Search Documents

By A. L. Valdivieso

"The correlation obtained by plotting pH of maximum adsorption of dextrin versus the isoelectric point of involved metal hydroxides can be used to predict the depressing effect of dextrin on flotation in ""pure"" sulfide mineral systems. Sulfides are strongly depressed by dextrin whenever their surfaces are coated by the corresponding metal hydroxide. The efficiency of dextrin as a depressant is affected by the adsorption of the sulfhydryl collector. Hydrolyzable cations modify this relationship in flotation of sulfide ores. This type of deviation of the real-life systems from the predictions based on the behavior of the pure systems shows the possible ways that could be followed to further improve the obtained correlations. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by"

Jan 1, 2009

By M. Alvarez-Silva, A. Uribe-Salas, J. A. Finch, M. Mimezami

The point of zero charge (PZC) of electrokinetically anisotropic minerals (chlorite and serpentine) was determined using the Mular-Roberts (M-R) titration technique, and compared to isoelectric point (IEP) obtained from electrophoretic mobility measurements. To validate the M-R technique, the point of zero charge and isoelectric point of two isotropic minerals (alumina and silica) were shown to be comparable. For serpentine and chlorite, respectively the PZC was found at pH 4.3 and 4.6, while the IEP occurred at pH 3.2 and <3. Settling tests showed that the maximum settling rate, which corresponds to aggregated particles, for chlorite was around pH 3, i.e., close to the IEP; lizardite did not show a conclusive maximum.

Jan 1, 2009

By Lizelle Glaner

An investigation was carried out by Mintek to investigate the influence of additions of gold to ?Fecraloy?, alloys based on Fe-Cr-Al. The aim was to try and improve the oxidation resistance of the ?Fecraloy? alloys at elevated temperatures over extended periods of time. The ?Fecraloy? alloys are very oxidation resistant alloys already employed in industry as substrates for metallic catalysts in auto-catalyst systems for high performance cars. Since their life and durability is limited by the slow, but steady, oxidation of the substrates, any change in the growth or stability of the oxides could be an improvement.

Oct 1, 2003

By Emmanuel Henry

Hanging wall deformation monitoring at the Kiruna Mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening towards the Kiruna Town. In the quest for more effective monitoring techniques, LKAB decided to evaluate satellite-borne Synthetic Aperture Radar (SAR) interferometry?s ability to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the Mining industry. This paper describes how subsidence is actually monitored on the Kiruna Mine?s hanging wall and gives an insight on SAR interferometry?s principle. The encouraging results are discussed as well as the technique?s benefits (continuous deformation mapping, low cost, fast, etc) and limitations (sensitivity to snow and vegetation cover).

May 1, 2003

By G. Anger, J. Enser, H. Antrekowitsch, S. Koch

Homogeneous chemical composition and microstructure are always necessary, but not always attained in practice. As-cast aluminium alloys tend to have a segregation microstructure. Features of the cast structure, which affect subsequent processing or properties, can be altered by the homogenization. The main task of the Department of Nonferrous Metallurgy was to investigate the effect of homogenization treatment on precipitation hardening of aluminium alloys 6061 and 6082. The effect of the solution heat treatment (SHT) temperature on the mechanical properties was also analyzed. The homogenized and non-homogenized rolling slabs were produced according to the usual conditions and methods. The metallographic investigations were carried out on the as-cast samples, after homogenization, after the hot and the cold rolling mill, and after natural and artificial ageing. Then, Brinell hardness measurements and tensile tests were conducted on both alloys in order to examine the influence of the homogenization.

Jan 1, 2006

By E. Lovera

ABSTRACT: The current study analyzes the feasibility of an odd operation: to obtain, using a properly tailored drilling and blasting scheme, blocks suitable for the production of dimension stone from tunnel driving. Clearly, a compromise must be found between the rate of progression and the achievement of workable blocks. As a case study, a civil work under consideration in northern Italy was examined. The work was planned to cross a conglomerate that has traditionally been locally exploited for the production of highly prized paving and lining stones with excellent strength and aesthetic features. Natural exposures and mined-out quarries were available for tests. The relevant rock data are given, blast designs are shown (within the limitations of contour accuracy), and the test program is described.

Jan 1, 2011

By David Stone

North American Palladium is the owner/operator of the Lac des Iles mine located 115 km north of Thunder Bay, Ontario. The mine has produced an average of 65,000 ounces of palladium since 1994. Lac des Iles is currently undergoing the first phase of a major expansion that will increase ore production from 2,400 tons per day to 15,000 tons per day. A future expansion is being contemplated for 30,000 tons per day. The current expansion will increase palladium output to 250,000 ounces per year. The mine plan for the ultimate pit results in an excavation 1 km long by 800 m wide and over 450 m deep. This makes the ultimate pit at Lac des Iles one of the ten deepest open pits in the world, and the largest in Canada. This paper outlines the geotechnical data collection and design methodology for the ultimate open pit at Lac des Iles.

May 1, 2001

By A. Hekmat-Ardakan

Conventional hypereutectic Al-Si alloys such as A390 are used principally for the casting of components used in wear applications requiring abrasive resistance such as in engine or compressor blocks. A comprehensive study was undertaken to investigate the potential of improving the mechanical properties of these alloys by the addition of magnesium. A thorough thermodynamic study of the effect of the addition of Mg to the conventional A390 alloy showed that Mg2Si starts to form as a primary phase at 4.2% Mg as well as in the products of the binary and ternary eutectic reactions forming the matrix. Experiments were carried out in producing castings with different cooling and solidification rates of alloys with up to 10% Mg. Mg additions were found to increase the hardness over the as cast alloy due to solid solution strengthening. Also, T6 heat treatment greatly improved the tensile properties of these alloy compositions due to the strengthening effect of the theta-Al2Cu phase. The elongation of these alloys generally decreases marginally with Mg content. The most significant property improvement of the alloys with higher Mg content is the substantial increase in wear resistance. This is attributed to the dispersion of smaller particles of Mg2Si and their coherence with the matrix as compared to the large Si particles in the conventional alloy. A new rheoforming process for A390 is presented that improves the processing of the semi-solid slurry. Structure modification elements were also added to refine the primary and eutectic silicon greatly improving the processing of the semi-solid slurry.

Jan 1, 2011

By V. Barranco, K. Yliniemi, A. Hubin, B. P. Wilson, D. Janas, M. Lundström, P. Hannula

Typical copper electrorefining electrolyte contains tens of grams of copper, some nickel and a wide variety of impurities. Some of these impurities comprise trace amounts of dissolved precious metals like Ag, Pd and Pt that currently are not fully exploited. This study presents an electrochemical method to recover precious metals via a combined electrodeposition-redox replacement (EDRR) process, where energy is used only to deposit copper during the ED-step, while the RR-step relies on the spontaneous replacement of copper by the precious metals (i.e. cementation). In order to conduct the recovery successfully, process parameters such as deposition potential (EDE), deposition time (tDE), redox replacement time (tRR) and the number of cycles (n) was adjusted. Investigations performed in synthetic electrolyte (40 g/L Cu, Ag = 10 ppm) proved the possibility to recover a high purity silver. Short deposition times (tDE) were found to result in small Cu particles that provided a suitably high surface area for silver cementation. In addition, experiments performed in real industrial electrolytes containing 44 g/L Cu and 54 ppb Ag (Boliden Harjavalta, Pori), demonstrated that EDRR could attain Ag recoveries of between 46–67% in an energy efficient, additive-free manner. INTRODUCTION The raw materials used in the state-of-art primary and secondary copper smelters contain mainly base metals, but also notable amounts of Ag, Pt and other precious metals. These valuable metals distribute mostly into the copper matte during the pyrometallurgical treatment (Tirronen et al., 2017) and end up into the cast anodes. During the electrorefining stage, metals more noble than copper such as gold and platinum, are not dissolved but enrich into the anode slimes. In contrast, silver may dissolve slightly and thus, minor chloride addition is used to retain silver in the slime as sparingly soluble AgCl. Moreover, other metals less noble than copper may also dissolve, such as nickel. Therefore the electrolytes used in electrorefining typically contain substantial amounts of copper, nickel and even arsenic as well as minor metals such as antimony and bismuth. In the Boliden electrorefinery these were reported to be in the magnitude of 51.2– 60.4 g/L of Cu, 10.9–15.8 g/L Ni, 7.2–15.9 As, 0.2–0.4 Sb and 0.1–0.4 Bi with an associated sulfuric acid concentration of 139–155 g/L (Lehtiniemi et al., 2018). Copper is the most noble of the dominating base metals in the electrolyte and is thus deposited on the cathode as 99.99% purity LME-A grade. Anode slimes are collected and subjected to precious metals treatment e.g. via pressure leaching—selenium recovery— Doré smelting—Ag refining—Au/Pt/Pd leaching and reduction process (Ludvigsson & Larsson, 2003). The Pori refinery, operating in Finland since 1941, not only produces 133 000 t Cu cathode and 2300 t nickel sulphate annually but also 66 t silver, 4.6 t gold and palladium and platinum (in year 2017).

Jan 1, 2019

By H. Staton, XPS Consulting & Testwork Services, T. Deng, M. Kelvin

"Lundin Mining’s Eagle Operation, located in Marquette County, northern Michigan consists of a mine and concentrator that processes a Ni-Cu-(PGE) ore. Mine production began in 2014 and is expected to achieve production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year. The ore is trucked to the Humboldt Mill, where both a Ni and Cu concentrate is produced.XPS Consulting & Testwork Services (XPS) has assisted the team at Eagle since 2013. Prior to start up, the ore was piloted at the XPS lab in Sudbury, Ontario to demonstrate the concentrator flowsheet and establish flotation operating strategy. XPS consulting metallurgists worked closely with the Eagle team during the commissioning of the plant providing troubleshooting, sampling, metal balancing expertise and support. Finally, a series of monthly composites over a 6 month period was submitted for mineralogical characterization to assess plant performance, identify opportunities for improvement and to provide a baseline for the future operation.Lundin’s investment to test the ores ahead of mining and to team with XPS’s experienced mineral processing engineers to help commission the plant has led to the plant achieving concentrator production targets shortly after startup. The commitment to training and implementation of best practices, and a culture where ongoing testing is the norm, puts the Eagle Operation on sound footing for future operation.INTRODUCTIONLundin’s Eagle Mine is a subsidiary of Lundin Mining located in the upper peninsula of Michigan. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 2 hours to the Humboldt mill.The ore is an ultramafic hosted high grade Cu Ni deposit and exists as either massive or semi massive sulphides. The high resource grade of Cu (2.49%) and Ni (2.93%) make this a valuable ore source. (Owen & Meyer, 2013) A metallurgical team was put together by Lundin to ensure the mill was designed and commissioned to optimize metallurgy in the shortest time from this valuable deposit. The commissioning plan targeted commercial production by Q1 2015."

Jan 1, 2016

By A. Karzhau, B. Aldamzharov, Y. Tussupbekov

"This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of the mine 24 hours a day. The mine auxiliary ventilation has been designed with the maximum length of ducting systems with extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal. The mine needs additional investments for re-designing ventilation network and therefore needs to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation network optimisation processes at the operational metal mine in Kazakhstan. Mine ventilation surveys were undertaken for validation of the computerised ventilation model. The mine ventilation network modelling has been undertaken to be compliant with Kazakhstan mining regulations. Results of the mine ventilation optimisation processes were analysed in terms of financial risks for investments into reconstruction of the ventilation shafts, extension of the ventilation network, variable speed fans and automated regulators. Savings were resulted from improving ventilation system efficiency by reduce airflow in areas without mining activity and redistributing existing ventilation capacity. Based on savings derived from the optimised ventilation network an additional NPV has been received. Stochastic modelling use Monte Carlo simulation producing representation of possible outcomes for the additional NPV considering electricity pricing as a major variability. As result probability distribution for the optimised ventilation network demonstrates the additional NPV in a range of 1.6 - 2.2 million US$ in the corresponding defined value of 90%. Moreover, there is only 5% chance that the additional NPV to be less than 1.5 million US$. Conducted risk analysis for ventilation network optimisation processes gives considerations on volume of investments into the mine ventilation system.INTRODUCTIONCosts for mine ventilation are typically increasing when mines expand to deep levels. Some underground mines in Kazakhstan still use continuously operating fans at its maximum capacity. This is not helping to save energy and costs that are in many cases very significant. This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of a mine 24 hours a day. The mine auxiliary ventilation has been designed with maximum length of ducting systems and extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal from the mine workings (Sabanov, 2019). The mine needs additional investments for re-designing ventilation networks and therefore need to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation networks optimisation processes at the operational mine in Kazakhstan. Mine ventilation surveys for validation of the computerised ventilation model have been undertaken"

Jan 1, 2019

By Nirmal Weerasekara

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By F. J. Guevara

A two-dimensional mathematical model for fluid flow and heat transfer in a sixin- line electric smelting furnace was developed to study the effects of temperature on slag viscosity in both the liquid and mushy zones. The model focused on the fluid dynamics of the molten slag and the effects on the formation of a slag freeze layer on the hot face of the furnace wall. Previous experimental and mathematical work, carried out under Ra number of 109 and using a fluid with Pr number of 65, showed that it is possible to mathematically describe the freeze layer formation over a vertical wall using a fixed-grid model. The chemical composition of the slag was taken into account through its effect on the viscous activation energy as well the solidus and liquidus temperatures. The results show that the flow pattern is strongly modified in areas of high viscosity, in front of the cooling system and at the slag-matte and slag-calcine interfaces. The results are discussed in terms of heat flux over the refractories and their effects on cooling system design.

Jan 1, 2007

By Y. Wang

In this study, homogeneous (unseeded) precipitation of nesquehonite (MgCO3.3H20) by the reaction of MgC12 with (NH4)2CO3 in supersaturated solutions at 30 °C was investigated. Factors which influence the precipitation of MgCO3.3H20, such as initial concentration, temperature, stirring speed, titration speed, equilibration time, have been studied. SEM images show that the initial concentration and titration speed have significant effect on nesquehonite&apos;s crystal morphology and particle size. In addition, stirring speed and equilibration time also have some influence on its properties. With the optimization of operating conditions, the crystals can grow up to a length of about 40µm and a width of 5µm, indicating good filtration properties. High purity nesquehonite obtained in this study was calcined to produce highly pure MgO at 800 °C as shown by XRD results. The novel process may be used to separate Mg and Li from high Mg/Li ratio brines in Qinghai, China.

Jan 1, 2007

This work illustrates the potential of two welding processes for joining AA1100-16 vol.% B4C metal matrix composite: laser welding process using a 4 kW Nd:YAG laser and Friction Stir Welding. A comparison is made between these two welding techniques in terms of microstructure and mechanical properties of welded joints. A large amount of brittle needle-like phases, together with some residues of B4C particles were observed in the fusion zone of laser welded joints. The use of Ti filler can improve the microstructure and increase the joint efficiency from 63% to 75%. On the other hand, the friction stir welding process being a solid state welding technique is interesting as it avoids the formation of brittle intermetallic phases. In addition, the breakage of B4C particles and the grain refinement of the matrix were observed in the weld zone. Consequently, FSW joints show much better mechanical properties than laser welded joints. Up to 100% joint efficiency can be achieved by FSW for annealed AA1100-16 vol.% B4C materials.

Jan 1, 2011

By S. Amira

The corrosion behavior of high pressure die-cast and thixocast AXJ530 magnesium alloys has been investigated in 0.05M NaC1 solution at pH 6.0 using potentiodynamic polarization tests, electrochemical noise (EN) technique, electro-chemical impedance spectroscopy (EIS) and scanning reference electrode technique (SRET). The behavior of die-cast and thixocast specimens were compared using each of these techniques and the results discussed. Further tests have been carried out with die-cast AZ91D alloy to better compare and interpret the results. Experiments indicate that the thixocast specimens of AXJ530 alloy have a better corrosion resistance than those of die cast alloy in neutral solution.

Jan 1, 2006

By Olivia Gamache

When working in remote and extreme environments, projects are faced with new challenges for engineering and project execution. This is heightened when also working in countries with a developing environmental regulatory framework, small skilled workforce available for recruitment, and minimal infrastructure such as power, roads, and water. There is an increasing realization that social and environmental aspects need to be built into project execution. Giving proper attention to these issues during project development and execution, and maximizing opportunities is an ongoing challenge.

May 1, 2013

By Reinis Sipols

AGENDA ? Introduction ? Definitions and Key features ? PEA - Preliminary Economic Assessments ? PFS ? Preliminary Fesibility Studies ? FS ? Feasibility Studies ? Costs and Risks ? Cash Flow, Economic Analysis and Reporting ? Recommendations for Improved FS accuracy INTRODUCTION ? The reporting of material information on mineral deposits has been governed by NI 43-101 legislation for almost a decade. ? The investment sector depends on the independent, professional QP to provide objective observations, comments and recommendations through all levels of geological, engineering and financial evaluation until a mine construction decision has been made.

May 1, 2013

By J. Q. Chen

The elastic-plastic behavior and the fracture mechanisms of two 2198 Al-Cu-Li thin sheets are investigated. The first material (2 mm thick) is in a recrystallized state after cold rolling. The second material (6 mm thick) is hot rolled and has a fibrous grain structure. The two materials are studied in both T351 and T851 conditions. Tensile tests are carried out along different sheet directions using flat and notched specimens. Fracture resistance was characterized using Kahn tear specimens and M(T) panels. Macroscopic fracture surface of smooth tensile specimens depends not only on testing material but also on the loading direction. For Kahn tear specimens, fracture is initiated in a small flat triangle whereas slant fracture is observed during crack propagation. Fracture mechanisms were investigated using scanning electron microscopy (SEM) and X-ray 3D tomography.

Jan 1, 2011

By P. Su

Friction stir spot welding of a range of Mg-alloys is investigated (AZ91, AZ31, AM50 and AM60). The peak temperatures during friction stir spot welding of all Mg-alloys are close to their solidus temperatures. Also, the apparent material viscosity of Mg-alloy sheet is lower than that when Al-alloy sheet material is spot welded. This is important since it means that the widths of the stir zones forming during spot welding of Mg-alloy sheet are smaller than those when Al-alloy sheet is welded (when identical welding parameter settings are applied). These lower apparent viscosity values must be taken into account during numerical modeling of the Mg-alloy spot welding process. The efficiency of energy utilization is very low when Mg-alloy sheet is spot welded and is of the same order as that when fabricating Al-alloy sheet. The energy generation contributions of the rotating pin and the tool shoulder are investigated. When the spot welding operation is carried out without the application of a dwell period, the contribution made by the rotating pin vis-à-vis energy generation is around 66%. The contribution made by the tool shoulder increases to about 65% when a dwell period of four seconds is incorporated during the spot welding operation. This increase results from a longer contact time between the tool shoulder and material within the stir zone, The failure load during overlap shear testing increases when the bonded area and the energy input increase during spot welding. Sample failure initiates from unbonded regions and from discontinuities at the edge of the stir zone. The formation tendency of discontinuities is increased when Mg-Alloy sheet is spot welded because of the limited deformation characteristics of the base material at lower temperatures.

Jan 1, 2006