Search Documents

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed.The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grade, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the final cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure I."

Jan 1, 1995

By J. C. Taylor, J. A. Davis

"Existing environmental, health and safety regulations have forced pyrometallurgical facilities worldwide to drastically change some of their traditional methods of operation. In extreme cases, a number of facilities have been closed due to their inability to conform to these existing regulations. Tougher future legislation and government policy will lead to more stringent regulations and enforcement policies. The efficient control of smelter secondary emissions will, therefore, become critical to successful smelter operation.Much attention has been paid to the smelter primary process off-gas systems, including the development of new process designs to reduce the number of uncontrolled transfer operations. However, even the most modem smelter design requires control of its secondary contaminant sources, which mayor may not be directly related to the process operation.This paper discusses some of the potential secondary emissions encountered in many of the present process technologies. A few of the emission sources presented are only periodic in nature, such as those caused by maintenance procedures, but which have the capability of forcing smelter shut-down because of their direct impact on worker health and safety. The paper deals with a variety of topics relating to the efficient control, maintenance and monitoring of secondary emissions in copper, nickel, aluminum, magnesium and lead smelters, as well as in iron foundries and steel making facilities. Examples of the typical problems encountered in each of the above process operations are presented, including fume control at furnace tapping and slagging locations, metal transfer stations, tapping launders, and ladle transfer operations. The parameters for the most efficient design of fume capture systems, problems encountered with the handling and clean-up of certain collected emissions, and examples of successful solutions in particular operations are discussed."

Jan 1, 1994

By John Galbraith, Dwayne D. Tannant, Chris C. Langille

"Development of underground openings in a deep mining environment requires a support system that is able to absorb energy as a result of dynamic loading due to rockbursting and blasting and static loading due to convergence as the development face advances. The support system must be resistant to corrosion and be effective over the life of the excavation, upward of ten years, yet simple and cost effective to install. Over the past two years, research has been conducted at INCO’s Creighton Mine to try and identify a one-pass grouted support system that will meet these needs.The main problem faced, with simply using grouted rebar at depth, is the effect of tunnel convergence on the stiff grouted bolts. Typically, if fully grouted, stiff rebar are installed to the face of an advancing development heading, the amount of convergence that occurs can result in failure of the bolts at the face plates used to attach the mine screen to the back. An initial support is required to enable crews to continue the bolting cycle in the immediate term, yet allow for this convergence over the longer term as the drift advances. The ideal support system will allow both to occur, giving effective immediate support while providing long-term effectiveness in allowing convergence to occur while maintaining the capacity of the bolt.This paper will investigate the expected convergence in deep development headings at +2200 m (+7200 ft) through the use of direct measurements using both flex rod extensometers grouted into the back of a development heading and five-point tape extensometer stations. Measured results will be compared with simple2-D numerical analysis to evaluate the anticipated convergence expected to be absorbed by the bolting system. The required convergence will then be compared with load deformation response of several support configurations."

Jan 1, 1996

The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members Ñ the Universities of Queensland and Sydney and the CSIRO1, and by its industry members Ñ BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining.

Jan 1, 2001

By CIM Standing Committee

The CIM Definition Standards on Mineral Resources and Reserves (CIM Definition Standards) establish definitions and guidance on the definitions for Mineral Resources, Mineral Reserves, and mining studies used in Canada. The Mineral Resource, Mineral Reserve, and mining study definitions are incorporated, by reference, into National Instrument 43-101 – Standards of Disclosure for Mineral Projects (NI 43-101). The CIM Definition Standards can be viewed at mrmr.cim.org. Readers should be aware that reports written by persons issuing technical reports that disclose information about exploration or other mining properties to the public in Canada are governed by a number of securities regulations.

May 10, 2014

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By Royston Colbourne

Objectives Of Presentation - Identify specific risks - A fresh look at risk - Provide a moment reflection on risk - Open discussion on risk A route to solution and advanced thinking.

May 1, 2010

By A. Bauer, P. Katsabanis, M. Baker

The principal results from a previous paper presented at the Mine Accident Prevention Association of Ontario in 1987 (1) are summarized here. It is concluded that the selection of explosives in mines experiencing sulphide ignitions is important and that aluminized explosives should be avoided because of their high explosion temperatures and their detonation products. The duration of the blast is also critical and secondary blasts should not occur simultaneously with nearby priroa:ty blasts.

May 11, 1988

By P. Nayak

"Comminution is an energy intensive and expensive process consuming approximately 40-50% of the total processing costs in a mining operation. This process poses an even greater challenge with gold ores due to their low elemental concentration and small particle size. Over 99.9% of the ore fed to the mill is waste which must be removed during the ore processing stage. Preconcentrating the Run of Mine (ROM) ore before feeding the mill will result in significant cost savings. In partnership with Sacré-Davey Engineering, Agnico Eagle Mines Limited identified this opportunity and is currently evaluating the implementation of sorting technology to preconcentrate the ore or upgrade the waste material at its operations. This paper will discuss the steps adopted by Agnico Eagle in the evaluation and installation of sorting technology at its operations. Since the Company has a large portfolio of operations, the first step in the project was to shortlist the operations that had the highest probability for successful application of the technology. Following this, the top three operations were selected for bench scale evaluation. The projects which showed the most economic potential were then considered for detailed evaluation and pilot plant installations. This paper provides an insight into the methodology followed by Agnico Eagle and Sacré-Davey in the evaluation of the technology.INTRODUCTION The benefits of ore sorting technology are being increasingly understood by the mining industry today. The application of ore sorting in gold mining is attractive due to the nature of the mineral distribution. The presence of high value minerals distributed in an extremely small mass of the ROM ore creates a tremendous opportunity for preconcentration with ore sorting. Since Agnico Eagle currently has a portfolio of eight operating mines and numerous development projects and exploration properties, the challenge was to identify the deposits which had the most favourable mineralogy and grade distribution for successful ore sorting. The success of ore sorting is mostly based on the minerals present in the deposit and the grade distribution. The minerals signify the amenability of the deposit for ore sorting and the kind of sensing technology to be used. On the other hand, the grade distribution demonstrates the amount of material that can be rejected without losing value. In order to understand a deposit’s characteristics, it is important to examine the sample’s behaviour with various sensors and then assay it to know its actual value. It is a common practice in the mining industry to document assay value of drill cores and/or material feeding in and out of the mill. However, those VALUES (are insufficient to understand the grade variability on a granular basis. To capture the ore variability in very high resolution and significantly improve the selectivity of the material feeding the mill, it is vital to assay the samples on a rock-by-rock basis, as this is the level of resolution which will be examined by the ore sorter during sorting. A careful and elaborate procedure was followed in evaluating the technology at Agnico Eagle’s operations which is discussed in this paper."

Jan 1, 2019

By T. Johnson, D. Kelley, J. Graham

"Hydrometallurgical processes can be exceptionally corrosive. Conditions associated with metal extraction and refining require materials of construction that can withstand process acids and acid chlorides at temperatures up to 90°C (194°F). Process vessels, piping, scrubbers and ducting can be rapidly compromised in these aggressive environments if not designed with care. Design engineers are challenged to find materials that can stand up to hydrometallurgical processes especially for copper, zinc, nickel, cobalt and uranium. This paper will evaluate material solutions to determine which provides attractive economics for initial procurement as well as high durability for reasonable life cycle costs.INTRODUCTIONMining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel cobalt and uranium have been particularly active.The world’s largest nickel mine – the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale’s Voisey Bay mine in Labrador. Voisey’s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $858 Million Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 – 250,000 MT/yr manganese carbonate.High nickel alloys and rubber lined steel have been used for decades to design corrosion resistant equipment for mineral processing environments. These materials demonstrate reasonable resistance to corrosion for most environments. Unfortunately, higher nickel alloys are quite expensive. Rubber lined steel is a bit more affordable but requires continuing service over time which ultimately drives up its cost as well. FRP (Fiberglass Reinforced Plastic) has also been used extensively in mineral processing for tanks, piping and ducting employed in aggressive environments. Today, more and more design engineers and material specifiers are calling for FRP composites for both new and replacement equipment used in the refining and processing of a variety of metal ores."

Jan 1, 2012

By I. V. Kojo

Continuous development of technologies has been self-explanatory for Outokumpu Technology's engineers for decades. The aim in the development has always been the improvement of profitability of the copper production but also the sustainability of the processing i.e. high copper recovery, low external fossil based energy utilization, high emission captures and of course low operation and investment costs. Outokumpu Technology's long-term view of the development is a change towards continuous processes and elimination of number of unit operations in smelting i.e. elimination of possible sources of emissions. Outokumpu blister smelting processes i.e. Outokumpu Direct-to-Blister Flash Smelting and Kennecott-Outokumpu Flash Converting have shown excellent operational results during the years of operation and it is expected that soon more than 10 % of the world primary copper is produced by these technologies. The paper will give some background of this development trend.

Jan 1, 2007

By T. Feldmann, G. P. Demopoulos

The feasibility of chloride leaching processes depends on interfacing them with cost-effective HCl regeneration technologies. This paper summarizes the most important findings of research conducted in the past 3 years concerned with a novel process to regenerate high-strength HCl from concentrated CaCl2 solutions at temperatures below 100°C, via reaction of CaCl2 with H2SO4 resulting in the formation of calcium sulfate phases (gypsum, a-hemihydrate or anhydrite). From constant supersaturation semi-batch experiments in pure solution it was found that the crystal growth rate of hemihydrate, and hence the particle size, was influenced by the rate of reagent (Ca2+, SO4 2-) supply to the reactor. Additionally, growth studies of DH in presence of impurities (K+, Mg2+, Sr2+, Ba2+, Fe2+/3+, Al3+, La3+, Y3+, F- and PO4 3-) showed that specifically Sr2+ and PO4 3- are taken up during crystal growth. Furthermore, it was found that decreasing water activity (via different HCl/CaCl2 concentrations) and increasing temperature reduce the metastable life-time of DH and HH by increasing the phase transformation speed. The DH/HH transformation was identified to be dissolution-precipitation based, while HH to AH is a topochemical process. Finally, continuous experiments on bench scale are underway to confirm the feasibility of the process to obtain super-azeotropic strength HCl with up to 9 mol/L (~30wt.%) from 5 mol/L CaCl2 (~40wt.%) solution.

Jan 1, 2014

By V. T. Panayotov, M. I. Panayotova

Wastewater from mining and mineral processing activities is often polluted by anion forming metals, such as molybdenum and chromium. Low cost materials, including zeolites, are studied for removing heavy metals from wastewater. It is widely accepted that natural zeolites are not effective in removing metals in anionic form. The paper presents study on use of metal modified natural clinoptilolite to remove Mo (VI) and Cr (VI) ions from model soft wastewater. Modification with Pb, Fe(III), Zn and Ba increases clinoptilolite uptake capacity with respect to Mo(VI) at low pH values of the water subjected to treatment, the efficiency decreasing in the order Pb > Fe(III) > Zn > Ba. Only lead-modified clinoptilolite shows high uptake of Mo(VI) in acidic, neutral and slightly alkaline conditions. Modification with Pb, Ba and Fe(III) increases zeolite uptake capacity with respect to Cr(VI) from neutral water. The effectiveness of Ba-modified zeolite decreases in slightly acidic water. Over 90 % uptake of initially available Cr(VI) is achieved by lead-modified clinoptilolite both under neutral and slightly acidic conditions. Increasing the initial pollutant concentrations increases the removed amount both of Cr(VI) and Mo(VI) for Pb-modified clinoptilolite. The findings could be a basis for using the natural clinoptilolite to remove in consecutive steps: firstly Pb(II) and/or Fe(III) ions and then loaded zeolite to be used for Mo (VI) and/or Cr(VI) removal. The kinetics of Mo(VI) uptake by CL-Ba, CL-Fe(III), CL-Pb, and CL-Zn is best described by the pseudo-first order kinetic equation. The kinetics of Cr(VI) removal by CL-Ba, CL-Fe (II), CL-Fe (III) and CL-Zn is best described by the pseudo-first order kinetic equation. Kinetics of Cr(VI) removal by CL-Pb obeys the equation for the first order irreversible reactions. Finding way to remove anions-pollutants from the mineral processing wastewater will render this industry more environmentally friendly and socially acceptable.

Jan 1, 2016

By Michael Cullen

The Quinsam Coal Mine is in the process of extracting a panel beneath the mine access road. To prevent damage to the road, and adjacent powerline, it was necessary to establish a ?protection zone? within which the extent of mining would be limited. The protection zone is analogous to the setback limit. For economic reasons it was desirable to make the protective zone as small as possible, and with the greatest extraction ratio possible. The size of the protective zone was established by determining the angle of critical deformation using the numerical model FLAC, coupled with field data on subsidence from the Mine. The angle of critical deformation (defined as the angle, measured from the vertical, at which intolerable damage is sustained by a structure) was determined to be between 0 and 5 degrees. The allowable extraction ratio in the protection zone was established using the ARMPS method of pillar design coupled with field data on pillar stability from the Mine. Excavations spans to prevent caving were determined by historical experience and field data on span stability from the Mine, coupled with numerical modeling. The minimum pillar size was determined to be 7.5m. The maximum pillar height was established at 2.5m. The maximum allowable excavation span was determined to be 8.5m. With these criteria, extraction ratios between 54 and 73% (measured in plan view) were determined to be appropriate for the protection zone.

May 1, 2001

By J-S. Marois, F. Cappucitti, Y. Dodier, D. Downey, G. Matton

"The flotation processes of the Niobec Mine have been affected by a seasonal loss of recovery and a significant increase in reagent consumption over the past few winters. This paper discusses the problem-solving methodology that was used to identify the root causes, to develop solutions and to implement changes that resolved the problem to restore the process to summer-like conditions year-round. Mainly, it was found that the process water was contaminated by phosphates ions, which adversely affected the carbonate pre-flotation, and caused detrimental effects on the subsequent niobium flotation. The phosphate ions were being generated by the process itself, but were consumed by algae in summer conditions. It was determined in laboratory studies that concentrations as low as 5 ppm were enough to affect the circuit and that the multiple additions of process water throughout the circuit was worsening the effect. Also, temperature was found to have an impact on the reagent performance. The performance of the plant was restored by implementing a natural treatment of our process water with a simple cost-free rearrangement of our circuit streams. In addition to that, our extensive geometallurgical program was used to provide ore to the plant restricting phosphate generation in the process. Also, a modification of the collector was developed and introduced in the carbonate pre-flotation that provided improved performance during the periods of low pulp temperature.INTRODUCTION Niobec is one the three major global producers of niobium presently in operation. Situated in the Saguenay-Lac-St-Jean region of Quebec and in operation since 1976, the site produces ferroniobium (FeNb) to be used mainly in High Strength Low Alloy (HSLA) steel, which is known to have better mechanical properties than carbon steel. The Niobec operation consists of an underground mine, a concentrator and a converter plant. The concentrator concentrates niobium-bearing minerals, mainly pyrochlore and columbite, to produce a high-content Nb2O5 concentrate which is then converted to FeNb in the converter plant by an aluminothermic reaction. The Niobec concentrator flowsheet, which has gone through many expansions and optimisation over the years, consists of grinding, desliming, flotation and leaching steps. The flotation steps are numerous, sensitive and difficult to operate due to the non-selective nature of oxide mineral collectors. Thus, the pyrochlore concentration process at Niobec still faces many challenges and is constantly going through periods of continuous improvement."

Jan 1, 2018

By Farzad Khodabakhshi, Adrian P. Gerlich

"In this article, cold spraying process was utilized to coat the surface of AZ31 magnesium alloy with a layer of AA7075 aluminum alloy. Thereafter, friction-stir processing (FSP) was employed to enhance the microstructure and consolidate the deposited layer. The grain structure and phase morphology were studied along with indentation hardness before and after cold spraying and friction stir processing. The magnesium substrate had an initial hardness of 74 HV which increased to 102 HV after FSP due to refinement of grains to <2 µm. The aluminum coating layer, provided improved surface hardness up to 160 HV, which further increased to 173 HV after FSP was applied.INTRODUCTION Cold spray is a material deposition process which can be used for surface modification, since it deposits material on a metallic substrate with little heating by way of high velocity ballistic impacts. Using cold spray technology, it is possible to deposit a wide range of coatings with various thicknesses by controlling the characteristics of the feeding powder and metal substrate, gas temperature, gas pressure, powder feeding rate, nozzle geometry, and gun traverse velocity. This process has been recently employed for surface modification in various aircraft and automobile structural applications. This has led to a broad range of research using this process for production and modification of different metallic and non-metallic systems. In the present study, cold spray process was used to deposit a uniform layer of aluminum-zinc alloy (AA7075) on the surface of AZ31 magnesium alloy. This coating was subsequently treated by way of friction-stir processing (FSP) as a new post-spraying modification technique to enhance the structural homogeneity and densification of the coated aluminum layer. This method utilizes a non-consumable rotating tool with a specially designed shoulder and pin that is plunged into the surface of metal to be modified and then moved along the direction of interest. The localized frictional heating between the rotating tool and workpiece leads to softening of the materials around the pin, and material extrusion through a complex flow of material from the advancing toward the retreating side the tool. To the author’s best knowledge, only a few reports discuss the modification of a cold sprayed deposit by FSP process. The microstructure and mechanical properties of the cold sprayed layer and substrate before and after FSP modification were examined using optical observations (OM) and indentation hardness testing. Furthermore, the AZ31 alloy substrate alone was treated with FSP as well, for the aim of comparison to the processed coating."

Jan 1, 2017

By Henry C. Knight

A number of improvements in the techniques of budgetary control have been developed in the 1970&apos;s. The most significant of these is zero-base budgeting. This procedure is a marked improvement, because it overcomes some of the key weaknesses inherent in most traditional approaches to budgeting. It incorporates techniques and disciplines which improve the quality of both the budgeting effort itself and the documents that most senior managers will need to evaluate. The end result is a budget that establishes and improves cost effectiveness. This budget is based on resource allocations using cost-benefit criteria and on a system of prioritization for making funding choices. Zero-base budgeting is applied only to costs and expenses that are not conducive to control using industrial engineered standards. Therefore, the benefits attributed to zero-base budgeting will only hold true for administrative, selling, exploration, safety, fire protection and overhead, and other indirect types of costs and expenses. It is in this context that the question of its attractiveness for the mining industry is dealt with.

Jan 1, 1978

By K. Huang

"Solvent extraction (SX) is one of the most effective techniques for the multi-metal separation. However, repetitive pre-treatment of feed-in solutions and/or multi-steps two phase equilibrating in conventional SX processes were always unavoidable due to the poor separation selectivity between those metals with similar physicochemical properties. In this paper, our recent efforts, aimed to develop a “Three Liquid Phase Extraction” (TLPE) strategy for one-step separation and selective enrichment of different metals respectively into three coexisted liquid phases, are reviewed. Various feasible “Three Liquid Phase Systems” (TLPS) are evaluated. The TLPE technique provides a potential possibility for multiphase extraction to separate multi-metals.INTRODUCTIONLiquid-liquid Solvent Extraction (SX) is one of the most effective techniques for metal separation and purification. Traditionally, extraction and separation of multiple valuable metals from the leaching solutions of complex ores, industrial wastes and byproducts have to face such difficulties that multiple target metals with similar physicochemical properties co-exist in the solutions, and therefore their mutual separation selectivities are very poor. In conventional organic-water two phase SX processes, repetitive pre-treatment of feed-in solutions including the adjustment of the solution acidity, removal of impurities and/or multi-step liquid-liquid two phase equilibration were always unavoidable (Wang and Chen, 2001). Only one of the target metals is obtained in each extraction step, therefore the whole separation processes for multi-metal separation are typically very long and costly.Liquid-liquid-liquid three phase extraction is a developing technique for separation of complex systems containing multiple target components (Tan, 2003; Shen, 2006; Yu, 2009). The technique is in fact a three-liquid-phase selectively partitioning of different target components through the control of phase-forming behaviors of extraction system to create a unique separation medium with three co-existed liquid phases. The separation selectivity of “Three-Liquid-Phase System” (TLPS) may derive from its three-layered liquid phases from up to down with different hydrophobic or hydrophilic environment, and therefore each phase has its own specific selectivity for dissolving of an individual component. In a well designed “Three-Liquid-Phase System” (TLPS), multiphase extraction and selective separation of different components respectively into three different liquid phases can be achieved by only one-step of extraction. Owing to its distinct advantages, “Three-Liquid-Phase Extraction” (TLPE) technique has found many potential applications in purification of various organic chemicals (Shen, 2007) and biological activities (Chen, 2002; Tan, 2006; Jiang, 2008), treatment of environmental wastewaters (Shen, 2006; Yu, 2009; Yu, 2010; He, 2012), extraction of valuable components in natural products (Liu, 2010) and separation of multi-metals in complex leaching solutions (Jin, 2009)."

Jan 1, 2012

By WENDY MARTIN

The Eastern Townships and Asbestos Hill areas are the current asbestos-producing districts of Quebec. Mining in the two areas began in the /are 1870s and 1972 respectively. Production from the Eastern Townships is derived from rhe Serpentine Zone of ulrramafic rocks, specifically from basal serpentinized peridotite members of what are now considered to be allochrhonous ophiolitic material that was abducted onto the Early Ordovician continental margin. From south west to northeast, the rhree allochthonous asbestos-producing sections of the Serpentine Zone are designated the Asbestos Ophiolite Complex, the Thetford Mines Ophiolite Complex and the Pennington Dyke; the Pennington Dyke is considered to represent a segment of serpentinized Alpine peridotire that was fragmenred from a larger, more complete ophiolire complex. The Asbesros Hill deposir on the Ungava Peninsula lies in what apparenrly is an inrrusive sill found wirhin rhe Chukorar Group, the uppermosr group of Precambrian-aged Cape SmithWakeham Bay Belr of volcanic-sedimentary rocks.

Jan 1, 1984

By M. Tardif, F. L. -Lavoie, M. Ruel

"In mineral processing, it is often very difficult to reliably measure several key operation variables. The harsh environment and high temperature encountered in pyrometallurgy processes lead to some difficulties when selecting the instruments, valves and actuators. If an important variable cannot be measured or manipulated adequately, controlling it can really become a big challenge. Sometimes, it is simply impossible to find the perfect equipment for the task. To help overcome these difficulties, a different approach is required. This approach will not correct the inherent problems related to the instruments and valves, but will cope with these problems. This article will demonstrate how modern process control techniques can be used to solve complex problems while remaining easy to implement. In this article we will described how soft sensors and multivariable fuzzy logic control were implemented at Koniambo Nickel to stabilize the furnace feed and allow for safe and reliable operation of an 80 MW DC arc furnace.INTRODUCTION Process Overview The process plant at Koniambo Nickel SAS is located in the North Province of New Caledonia, 310 km north of Noumea. The nickel-bearing ore is mined in the nearby Koniambo massif. After being screened and crushed, the ore is transported to the processing plant using a 12 km conveyor. After stacking in two blending piles, the ore, containing 2.3% nickel, is fed to the processing plant where it will go through the NST process (Nickel Smelting Technology) before being sent to refining and shotting. This article will focus on the improvement to control of the NST processes. The first steps of this process consist of milling the ore and removing all moisture through calcining (Figure 1)."

Jan 1, 2017