Search Documents

By Samuel J. Kosa

The Monotube is a uniformly tapered high-strength steel shell pile manufactured for friction pile applications. The Monotube pile was developed in the early 1920's in Canton, Ohio. Its first commercial installation was an Ohio railroad trestle in 1926. The Monotube has been manufactured in the same Canton plant since its inception. The Monotube is produced in four diameters, 12, 14, 16 and 18 inches, with U. S. Standard Gage wall thicknesses of 9, 7, 5 and 3. The uniformly tapered Monotube section can be manufactured in one of three rates of taper.

Jan 1, 1993

By Kanchan K. Sen

The North Shore Connector (NSC) project will extend the Allegheny County Port Authority?s Light Rail Transit System from downtown Pittsburgh below the Allegheny River to the North Shore via twin bore tunnels. Jet grouting, diaphragm walls, and soil mixing were selected as cost-effective technically viable ground improvement and support of excavation techniques. Jet grouting was specified to provide break-out (egress) and break-in (ingress) block sections at the tunnel boring machine (TBM) launching and receiving pits. Jet grout treatment was also used adjacent to buildings with shallow foundations and below retaining walls along the tunnel alignment. A new method for measuring jet grout column diameter based on electrical resistivity was employed on the project. New equipment was introduced in the U.S for constructing soil mix temporary support of excavation using a soil-mix technique termed Cutter Soil Mixing (CSM) due to the use of two vertical cutting wheels that have evolved from diaphragm wall trench cutter technology. The system allows for continuous water tight soil mix panel construction including steel beams. This paper highlights some applications of jet grouting and various support of excavation systems (e.g. slurry walls, cement bentonite walls and CSM walls), including new innovative techniques (e.g. Cyljet and CSM) used under the constraints of an urban environment.

Jan 1, 2010

By Juan J. Campo

The Freeport-McMoRan Main Pass Mine development in the Gulf of Mexico is a complex designed to extract up to 67 million long tons of sulphur over a 40 year period. The initial development includes 15 platforms and 13 bridges located in water depths ranging from 208 to 214 feet, approximately 15 miles east of the Mississippi River Delta. Three additional platforms were designed and installed for the oil and gas development in the complex. Over 110, 000 short tons of steel were required to fabricate the structures. As the sulphur is extracted significant subsidence is predicted over a major portion of complex in the shape of a very large bowl. Vertical elevations are predicted to change as much as 65 feet. Horizontal movements and mudline slope changes cause adjacent platform decks to move as much as 30 feet relative to each other. Differential soil movement is predicted between piling of individual platforms causing the piling to spread, resulting in significant lateral loading on the piling. Relative vertical soil movements are predicted along the lengths of the piles which causes "up drag" or "down drag" forces on individual piles. This paper addresses the design of the piling for the structures in the complex. Design criteria will be discussed explaining how the more traditional offshore environmental and gravity loadings were combined with the unique loading caused by subsidence. Design and analysis procedures will be explained and analysis results presented. These results include the incorporation of 100 ksi steel in thicknesses up to 5 inches in some of the tubular piles. Comparisons will be made between conventional offshore structures and these structures designed to accommodate the subsidence.

Jan 1, 1992

By Yukihiro Ishihara, Nanase Ogawa, Ming Lei

"Abstract In the Press-in Method, a static jacking force is used to install a prefabricated pile, while a reaction force is gained from previously installed piles. This piling technique has solved problems in urban piling construction such as noise and vibration associated with the piling work, restricted construction conditions due to the existing structures, and so on, since its emergence in 1975. Its applicability to hard ground conditions has been improved, with the development of press-in machines that involve augering or rotation. Besides, information such as time, penetration depth, jacking force and rotational (or augering) torque in piling work are automatically obtained. The concept of PPT, Pile Penetration Test, has been developed by the authors, to apply the obtained information to the processes of construction planning or foundation design. This paper highlights the technique to estimate SPT N value from data acquired in standard press-in (press-in without any auxiliary methods), press-in with augering and rotary press-in. The technique will be helpful in assuring the adequate embedment depth, re-selecting the adequate press-in machine or auxiliary method, and re-pricing the project objectively, particularly when a contractor encounters unexpected ground conditions.INTRODUCTIONThe Press-in Method is one of the piling techniques that use a static jacking load to install piles. It mitigates environmental problems of noise and vibration that have been associated with other conventional piling techniques.It is also featured by its spatial efficiency; since a ‘press-in’ piling machine gains a reaction force from the previously installed piles, there is no need of bulky weights that will occupy a large space. This feature is emphasized in the piling system in Figure 1, where a press-in machine and its related devices are all positioned and ‘walk’ on top of the pile wall.Its applicability to hard grounds has significantly been improved, with some newly developed piling machines that involve augering or that install tubular piles with teeth on the base by applying axial load and rotational torque at the same time."

Jan 1, 2014

By Aminul Islam, Vinay M. Kumar

"About 100 Hectares of land reclamation over the very soft to soft marine clay at Uran Creek in Maharashtra is planned. The depth of marine clay varies from 10m to 24m as observed from the geotechnical investigation. The marine clay was treated with Pre-fabricated Vertical Drains (PVD’s) installed from the elevation of +5.5mCD (chart Datum) and preload/placement of surcharge. A Settlement of soft soil mud under the reclamation was monitored using magnetic extensometer (M) and ground settlement maker (S2). These instruments are installed after constructing working platform at around +5.5m CD. Based on the field instrumentation data, the consolidation parameters were adjusted to match the theoretical and actual settlement plot. The author called this approach as “Back analysis method”. The objective of this paper is to present a case study of instrumented preloading treatment for a thick marine clay deposit. The degree of consolidation in clay strata was determined from magnetic extensometer and ground settlement marker data. Authors also determined degree of consolidation as Asaoka method, Hyperbolic method and Back analysis method and compared the results.INTRODUCTIONExpansion of Container terminal with port buildings, rail container depot, roads and utility buildings at Jawaharlal Nehru Port Trust (JNPT) is planned over a reclaimed land of 100 hectares. Uran creek predominately consists of the estuarine deposit of very soft to soft marine clay. They are characterized by low shear strength, very low bearing capacity and exhibit large settlement when subjected to loading. The additional load causes the significant magnitude of consolidation settlement over a considerable period of time. Thus for development projects on top of soft soil, the postconstruction settlement would be of primary concern.To accelerate the consolidation pre-fabricated vertical drains (PVD) were used. Pre-loading procedure was adopted to minimize the post construction total and differential settlements. PVD’s were installed at 1.0m and 1.2m c/c triangular pattern. Locally available borrow material is used as a reclamation material. The reclamation material has been placed over the existing sea bed level by land based method/end tipping method and created the working platform. The level of working platform is decided based on the tide data and it has been selected such that work should be affected during highest high water level. The PVD has been installed from the working platform and subsequently all the field instruments have been installed from the same level. Five different types of field instruments are installed to monitor ground improvement works."

Jan 1, 2017

By Raymond J. Castelli

The paper provides a general overview of the numerous types of earth retaining systems currently available, and organizes these various systems by several classification methods. These classifications can be used as a guide in identifying the appropriate type wall or walls for any specific project application. As a further aid in sorting through the numerous wall alternatives for a specific design or construction project application, the paper suggests a systematic approach for wall selection, and presents helpful charts summarizing the general advantages and disadvantages, and typical limitations for the currently available wall systems.

Jan 1, 2003

Jan 1, 1989

By Richard F. Sliwoski

The Virginia State Capitol was designed by Thomas Jefferson and constructed in 1785. The Capitol is of great historic and architectural significance to not only the Commonwealth of Virginia but to the nation. It is the oldest operating Capitol in the U.S. and required a total restoration/renovation as well as an expansion to continue to remain functional. Site conditions dictated that the expansion (a new visitor center) be placed underground on the south side of the Capitol building, requiring a 40-foot deep excavation approximately 5 feet from the Building. Because of its historic significance, every measure had to be taken to ensure the safety and function of the Capitol during construction. The construction techniques that were used to make the deep excavation and protect the historic Capitol included a tied back concrete slurry wall, jet grouting, compensation grouting, and instrumentation monitoring. This paper describes the history of the Capitol building, the techniques that were employed for construction of the deep excavation, results of the latest movement monitoring, and factors contributing to meeting the restrictive movement goals.

Jan 1, 2006

By Naresh Koirala

The Greater Vancouver Regional District completed installation of a 2.5 Km long, 2400 mm diameter concrete sewer in Delta, British Columbia in 2000. The sewer traverses through area of peat and soft ground. The ground investigation along the sewer alignment consisted of cone penetration tests and auger drilling with standard penetration tests. The gravity sewer is supported on precast, pretensioned spun concrete piles imported from Malaysia which had never been used for a major project in North America. The capacities of the installed piles were tested using pile driving analyzer (PDA) and three static load tests. A total of 46 PDA tests were carried out during pile installation. The paper describes the pile vetting process the owner went through prior to accepting the piles for use in the project and performance of the piles. It compares the pile capacity estimated from the PDA tests with that estimated from soil mechanics methods using data from cone penetration tests and standard penetration tests. The ranges of estimated capacities calculated by different methods are discussed from design capacity selection considerations.

Jan 1, 2004

By Zhang Yaonian

This paper describes full-scale tests on ten large bored piles with grouted end conducted for three projects in the urban area of Fuzhou city. Test program included site investigation, pile installation and end grouting. The piles were instrumented with strain gages and load cells to determine load distribution in the piles. Test results showed that end grouting improves load-settlement performance of bored pile. End grouting significantly increases the shaft resistance near the pile end. The better the end condition, the greater the shaft resistance. The average shaft resistance of the bored piles with grouted end is much higher than that of piles without grouting.

Jan 1, 2004

By Masaki Kitazume, Yoshiaki Kikuchi

"Abstract Pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The deep mixing method, an in-situ admixture stabilization method, was developed in 1970s in Japan and the European countries, and has been frequently applied to many construction projects for various improvement purposes such as increasing bearing capacity and horizontal resistance, reducing ground settlement, preventing liquefaction and so on. The design methods, execution procedure and quality control and assurance (QC/QA) of the method are standardized or specified in many countries. These standards, specification and/or technical manual have been a remarkable contribution to spread the techniques throughout the world. The QC/QA is one of the major concerns for clients and engineers who have poor or no experience of the technologies. In order to assure the high quality of deep mixing work in the global market, it is necessary to establish the concept of QC/QA and correlate the output of different procedures. Upon the request by the organizing committee of the DFI-EFFC International Conference on Piling & Deep Foundations, the authors conducted survey of the specifications and standards on the piling and deep mixing technologies in Asian countries. In this manuscript, the results of survey are briefly introduced by comparing these specifications and standards.IntroductionThe pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The design method, execution procedure and quality control and assurance of pile foundations are standardized in many countries based on the accumulate research results, laboratory and field experiences. In Japan, steel pipe piles are mainly constructed by hammer driven in port construction. On the other hand, precast pre-stressed concrete piles or cast-in-place piles are mainly used in on land construction. When precast pre-stressed concrete piles are constructed, piles are usually set by inner excavation method because of preventing noise and vibration problems. More than 50 years ago, noise and vibration problems had not been serious problem in Japan, but around 50 years ago, they became serious and now less noise and vibration construction methods are used for pile construction on land in Japan. In Asian countries, though piles used for construction have a lot of variety, precast pre-stressed piles are commonly used. In this report, execution controls of construction methods of steel pipe piles and precast concrete piles are mainly considered."

Jan 1, 2014

By J. M. Pei

In this paper, the nonlinear finite element analysis is used to study the support system of a tunnel which is designed to pass through deep-embeded stratum. The rock mass is rather intact, though a section of tunnel will pass through the weak belt. Under the influence of the high ground stress, the condition of stability and the form of support become complicate. This paper, talcing into account the nonlinear properties of rock mass and the Interaction between rock, and support, makes a comparison between the two kinds of soft and rigid support systems, and analysed the changes of their bearing forces.

Jan 1, 2010

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By Scott A. Walker, Frank L. Rollo

"The San Francisco Museum of Modern Art (SFMOMA) in downtown metropolitan San Francisco, California, is supported on a mat foundation. Although the mat foundation of the original museum was designed to accommodate a future expansion, the plans for expansion that developed in 2010 required a larger footprint to accommodate the new space requirements of the museum. The new, larger expansion was designed by lead architect Snohetta. It will be a tall 12-story, steel-framed building occupying an area that was once the eastern part of the existing museum as well as two adjacent and newly acquired parcels.As designed, the expansion includes a 30-foot-deep excavation which is surrounded by adjacent buildings and improvements. Because of variable subsurface conditions at the site, geotechnical challenges included mitigating anticipated differential settlement between the existing and new foundations, preventing overstressing of the existing mat foundation, controlling groundwater to prevent settlement of surrounding improvements, and providing temporary support of adjacent structures during excavation for the new basement.To address several of the geotechnical challenges, soil-cement mixed (SMX) ground improvement was recommended by Treadwell & Rollo. However, during contract negotiations and construction, the specialty contractor proposed using jet grouting as an alternative technique for ground improvement. The jet grouting approach was accepted in principal, but when implemented was only marginally successful. Accordingly, the contractor eventually installed SMX panels using a Cutter Soil Mixing (CSM) machine. Because the CSM machine was a late arrival during construction, the contractor was not able to take advantage of the ground-improvement technique to install many of the shoring elements that we had originally recommended (such as the cut-off shoring wall). In the end, SMX panels were installed as ground-improvement beneath the new mat foundation to (1) reduce the potential for liquefaction in clean sand below the groundwater by providing increased rigidity to the soil, (2) reduce the potential for disturbing a weak underlying marsh deposit during construction, and (3) transfer vertical building loads to a layer of underlying dense sand.This paper also discusses the quality control and quality assurance programs that were implemented to check that the ground-improvement techniques used were thorough and complete and provided the required strength to transfer the new foundation loads to the underlying strata."

Jan 1, 2014

By Edward J. McNamara

People in the real estate industry are fond of saying that the three most important features of a piece of property are, in order, location, location, and location. This is perhaps the reason that the owners of a well known high-end restaurant chain chose to spend $15 million dollars to renovate 5000 square feet of basement in a 22-story commercial building in the heart of New York City's Time Square. The goal was to create a music club with a stage area and dance floor with a mezzanine level surrounding the dance floor. In order to create the 50' x 40' dance floor and 20' x 40' stage area, 3 concrete columns were removed. New transfer girders were used to transfer the loads of these columns to new steel columns. For the mezzanine, nine columns had to be underpinned. All work continued while the restaurants, shops and offices above carried on business as usual. This paper details some of the means and methods utilized as well as the challenges faced by Underpinning & Foundation Constructors, Inc. in underpinning the columns and installing the new transfer steel.

Jan 1, 2000

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

By Wolf-R. Under

For improvement of urban traffic infrastructure, the City of Amsterdam is cur­rently constructing the 9.5 km long North-South Metro line passing through the central districts of Amsterdam. Focal section of the project is the Central Station linking the NS Line with the Central Railway Station, the East Metro line, new bus and tramway terminals, ferries and individual traffic. Construction works required for the project are of high complexity and technical standards. They are executed under severe restrictions concerning programming, space, logistics, and impact on the integrity of existing buildings and structures as all existing installations and facilities have to maintain fully operational during the construction period. The paper deals with the main geotechnical features of the project and in particular with the diaphragm wall and bored pile construction at the Voor-plein and the De Ruijterkade sections of the Central Station.

Jan 1, 2006

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

By O&apos, M. W. Neill

Mini-piles have been found to be a practical, technically correct remedial underpinning method. They can be constructed in limited access areas with very little disruption. Experience indicated that mini-piles installed using a down-the-hole soil displacement hammer would be particularly effective in the "bottomless" Beaumont Clay formations in the Houston, Texas, U.S.A. area. The University of Houston Foundation Testing Facility was ideally suited to perform tests on mini-piles. The availability of extensive geotechnical data and previous pile test results was invaluable in evaluating the mini-pile test data. As expected, the mini-pile test results were consistant with test results from large sized driven piles in the same soil formation.

Jan 1, 1989

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit's new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999