Search Documents

By C. Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in the flotation circuit were calibrated using a dynamic grinding/flotation simulator. Predicted values are multiplied by g/t ratios to calibrate reagent flow. The transfer functions are currently integrated into the distributed control system at Les Mines Selbaie.INTRODUCTIONThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970's there have been numerous publications dealing with practical applications of flotation process control. A review of that literature shows that basic feedback and feedforward controls are the two preferred strategies for flotation processes. Some advanced control schemes started to emerge (e.g. Zaragoza and Herbst, 1988). Feedforward and feedback aim at reducing the effect of the following flotation process disturbances (e.g. McKee, 1991):0 Changes in throughput;0 Changes in feed grade;0 Changes in particle floatability (size, liberation, surface oxidation ... );0 Deliberate changes of set-point;Feedforward strategy acts on manipulated variables, mainly reagent addition, to attenuate the effect of disturbances such as changes of feed rate and grade. The feedforward strategy is driven by measurements of disturbances. Feedback control acts to compensate unmeasured disturbances, such as ore floatability, and to bring process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by set-point error, caused by either a deliberate change of set-point or unaccounted disturbances.This paper proposes a way to improve feedforward control schemes by addition of a simple model of solids transportation. The feedforward strategy considered in this paper is of ratio type, i.e. the manipulated variable is changed according to a predefined ratio between this variable and the measured disturbances. A typical example is the ratioed reagent addition to mass flow of ore."

Jan 1, 1993

By Simon Pelletier, Jose Delgadillo, Dave Page, Pramod Kumar, Raj Rajamani, Dilek Alkac, Martin Fillion

"In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal’s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned.First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized."

Jan 1, 2012

By M. Jackman

"Froth stability is critically important for an effective separation of fine and ultrafine particles using column flotation. While a desirable froth stability is required to facilitate the drainage of entrained gangue particles for secondary cleaning, excessively stable froths could create problems in separation efficiency and down-stream processing. In this work, we demonstrate that a stable foam was produced using a poly (N-isopropylacrylamide) (PNIPAM) solution at the temperatures below the critical solution temperature. In contrast, very little foam was produced at the temperature above the critical solution temperature (~32 oC) of PNIPAM. We can also tune the foam stability by changing the temperature of wash water. When warm water of temperature of 50 oC was applied, the foam collapsed and diminished. This is probably attributed to the switching of PNIPAM molecules from coiled to a globule conformation as the temperature is increased. Our results indicate that the foamability and foam stability can be tuned by tempartureresponsive PNIPAM. This is the first time that thermo-responsive PNIPAM has been shown to have potential as a modifier of froth stability in column flotation.INTRODUCTIONIn mineral processing, column flotation has become a more prevalent process in the separation of fine mineral particles (typically < 100µm). Traditional flotation cells are sometimes less efficient in selective separation of ultra-fine particles (Kohmuench et al., 2009). The efficiency of flotation columns is dependent on the froth stability at the top of the cell to drain the unwanted gangue particles entrained in the froth. The greater froth height in flotation columns, compared to mechanical flotation cells, gives a longer froth residence time, allowing more of the drainage process to take place before the froth reports to the launderer. Secondary cleaning, by applying a wash water shower to the froth, enhances drainage of gangue particles entrained in the froth, and improves the recovery of the targeted minerals (Finch et al., 2007).While a stable froth is desirable to facilitate drainage of entrained gangue particles, greater amounts of fine particles have been found to contribute to excessively stable froths which could create problems for down-stream processes (Bethell et al., 2012). Operators have tried spraying additional wash water on the froth, and reducing frother dosage to destabilize the froth and to prevent backup at the launderer. The former is sometimes inefficient, and the latter results in unacceptable recovery loss. Currently, the best practice is often the installation of larger froth launderers, adding expensive defoaming agents, and/or using deaeration tanks (Bethell & Luttrell, 2005)."

Jan 1, 2016

By Yuhua Wang, Wei Sun, Dongfang Lu, Yuehua Hu, Tao Jiang

"With the continuous depletion of high-grade tungsten ores, the low-grade refractory wolframite has become an important source for the tungsten industry. However, the large-scale utilization of low-grade refractory wolframite is disappointedly scarce, it is due to leanness of valuable minerals, complex mineral characterization and use of toxic collectors.The aim of this study was to develop an environment-friendly processing flowsheet, which was used for beneficiation of low-grade tungsten ore containing 0.45% WO3 from New Brunswick in Canada, and the content of arsenic is 0.68% in this materials. The objective of beneficiation studied was to obtain a concentration containing 60% WO3 with less than 0.5% of arsenic under the condition without any flotation reagents. In this environment-friendly processing flowsheet, magnetic separation technology, classification and gravity separation technology were combined and employed. Firstly, magnetic separation was employed for the first pre-concentration process, over 95% of the feed was rejected as the final tailings, meanwhile, over 85% of arsenic minerals were removed with tailings. Secondly, gravity separation tests were employed on the classified magnetic pre-concentrate in the second pre-concentration process, a second pre-concentrate with WO3 grade of 54.32% and As grade of 5.41% was obtained. Finally, two stage magnetic cleaning were conducted on the second pre-concentrate for upgrading the second pre-concentrate, the mostly arsenic and gangues were removed from the second pre-concentrate. Finally, this novel processing achieved an effective recovery of fine wolframite from low grade tungsten ore with high arsenic. A concentrate with WO3 grade of 64.81% were obtained in new opened processing flowsheet, and As grade was less than of 0.5% in this concentrate. Furthermore, remarkable feature of this processing flowsheet is environment-friendly due to avoid using the toxic flotation reagents during the whole mineral processing.INTRODUCTIONTungsten is an essential metal and is the most widely used in industrial production such as national defense, electro-mechanical products, textile and leather sectors (Srivastava et al., 2000). Wolframite and scheelite are the main mineral sources of tungsten metal. With the continuous depletion of high-grade tungsten ores and the increasing demand for tungsten alloy, the low-grade refractory wolframite has become an important source for the tungsten industry. However, the large-scale utilization of low-grade refractory wolframite is disappointedly scarce, it is due to leanness of valuable minerals, complex mineral characterization and heavy use of toxic collectors."

Jan 1, 2016

By A. Jafarnia

Aluminum alloys are frequently grain refined during solidification in order to promote the formation of an equiaxed grain structure in the casting. The application of Ti-based grain refiners and/or Ti containing master alloys for improving mechanical properties may result in formation of Al-Ti based intermetallics. Although the grain refinement produces many desirable qualities in aluminum castings such as improved castability and mechanical properties, the addition of Ti to Al-Si foundry alloys may lead to the formation of some undesirable intermetallic particles such as AlTiSi and cause a number of operational problems such as nozzle blockage due to segregation and agglomeration of aluminide particles within the nozzle. There are several questions to be clarified when minor amount of Ti is added to Al-Si alloys. They include nucleation and growth of AlTiSi particles, their morphologies and orientation relationships with aluminum matrix and the dissolution of these intermetallics during the course of solidification and/or post solidification treatments. The current study was initiated to study the process and possible mechanism of aluminide dissolution and the related phenomena such as segregation and agglomeration. It reports the results found during reheating of laboratory prepared Ti-added A356 alloy at three temperature ranges of below solidus, mushy zone and above liquidus.

Jan 1, 2004

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

By D. Milne

Laser profilometers exist for obtaining very accurate two and three dimensional profiles of joint surfaces. The application of this technology is not commonly applied to the collection of field data on discontinuity surface roughness. Rugged and portable field devices are not commonly used and the value of the possible field data that can be collected has not been well recognised. This paper reviews commonly used field techniques for assessing discontinuity roughness, discusses the value of this data and presents a new laser profilometer design for field application.

May 1, 2009

By E. Faria

"The Santa Rita mine is located in north eastern part of Bahia in Brazil and is owned and operated by Mirabela Mineração do Brasil Ltda. Typical SABC circuit was designed as the preferred option for the 4.0 mtpa (500tph) to produce a P80 of 125um for flotation. Although the SAG was originally designed to operate with conventional radial pulp lifters, later it was fitted with Outotec’s Turbo Pulp Lifters – TPL (Latchireddi, 2005). The milling circuit commenced commissioning on the 24th of October 2009 and the milling circuit achieved the nameplate capacity within days. with small and relatively simple measures to rectify. Since commissioning, the SAG mill has been working in fully autogenous grinding (FAG) mode with no balls (in contrast to the estimated 10% ball charge) and has been consistently treated up to 650tph.This paper examines the comminution design process, the operating philosophies, start-up experiences, post commissioning optimization and future development works. An evaluation of mill performance relative to the design criteria for the project life to date is also included."

Jan 1, 2012

By S. Banisi, J. A. Finch, A. R. Laplante

"A technique for on-line simultaneous estimation of gas and solids holdup (volume fraction), based on a combination of conductivity and pressure difference measurements, is proposed and tested in a laboratory flotation column (10cm in diameter and 447cm in height). Fundamental concepts underlying this technique and the effect of relevant parameters are discussed. In the studied range, 3-30 %v/v gas holdup and 2-18 % v/v solids holdup, experimental results showed good agreement between the estimated and actual holdup values (as determined by an isolating technique). The relative accuracy of the solids holdup estimation increased when solids density or solids concentration increased. Frequent re-calibration of pressure transducers was found necessary for accurate phase holdup estimation.IntroductionGas holdup is a key parameter in controlling the performance of flotation columns. For example, flotation rate is affected by bubble size and gas rate both of which, in turn, affect gas holdup. Moreover, gas holdup also determines the slurry residence time which indicates a direct influence of gas holdup on recovery.Gas holdup determination has been the focus of many studies (e.g., Castillejos, 1986; Marchese et al., 1992). Some of the techniques which have been used are given in Table 1."

Jan 1, 1994

By Anthony J. Deevy

"The Magino gold mine is located 45 km northeast of Wawa, Ontario. There was limited gold production in the late thirties. The present operation was officially opened in October 1988 and produced gold until September 1992. It was a 635 tonnes per day, decline-accessed mine, with ore coming from several small blast hole and shrinkage stopes.The host for the gold is the Webb Lake granodiorite stock which was intruded into the Goudreau Lake Deformation Zone. This east-northeast-striking deformation zone overprints the generally east-west- striking isoclinally folded metavolcanic and metasedimentary rocks, which make up the east end of the Michipicoten greenstone belt. The ore-shoots are controlled by dextral delatancy associated with the Goudreau Lake Deformation Zone. Shearing, bleaching and silicification accompanied the gold emplacement. IntroductionThe following is a general information paper on the Magino gold mine which is located 45 km- northeast of Wawa toward the east end of the Michipicoten greenstone belt. This paper summarizes the discovery, exploration and development history of the deposit. The geological characteristics are described, including regional geological setting, local mine geology, mineralization, alteration and structural history. The mining methods and the contribution of the geological staff to the successful development and mining of the gold deposit are also mentioned."

Jan 1, 1994

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters – usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, N. Andrade

In this work, the age-hardening behavior of cast Al-Si base alloys was investigated. It was found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu-Mg alloys. TEM observations reveal that the age-hardening behavior is related to the precipitation sequence of the alloy. For the Al-Si-Cu-Mg alloy, the first aging peak is the result from the high-density GP zones, while the subsequent are from metastable phases. The transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks.

Jan 1, 2006

By Hani S. Mitri

Strainbursts in brittle rock are common to deep underground mines. The state of stress at the boundary of mine openings is dictated by a biaxial stress/loading condition. This paper reports the results of a series of biaxial compression tests carried out on 100 mm cubic samples of norite rock, under different horizontal-to-vertical stress ratios. The results indicate that the biaxial compressive strength is considerably higher than the uniaxial one. It is found that the norite sample behaviour under biaxial loading mirrors field behaviour where shearing and progressive spalling of the opening boundary are observed prior to strainbursting. Sample failure is initiated by rock spalling at the sample free faces, i.e. in the plane of biaxial loading. Finally, it?s the out-of-plane shear failure mechanism that causes the sample to collapse. Shear failure takes place violently and abruptly and is accompanied with considerable audible noise.

Apr 1, 2005

By Malcolm Powell

"Predicting the performance of the whole mining process is surely the holy grail of predictive simulation. This can be named ‘Integrated Process Prediction’.The objective is to be able to predict the response of the processing chain, from mining to concentration, to changes in the ore type. This can apply to greenfields design – selecting processing options to optimise the overall mine performance within the constraints and aspirations of the greater community and environment; expansion and optimisation of existing plant to deal with changes in economic drivers and ore types; and on-line control – predictive reaction to ongoing changes in ore processing types in an operation.In order to achieve this there are several broad key components that are required: ore characteristics based on in-situ rock properties; a reliable 3D map of the ore body by the key processing parameters; prediction of how the rock fragments and the energy requirement to break it; the ability to predict and track progressive mineral liberation of the rock through the reduction process; the response of rock to separation processes as a function of the rock mineralogical properties. This requires the identification of primary rock properties and associating them with the rock particles as they move along the mining process chain to a concentrate or various forms of waste.This paper looks at the value of this integrated approach; the challenges it poses; the technology and capability we require; and how as a mineral processing community we can address the challenges."

Jan 1, 2016

By R. R. Dickson

Princess colliery, the largest mine operated by the Old Sydney Collieries, Limited, commenced operations in 1877. It was the first mine sunk in the Sydney coal field with the primary object of working submarine coal. Until 1925, coal was won by the room-and-pillar system. By that year, the depth of cover over the workings was 1,300 feet, and physical conditions had become such that it was impossible to extract completely the pillars formed by the working of the rooms. Because of this, the system of work was changed to longwall in the early part of that year. At first, an orthodox hand-pick method was used, with gate roads laid off at 50-foot centres and the mine cars loaded by hand directly on the longwall faces. Later in the year, the first machine-cut conveyor longwall faces were started.

Jan 1, 1946

By M. B. Kime

"Discrete-element method (DEM) modelling is a powerful tool for studying particulate systems within the mineral processing industry. DEM simulations were conducted to investigate the power draw, load behaviour, and impact energy profile of an experimental ball mill under different milling conditions. The variables considered were mill rotational speed (percent critical speed), ball size, and lifter face angle. The simulation results indicated that the grinding efficiency would be enhanced by using 80% critical speed, 30 mm ball diameter, and 45° lifter face angle. These findings can be useful in guiding actual ball milling tests involving an ore sample.RÉSUMÉ La modélisation par méthode des éléments distincts (MED) est un outil puissant qui permet d’étudier les systèmes particulaires au sein de l’industrie de traitement des minerais. Des simulations par MED ont été menées de façon à étudier le profil de la consommation énergétique, du comportement de la charge et de l’énergie de rupture d’un broyeur à boulets expérimental dans diverses conditions de broyage. Parmi les variables prises en compte figuraient la vitesse de rotation du broyeur (vitesse critique en pourcentage), la taille des boulets et l’angle de coupe de la cornière élévatrice. D’après les résultats de la simulation, on pourrait améliorer l’efficacité de broyage en utilisant une vitesse critique de 80 %, un diamètre de boulet de 30 mm et un angle de coupe de 45 ° de la cornière élévatrice. Ces résultats peuvent se révéler utiles pour les essais concrets de broyage à boulets impliquant un échantillon de minerai."

Jan 1, 2017

"In today’s world of complex projects, where engineering and execution are supported by a high level of project management and systems, how critical is the human factor in design engineering. Based on his involvement on a variety of projects, Tony Lipiec will relate his experiences as the impact of 4 factors: the ‘team’ involved in the design and execution of the project; the project and information systems supporting the project; the impact of scope, time, and budget; and finally the selection of the proper success criteria to judge the project and the people who have enacted the project.The discussion of the team will relate to the quality of people and the impact of their knowledge, attitude and experience. It will also look at the relationships and interests of the various stakeholders. Decision making and taking responsibility will be discussed.Supporting the team are the management, document and information systems. The value that these systems bring to the project as a whole will be examined. How project size impacts the applicability of the systems will be discussed.Scope, time and budget are recognized as critical. Reference will be made to the interplay between these components which are vital to project success. The issue of iterative design and whether it is necessary will be considered together with the development of supporting technical information.Finally the selection of the proper success criteria and the awards provided to the team can have a big impact on the final, production success of the project. The author will discuss his views on the impacts of these on EPCM projects."

Jan 1, 2016

By M. A. Nadar

Harsh and dynamic construction sites are generally equipped with cranes in order to rapidly and conveniently move heavy loads from one location to the other. If not properly inspected and managed, this operation can be very hazardous and lead to accidents. As such, a reliable and self-contained monitoring system that can update construction and safety personnel about the status of the crane, the weight of the load lifted, the location of the boom with respect to nearby buildings and other tower cranes, and the weather conditions under which the crane is operating, is deemed necessary. This can lead to significant time and cost savings as well as safety and productivity improvement due to the accuracy and immediacy of relevant on-site crane information delivery. This paper takes the initial steps and presents research targeted at evaluating the capability of wireless sensor networks (WSN) for monitoring tower crane operations in construction environments. A reliable long range WSN system is implemented and information is obtained from various special-purpose sensors (temperature, wind, proximity, etc.) mounted on special motes that relay data to and from each other and a central hub. The latter continuously monitors and manages network performance and relays incoming data to the host application. This application, in turn, displays the received data, and maps it onto a user-friendly visualization scheme, triggering alarms when a set of pre-programmed rules and safety conditions are crossed. The components of the proposed system have been tested through proof of concept experiments and preliminary results highlighted the potential of WSN systems for improving monitoring of tower cranes and reducing related accidents on construction sites, especially in Lebanon and the Middle East region where safety precautions are usually not properly implemented.

Aug 1, 2013

By S. Maleksaeedi

On-site evaluation of strength using hardness is common for different materials. The lack of such relation for aluminum alloys has always been felt. In this work, a finite element analysis of plastic deformation and its distribution in Brinell hardness testing is presented. The analysis has been performed for different strength levels of aluminum alloys. By utilizing the Von Mises equivalent strain in hardness, it is tried to derive a correlation between hardness and strength values for the alloys under consideration. The derived correlation is verified using the experimental values available in literature.

Jan 1, 2004

By A. Probst, J. A. Finch

"Solids concentration (% solids) profiles and the clear liquid/slurry interface level (mudline) were determined from conductivity measurements in thickeners at Falconbridge' s Strathcona mill (Ni concentrate and non-mag thickeners) and Kidd Creek Division (Cu, Zn concentrates and final tails in the concentrator and thickeners in the Zn plant).The conductivity measurement system consisted of a probe 1.5 m in length with 24 electrode cells, a 24-channel relay, a conductivity meter and a computer. A conductivity profile is collected which locates the mud-line by the sharp change in conductivity. The conductivity measurements are readily converted to solids concentration profiles without need for calibration.The results from the conductivity measurements were compared with those from pressure profiles and direct measurements on local samples obtained using a modified Noranda sampler.It is concluded that the conductivity technique is applicable to locate the mud-line and to estimate the solids concentration profiles in thickeners. This on-line information could improve the operational efficiency of industrial thickeners.INTRODUCTIONAn automated, on-line technique for detecting the clear liquid/slurry interface (or mudline) and the variation in solids concentration with depth would enhance thickener operation and control. In some processes such enhanced control offers significant benefits. For example, in hydrometallurgical operations solid/liquid separation is often the process limiting step. Water treatment plants are increasingly expected to operate remotely and reliable sensing is vital.Current attempts to detect the mud-line include reflection of some signal (e.g. sonar), floats (Dahlstrom, 1985) and measurement of pressure (Rosenblum, 1991), and in one case, natural radioactivity of the solids (Johnston and Simic, 1991). A recent commercial development uses reflection from a vertical array of optical transmitters/sensors, which also gives local solids concentration (BTG Inc., 1991)."

Jan 1, 1993