Search Documents

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibration limits for buildings with respect to ground vibrations from pile driving published in international standards are reviewed. At first, relevant vibration parameters are defined and the evaluation of vibration records is described. The sensitivity of structures to different vibration parameters (displacement, velocity and acceleration) is discussed. Most vibration standards relate to blasting activities, the dynamic characteristics of which can be significantly different to those from construction activities and in particular, pile driving. Several vibration standards are reviewed. The Swedish vibration standard is described in detail, as it is the only one accounting for several important factors, such as ground conditions, building material, and type of building foundation. Many standards limit the guidance to values based on the dominant vibration frequency and a wide scatter of frequency-dependent vibration limits exists. It is difficult to compare limiting values of ground vibrations proposed in different standards.1. INTRODUCTIONFor poor ground conditions, placing structures on piles is the most common foundation solution, while sheet piles are widely used to support deep excavations. Piles and sheet piles must often be installed in the close vicinity to buildings, structures or installations in the ground, which can be affected by ground movements and vibrations, (Massarsch and Fellenius, 2014). In many areas, environmental concerns with respect to noise and ground vibrations can restrict or even prohibit driving of piles or sheet piles or reduce the efficiency of installation. The design engineer must prescribe – often at an early stage of a project — the permissible levels of ground vibrations in order to minimize the potential risk of building damage. When seeking guidance from the literature, little or practically no applicable information can be found on how to assess permissible levels of ground vibrations."

Jan 1, 2014

By J. Matos e Silva

The paper refers two examples of structures located in seismic areas (Cases 1 and 2). The first one (Case 1) is the Torroal Bridge, located about 100 Km South of Lisbon, in the road Troia-Grandola. The horizontal loads due to the seismic actions were mainly carried by an anchor curtain connected, to the abutments, by reinforced concrete struts-ties. For the some purpose diaphragm walls were also placed under the pile caps of the column foundations. The second one (Case 2) refers to a building located about 50 Km South of Lisbon, at Sesimbra, near a cliff. To reduce the horizontal displacements of the structure due to seismic actions, in order to prevent the endangering of the cliff stability, an anchor curtain was adopted and connected, to the structure, by prestressed anchors.

Jan 1, 1996

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

By Clyde N. Baker

The paper describes procedures used to predict the settlement performance of drilled shafts constructed under slurry through water bearing deposits to a dense bearing strata, considering both side resistance and end bearing. A full scale instrumented drilled shaft load test on a Jersey City, New Jersey highrise project is used as a case history to compare with prediction.

Jan 1, 1991

By Wu Jie Mei, Li Yao Liang, Franz-Werner Gerressen, Arthur Bi

Diaphragm walls (D-walls) are known as underground structural elements commonly used for retention systems and permanent foundation elements. In addition, they are also quite often used as deep groundwater barriers, called Cut-Off-Walls (COW). Shanghai ranks third among the most densely populated metropolises in the world. In 1990, only eight million people lived there. Today, Shanghai has about25 million inhabitants. The increasing demand to accommodate the infrastructure of growing megacities like Shanghai pushes the required depth for subway, sewage and foundation projects to the limit. Future projects will demand excavation depths of more than 100 m (328 ft) on a regular basis. Already carried out reference projects will be described and a general outlook for upcoming projects will be given. The paper also explains the installation process in general focusing on the use of trench cutter technology. INTRODUCTION D- walls are known as underground structural elements, commonly used as retention systems for excavation pits and shafts as well as permanent foundation walls or elements. It is anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions and with increasing depth. The trench cutter is the most important tool for performing this work. The hydraulic grab, a well-known and valuable excavation tool for d-walls reaches its limits in terms of depth and when cutting rock. Therefore the trench cutter technology will be in the focus of this paper. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around the horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter wheels is continuously broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the suction box of the pump? A centrifugal pump located right above the cutter wheels conveys the slurry via a hose system up to a desanding plant. There the slurry loaded with soil and rock particles is cleaned and returned into the trench.

Jan 1, 2018

By L. D. Johnson

12 groups of 12 precast prestressed (PCPS) piles were driven in the lagoon of Kwajalein Island to support a dry dock. Pre-construction investigation of the calcareous coral sands and static pile loeid tests were performed to determine if the 7.9 by 7.9 cm (20 by 20 inches) by 26 m (85 ft) long PCPS piles embedded to a depth of 16 m (53 ft) would adequately support the dry dock. Driving records for production piles indicated that the blowcounts of the piles at the fincil embedment depth became substantially less than expected as piles wssre driven further toward the lagoon end of the dry dock and decreased to as low as 2 blows/ft. A supplemental investigation that included a static load test on a production pile, the driving of an indicator pile, and restrikes indicated that the pile foundation has adequate bearing capacity. The observed bearing capacity appears to be effected by several mechanisms including breakdown of cementation between sand particles, densification of the sands during driving, and dissipation of excess pore pressures and recementation after driving.

Jan 1, 1993

By I. H. Wong

The large diameter caisson foundations and their construction methods for three 50 to 60 storey high buildings in Singapore are described. The caissons are 5 m to 8 m in diameter and 40 m to 100 m deep, excavated either by hand or mechanised excavators or by drilling and blasting. Performance of the 50 storey DBS Building is described.

Jan 1, 2010

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By EFFC/DFI Concrete Task Group

Concrete technology continues to advance rapidly and modern mixes with five components – cement, additions, aggregates, (chemical) admixtures and water – often have characteristics which differ significantly from the older three component mixes – cement, aggregates and water. Recent trends have favoured higher strength classes and lower water/cement ratios, resulting in greater dependence on admixtures to compensate for reduced workability and to meet the (often competing) demands for workability in the fresh state and setting time. The application of testing methods which reflect the true rheological properties of the concrete has not developed at the same rate as the mixes themselves and it is still not uncommon for the slump or flow table test to be used as the only acceptance test for fresh concrete.A joint review of problems in bored piles (drilled shafts) and diaphragm walls cast using tremie methods by both the European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute in the United States (DFI) identified a common issue. The review determined that many of the problems were caused by (or in part due to) the use of inadequate concrete mixes with inadequate workability, or insufficient stability or robustness of the mixes. It further identified the primary causes as inadequate concrete specifications and inadequate testing procedures. The consequences of these problems are often significant and it has been recognised that spending more time and money on getting the concrete right is the most cost effective approach.A joint Concrete Task Group was set up by EFFC and DFI in 2014 to look at this issue and this guide is the output from that Task Group. A research and development project, funded by the Sponsors of this guide, is being carried out by the Technical University of Munich in conjunction with the Missouri University of Science and Technology. This project includes desk studies, laboratory testing, and onsite testing at worksites in Europe and the US. The research work will be completed during 2016.

Jan 1, 2016

By Xiong Houjin

In the excavation works of some deep foundation pits within the boundaries of Guang­dong Province of China, though some measures, such as steel sheet piles, diaphragm walls, etc. were taken to protect the walls, the construction of the excavation works was often accompanied by damage of buildings and public facilities, surface settelment. sand boil and collapse of piles. When these happened, only chemical grouting could be used as the most efficient measure for rushing to deal with or rescue the emergencies. Besides, the application of chemical grouting protection wall technique also palys a very important role under the geologic conditions of the coastal areas of Guangdong Province, when applied in the mucky oystershell layer wealthy in water and the deep mud layer, it can not only achieve good results, but also reduce the cost significantly. In this paper, we discuss the water-tight and earth retaining functions of chemical grouting protection wall in weak formation, and introduce the applicable ranges of chemical grouting protection wall in the excavation of deep foundation pits. Some technological principles and design considerations of the construction of chemical grouting protection wall are presented. Different types of protection wall are also introduced.

Jan 1, 1991

By Richard A. Forth

During the construction of the Island Line (ISL) in Hong Kong between 1982 and 1986 piled foundations of a building were encountered in a tunnel drive. As the tunnel alignment could not be changed work was temporarily suspended whilst grouting took place beneath the pile cap. The tips of the piles were then cut off. The normal precast concrete lining segments were replaced by the "stiffer" spheroidal graphite iron segments and tunnelling resumed. Settlement of the building was found to be under 10 mm due to the tunnel drive and no damage was reported to the building.

Jan 1, 2002

By Andrew Peterson

The Maine Department of Transportation offered this challenging design-build project for a new, 12-span, bridge over the Kennebec River in Bath, Maine. This structure would be built to replace the existing Carlton Bridge connecting the village of Bath, Maine to neighboring Woolwich, Maine. The design build team of Flatiron Structures, Inc., and Figg Engineers, Inc., elected to design and build a segmental concrete bridge. Site conditions dictated that this bridge would be supported primarily on deep foundations. Case Foundation Company joined the project team in the winter of 1997 to install twenty-two, eight foot diameter drilled shafts. The drilled shafts were designed with 8' diameter, permanently cased shaft sections and 7.5' diameter rock sockets. Shaft lengths ranged from 20' long near the river's edge to 100' deep in the middle of the river. Rock socket lengths ranged from 12' to 30' deep. Two Osterberg Cell load tests were conducted on production drilled shafts. Figg Engineers utilized the results of the load tests to "fine-tune" the rock socket design during construction of the drilled shafts. Construction of the drilled shafts proved to be very challenging and called on every member of the design-build team to work together throughout the project. One of the most challenging aspects of this project was in the installation of the 8' diameter permanent casing and drilling of the rock sockets. Early in the project, it became apparent that the top of bedrock was broken and unstable. This condition limited the advancement of the permanent casing and the affect of a "seal" at the top of rock socket. As a result, as the rock socket was advanced, loose material spilled into the hole and stopped progress of the socket. In order to resolve this problem, the design-build team developed a redesigned drilled shaft which included the installation of a steel sleeve to seal off the unstable rock formation. Following installation of the sleeve, the rock socket diameter was reduced to 7' diameter and advanced additional length to achieve required design capacity. All drilled shafts were installed with equipment supported on floating barges. Water access, along with the long shaft lengths and very hard bedrock required the use of cranes and drilling equipment that far exceeded the requirements of typical drilled shaft projects. This paper will discuss the relationship between design, construction, and equipment utilization on this challenging design-build project. [ ]

Jan 1, 1999

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By S. K. V. Avasarala

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading tests and installation of over 3,300 prestressed concrete piles for a building complex consisting of 12, 5- and 6-story over parking buildings. The project was recently completed in three-phases over a span of 4 years. The subsoil conditions were explored by performing 25, Standard Penetration Test (SPT) borings throughout the site. Various types of driven pile foundations were considered and following an evaluation of high structural loads and site-specific constraints such as variable depth of bearing layer of Florida limestone and quality of clay and limestone layers, a prestressed concrete pile support system was selected as the most economical and effective foundation approach. The building foundations were designed for a pile capacity of 353 kN (40 tons) in compression, 45 kN (5 tons) in lateral capacity for a deflection of 0.64 cm (0.25 in.), and 133 kN (15 tons) in uplift capacity. The axial and lateral allowable pile capacity and lengths were predicted using SPT91 and LPILE computer programs, which are generally used in Florida. The validation of these capacities was derived from 144 probe piles and performance of 12 pile loading tests on selected probe piles. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the loading tests on probe piles. This information was effectively utilized as part of the overall quality control program to install a total of 4,186 prestressed concrete piles (including 144 probe piles) in different building areas across the project site to depths ranging from 8 to 21 m (25 to 90 ft) below existing ground elevation as part of foundation support system. This engineered, monitored, and tested foundation solution provided an effective and satisfactory basis for completion and approval of the foundation work for this 12, 5- and 6-story over parking building complex. A recent reconnaissance has indicated that all the building foundations are performing satisfactorily.

Jan 1, 1995

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By S. Kanai

Nodular piles is to be piles provided with several nodular projections along the pile shaft, as shown in Fig. 1. Nodular piles are usually installed through either driving method with hammer or preboring method. This paper presents that the bearing capacity installed through each method is considerably higher than that of cylindrical pile without nodules. This paper also proposes the statistically analyzed unique formulae of the bearing capacity of nodular piles.

Jan 1, 1989

By Donald R. McMahon

This paper presents a unique case history that documents the use of a braced secant pile wall to underpin a heavily loaded footing inside of a manufacturing plant. Construction of a pit for a new manufacturing process directly next to the footing necessitated the underpinning. The footing supports an overhead crane that needed to remain operational throughout construction of the pit and therefore, settlement of the footing could not be tolerated. The base of the footing was about 7.7 feet above the base of the 17-foot deep excavation. The footing bears on a silty clay deposit that grades from a stiff consistency beneath the footing to a soft/medium consistency near the base of the pit excavation. This paper describes the design and construction of the secant pile wall and bracing to control wall deformations, ground movements and settlement of the footing. The footing was monitored for settlement throughout construction of the pit and no measurable movement was observed.

Jan 1, 2006

By Luo Yang

It has been known that after initial pile driving, pile capacity gain over time (set-up) could constitute a significant portion of the total pile capacity. In the past, there has been very little guidance for incorporating pile set-up capacity in design. This may be due to large uncertainties involved in predicting the pile set-up. A comprehensive statistical database is developed to describe the increase of pile axial capacity with time, known as set-up, when piles are driven into sand. Based on the collected pile testing data, pile set-up is significant and continues to develop for a long time after pile installation. The statistical database shows that a lognormal distribution can be used to describe the probabilistic characteristics of the predicted set-up capacity using Skov and Denver?s equation. The main objective of this paper is to incorporate the set-up effect into a reliability-based Load and Resistance Factor Design (LRFD) of driven piles in sand. A First Order Reliability Method (FORM) is used to derive separate resistance factors that would account for different degrees of uncertainties associated with the measured short-term capacity and the predicted set-up capacity from the proposed semi-empirical equations. The incorporation of set-up effects in the LRFD helps improve the prediction of the total capacity of driven piles, resulting in more economical design. A practical design procedure within LRFD framework to incorporate the pile set-up effect is outlined at the end of the paper.

Jan 1, 2006

By Thomas C. Anderson

Thirty-four retaining walls are part of the $46 million upgrade of a 1942 depressed highway in Highland Park, Michigan near Detroit. This project will close a missing link between two newer roadways, I-75 and the John Lodge Freeway. The existing 75 ft. wide, six lane Davison Freeway is being replaced by a eight to ten lane, 200 ft. wide depressed highway in a limited right of way. The highway will be 20-25 ft. deep and 1.5 miles long. A design/build decision by the Michigan DOT saved about 37% of the engineers estimated cost of $19 million for the walls. The successful pre-qualified specialty contractor utilized an innovative solution for the walls consisting of tiedback/cantilevered walls on the north side and mechanically stabilized earth walls on the south side. All of the walls have an identical cast-in-place architectural facing.

Jan 1, 1999

By Lin Daoyi

In this paper, we have adopted the high pressure jet-grouting curtains to seal the sea-water, and to consolidate the wall of the well for deep foundation diteh, make a pladge of building and construction of deep foundation was primarily on progress without water. This paper, we have been given a test for pumping water under mainly the circumtances of sealing condition and to report in advance the capacity of seawater seeping into the gam curtains in the process of building and construction of deep foundation.

Jan 1, 1991