Search Documents

By D. S. Campbell

THE chief factors influencing the decision to build the Big Missouri mill underground were the topography of the country and the climate. The location underground assured certain saving in the cost of operation, such as the hearing of the mill, shovelling snow, and handling ore, which, over a period of time, would offset the greater initial cost of the mill excavation and machinery installation underground, as compared with the cost of a like plant on the surface. At Gilman, Colorado, where conditions are somewhat similar, the Empire Zinc Company, at their Eagle mine, are treating their lead-zinc ore in a mill built entirely underground. Company officials made a study of this plant before proceeding with the mill at Big Missouri. LOCATION, CLIMATE, TOPOGRAPHY The Big Missouri mine is situated on the Upper Salmon river, 22 miles north of Stewart, B.C., which is at the head of Portland canal, a narrow natural channel which penetrates 100 miles inland from the coast into the Coast Range mountains. Stewart, the distributing centre for the district, is about 600 miles north of Vancouver. The Big Missouri claims lie on and down the sides of the Big Missouri ridge, which extends north and south between the Salmon River and Cascade Creek valleys. The ridge rises to an elevation of 3,600 feet, is about half a mile wide, and to the east slopes down to the Joker flats in Cascade Creek valley. The Big Missouri camp is located on the flats at elevation 2,800 (see Figure 1). Preliminary development of the property took place from this point with an adit driven under the ridge. The western side of the ridge slopes steeply down to the Salmon glacier at elevation 1,900. Ore found on the 2,850 level extended down, and, in order further to explore the ore-body, the 2,850 level was driven through to the west side of the ridge, a surface incline tramway was built, and a lower tunnel driven at elevation 2,350, five hundred feet below the original 2,850 level, from the west side of the ridge. This tunnel development avoided the necessity of sinking, which would have been costly, as the mine makes a great deal of water (see Figures 1 and 2).

Jan 1, 1938

By M. Maeda, H. Sasaki

"Precious metals such as platinum, palladium, and rhodium are commonly used for automotive catalyst converters. To recover these metals with lower environmental load and cost, exposure to zinc vapor was proposed as a pretreatment prior to acid leaching. Alloying with zinc is expected to enhance dissolution of precious metals and reduce the amount of toxic chemical agents required for the leaching. This study examined the effect of the alloying pretreatment using model catalysts. Catalysts were immersed in leaching solutions for a predefined time with or without zinc vapor pretreatment, and the amount of dissolved metals was then evaluated. INTRODUCTIONAutomotive catalysts account for large portions of the world consumption of platinum (Pt), palladium (Pd), and rhodium (Rh) (Butler, J., 2011). Because of their limited production and high prices, recovery of the precious metals from spent catalysts is obviously an important issue. A representative structure of an automotive catalytic converter can be described as a monolithic ceramic support with a honeycomb structure which is coated with porous oxides such as those of aluminum (Al2O3), cerium (CeO2), and zirconium (ZrO2) (Heck & Farrauto, 2001; Matsumoto & Shinjoh, 2007). Small particles of precious metals, originally several nanometers or less, adhere to the oxides.Typical recovery processes for precious metals from scraps are shown in Figure 1 (a)-(c) (Habashi, 1997; Yoo, 1998; Shibata & Okuda, 2002). Precious metals can be recovered by using non-ferrous smelters as Figure 1 (a) shows. Smelted along with metals such as copper (Cu), precious metals and ceramics in the scraps are absorbed into the metal phase and slag phase, respectively. Because the metals separate from Cu as anode slime in successive electro-refining, such a process can recover precious metals as co-products of Cu. However, in order to prevent negative effects on the principal process, a specialized procedure is needed. Figure 1 (b) is a specialized approach in which scraps are melted at elevated temperature with Cu called the Rose process. Here Cu works as a collector metal, and the absorbed precious metals are then concentrated by oxidation of Cu. Such a process can separate precious metals from ceramics constituting catalyst converters. Smelting at high temperature, however, requires extensive equipment as well as a high amount of energy. On the other hand, hydrometallurgical processes may be effective to separate precious metals from ceramics into an aqueous solution, because chemical agents can act on these metals selectively (Figure 1 (c)). Leaching of precious metals, however, requires strong acid and oxidizing agents because of their corrosion resistance; this makes liquid waste disposal and the large environmental load controversial. To solve the problem, a metal vapor pretreatment was proposed (Okabe, Yamamoto, Kayanuma, & Maeda, 2003a, 2003b; Kayanuma, Okabe, Mitsuda, & Maeda., 2004; Kayanuma, Okabe, & Maeda, 2004; Itoh, Kayanuma, Miyake, Kimura, & Maeda, 2005). A flow diagram of the process using zinc (Zn) vapor is shown by Fig. 1(d). Exposed to Zn vapor, precious metals are expected to form alloys which dissolve more easily than pure precious metals, thus reducing the use of chemical agents and environmental load involved with successive leaching. In previous research (Sasaki, Miyaki, & Maeda, 2010; Sasaki & Maeda, 2010, 2012), dissolutions of precious metal alloys formed by Zn vapor treatment were examined in hydrochloric acid (HCl) using an electrochemical method, and it was confirmed that these metals dissolved at higher rates from the alloys than from their pure states (Figure 2). In this study, the availability of the alloying pretreatment was demonstrated by testing on model catalysts in leaching solutions."

Jan 1, 2012

By V. Budinsky

In recent years the global mining industry has addressed its social and environmental responsibilities and numerous factors have contributed to this. Corporate Social Responsibility (CSR) is an important part of mining company strategy for practical implementation of the goals of sustainability, transparency, accountablity and good relationships with stakeholders:- investors, employees and communities. A key stakeholder for all mining companies is the local community which is affected by the mining operations. Companies must identify the emerging social and environmental trends, study the interests and concerns of various communities, address their needs and maintain a positive relationship. The CSR programmes of Czech coal mining companies are focused on surrounding community initiatives and sustainable responsible business. Mining in the Czech Republic is subject to strict rules and regulations and supervised by the State Mining Authority. Mining projects undergo rigorous approval procedures which encompass all operational measures at the different planning levels ? such as public participation in the authorisation process for mining projects, the application of the Environmental Impact Assessment Directive, environmental sustainability programmes, innovative solutions and flexible options offered by the mining company. One very important part is the preparation of the mining-technology preconditions and developing the integrated planning process in which all socially and politically relevant subjects in the mining operation surroundings are included. In an in-depth debate, all stakeholders may jointly develop the concept, in accordance with democratic principles. The optimally conducted dialogue process needs broad communication bases, including setting up theme-related joint taskforces, together with good moderation and the highly qualified support of technical experts. Using a case study of Severoceske doly a.s. Chomutov (SD Company) and the Czech Coal Group ? Czech leaders in the extraction of brown coal, this paper aims to examine the community development approaches and the CSR effectiveness of large scale mining companies. This paper brings a review of CSR and other such voluntary initiatives in the mining industry's proactive steps to contribute to societal well-being in a meaningful way. Key studies are provided by the projects ? Region with Better Perspective?, ?Stop Dust for Healthy Brezno Village?, ?Clever Heads for the North? and ?Coal Safari?. CSR issues are managed throughout all stages of the mine operation and beyond, long after the mine closes (e.g. post-closure programmes of new landscape, alternatives for reclamation including generation of lakes in former surface mines, conceptualization of industrial heritage). Communities need to be given the opportunity to help themselves through participation in CSR projects rather than being recipients of financial gifts from the company. A fair balancing of interests is the basis of any successful cooperation.

Aug 1, 2013

By M. Kataoka, Y. Obara

It is known that compressive strength and tensile strength of rocks vary significantly with specimen size. Rocks are composed of crystals and grains in a fabric that includes flaws such as microcracks, grain boundaries and pores. As the likelihood of including severer flaws becomes greater for a larger specimen, the strengths are small. On the other hand, the size effect in the fracture toughness of rocks has not been made clear until now because there are few studies focused on it. In this paper, Semi- Circular Bend (SCB) test was performed using Kimachi sandstone with various specimen sizes. A shape of the specimen is a semi-circular disc with an artificial notch. The specimens were prepared with various thickness t and radius r as the following two groups; t was changed from 10 to 37.5 mm with r = 37.5 mm in the specimen of group (a), and r was changed from 12.5 to 150 mm with t/r = 0.8 in the specimen of group (b). As a result, there was no significant change in the fracture toughness with different t. On the other hand, the fracture toughness increased with increasing r and converged on a certain constant value in a range larger than approximately 70 mm of r. Consequently it was clear that the size effect in the fracture toughness of the sandstone exists.

Jan 1, 2015

By B. K. Choi, G. E. Kim, S. Noh, T. K. Kim

Oxide dispersion strengthened (ODS) steel has been developed as the most prospective core structural material for next-generation nuclear systems because of its excellent high strength and irradiation resistance. In ODS steel, finely dispersed nano-oxide particles with a high number density in the homogeneous grains can be very attractive to achieve superior mechanical properties at high temperatures, and these favorable microstructures can be significantly changed using process parameters during the mechanical alloying procedures. In this study, the effects of mechanical alloying times on the microstructure of 10Cr-1Mo ODS martensitic steel were investigated. Pre-alloyed powders with Y2O3 powder were mechanically alloyed for various milling times using a high energy horizontal ball-mill apparatus (model: symoloyer CM20). Powder properties such as the mean particle size, size distribution, and crystallite size were evaluated. Uniaxial hot pressing was employed to consolidate the milled powders. The results of a microstructural observation after the MA and UHP processes indicated that the homogeneity of the martensitic structures was considerably increased with the longer milling time. It is thus concluded that the mechanical properties of the ODS martensitic steel are greatly dependent on the mechanical alloying times.

Jan 1, 2015

By Greg Gosson, Larry B. Smith

"These are heady times for the mining industry, with strong metal prices, investor enthusiasm for the junior explorer and ready access to finance for mineral projects. Many projects were shelved in the past because of technical deficiencies — insufficient tonnes or grade, metallurgical problems, the deposit was too deep or too narrow, or the project was physically or economically under water. With the possibility of sustained metal prices, now is the time for those previously “challenged” projects to be re-evaluated and financing sought for continued development. The question is, do these deposits have reasonable prospects for economic extraction, as required by all mineral resource reporting codes? NI 43-101 defines a mineral resource as that portion of the mineral inventory that has reasonable prospects for economic extraction. However, a mineral resource is not simply an inventory of all blocks above a given cut-off grade. The spatial distribution and geological and grade continuity must also be considered. The qualified person (QP) must consider factors significant to project economics at the mineral resource estimation stage, and not just when qualifying mineral reserves. CIM Best Practice Guidelines for estimating mineral resources require the factors significant to project economics be current, reasonably developed and based on generally accepted industry practice and experience. In establishing the cut-off grade, it must realistically reflect the location, deposit scale, continuity, assumed mining method, metallurgical processes, costs and reasonable long-term metal prices appropriate for the deposit. Variations within the resource model (rock characteristics, metallurgy, mining methods, etc.) may necessitate more than one cut-off grade or economic limit in different parts of the deposit model. There must be sufficient knowledge of the metallurgical characteristics of the deposit, which should be supported by preliminary metallurgical test results."

Jan 1, 2003

By Magnus Evertsson, Johannes Quist

HPGRs have since introduced in the 1980s (Kellerwessel, 1993; Schönert, 1988), now become integral comminution units at several minerals processing plants around the world. Even though a lot of the initial issues concerning performance, availability and wear have been addressed and solved there are still phenomena and aspects which can be improved and understood further. Schönert and Sander (2002) presented experimental results and a mechanistic model including the internal force dynamics between the rollers and the compacted bed. They derived expressions for the pressure distribution involving most of the influencing terms and effects. However, in order to solve the differential equations several of the terms vanish by assumptions. The Schönert and Sander model reflects the experimental data in many aspects but the predicted shear force distinctly deviates from the experimental results at the angular position of the peak pressure level. This finding suggests that the particle to particle interaction and breakage process in the different zones seen in Figure 1 are complex and difficult to model using analytical models. A numerical modelling approach using DEM does not require the same amount of assumptions and simplifications of boundary conditions. Hence such modelling may provide further knowledge and vital understanding. In this paper the breakage process is simulated in order to investigate the shear slip behaviour and how it relates to different operating variables. A laboratory scale HPGR corresponding to the experimental setup used by Schönert (2002) have been modelled in EDEM (DEM-Solutions). The bonded particle model (BPM) is used for modelling quartz particles (Potyondy, 2004). The breakage model strength parameters are calibrated against interparticle breakage experiments in an Instron 400RD compression device. The contact model parameters are calibrated using calibration methods developed by Quist (2015). The floating roller dynamics are modelled using a spring-damper system. Results present insights regarding the interparticle slip behaviour as well as the frictional tangential force distribution on the rollers. The simulated roller pressure distribution shows good correspondence with previously reported findings in the literature.

Jan 1, 2016

By L. St-Georges

In aerospace and transportation industries, severe problems are related to fatigue failure. Aluminium is frequently used in these industries to optimize the solidity and minimise the weight of the structures. Nevertheless, the fatigue life of aluminium alloys is limited and specific efforts have to be made to reduce the vibratory stresses in the mechanical parts. When riveted, the life of the sheet metal structures can be increased compared to welded structures, due to the energy dissipated by the friction between the rivets and the sheet metal and the sheets themselves. In the past decade, a new tool was developed to assemble aluminium structures; the friction stir welding. With this new technique, fatigue life of the aluminium welded joints can be increased by a factor from two to ten. However, less energy can be damped by the friction between the components and increased vibratory stresses may occur. In this investigation, the potential of the friction stir welding to create damped aluminium sheet metal structures is evaluated.

Jan 1, 2006

By I. E. Puddington, F. W. Meadus

The beneficiation of barite in mill tailings using an agglomeration technique has been demonstrated. Barite was selectively absorbed from a conditioned aqueous slurry into a collector oil by mechanically mixing slurry and oil. The resulting oil-bonded barite-containing agglomerate was washed, to remove gangue material, and further mechanically contacted with dilute H2SO4 This treatment resulted in the transfer of barite into the aqueous phase. Grades as high as '97% BaSO4, with recoveries of 80%, have been obtained using this technique.

Jan 1, 1973

By D. Seo, P. Au, X. Husang, D. Nagy

The production of single crystal (SX) turbine blades represents the current stateof- the-art in Ni-based superalloy design. With complex casting processes and alloy composition modifications, SX superalloys exhibit superior high temperature mechanical properties to their polycrystalline counterparts. Stresses and plastic deformation can occur in SX nickel-base superalloy engine components at various stages during their manufacture and use. For examples, stresses are created during initial solidification and also during solid state processing such as shot peening, grit blasting, blending, electrodischarge machining and welding. Stresses may also be created during service due to random events such as foreign object impacts. Subsequent exposure of SX to high temperatures during solution heat treatment and brazing repair can result in recrystallization which has been shown to be detrimental to both creep rupture strength and fatigue performance of the components. It is therefore the objective of this paper to understand the recrystallization behavior of two SX superalloys, PWA 1484 and 1483, subjected to pre-stressing and subsequent heat treatments.

Jan 1, 2006

By Du Xinfeng

The resource quantity of the low rank coalbed methane (CBM) accounts for 47% of the total resource quantity of CBM in China. Compared with the exploration and development of the high rank CBM in Qinshui Basin, China and the low rank CBM in Powder River Basin, USA and Albert Basin, Canada, the exploration and development of the low rank CBM are still in the initial test stage. In this paper, on the basis of analyzing the mining geological conditions such as that the Huanglong Jurassic Coalfield is largely situated in the hills and gullies zones, and the coal reservoir has the features such as the low metamorphic degree, large coal seam thickness, simple coal matrix texture, high permeability and small CBM content and so on, it discusses the key technologies such as the development pattern of CBM, well location arrangement, drilling and well completion technology and fracturing technology and so on. It indicates that the underbalanced drilling and the cavity well completion based on the reservoir protection will be the development directions of the CBM development technology in this area.

Aug 1, 2013

Drilling is a common process in mining and petroleum engineering applications which have different objectives. For example, drilling deep boreholes in tight gas formations and gas shales is becoming more popular in the oil and gas industry. By contrast, drilling deep small sized holes for mineral exploration in hard rocks is performed to obtain samples for grade analysis purposes. In both applications optimising the drilling process includes using the most effective operating parameters such as rotation speed and weight-on-bit in order to maximise the rate of penetration. Obtaining the optimum drilling parameters requires sensitivity analysis over a range of data, which would be costly and time consuming during real field operations. Therefore, conducting several experimental simulations in the lab would be very beneficial before field operations begin. A drilling rig was designed and developed to simulate various drilling scenarios. The rig works in conjunction with an existing true triaxial stress cell (TTSC) which is in use for different petroleum related applications. The rig allows drilling into a cubic rock sample of up to 300 mm size. Three independent stresses can be applied to the sample to simulate real in-situ field stress conditions while the sample may be saturated with fluid. A significant feature of the rig is its ultra-high speed rotation which can rotate up to 8000 rpm: this is to simulate hard rock drilling for mineral exploration applications where large weight-onbit could damage the bit cutters. With the proposed design, a drilling fluid of any type can be circulated in the simulated borehole similar to the real situation, to study its effect on drilling performance. The TTSC drilling lid is equipped with torque and drag measurement systems which are two important drilling parameters to be recorded during drilling operation. It is believed that this new drilling rig will open opportunities for performing major new applied research in the area of more efficient drilling in both oil and gas bearing formations and mineral exploration applications.

Aug 1, 2013

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By P. A. Tichauer

Arbitration is a flexible method for dispute resolution that gives control to the disputing parties while still maintaining a clear and well-structured decision making process. It responds to the desires of the parties for a resolution that is fair, binding and enforceable and is guided more by pragmatism, efficiency, effectiveness and equality than by a need to comply with the legal procedures and practices of any single country or jurisdiction. Arbitration is particularly well suited for the resolution of disputes pertaining to international commercial agreements which are often present in the metallurgical sector. This paper provides a simplified outline of the features and advantages of arbitration as well as commentary regarding certain prerequisites in order for arbitration to be binding and enforceable.

Jan 1, 2015

By K. K. Mamyrbayeva, G. Z. Guseinova, V. A. Luganov

This paper presents the results of theoretical and technological studies on leaching ore of Bozshakol deposit. The major oxidized copper mineral of Bozshakol ore is atacamite, and the content of malachite, azurite, cuprite, copper sulfide minerals is insignificant. The chemical composition of the test sample, with mass, %: 0.9 Cu; 55.00 SiO2; 22.40 AI2O3; 9.00 Fe2O3; 2.24 CaO; 3.56 MgO. Technological studies on leaching the ore were carried out with sulfuric acid 5, 15, 25 and 50 g/dm3 in one and multistage (up to 4 stages) countercurrents. Size of ore 1 mm, the ratio S : L 1: 4. It was found that with increasing of acid concentration from 5 to 50 at one-mode leaching the copper extraction reaches 55 %. At multistage leaching the copper recovery reaches 73 %, a productive solution containing g/dm3: Cu - 4; Fe – 1.2; Al – 1.1 at a pH of 2.8. When leaching the cinders obtained by ore roasting in an atmosphere with limited value of oxygen, with increasing of the roasting temperature from 650 up to 750 °? the extraction of copper from the Bozshakol ores reduced from 31.5% down to 24.4%. The rate of filtration is markedly increased compared with the crude ore. When leaching the cinders obtained by roasting in a nitrogen atmosphere a marked increase up to 87.2-88 % of copper extraction from Bozshakol ores is observed. As an extractant for the extraction of copper from the pregnant solution used LIX984N extractant in kerosene. On the basis of the calculations it was built extraction isotherm and modeled processes of copper recovery with the circuit 2E + 1P, allowing up to 93 and 96% extraction. The through extraction of copper from the ore in the electrolyte was 67 %. Technology is recommended for semi test.

Jan 1, 2016

1. Scientific prospecting has had a profound and some-what unexpected effect on the world's supply of raw materials over the past twenty years. Where shortages were recently anticipated, abundance now prevails. It seems probable that, for the foreseeable future, adequate metallic resources will be found at costs well within the world's economic means. 2. The amount of research devoted to scientific prospecting has been extremely small in relation to the possible importance of the problem and to what could be done. It has been dominated by the thought of a dozen brilliant men, and true research expenditures have not amounted to more than a few million dollars. 3. An undue proportion of the expenditures have been for so-called geological research -mostly of a petrologial character. The results have essentially been of historic interest only. However, there has been some in-crease in genetic understanding, and this is of great importance for future resources. 4. Basic advances in mineral exploration have been made in detection techniques, generally called geophysics and geochemistry.

Jan 1, 1964

"Previous studies on the effect of polytetrafluoroethylene addition during chalcopyrite leaching under conditions similar to those of the CESL process have reportedly resulted in complete leaching of the copper without the need for grinding of the flotation concentrate. However, these studies employed a pulp density of only 1% and finely sized PTFE particle that required the use of high impeller rotation rates that are not sustainable at an industrial scale. This paper explores the performance of 1/8” diameter balls of PTFE, that readily sink in the leach solution, on leaching performance at impeller rotation rates and ore pulp densities more typical of industrial practice. Possible routes for separation of the PTFE from the leach residues and their regeneration for recycling back to the leaching stage are also discussed.INTRODUCTIONChalcopyrite, CuFeS2, is the most important primary sulfide source of copper. While pyrometallurgical smelting of chalcopyrite remains the only widely accepted route for treating chalcopyrite concentrates, several medium temperature pressure oxidation processes are claimed to be economically feasible (Muir & McDonald, 2007). Among these, the CESL process has been extensively piloted and demonstrated at the prototype scale. The overall process chemistry of the CESL process may be summarized as follows (Marsden & Wilmot, 2007):4CuFeS2 + 5O2 + 4H2SO4 ? 4Cu2+ + 4SO4 2- + 2Fe2O3 + 8S0 + 4H2O (1)4CuFeS2 + 17O2 + 2H2SO4 ? 4Cu2+ + 10SO4 2- + 4Fe3+ + 2H2O (2)Though copper extractions of over 95 % are achieved, the CESL process requires extra grinding of the concentrate (Muir & McDonald, 2007). This is because leaching is conducted at temperatures around 150 °C, where the elemental sulfur produced is molten and grows thicker on the mineral’s surfaces as oxidation progresses, creating an increasingly large barrier for mass transport. In addition, the sulfur is sticky and tends to cause the mineral particles to agglomerate, effectively halting further oxidation of the particles that end up embedded within the agglomerates. Consumable surfactants, such as ligin sulfonate, have been shown to be effective at avoiding agglomeration, but they are not effective at removing sulfur from the minerals. Hence, their use does not obviate the need for fine grinding."

Jan 1, 2012

By K. Sawamukai, S. Ogasawara, D. Umenai, T. Tsuruta

"Removal of cobalt, strontium or cesium ion from the aqueous solution containing each metal ion only using microorganism was examined. Arthrobacter nicotianae which had a high ability to remove cationic metal ion was used for the removal of each metal. The removal of cobalt, strontium or cesium using A. nicotianae cells was affected by the solution pH, concentration of metal ion, and cell amount. The effects of above mentioned factors on the removal of each metal and time course of strontium from the solution containing each metal only using A. nicotianae cells were reported in this paper. INTRODUCTIONRadioactive elements, such as cesium, iodine, strontium, plutonium, barium, cobalt, lanthanum, yttrium, and tellurium, were detected around Fukushima Daiichi nuclear power plant, which was damaged by the magnitude 9.0 earthquake and the tsunami followed.The removal of radioactive elements from contaminated sources is a worthwhile subject to investigatein terms of environmental control. Research efforts have been especially concentrated on studying microorganisms that remove uranium including bacteria (Andres et al, 1993, Hu et al, 1996, Marques et al, 1991, Strandberg et al, 1981), actinomycetes (Byerley et al, 1987, Friiss and Myers-Keith, 1986, Golab et al, 1991), fungi (Byerley et al, 1987, Galun et al, 1983a, Galun et al, 1983b,Tsezos and Volesky, 1981, White and Gadds, 1990) and yeasts (Strandberg et al, 1981, Schmate II et al, 1978).We have investigated removal and recovery of uranium from aqueous systems using microorganisms isolated from uranium mines. We identified some strains of bacteria with extremely high uranium removing abilities (Sakaguchi et al, 1996), and thus, the microbial biomass may be considered as an adsorbing agent for the removal and recovery of uranium and heavy metals present in aqueous systems around Fukushima Daiichi nuclear power plant.In the present study, we screened various species and strains of bacteria, actinomycetes, fungi, and yeasts for their ability to adsorb uranium (Tsuruta, 2002). Basic features affecting uranium adsorption?co-existing cations and anions, cell amounts, pH, and the adsorption time course?by Arthrobacter nicotianae cells, which adsorbed the largest amount of uranium, were also investigated. In addition, we examined the removal of an other actinoid element, thorium ion, which may be present with uranium in refining effluents.In this paper, the removal of cobalt, strontium, or cesium from the solution containing each metal ion using A. nicotianae cells is discussed."

Jan 1, 2012

By A. Haldar

The major problem encountered in the casting of hypereutectic Al-Si alloys is the stoppage of flow below the rigidity level of solid fraction. In this study, the flow stoppage mechanism was studied using three Al-Si alloys with 14%, 18% and 22% silicon. The horizontal foam patterns used were 12.50 mm (0.50 inch) wide with two section thicknesses 12.50 mm (0.50 inch) and 6.25 mm (0.25 inch) with a common sprue. The primary silicon distribution along the length of the casting was studied to determine the mechanism of flow stoppage. It was found that the surface of the flow tip of Al-14%Si alloy was smooth with a few undulations. As the silicon level increased, undulations at the flow tip increased. The number and size of undulations were maximum for the Al-22%Si alloy. Microstructural analysis using optical image analyzer revealed that the flow tip consisted mainly of eutectic silicon in the aluminum matrix and a few primary silicon crystals (PSC). The PSC were in the interlocked condition few centimeters behind the flow tip. It was also found that the gap between the flow tip and the PSC concentrated area increased with an increase in silicon level. Phase characterization was done with SEM-EDX to identify the precipitating phases.

Jan 1, 2007

By D W. MacFadgen

THE operating advantages of the longwall retreating system of mining, as opposed to longwall advancing, have been well known for many years. Although retreat walls have been successfully worked in the past in some of the collieries of the Dominion Steel and Coal Corporation in the Sydney, Picton and Cumberland areas, the adoption of longwaIl retreating as the general sys-tem of mining has not been attractive in the Sydney field, due to the time and expenditures required to drive roadways to the boundary. In addition. difficulties in maintaining effective ventilation on the faces, especially under conditions of low barometer, have made the operators in the field hesitant to adopt this as the general system of mining. The development of a machine capable of rapid entry drivage has made possible the driving of the necessary road ways to the boundary at a moderate cost, completely changing the picture and making a retreat system more attractive.

Jan 1, 1961