Search Documents

By G. O. Crowell

This paper gives the history of the celestite deposit, now being mined by Kaiser Celestite Mining Ltd., near Sydney, Nova Scotia. Mining and milling procedures are covered, and the regional and local geology of the area are described, including the origin of the celestite.

Jan 1, 1971

By I. A. Menshikh, S. A. Kotov, N. L. Shinkarkin

All the cycle for conversion of natural and reprocessed uranium of ROSATOM’s “TVEL” Fuel Company is concentrated at the Siberian Chemical Plant. Conversion capacities are located on two sites, i.e. the Radiochemical Plant, which refines feedstock, and the Conversion Plant, which produces uranium oxides and uranium hexafluoride. Liquid radioactive waste arising in the process, after pretreatment, is transferred to a dedicated national operator for underground disposal. Environmental strategies pursued by the Fuel Company involve the introduction of process solutions intended to eliminate liquid radioactive waste and convert it into a solid phase. In the 5–7 years coming, work will be performed to refurbish and upgrade conversion facilities of the Siberian Chemical Plant that will principally change its radioactive waste management scheme. This paper describes the current waste management scheme and sets out planned schemes for management of natural and reprocessed uranium waste, which will be implemented in the refurbishment of conversion facilities of the Siberian Chemical Plant. The new technologies for the management of liquid radioactive waste from uranium conversion described in the present paper have an undeniable advantage over the current technology mainly due to significantly less environmental harm.

Jan 1, 2020

By R. Cottam

The deformation and recrystallisation of magnesium yttrium alloys containing 0.23, 0.84 and 2.71wt% yttrium and commercially pure magnesium extrusion has been investigated at temperatures between 200 and 350°C. The alloys were produced as billets 7.5 cm diameter, solution treated at 525 °C for 8 h and extruded into 3 cm diameter bar at 390°C. Channel die compression was employed to deform the samples at a strain rate of 1x10-3s-1. For the 0.23 wt% yttrium alloy and the pure magnesium, dynamic recrystallization (DRX) occurred at all temperatures and the amount of DRX increased as the temperature was raised. In the alloys containing 0.84 and 2.71 wt% yttrium DRX was almost completely suppressed at all temperatures. The absence of DRX in the 0.84 and 2.71 wt% yttrium alloys was accompanied by a decrease in the ductility, except at 350°C the highest deformation temperature. It was observed that this increase in ductility was accompanied by a reduction in deformation twinning and the initiation of pyramidal slip. This work highlights the important role that DRX plays in enhancing the ductility of magnesium alloys.

Jan 1, 2006

By M. Mahfoud

The effect of grain refinement on the tensile and fatigue crack propagation behavior of sand cast magnesium alloy AM60B has been investigated in the present study, C2Cl6 in the amount of 0,3% was used to grain refine the melt, The fracture toughness tests were conducted in laboratory air at room temperature (25°C) using a sine-wave cyclic frequency of 20Hz and a load ratio of R = 0,1, The response in the Paris's regime and the critical stress range were determined, Preliminary findings have shown that C2Cl6 has a significant effect on both the tensile properties and fatigue crack propagation of the alloy tested, Grain refinement increased both the yield and ultimate tensile strength by more than 46%, and decreased the crack growth rate from 2,7 to 1,4 MPa Vm , However, the grain size seems to have a smaller effect on threshold stress intensity factor range. The fracture surfaces of specimens were examined optically and under the scanning electron microscope (SEM) to determine the relationship between grain size and fatigue properties.

Jan 1, 2005

Despite the claims of energy efficiency and the considerable development that has gone into dramatically extending rolls? life and facilitating rolls? change-out, in the six years since the last SAG conference, only a few HPGR operations have entered the realm of mineral processing. Risk barriers to the take-up of new equipment or processes are: a massive increase in materials handling issues as well as in the number of pieces of equipment required, low total circuit potential energy savings, and similar or higher capital costs. An alternative route is to make use of the complementary strengths of the HPGR and SAG in hybrid circuits. Minimising materials handling issues, providing an ideal balanced feed to the AG or SAG mill, and improving controllability through shifting grinding load as the RoM feed changes, are all potential major advantages to this approach. Conceptual circuit layouts, based on real measured ore and equipment data, are presented here to illustrate the potential production upside, the reduction in operating costs and the reduction in the physical and energy footprints.

Jan 1, 2012

By M. Aljarrah

The phase equilibria in the Mg-Al-Ca system was investigated experimentally by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) techniques similarly the Mg-Al-Sr system has been studied using DSC and XRD as well as scanning electron microscopy/energy dispersive spectrometer (SEM/EDS) and quantitative electron probe micro-analysis (EPMA). A new ternary solid solution MgxAl4,xSr was confirmed in Mg-Al-Sr system, which is a substitutional solid solution of Mg atoms in Al4Sr. Maximum solubilities of 21.3 at.% Al in Mg17Sr2 and 11.4 at.% Al in Mg were observed. It was also noticed that Mg38Sr9 dissolved 12.5 at.% Al. In the Mg-Al-Ca ternary system, one of the invariant transformations predicted by thermodynamic modeling was verified experimentally and found to occur at 512°C with composition close to 10.8 at.% Ca, 79.5 at.% Mg and 9.7 at.% Al. A ternary solid solution (Mg,Al)2Ca was confirmed where large solid solubility of Al in Mg2Ca was observed.

Jan 1, 2006

By M. D. Gerst

The degree to which copper will continue to be in an integral part of the world economy in the future will depend largely on the dynamics of global economic development, the primary and secondary copper resource stock, technological change, and potential environmental constraints. We have characterized the copper cycle of 1994 for all of Earth's regions and for the planet itself (T. Graedel et al., Environmental Science & Technology, 38, 1242-1252, 2004) and recently updated that cycle to year 2000. In this paper, we compare various features of the 1994 and 2000 cycles. The three largest-using regions, Asia, Europe, and North America, all increased their absolute rate of copper use between 1994 and 2000, and all increased the per-capita rate of copper use as well. Globally, the use of copper increased by about 32%, from 11.7 to 15.3 million metric tons, while population increased by only 8%. Various changes are seen in scrap trade, finished products trade, and other parameters of the cycle. We conclude by considering how the rates of technological change and growth in demand, especially in Asia, may influence the copper cycle in the years ahead.

Jan 1, 2007

By Allan P. Fawley

ONE hundred miles from Vancouver, at an elevation of 4,000 feet, is the Pioneer mine. It is situated on Cadwallader creek, a tributary of Bridge river, and is reached by travelling from Vancouver to Squamish by boat, a distance of thirty-two miles, from there by train to Bridge River (one hundred and seven miles), and finally by automobile across Mission mountain .(7,000 ft. elevation) to the mine (fifty-six miles): a total distance of one hundred and ninety-five miles. Prior to 1924, many Companies had examined the Pioneer, which had been developed by shaft to a depth of 200 feet, but, while values were good, the small size of the ore-shoot discouraged large investors. In July, of that year, opera-tions were re-commenced by the late David Sloan and, on sinking further, the ore-shoot was found to lengthen greatly as well as to ex-tend in depth, while remarkable gold values also were encountered. When, later, the price of gold rose from $20 to $35 per ounce, the mine was in an excellent position to take full advantage of the increase + and not only became an extremely profitable enterprise itself but its success greatly stimulated the search for and development of other 1-gold properties in British Columbia.

Jan 1, 1937

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012

By L. Bichler

Lightweight magnesium alloys are gaining in popularity for applications in the automotive and aerospace industries, Their use, however, remains limited due to their relatively low strength and creep properties. Lost Foam Casting (LFC) is a new casting process and the strength of foam cast magnesium alloys has not been investigated in great detail thus far, In this research, magnesium alloy AZ91 E and three new alloys were cast by the LFC process to study the effect of varying aluminum and manganese content on the alloy's tensile properties, The study reveals, that the tensile strength of the magnesium alloy is closely related to the relative amount of aluminum in the system. Formation of ß-Mg17Al12 phase was seen to significantly affect the yield strength and ductility of the alloy, Furthermore, formation of manganese intermetallic compounds was seen to effectively increase yield strength of the base alloy, Individual alloy morphologies were analyzed via optical and SEM techniques.

Jan 1, 2004

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The project implementation phase, FEL4, is generally a complex undertaking. The project has been approved for construction and the capital has been allocated. At this point the project team comes under significant pressure to meet the safety, schedule, cost, and start-up committments. For the design team the principal tasks are to finalize detailed design, complete procurement, and issue construction contracts. Design activities must be closely coordinated with equipment and material procurement. A clear engineering plan should be based on well-defined work packages to meet construction, commissioning, and startup requirements. A range of review processes by discipline, area, and third parties assure quality. Constructability, safety, and hazard reviews are performed throughout the design process. Three-dimensional models that incorporate extensive databases help to maximize efficiency and minimize errors. Well-managed projects have a clearly accountable design team, rigorous change control processes, and well-defined workflows. Key individuals from the design team participate in commissioning, operator training, and startup.

Jan 1, 2015

By S. Kivrak

The firms in construction industry could not sufficiently adapt the rapidly emerging information technologies in recent years into their corporate structures. Therefore, in an effort to further exploit the benefits of information technology (IT), integration of the experiences and backgrounds of construction industry and the advantages of IT, is one of the most open-ended fields for improvement in this industry. Utilization of IT in the construction sites will positively affect the efficiency, productivity, quality and health & safety issues in the construction sites thus the cost and completion time of the projects. Within this context, augmented reality technology, which brings a new perspective into IT, can be put into the service of construction industry. Augmented reality which has been designed to improve the services in many application domains such as school education, military warfare, military trainings, industrial maintenance, retail and medical, can be defined in the simplest form as augmenting the real world with information from the virtual world. The main aim of this study, which presents an overview of an ongoing project, is to develop an innovative method by making a construction worker, foreman, equipment operator or a site engineer watch a very comprehensive and informative animation which will enable the said staff to perform or supervise all the phases of the activity he or she is in charge for in a more efficient, productive, safer and qualified manner by means of smart glasses using augmented reality systems. In this respect, training material related with the activities in the construction sites will be prepared and with a well-fictionalized scenario, animations exhibiting all the phases and details regarding the related activity (e.g. masonry, formwork and rebar works etc.), method of statement, correct and incorrect applications in comparison-wise manner, will be produced. Therefore, the user will be able to reach the training material, method statements etc. in the animations about the activity he or she is in charge for, enabling him or her to figure out the work as prescribed in the specifications. Basic trainings about the system will be given to target group, i.e. construction workers, foremen, operators, site engineers and managers working in the construction sites to apply the system on sites after all the system was tested. After the testings, to determine the effectiveness of this system, semi-structured interviews and survey questionnaires will be conducted among the mentioned target group. Therefore, the potential benefits of this system to the construction industry can be determined. The main target of this study is to implement an efficient, thorough construction management by orienting the staff in the construction sites to perform efficient, safe and qualified works by means of smart glasses that use augmented reality. There are relatively few studies about the implementations of augmented reality technology in construction. The outputs to be attained in the end of the study have the potential of improvement of time, cost, quality and safety parameters by ensuring a qualified, safe, efficient and productive construction management via augmented reality technology in the construction industry.

Aug 1, 2013

By G. Shore

"The development of a DC resistivity instrumentation system for data acquisition in extreme topography yielded an unexpected bonus in the quality and information content of the type of raw data gathered. Not only were traditionally too-rough areas being investigated systematically for the first time, the unique high-density, multi-directional raw data were providing the opportunity to greatly expand the range of conductive and resistive signatures that could be accurately recognized. Using a true 3-D inversion algorithm, 3-D earth resistivity imagery began to show distinctive anomaly patterns for hydrothermal mineralization at the seldom-visited resistive end of the spectrum, successfully imaging epithermal gold systems in conditions that had defied conventional ground and airborne geophysics for years.The traditional mode of designing a resistivity survey to test a specific target concept was shown to be an unnecessary limitation on exploration thinking when a single sweep acquisition of dense, multi-directional 3-D raw data could effectively provide the all-targets “shotgun” coverage that would take 10 or 12 conventional surveys to duplicate. Exploration planning has the opportunity to move from single steps of trial and error geophysical testing to a mode of mapping everything at the outset, and then sorting out what might be of exploration interest in the results. Survey parameterization becomes the non-technical process of marking an outline on a map and declaring “survey here.” Operational and interpretational reasons for not testing where the exploration interest lies have all but disappeared. With any-terrain capabilities and unprecedented raw data density and overlap to support interpretation of complex conditions, that outline can be drawn through extreme rough terrain, including lakes, cliffs, industrial facilities, and grounded installations to test for generally unknown sub-surface features of potential interest.As more is learned about the larger-scale signatures of ore settings and the district-scale geo-electric imprint of hydrothermal processes on lithology, it appears that the only thing certain about ore signatures is their uncertainty. This is not bad news. New opportunities abound as the advanced 3-D technology allows a first effective look at the previously unexplorable rough terrain or complicated settings, and a second look at areas where older results may now be known to be non-definitive."

Jan 1, 2002

By Donald J. MacNeil

THE opinion, based upon geological knowledge, that certain areas within the Province of Nova Scotia might yield commercial quantities of petroleum, is not new. It dates back to at least 1864, when the Pioneer Oil and Salt Company drilled some shallow holes in search of oil near lake Ainslie, Cape Breton. As a matter of fact, several companies were engaged in oil exploratory work near lake Ainslie at about that time; included among them were the Inverness Oil and Mining Company, the Victoria Oil Company, the American Oil Company, and the Cape Breton Oil and Mining Company. Oil exploration by these and other companies was conducted sporadically on Cape Breton island until 1914. In several instances, the depth of the test holes exceeded 1,000 feet; the deepest was carried to 3,260 feet. The Lake Ainslie area was selected because oil seepages were present along certain sections of the lake shore, but the tests that were drilled to tap the oil-bearing zone failed to yield anything of commercial value. Currently, there are three areas in Nova Scotia wherein active exploratory work is being conducted, namely, at Pugsley Siding close to Amherst; at Kennetcook, Hants county; and near Mabou, Inverness county. The Pugsley Siding test is being drilled by the Sun Oil Company, of Philadelphia; the work at Kennetcook is under the direction of the Nova Scotia Oil and Gas Company; two relatively deep holes were drilled by the Lion Oil Refining Company in 1944 near Mabou, and, as a result of the additional geological information derived therefrom, another test probably will be drilled by this Company in the same area. Aside from these activities in the search for petroleum, the oil possibilities of several other sections of the Province are being studied by means of surface geological mapping.

Jan 1, 1945

By J. Chenier, M. Boissoneault, D. Ducharme, R. Schonewille

The operation of Falconbridge's Sudbury nickel smelter has undergone significant change since the production was consolidated to a single electric furnace in 1994. In the late 1990's a capital program of about $100 MM (Cdn) was undertaken to expand and modernize the smelter. This project, known as Smelter 2000, was mainly driven by the need to process the new concentrate produced at Falconbridge's Raglan operation in northern Quebec. Included in the scope of the project was the installation of dry concentrate handling facilities, modifications to the roaster feed preparation system, installation of a matte granulation system and modification of one of the converters. Improvements to in-plant hygiene were also an important part of the Smelter 2000 project. Over the past 5 years much has been learned about the challenges in treating two significantly different concentrates. More recently, the introduction of a third concentrate from Falconbridge's new Montcalm operation near Timmins, Ontario has added another dimension to the operation. This paper will describe how the main challenges from the past 7 years have been overcome and discuss the path forward for the Sudbury Smelter Business Unit.

Jan 1, 2005

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011

By The Staff

IT is a high compliment to be invited to present a pap::r on the subject of "Mining in the National Economy". To cover it adequately would need the knowledge of the economic geologist and of the technical mining engineer, together with the arts of the statistician and of the economist in general, allied with generous psychic powers. Further, one should embellish the tale with a touch of drama. It is comforting that the subject is so broad that whatever may be said within the compass of a paper like the present, can hardly be criticized as going beyond the terms of reference. A conventional approach would be to begin with the noteworthy statistics of the mining industry of yesterday and today. But in the present company this would be "carrying coals to Newcastle"-or to give the venerable metaphor local colour, "nickel to Sudbury". Such statistics are available in all their stimulating detail in our official publications. Let us tackle at once, therefore, as a less hackneyed theme, the relationship of mining to other phases of the Canadian economy. RELATION TO TOTAL PRODUCTION While mining occupies a position of less importance than manufacturing or agriculture in Canada, its relative contribution has greatly increased during the post-war period. Due to the fall in wholesale prices, the net value of production in Canada has shown a decrease averaging about 1.5 per cent per year during the post-war period, though its volume of course has gone up. Mineral production on a value basis, on the other hand, showed a gain of 2.8 per cent per year. Mineral production was only 5.14 per cent of the net value of production of all kinds of commodities in 1919, bur from 1929 to 1936 the proportion rose steadily rill it reached no less than 12. 76 per cent in the latter year.

Jan 1, 1937

By M. Askari, M. H. Parsa, S. Kashani-Nejad

Sarcheshmeh refractory consumption rate is about 7.5 - 8 kg/ton of the produced copper, which is almost three times higher than the other smelters practice. High destruction rate of tuyere zone refractory controls vessel productivity and operational lifetime. In this research with the aid of cold model and computational fluid dynamic (CFD), melt recirculation pattern and gas - liquid plume properties in the wide range of gas blowing conditions were studied. Results revealed that in addition to the well-known mechanical refractory destruction mechanism, fast tuyere zone refractory destruction could also be related to the cold bubble cluster formation near tuyere tips and introducing severe thermal shock to the refractory surface. Removing accretion and its strong bonds to the refractories around tuyere tip, causes refractory mechanical destruction and increases tuyere diameter. Increased tuyere diameter, in turn assists gas discharge in the bubbling regime. Air blowing in the bubbling regime result in the formation of big bubble clusters, bubble breakup and back attack occurrence which all found to have major impact on the refractory lifetime. Outcomes of this research, contributed to the plant converting management, blowing hardware and instrumentation improvement.

Jan 1, 2004

By J. Aiello

"A brief history of previous mining activity on Coal Mountain, near Corbin, British Columbia, is followed by a description of the steps leading up to the resumption of mining in /974 by Byron Creek Collieries. New developments, including a preparation plant, a rail spur and a totally enclosed facility, as well as operating techniques, are also discussed. IntroductionThe Corbin Mine of Byron Creek Collieries Limited is located in southeastern British Columbia, approximately 110 air miles southwest of Calgary (Fig. I), 15 miles south of Highway 3 via a newly constructed provincial road (Fig. 2). Development of the area began on July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J . Robert s, first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co. , after acquiring 15,000 acres of land in the area , began to develop a mine.F.J. Roberts was responsible for the construction of the 14-mile rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production.The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3), and production from 1908 to 1930 inclusive totalled 2,337,800 tons. This production was allocated to the mines as shown in Table 1. No.3, 4 and 6 mines were operated intermittently from 1931 to 1935."

Jan 1, 1980

By William H. Pomroy, Kenneth E. Hjelmstad

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. A fire emergency plan includes a means of warning miners of the existence of a fire, and the need to evacuate or retreat to a place of refuge. The warning alarm must be fast and must reach all miners, regardless of their location or work activity. Means of fire warning are varied, and include such methods as stench, flashing lights, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. Stench can be slow and seldom achieves total mine coverage, especially in high-back room-and-pillar mines with low ventilation velocity. Telephones are effective only where personnel are close enough to hear the phone ring. A novel fire warning alarm system has been developed by the U.S. Bureau of Mines which enables instantaneous warning of all underground personnel. The warning alarm is sent by an electromagnetic signal which penetrates through mine rock from a transmitter to small person-wearable receivers. Each miner's cap lamp battery could be equipped with a small receiver and when a fire or other emergency occurs the miner could be alerted to the danger by a blinking of the cap lamp. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This paper describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, design of the prototype transmitter and receiver, test results, and status of commercial development of systems utilizing this technology.

Jan 1, 1994