1969

By D. L. Paulson

Electric furnace smelting of blister copper directly from copper precipitates (cement copper) was investigated by the Federal Bureau of Mines. Copper concentrations in five different lots of cement copper in the investigation ranged from 62.5 to 82.5 wt-pct. Laboratory-scale smelting tests were made in a 50-kva electric-arc furnace to establish the reductant and flux requirements. Best recoveries were realized by adding 60 pct of the carbon required to combine with the contained oxygen in the cement copper. Operating parameters established during the laboratory-scale smelting tests were used successfully in smelting 20 tons of cement copper during 12 pilot-scale tests in an 800-kva electric-arc furnace. Over 98 pct of the contained copper was recovered as blister-grade metal. The projected energy consumption for a commercial-size furnace was 380 kwhr per ton of cold charge.

Jan 1, 1978

By Frank G. Horino

A rock mechanics program (composed of laboratory and field tests) was initiated by the Bureau of Mines in an effort to determine the causes of pillar instability at the Fletcher mine, near Bunker, Mo. Compressive strength, Young's modulus, shear strength, and the angle and coefficient of internal friction were determined on drill cores obtained from 16 different locations in the mine. Results of the laboratory tests showed that highly mineralized zones and brecciated zones in pillars could significantly affect pillar strengths and stability in locations where extraction ratios exceeded the normal design ratio of approximately 78%. High-angle fractures that were present in Some locations also may have contributed to pillar deterioration. In the field tests, in situ stress determinations were made in one pillar to establish the pillar-loading conditions and to evaluate the stability of the pillar. Continued monitoring of stresses in the pillar showed a gradual decrease in compressive stress, indicating that the pillar was probably in the postfailure state. A second stress determination was made in a vertical hole in the underlying igneous rock that was exposed on one section of the mine. Horizontal stresses were compressive and larger than would be expected from gravity loading.

Jan 1, 1978

By Rolland L. Blake

Petrographic and mineralogical studies were made on unoxidized samples from the Cuyuna and Mesabi districts to study occurrence and properties of the iron phyllosilicate minerals . Examination of 96 thin sections from the thinbedded facies of the main iron - formation of the Cuyuna district indicates that the most abundant minerals are Mn - Mg - siderite , stilpnome lane , and minnesotaite . Reconstitution and recrystallization of minerals has occurred along certain beds , and textures indicate that some minnesotaite apparently formed at expense of stilpnomelane . Three samples of stilpnome lane and one of minnesotaite were concentrated from fracture - fillings within iron- formation . Results of chemical , optical , spectrographic , X- ray diffraction , and differential thermal analyses on these samples are reported . The detection of ammonia in stilpnome lane samples is the first such occurrence reported , and its significance is discussed . New mineral data are presented on greenalite and probable septechamosite from the Mesabi district .

Jan 1, 1964

This report, the fourth in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more effectively extract and process mineral products. Environmental considerations, health and safety standards, price controls, inflation, material shortages, and more dependence on foreign imports were problems faced by the minerals industry. Although productivity increased for most mineral commodities, the annual rate of increase has slowed in recent years, indicating a maturing technological situation. Growing concern for energy resulted in increased interest and research in alternative fuel sources. The primary concerns of metallurgists were pollution control and improved efficiency and performance of metallurgical processes, especially for reduction of energy consumption.

Jan 1, 1974

By A. W. BELDEN

Among the investigations that the Bureau of Mines is conducting witha view to increasing efficiency in the utilization of fuels belonging to or for the use of the Government is an investigation of the processesthat take place in a foundry cupola during a melt. Some observations on the results of cupola tests of cokes at the Government fuel-testing plant in St. Louis, Mo., the coke being fromcoal from many coal fields of the United States, have been stated in a previous bulletin.s Especial attention was given to the meltinglosses that resulted from the use of different grades of coke, light and porous or heavy and dense. These losses amounted in one instance to 52.5 per cent of the iron charged and showed, in convincing manner, the need of exact information in regard to conditions in the fuelbed of the cupola.b Melting losses of iron have been fully appreciated but little under-- stood. The fact that these losses were possible with either light or heavy coke led to the belief that by using small charges 80 placed that. melting would take place in that zone of the cupola where the highest heat and the smallest percentage of oxygen prevailed and by confiningall melting to this zone these losses would be eliminated and the economical use of practically any coke produced for metallurgical purposes would become possible. This widening of the field from whichcoke might be drawn for foundry purposes would serve to place the foundryman in an independent position as regards his source of supply, and would tend to conserve the better grades of coking coals, which are being rapidly exhausted, by making the poorer grades available for mixing with them. In order to investigate conditions within a cupola, the Bureau of Mines as a first step decided to install a commercial cupola, to sample the gases during their travel from the tuy~res upward, and to determine the temperature of the fuel bed.

Jan 1, 1913

By T. E. Hill

The Bureau of Mines investigated the possibility of physically separating Missouri and Minnesota granites into commercially usable fractions of feldspar, quartz, and mica by mineral dressing techniques. The probability of r covering a feldspar fraction from raw granite suitable for commercial uses was developed through correlation of the iron oxide content by extensive petrographic studies. This probability evaluation also included Wisconsin granites and a high-feldspar iron ore concentration tailing from Missouri. Laboratory recoveries of feldspar and quartz were on the order of 80 percent. Mineral content of each fraction was generally over 95 percent, indicating excellent response to separatory techniques, Acid leaching of feldspar and quartz concentrates to remove iron oxide improved the grades chemically; however, occluded iron oxide particles in the leached products prevented attaining top grades of feldspar. Mica was removed as scrap grade at low recoveries. Each concentrate conformed to some category of commercial feldspar, quartz, or mica.

Jan 1, 1969

By R. G. Knickerbocker, C. T. Baroch, A. W. HACKWOOD

The difficulties inherent in the production of alumina by the formation of potassium alum and its subsequent thermal dehydration and decomposition have been overcome , to a large extent , in a process developed at the Boulder City Station of the Bureau of Mines . This process is applicable to the reserves of alunite known to occur in several Western States and , possibly , to certain clay and low-grade bauxite deposits known to exist in this country . The operations sequence of the process is shown in the flow sheet (fig . 1) . Only those steps included within the heavy line are considered in this report . Four different procedures for dehydration of alum were investigated ; ( 1 ) Spray drying , ( 2 ) rotary - kiln drying , ( 3 ) dry grinding in a thermal ball mill , and ( 4 ) dehydration in the vertical- column flash dehydrator . Based upon fuel requirements and other practical considerations , the vertical- column dehydrator , or some modification of its operating principle , offers the botter possibility for commercial use .

Feb 1, 1946

By W. D. Dietzman

This Bureau of Mines report presents a continuation of statistics pertaining to distribution of petroleum reservoirs (or fields), wells, and production by depth and producing rate classification in the United States. These statistics show the change that has occurred since results of a similar study were published by the Bureau of Mines in 1967. Data are presented in tabular form by State for the 18 principal oil-producing States and by subdivision for the two largest oil-producing States, Texas and Louisiana. Tabular summations and graphical illustrations are presented for the Nation. The data are classified by 4-barrel-of-oil-per-day rate increments up to 36 barrels and one increment of greater than 36 barrels of oil per day and by 2,000-foot depth increments up to 8,000 feet and one depth increment of greater than 8,000 feet. The overall average producing rates for States and the Nation have been published for many years, and although such rates are useful, they are very general descriptions of producibility. A breakdown of production, wells, and reservoirs by various depths and rates and by State or by State subdivision provides a more detailed description of producibility.

Jan 1, 1975

By C. Thomas Hillman

This Bureau of Mines report describes an investigation of factors influencing economic viability of a proposed system to mine and process manganese nodules. The system consists of hydraulic dredging and ammonia leach processing designed to recover three metals: nickel, copper, and cobalt. A ferromanganese recovery plant is a considered option. Annual capacity is 3 million dry metric tons (t) nodules. Aftertax rates of return (ROR's) of only 7.38 and 6.63 pct are predicted for three-and four-metal base scenarios, respectively. Sensitivity analyses indicate that variations in commodity prices, metal recoveries, and deposit grades produce similar incremental changes in ROR. Estimated cumulative effects of price variations are greatest. While three-metal operations generally yield higher predicted returns, potential increases in manganese price and process recovery could make four-metal operations most profitable. Maximum variations in both capital costs and three-metal operating costs result in ROR changes of about 25 pct. In contrast, four-metal ROR's exhibit variations to 70 pct. Even so only a best case analysis, utilizing favorable variations in all categories tested, generated ROR's approaching a level thought necessary to trigger company interest. Consequently, it is concluded that nodule mining will not take place in the foreseeable future without significant financial incentives.

Jan 1, 1985

By A. M. Gaudin

A study of the consumption of reagents used in flotation gives useful data as to the market which employment of the flotation process creates for the manufacturers of the necessary chemicals and oils, and furnishes a useful clue to the trends in flotation practice influencing the choice of reagents used and the' extent to which new reagents are displacing less suitable older reagents. In the present investigation an attempt has been made to cover both of these phases of the consumption of reagents in flotation. Unfortunately, however, the data collected in tie various districts have not been equally informative; some operators have reported very completely both the consumption of reagents and the metallurgical results obtained therewith, while others were apparently unable to supply these figures in sufficient detail to meet the requirements of this investigation. RESULTS OF INVESTIGATION Table 1 gives the tonnage of ore treated by flotation, as reported. This table shows that flotation has been most largely used in the concentration of copper ores, next in complex lead-zinc ores, followed by lead ores, zinc ores, miscellaneous ores, and copper-iron ores.

Jan 1, 1929

By H. E. Powell

A solvent extraction procedure was developed on a laboratory scale for recovering trisodium phosphate, zinc, and iron from waste phosphate sludge as separate products. The sludge was dissolved in hydrochloric acid, and iron was extracted as ferric chloride by isopropyl ether. Zinc was extracted by di-2-ethylhexyl phosphoric acid in kerosine. The efficiencies of the one-and two-stage extractions ranged from 98 to nearly 100 percent. Trisodium phosphate was recovered by crystallization from the raffinate. The value of two marketable products is considerably more than than the costs of the major reagent. The process was developed to permit recycling of values in this waste and to consequently reduce stream pollution from this source.

Jan 1, 1972

By James J. Dowd

During and immediately following World War II, the heavy demands for steel required the mining of unusually large quantities of coal for the manufacture of metallurgical coke. The largest demand for metallurgical coke is in the Appalachian region, which comprises central and western Pennsylvania, Maryland, West Virginia, Virginia, eastern Kentucky, Tennessee, and Alabama. This demand is satisfied by coke made from coals within the region; consequently, the reserves of coking coal in this region are being depleted more rapidly than reserves in other coal-producing regions. The supply A' high-quality coking coal during the war was inadequate, and some coke were forced to use inferior coals. The coke produced from these inferior coals adversely affected the rate of production. Another national emergency probably would produce a similar condition, and in the interest of -national security, the Munitions Board of the National Military Establishment requested the Bureau of Mines to evaluate the reserves of coals suitable for the manufacture of metallurgical coke. All bituminous coals in the Appalachian region are coking, and as the coal that produces the better metallurgical coke become depleted, other coal previously considered inferior will be used. The general trend is toward the use of lower-quality coals for metallurgical purposes.

Jan 1, 1950

By J. C. Cawley, G. T. Homce, M. R. Yenchek, H. K. Sacks

As in many other industries, such as construction and agriculture, overhead electric power lines are a serious hazard at mining and mining-related operations. Even when excluding injuries that occur during electrical maintenance work, over one fourth of electrical fatalities in the mining industry are due to accidental overhead line contacts, and for each fatality nearly two serious non-fatal injuries occur due to such contacts. In incidents involving high-reaching mobile equipment, many of the victims touched the equipment after the fact, unaware that the machine frame had become energized by the line contact. MSHA data for accidents involving overhead power line contacts in the mining industry between 1980 and 1997 reveal that in 57% of the cases personnel were unaware of the accidental line contact until after one or more workers touched the equipment or a hoisted load and were injured. The situation is similar in the construction industry, where according to the National Institute for Occupational Safety and Health (NIOSH) data at least 20% of such victims are unaware of the line contact. This suggests that a device that alerts workers when a power line has been contacted could help prevent many of these injuries. Such a device would not prevent power line contacts, yet if widely employed could yield a significant reduction in the number of resulting injuries. Researchers at the NIOSH Pittsburgh Research Laboratory are attempting to develop such a device. The approach being investigated is based on measuring electric current flow to ground through a machine during a line contact. The specific technique being tested involves the diversion of some part of this current through a shunt cable mounted on board the machine, to provide a point at which to install a current sensor. Experiments thus far indicate that this approach is feasible. Ongoing research is better defining electric current flow through mobile equipment, refining techniques for measuring this current, and identifying factors that could limit the effectiveness of the proposed alarm.